Professional Documents
Culture Documents
Enterasys Networks 2B0-011 ES Router Configuration
Enterasys Networks 2B0-011 ES Router Configuration
Enterasys Networks 2B0-011 ES Router Configuration
ES Router Configuration
Version 1.0
QUESTION NO: 1
Answer: C
QUESTION NO: 2
Which command can change the X-Pedition Router system contact name to "User One?
Answer: B
QUESTION NO: 3
Which command displays the IP Route Table on the X-Pedition Router?
C. ip show routes
D. show ip route-table
Answer: C
QUESTION NO: 4
Which one of the following statements best describes the L2 operation of the X-Pedition Router?
Answer: B
QUESTION NO: 5
A. Access
B. Trunk
C. Port-Based
D. Protocol-Based
Answer: C,D
QUESTION NO: 6
Answer: D
QUESTION NO: 7
In bootprom mode, which command displays the X-Pedition Router configuration files on the internal
flash?
A. ls /bootup/pc-flash/
B. ls /int-flash/cfg/
QUESTION NO: 8
Which command in enable mode displays the files in the int-flash/cfg/ directory?
Answer: B
QUESTION NO: 9
What is the default output-mac-encapsulation for an IPX interface on the X-Pedition Router?
A. ethernet_snap
B. ethernet_802.3
C. ethernet_802.2
D. ethernet_ii
Answer: D
QUESTION NO: 10
What is the slot numbering scheme for the XP8000 (formerly the SSR8000)?
Answer: C
QUESTION NO: 11
Answer: C
QUESTION NO: 12
What of the following would cause the X-Pedition Router to go into Boot Prom Mode?
A. a loss of power
Answer: C,D
QUESTION NO: 13
Which two of the following descriptions are characteristics of the X-Pedition Router?
D. Implementing Quality of Service and/or security Access Control Lists decreases performance
Answer: B,C
QUESTION NO: 14
Answer: A
QUESTION NO: 15
Which command displays the detailed information of all RIP packets sent and received?
Answer: C
QUESTION NO: 16
A. 3
B. 2
C. 4
D. 1
Answer: C
QUESTION NO: 17
Answer: B
QUESTION NO: 18
When multiple images are on an X-Pedition Router, which command selects the next boot image?
Answer: A
QUESTION NO: 19
What are the three major steps required to create a L3 Protocol-based VLAN?
A. Create the VLAN, add physical ports to the VLAN, and add IP/IPX address to the VLAN
B. Create the VLAN, make the trunk port, and assign a policy
D. Create the VLAN, make the trunk port, and add an IP address to the VLAN
Answer: A
QUESTION NO: 20
B. IP, IPX
C. IP, IPX and AppleTalk routed by ASICs; DECnet and Vines routed by software
Answer: B
QUESTION NO: 21
Answer: A
QUESTION NO: 22
Which method can be used to enter Boot Prom mode on the X-Pedition Router?
Answer: A
QUESTION NO: 23
Which command copies the default startup file to a backup file in ROM Monitor mode?
C. cp /startup/cfg /backup/cfg
D. cp /int-flash/cfg/startup /int-flash/cfg/backup
Answer: D
QUESTION NO: 24
D. snmp set target <IP of target> community <community name> status enable
Answer: C
QUESTION NO: 25
Answer: B
QUESTION NO: 26
D. OSPF-ASE Routes
Answer: C
QUESTION NO: 27
Answer: B
QUESTION NO: 28
Which command displays the output of the RIP Trace command on the terminal monitor?
D. rip trace on
Answer: A
QUESTION NO: 29
A. >
B. #
C. (enable)
D. !
Answer: B
QUESTION NO: 30
What is the first step to gain access to an X-Pedition Router when the password is unknown?
A. Press CTRL+ALT+DEL
B. Power cycle the router and press the ESC key to enter BootROM mode.
Answer: B
QUESTION NO: 31
What is the X-PEDITION Router's default metric for redistributing routes into RIP?
A. 14
B. 16
C. 1
D. 0
Answer: B
QUESTION NO: 32
When an L3 interface is created on the X-Pedition Router and associated with a single port, which type
of VLAN is created?
QUESTION NO: 33
What is the second step to gain access to an X-Pedition Router when the password is unknown?
D. Press CTRL+ALT+DEL
Answer: B
QUESTION NO: 34
Which two L3 multicast routing protocols does the X-Pedition Router support?
A. EIGRP
B. IGRP
C. PIM-SM
D. DVMRP
Answer: C,D
QUESTION NO: 35
Answer: B
QUESTION NO: 36
Which command displays the contents of a stored configuration file on the monitor screen?
Answer: C
QUESTION NO: 37
Which two types of VLAN ports are supported on the X-Pedition Router?
A. Access and Trunk
Answer: A
QUESTION NO: 38
During the boot process, what are all the physical ports initially added to?
A. default VLAN
B. configured VLAN
D. protocol-based VLAN
Answer: A
QUESTION NO: 39
Which type of VLAN does the X-Pedition Router define that works at L3?
A. SNA
D. IP and IPX
Answer: D
QUESTION NO: 40
What are the two Queuing Management policies on the X-Pedition Router?
Answer: D
QUESTION NO: 41
QUESTION NO: 42
Which X-Pedition Router command copies the startup configuration file to a server?
Answer: D
QUESTION NO: 43
Which two methods can be used to load an operational system image to the X-Pedition Router?
Answer: B,D
QUESTION NO: 44
A. start ospf
C. ospf start
Answer: C
QUESTION NO: 45
QoS policies can be written using information contained in which three layers of the OSI model?
Answer: C
QUESTION NO: 46
B. system image add tftp-server <tftp-server ip address> file-name <path and file name>
Answer: B
QUESTION NO: 47
Answer: B
QUESTION NO: 48
Answer: A
QUESTION NO: 49
Answer: D
QUESTION NO: 50
Which command (from Enable mode) saves the current running configuration to the startup
configuration file?
Answer: A