Professional Documents
Culture Documents
S120PII
Powered Subwoofer
Service Manual
1
S120PII Studio Series
S120PII 300W Powered Sub/ Plate Amp
LINE VOLTAGE Yes/No Hi/Lo Line Nom. Unit Notes
US 120vac/60Hz Yes 108-132 120 Vrms Normal Operation
EU 230vac/50-60Hz Yes 207-264 230 Vrms Normal operation, MOMS required
QA Test
Parameter Spec Unit Limits Conditions Notes
Amp Section
Bridge type amplifier, None of the speaker
terminals must be connected to system GND at
Type (Class AB, D, other) D n/a n/a any time.
Load Impedance (speaker) 6 Ohms n/a Nominal
Limiter prevents continuous power to exceed
Rated Output Power 275 Watts 220 1 input driven 220 Watts.
THD @ Rated Power 0.1 % 1 22k filter
THD @ 1 Watt 0.1 % 0.5 22k filter
DC Offset 10 mV-DC 60 @ Speaker Outputs
Measured at the speaker cable. 200 Watts,
measured at speaker output terminals located at
Damping factor >50 DF 23 Measured at amplifier board the amp board.
Input Sensitivity
Input Frequency 50 Hz 50 Nominal Freq.
L&R 425 mVrms ±2dB To 200 Watts Single input driven
LFE Mode selected 425 mVrms ±2dB To 200 Watts LFE Mode selected, single input driven
Bass Q Input 0.9 Vrms ±2dB To 200 Watts Single input driven
Speaker/Hi Level Input 5.5 Vrms ±2dB To 200 Watts Single input driven
Signal to Noise
SNR-A-Weighted 100 dBA 85 relative to rated power A-Weighting filter
SNR-unweighted 90 dBr 85 relative to rated power 22k filter
SNR rel. 1W-unweighted 65 dBr 60 relative to 1W Output 22k filter
Volume @max, using RMS reading
Residual Noise Floor 1 mVrms 2 DMM/VOM (or A/P)
Volume @max, w/ A/P Swept
Bandpass Measurement (Line
Residual Noise Floor 1 mVrms(max) 2 freq.+ harmonics)
Input Impedance
Line Input (L, R,LFE) 10K ohms n/a Nominal
Speaker/Hi Level Input 10K ohms n/a Nominal
Filters
LP 4th order fixed 50-150 Hz ± 10 2nd order variable and 2nd order fixed
Subsonic filter (HPF) 3rd Order Fixed
LFE Low pass 2nd order Fixed Hz ± 10 LFE input driven only
Limiter
THD at Max. Output Power YES n/a functional Maximum Output Power
Features --
Auto - On -Off switch YES -- functional Refer to ATO section
Phase switch 0-180 deg functional
Volume pot Taper (lin/log) LOG -- functional A Taper
Variable crossover 50-150 Hz YES functional
HP single order filter 180 Hz @ 8 Ohms, 90 Hz
HP Speaker out functional @ 4 Ohms load
LFE -Normal Select switch YES -- functional Disables LP filter, intended for LFE
BassQ Input YES functional 6.3mm Phono Jack
BassQ Output YES functional Bypass, loop-through - Designed for daisy chain
Input Configuration
Line In (L,R) & LFE YES -- functional Dual RCA jack
Bass Q in YES functional 6.3m phono mono Jack
Spkr/Hi Level In YES -- functional Binding post connector L&R
2
S120PII Studio Series
QA Test
Parameter Spec Unit Limits Conditions Notes
Transients/Pops
ATO Transient 5 mV-peak n/a @ Speaker Outputs
Turn-on Transient 50 mV-peak 2v-pp @ Speaker Outputs AC Line cycled from OFF to ON
Turn-off Transient 50 mV-peak 2v-pp @ Speaker Outputs AC Line cycled from ON to OFF
Efficiency
Efficiency 70 % 65 Rated power Nominal Line voltage 120 VAC
Maximum allowable input power under nominal
Input voltage and frequency, in stand-by mode
Stand-by Input Power 12 Watts 15 @ nom. line voltage (HOT or COLD operation).
Power Cons. @ rated power 400 Watts 400 @ nom. line voltage 250 Watts @ 6.0 Ohms nominal line voltage
Protection
Amplifier should resume operation after short
Short Circuit Protection YES functional Direct short at output circuit condition removal
Temperature rise in accessible metal parts
should not exceed 35K rise for domestic version
Thermal Protection YES functional @1/8 max unclipped Power or 30K rise for European versions
DC Offset Protection YES - DC present at Speaker Out leads Relay or crowbar (for driver/fire protection),
Line Fuse Rating
USA-Domestic 4 Amps Type-T or Slo Blo-250 V
EU 2 Amps Type-T or Slo Blo-250 V Internal fuse with UL/SEMKO rated holder
3
S120PII Studio Series
SPEAKER CONNECTION
When we designed the description best matches under the collar. Insert the
S120PII powered subwoofer, your system and follow the bare end of the wire through
our goal was to offer the user corresponding hookup the hole in the post, then
the best possible performance instructions. screw the collar back down
combined with the most To use the binding-post until the connection is tight.
flexible and complete speaker terminals •ª with The holes in the center of the
installation options. Please bare wire, unscrew the collar collars are intended for
look over the following three until the pass-through hole in banana-type connectors.
examples to determine which the center post is visible
Left Front Right Front
Center
Dolby* Pro Logic* (Non-Digital) – Speaker Level + – + – + –
4
S120PII Studio Series
Dolby Pro Logic (Non-Digital) – Line Level
Use this installation method in the “Normal” position. Do terminals on your receiver or
for Dolby Pro Logic appli- not use the “LFE” position amplifier.
cations (not Dolby Digital, DTS with Dolby Pro Logic-only Make sure your receiver or
or other digital processing), processors. processor is configured cor-
where the receiver/processor Note: If your receiver or rectly: Make sure that the sub-
is equipped with a subwoofer amplifier only has one woofer is configured as “On.”
output or a volume-controlled subwoofer output jack,
preamp (line-) level output: Note for advanced users: If
then you may connect the your receiver/processor has
Use RCA-type patch cords subwoofer output on your a built-in low-pass crossover
to connect the line-level receiver/preamplifier to either filter for the subwoofer output,
subwoofer outputs on your the left or right Line Level then the LFE switch ™ should
receiver or amplifier to the input ¶ on the subwoofer. It be set to the “LFE” position to
Line Level inputs ¶ on the makes no difference which bypass the subwoofer’s
subwoofer. IMPORTANT: jack you choose. internal crossover.
Make sure that the LFE toggle Connect each speaker to the
switch ™ on the subwoofer is corresponding speaker
¡ ™ £
180° LFE ON
PHASE AUTO
0° NORMAL OFF
RECEIVER 80Hz ¢
Subwoofer
CROSSOVER
FREQUENCY LEVEL ∞
Out
L R 50Hz 150Hz MIN MAX
§
LINE
BASSQ
(See owner’s
LEVEL IN
(For LFE
¶
manual use R or L)
before use) IN OUT R L
HIGH
LEVEL
IN
•
R
+ –
HIGH
LEVEL
OUT
ª
R
5
S120PII Studio Series
Dolby Digital or DTS (or Other Digital Surround Mode) Connection
Use this installation method Note: If your receiver or Make sure that you have
for Dolby Digital, DTS or other amplifier has only one configured your surround
digital surround processors: subwoofer output jack, sound processor for
IMPORTANT: Make sure that then you may connect the “Subwoofer On” or “LFE On.”
the LFE toggle switch ™ on subwoofer output on your The front left, front right,
the subwoofer is in the “LFE” receiver/preamplifier to either center and rear speakers
position. Use the Line Level the left or right Line Level should be set to “Small” or
input jacks ¶ for the Low- input ¶ on the subwoofer. It “Large” depending on their
Frequency Effects channel. makes no difference which size and frequency response.
Connect these jacks to the jack you choose. Consult your receiver’s or
LFE output or subwoofer Connect each speaker to the processor’s owner’s manual.
output on your receiver or corresponding speaker
amplifier. terminals on your receiver or
amplifier.
¡ ™ £
180° LFE ON
PHASE AUTO
0° NORMAL OFF
80Hz ¢
RECEIVER/PREAMPLIFIER CROSSOVER
FREQUENCY LEVEL ∞
Subwoofer 50Hz 150Hz MIN MAX
Output/LFE §
LINE
BASSQ
(See owner’s
LEVEL IN
(For LFE
¶
manual use R or L)
before use) IN OUT R L
HIGH
LEVEL
IN
•
R
+ –
HIGH
LEVEL
OUT
ª
R
BassQ™ Jacks
The jacks marked “BassQ” § your system’s bass response device. Do not use the BassQ
are for use with the JBL by equalizing the output of jacks § without having first
BassQ bass equalization multiple subwoofers to read the BassQ owner’s
module that will be released best match your listening manual.
in the near future. The BassQ environment. DO NOT con-
will enable you to optimize nect these jacks to any other
6
S120PII Studio Series
O P E R AT I O N
Power
The S120PII is equipped with Auto As long as no audio return to Standby mode,
both a master Power switch signal is received, the indicated by the LEDs
‚ and an Auto turn-on/turn- subwoofer is in Standby turning red.
off switch £. In order to mode to conserve Off The subwoofer is off at
function, the S120PII must power, indicated by the all times, even if an
be plugged into an active red color of the LEDs on audio signal is present
electrical outlet (but not an the front of the unit. at its inputs.
accessories outlet on another When an audio signal is If you plan to be away for an
component of your audio sensed, the subwoofer extended time, or if the
system such as a receiver), will switch itself into the subwoofer will not be used,
and the master Power switch fully On mode and begin you may wish to turn off the
‚ must be turned on playing the program master Power switch ‚.
(the “•” position). material. The LEDs will
The Auto turn-on/turn-off turn green. When a
switch £ has three positions: period of about twenty
On The subwoofer is on at minutes goes by during
all times and ready to which no signal is
play program material. sensed, the S120PII will
Level Control
The subwoofer Level Control room size, subwoofer When using a Dolby Digital/
∞ adjusts the volume of the placement, type of main DTS receiver, adjust the LFE
subwoofer relative to the rest speakers and listener position. level on the receiver to 0dB,
of the system. Proper level Adjust the subwoofer level so and then adjust the subwoofer
adjustment depends on that the volume of the bass Level Control ∞ for the
several variables such as information is pleasing to you. desired amount of bass.
Crossover Adjustments
The Crossover Frequency between 120Hz – 150Hz. This the LFE switch ™ is in the
Control ¢ determines the control ¢ is not used when “LFE” position.
highest frequency at which the
¡ ™ £
subwoofer reproduces sounds.
If your main speakers can 180° LFE ON
efforts on the ultradeep bass L WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
HIGH
+ –
using smaller bookshelf L
ON
7
S120PII Studio Series
Phase Control
subwoofer placement and you happen to rearrange your
listener position. Adjust the listening room and move
Phase switch ¡ to maximize your speakers, you should
bass output at the listening experiment with the Phase
position. switch ¡ in both positions,
The Phase Control ¡ Remember, every system, and leave it in the position
determines whether the room and listener is different. that maximizes bass
subwoofer’s piston-like action There are no right or wrong performance.
moves in and out in phase settings; this switch ¡ offers
with the main speakers or the added flexibility to adjust
opposite the main speakers. your subwoofer for optimum
There is no correct or performance for your specific
incorrect setting. Proper listening conditions without
phase adjustment depends on having to move your speakers.
several variables such as If at some time in the future
TROUBLESHOOTING
If you used the High Level If there is low (or no) bass If you used the Line Level
(speaker) inputs • and there output: inputs ¶ and there is no
is no sound from any of the sound from the subwoofer:
• Make sure the connections
speakers: to the left and right “Speaker • Check that receiver/amplifier
• Check that receiver/amplifier Inputs” • have the correct is on and a source is playing.
is on and a source is playing. polarity (+ and –). • Check that powered
• Check that powered • Make sure that the subwoofer is plugged into an
subwoofer is plugged into subwoofer is plugged into an active electrical outlet and
an active electrical outlet active electrical outlet and that both Power switches
and is switched on £‚. that both power switches are on £‚.
• Check all wires and are on £‚. • Check all wires and con-
connections between • Adjust the Crossover point nections between receiver/
receiver/amplifier and ¢. amplifier and subwoofer.
speakers. Make sure all wires • Flip the Phase Control Make sure all wires are
are connected. Make sure switch ¡ to the opposite connected. Make sure none
none of the speaker wires position. of the wires are frayed, cut
are frayed, cut or punctured. • If you are using a Dolby or punctured.
Make sure no wires are Digital/DTS receiver or • Review proper operation of
touching other wires or processor, make sure that the your receiver/amplifier.
terminals and creating a subwoofer adjustments on • Slowly turn the Level
short circuit. the receiver/processor are Control ∞ clockwise until
• Review proper operation set up correctly. When using you begin to hear the desired
of your receiver/amplifier. the S120PII’s Speaker Level amount of bass.
inputs •, you should set your • Make sure that you have
receiver to configure the configured your receiver/
main left and right speakers processor so that the
as “LARGE”. subwoofer/LFE output is on.
• Slowly turn the Level
Control ∞ clockwise until
you begin to hear the desired
amount of bass.
8
Service Bulletin
Model: S120PII
In the event you receive an S120PII subwoofer with the complaint “There is a brief chirping sound, or
short oscillation that occurs when the unit is in the AUTO mode, in Standby, when it’s triggered ON
with a music signal”, follow the procedure below to correct this condition:
Synopsis: Replace D60 (RLS4148 diode) with a 3.6V Zener Diode; add new Resistor.
1) Remove the amplifier assembly from the subwoofer cabinet (12 Phillips screws).
2) Remove the Plastic Amp Cover from the faceplate (4 Phillips screws).
3) The area of concern is on the Class D Driver PCB (Small Upright PCB on the MAIN AMP PCB). A
long, thin, soldering iron tip is recommended. Care must be taken not to damage surrounding
components, like large inductor pair L8.
4) Locate, remove D60 (RLS4148 diode); replace with a 3.6V zener diode, JBL Part# ZMM5227BCT-ND.
When replacing D60 the polarity of the new (zener) diode should be reversed.
5) Add new 27KΩ resistor, JBL Part# 299-27K, to the indicated connections. (This component,
electrically, will be in parallel with R37, reducing its value to <22KΩ). Assure the leads do not come
into contact with any other connections; insulate the leads if necessary.
6) Replace amp cover and return amplifer assembly to cabinet.
7) Test the subwoofer to assure the distortion is no longer present.
9
S120PII Studio Series
S120PII BLOCK DIAGRAM
10
S120PII
Studio™ Series
EXPLODED VIEW
Top Plate
337898-001 Port Tube
Top Plate Gasket 337859-001
338012-001
(12) Screws
LED Indicator Assembly PB, HXS. #8 x .75"
335650-001 903802-012
12" Woofer
338008-001
Amplifier Assembly
Not for Sale
Studio Series
(4) Rubber Foot Assembly
338037-001
(8) Screws PB, HXS. #8 x .75"
903802-012
S120PII
Front Grille
338007-001
11
S120PII Test Set Up and Procedure
Sweep Function
1. Follow steps 1-5 above, using a sweep generator as a signal source.
2. Sweep generator from 20Hz to 1kHz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or
any other noises. If any unusual noises are heard, remove woofer and test.
12
S120PII Studio Series
S120PII ELECTRICAL PARTS LIST
Amplifier PCB
Resistors
Capacitors
13
S120PII Studio Series
Part Number Qty Description Reference Designator
Semiconductors
Miscellaneous
Resistors
14
S120PII Studio Series
Part Number Qty Description Reference Designator
024-100698-120 1 SMD resistor 100K 1/8W J 0805 TAPING R37
024-110598-120 2 SMD resistor 11K 1/8W J 0805 TAPING R74,99
024-200598-120 2 SMD resistor 20K 1/8W J 0805 TAPING R95,141
024-220398-120 2 SMD resistor 220R 1/8W J 0805 TAPING R136,167
024-220498-121 1 SMD resistor 2K2 1/8W J 0805 TAPING R134
024-220798-120 2 SMD resistor 2M2 1/8W J 0805 TAPING R87,93
024-270498-120 3 SMD resistor 2K7 1/8W J 0805 TAPING R80,84,157
024-390498-120 2 SMD resistor 3K9 1/8W J 0805 TAPING R130,161
024-390598-120 2 SMD resistor 39K 1/8W J 0805 TAPING R86,94
024-470398-120 1 SMD resistor 470R 1/8W J 0805 TAPING R91
024-470498-120 6 SMD resistor 4K7 1/8W J 0805 TAPING R151-153,183,34,36
024-470598-120 1 SMD resistor 47K 1/8W J 0805 TAPING R35
024-470698-120 2 SMD resistor 470K 1/8W J 0805 TAPING R32,33
024-560598-120 1 SMD resistor 56K 1/8W J 0805 TAPING R38
024-680498-120 2 SMD resistor 6.8K 1/8W J 0805 TAPING R135,166
Capacitors
Semiconductors
15
S120PII Studio Series
Part Number Qty Description Reference Designator
Miscellaneous
Pre/Input PCB
Resistors
Capacitors
16
S120PII Studio Series
Part Number Qty Description Reference Designator
031-100343-100 2 SMD capacitor 100pF/50V J 0805 NPO TAPING C222,204
031-100344-100 7 SMD capacitor 0u1/50V K 0805 X7R TAPING C227,232,233,229,234,235,230
031-220244-101U 1 SMD capacitor 0u022/50V K 0805 X7R TAPING C202
031-220344-100 2 SMD capacitor 220pF/50V J 0805 NPO TAPING C210,200
031-470144-101 1 SMD capacitor 0u0047/50V K 0805 X7R TAPING C219
031-680144-100 1 SMD capacitor 0u0068/50V K 0805 X7R TAPING C212
033-200695-300 2 NP Electrolytic capacitor 200u/63V M (R)1326 P:5 C205,203
034-100525-301 1 Electrolytic capacitor 10uF/25V M (R) P:2 TAPING C220
034-220525-300 4 Electrolytic capacitor 22uF/25V M (R) 5x11 P:2.5 C15,14,223,225
034-220625-300 1 Electrolytic capacitor 220uF/25V M (R)0812 P:5 TAPING C221
038-100363-300 2 MPE capacitor P:5 0u1/100V J TAPING C201,209
038-150393-300 2 MPE capacitor 0u15/63V J P:5 TAPING C208,207
038-680393-300 1 MPE capacitor 0u68/63V J P:5 TAPING C214
Semiconductors
17
S120PII Studio Series
Part Number Qty Description Reference Designator
074-030018-000 1 Toggle Switch PN:L103-T2-B4 SW202
Fuse PCB
Miscellaneous
18
Part Number Qty Description Reference Designator
071-060280-500 4 nut washer 8#-32 zinc plated 8.5 t=3m/m For Transformer
071-100606-060 2 flat washer PN:WS3-2 OD=6 ID=3.t=2mm nylon For Q11,Q13
073-014044-000 1 Bracket 6.64"x3.50"x3.20" SPCC cadium plated
074-020018-000 1 Rocker Switch (Power) PN:RF1003-BB4-0 SW4
082-022241-000 1 Wire #22 UL1007 L=410mm blk/wht XH2P+HWAFER
082-072620-000 1 Wire #26 UL1007 L=200mm XH7Px2 blk+whtx6
086-021836-000 1 Double insulated cable SPT-2 #18 12feet +T187 Power cord
181-911600-158 1 Wire #16AWG UL1007 blk L=720mm
181-911622-148 1 Wire #16AWG UL1007 red L=720
181-921600-000 1 BLKWire #16 UL1015 both ends T187 trans sleeve L:140mm
181-921699-000 1 WHT Wire #16 UL1015 both ends T187 transp sleeve L:160mm
19
S120PII Studio Series
20
S120PII Studio Series
21
S120PII Studio Series
22
S120PII Studio Series
23
S120PII Studio Series
24
S120PII Studio Series
25
S120PII Studio Series
Or part may be
TL072CDR
26
S120PII
Studio™ Series
PACKAGING
Studio™ Series
S120PII
27