Professional Documents
Culture Documents
PD 1 Form A
TYPICAL APPLICATIONS
1 4
Measuring and Testing equipment
IC Testers and Board Testers
High speed inspection machines
2 3 Note: Please contact our sales representative for automotive applications of PhotoMOS.
(Unit: mm)
TYPES
RATING
f = 100 Hz,
Peak forward current IFP 1A
Duty Ratio = 0.1%
Power dissipation Pin 75 mW
Load voltage (peak AC) VL 60 V 100 V 200 V 400 V
Continuous load current IL 2.0 A 1.3 A 0.65 A 0.35 A Peak AC, DC
Output
100 ms (1 shot),
Peak load current Ipeak 6.0 A 4.0 A 2.0 A 1.0 A
VL = DC
Power dissipation Pout 700 mW
Total power dissipation PT 750 mW
I/O isolation voltage Viso 2,500 Vrms
(Avoid icing and
Ambient temperature (Operating) Topr -40 to +85°C
condensation)
Ambient temperature (Storage) Tstg -40 to +100°C
IFoff
current Typical 0.9 mA VL = 10 V
Input
90%
10%
Output
Ton Toff
REFERENCE DATA
1.Load current vs. ambient temperature 2-1.On resistance vs. ambient temperature 2-2.On resistance vs. ambient temperature
characteristics characteristics characteristics
Allowable ambient temperature: –40 to +85°C LED current: 10 mA; LED current: 10 mA;
Continuous load current: 2.0 A (DC) (AQY272), Continuous load current: 0.65 A (DC) (AQY277),
1.3 A (DC) (AQY275) 0.35 A (DC) (AQY274)
3.5 0.5 5
3.0
0.4 4
AQY274
On resistance (Ω)
On resistance (Ω)
2.5
Load current (A)
AQY275
AQY272 0.3 3
2.0
0 0 0
-40 -20 0 20 40 60 80 85 100 -40 -20 0 20 40 60 8085 -40 -20 0 20 40 60 8085
Ambient temperature (°C) Ambient temperature (°C) Ambient temperature (°C)
3.Turn on time vs. ambient temperature 4.Turn off time vs. ambient temperature 5.LED operate current vs. ambient
characteristics characteristics temperature characteristics
LED current: 10 mA; Load voltage: 10 V (DC); LED current: 10 mA; Load voltage: 10 V (DC); Load voltage: 10 V (DC);
Continuous load current: 100 mA (DC) Continuous load current: 100 mA (DC) Continuous load current: 100 mA (DC)
10 1.0 5
8 0.8 4
LED operate current (mA)
Turn off time (ms)
Turn on time (ms)
6 0.6 3
AQY272
AQY274
4 0.4 2 AQY272
AQY277
AQY275
AQY277 AQY275
2 AQY274 0.2 AQY275 1
AQY272
AQY277 AQY274
0 0 0
-40 -20 0 20 40 60 80 85 -40 -20 0 20 40 60 80 85 -40 -20 0 20 40 60 80 85
Ambient temperature (°C) Ambient temperature (°C) Ambient temperature (°C)
Current (A)
1.4
4
LED turn off current (mA)
AQY272
0 0 -4
-40 -20 0 20 40 60 80 85 -40 -20 0 20 40 60 80 85
Ambient temperature (°C) Ambient temperature (°C)
9-1.Off state leakage current vs. load 9-2.Off state leakage current vs. load 10.Turn on time vs. LED forward current
voltage characteristics voltage characteristics characteristics
Ambient temperature: 25°C Ambient temperature: 25°C Load voltage: 10 V (DC); Continuous load current:
100 mA (DC); Ambient temperature: 25°C
20
10-3 10-3 18
Off state leakage current (A)
16 AQY272
AQY275
AQY274 8
10-9 10-9
AQY275 6
AQY277 AQY274
AQY272 4
AQY277
10-12 10-12 2
0
0 50 100 0 50 100 0 10 20 30 40 50
Load voltage (V) Load voltage (V) LED forward current (mA)
11.Turn off time vs. LED forward current 12-1.Turn on time vs. load voltage 12-2.Turn on time vs. load voltage
characteristics characteristics characteristics
Load voltage: 10 V (DC); Continuous load current: LED current: 10 mA; Continuous load current: LED current: 10 mA; Continuous load current:
100 mA (DC); Ambient temperature: 25°C 100 mA; Ambient temperature: 25°C 100 mA; Ambient temperature: 25°C
0.5 5 5
0.4 4 4
Turn on time (ms)
Turn off time (ms)
0.3 3 3
AQY275 AQY272
0.2 AQY272 2 2
AQY275 AQY274
AQY277
0.1 1 1
AQY274 AQY277
0 0 0
0 10 20 30 40 50 0 10 20 30 40 50 60 70 80 90 100 0 50 100 150 200 250 300 350 400
LED forward current (mA) Load voltage (V) Load voltage (V)
4 4 0.4
AQY275
3 AQY272 3 0.3
AQY272
2 2 AQY274 0.2 AQY275
AQY277
1 1 0.1
0 0 0
0 0.5 1.0 1.5 2.0 2.5 3.0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 0 10 20 30 40 50 60 70 80 90 100
Load current (A) Load current (A) Load voltage (V)
14-2.Turn off time vs. load voltage 15-1.Turn off time vs. load current 15-2.Turn off time vs. load current
characteristics characteristics characteristics
LED current: 10 mA; Continuous load current: LED current: 10 mA; Load voltage 10 V (DC); LED current: 10 mA; Load voltage 10 V (DC);
100 mA; Ambient temperature: 25°C Ambient temperature: 25°C Ambient temperature: 25°C
0.5 0.5 0.5
AQY272
0.2 0.2 0.2
AQY275
AQY277
0.1 0.1 0.1 AQY277
AQY274 AQY274
0 0 0
0 50 100 150 200 250 300 350 400 0 0.5 1.0 1.5 2.0 2.5 3.0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
Load voltage (V) Load current (A) Load current (A)
16.Max. operating frequency vs. load 17.Output capacitance vs. applied voltage
voltage and load current characteristics characteristics
Sample: All types; LED current: 10 mA; Frequency: 1 MHz;
Ambient temperature: 25°C Ambient temperature: 25°C
VL: Load voltage, VL (Max.): Max. rated load voltage
IL: Load current, IL (Max.): Max. rated continuous load current
10 2000
duty = 50%
9 1800
Max. operating frequency (cps)
8 1600
Output capacitance (pF)
7 1400
AQY272
6 1200
5 1000
4 800
3 600
AQY275 AQY277
2 400 AQY274
1 200
0 0
0 10 20 30 40 50 60 70 80 90 100 0 20 40 60 80 100
VL × I L
VL (max.) × IL (max.)
×100 (%) Applied voltage (V)
DIMENSIONS CAD The CAD data of the products with a “CAD” mark can be downloaded from our Website. Unit: mm
CAD Through hole terminal type CAD Surface mount terminal type PC board pattern
External dimensions External dimensions (BOTTOM VIEW)
5.08
4-0.8 dia.
0 to 10° Max.10°
10.16
8.8
2.54
1
10.16 ±0.05
Tolerance: ±0.1
8.8±0.2
10.16
8.8 ±0.2
Recommended mounting pad
(TOP VIEW)
9.3±0.2
0 to 10° 9.3 ±0.2
11
3.5±0.1
3.9 ±0.2
1.8
3.5±0.2
1.8
3
0.2+0.2
ー0
5.08
1.4 Terminal thickness: t = 0.25 5.08
5.08 General tolerance: ±0.1 Terminal thickness: t = 0.25 Tolerance: ±0.1
General tolerance: ±0.1
Output Load
Schematic Connection Wiring diagram
configuration type
1 4 4 Load
1 4
E1
1 Form A AC/DC - IF IL VL (AC, DC) IL VL (AC, DC)
2 3 3
2 3
Load
SAFETY STANDARDS
SAFETY WARNINGS
o not use the product under conditions that exceed the range
D heck the wiring diagrams in the catalog and be sure to
C
of its specifications. It may cause overheating, smoke, or fire. connect the terminals correctly. If the device is energized
Do not touch the recharging unit while the power is on. There with short circuit or any wrong connection, it may cause
is a danger of electrical shock. Be sure to turn off the power unexpected malfunction, abnormal heat or fire.
when performing mounting, maintenance, or repair operations
on the device (including connecting parts such as the terminal
board and socket).
Derating design
Derating is a significant factor for reliable design and product life. 5) When packing printed circuit boards and equipment, avoid using
Even if the conditions of use (temperature, current, voltage, etc.) of high-polymer materials such as foam styrene, plastic, and other
the product are within the absolute maximum ratings, reliability may materials which carry an electrostatic charge.
be lowered remarkably when continuously used in high load 6) When storing or transporting PhotoMOS®, the environment should
conditions (high temperature, high humidity, high current, high not be conducive to generating static electricity (for instance, the
voltage, etc.) Therefore, please derate sufficiently below the humidity should be between 45% and 60%), and PhotoMOS®
absolute maximum ratings and evaluate the device in the actual should be protected using conductive packing materials.
condition.
Moreover, regardless of the application, if malfunctioning can be Unused terminals
expected to pose high risk to human life or to property, or if products The No. 3 terminal is used with the circuit inside the device.
are used in equipment otherwise requiring high operational safety, in Therefore, do not connect it to the external circuitry with either
addition to designing double circuits, that is, incorporating features connection method A, B or C. (1 Form A 6-pin type)
such as a protection circuit or a redundant circuit, safety testing
should also be carried out. Short across terminals
Do not short circuit between terminals when device is energized,
pplying stress that exceeds the absolute maximum
A since there is possibility of breaking of the internal IC.
rating
If the voltage or current value for any of the terminals exceeds the Surge voltages at the input
absolute maximum rating, internal elements will deteriorate because If reverse surge voltages are present at the input terminals, connect
of the overvoltage or overcurrent. In extreme cases, wiring may a diode in reverse parallel across the input terminals and keep the
melt, or silicon P/N junctions may be destroyed. reverse voltages below the reverse breakdown voltage.
Therefore, the circuit should be designed in such a way that the load Typical circuits are below shown.
never exceed the absolute maximum ratings, even momentarily. 1) 6-pin
Clamp diode is
100
connected in parallel
with the load.
80 1 6
LED forward current (mA)
2 5
60
Load
3 4
40
CR snubber is
connected in parallel
20
with the load.
2) Please make sure the LED forward current for Emax. is no higher
than 50 mA. 1 2 3 4
Load
CR snubber is
3) Please maintain the input voltage at least 4V for Emin. (GU, RF
connected in parallel
and Power voltage-sensitive type). with the load.
4) Please make sure the input voltage for Emax. is no higher than 6V
(GU and RF voltage-sensitive type). 4
1 2 3
Load A varistor is
5) Please make sure the input voltage for Emax. is no higher than 30V connected in parallel
(Power voltage-sensitive type). with PhotoMOS®
(3) TSON
1 4
Load
2 3
Emin. Emax.
Clamp diode is
connected in parallel
6) Please maintain the input voltage at least 3V for Emin. (for TSON)
with the load.
1 4
7) Please make sure the input voltage for Emax. is no higher than 5.5V.
(for TSON) Load
2 3
8) Please keep amplitude voltage of ripple within ±0.5V. (for TSON) CR snubber is
connected in parallel
with the load.
within ±0.5 V
Set voltage
2) When Clamp diode or CR Snubber is used in the circuit, the spike
voltages from the load are limited. But the longer wire may
within ±0.5 V become the inductance and cause the spike voltage. Keep the
wire as short as possible.
Water condensation
Water condensation occurs when the ambient temperature changes
suddenly from a high temperature to low temperature at high
humidity, or the device is suddenly transferred from a low ambient
temperature to a high temperature and humidity. Condensation
causes the failures such as insulation deterioration. Panasonic
Corporation does not guarantee the failures caused by water
condensation. The heat conduction by the equipment the
PhotoMOS® is mounted may accelerate the water condensation.
Please confirm that there is no condensation in the worst condition
of the actual usage. (Special attention should be paid when high
temperature heating parts are close to the PhotoMOS®.)
1.75±0.1
Tractor feed holes 1.5 +0.5
-0 dia.
0.2 ±0.05 2.2±0.2 4±0.1 2±0.5
2.4±0.2
180±3dia.
60 ±3dia.
TSON
±0.3
4-pin
12
Device mounted
on tape
±0.3 1.05±0.1dia.
5.5±0.1
1.2 2±0.1
4±0.1
13±0.5 dia.
(1) When picked from 1/2-pin side: Part No. AQY2C1R*PX (Shown above) 13±1.5 1.2±0.5
*Quality of material: Polystyrene (PS)
(2) When picked from 3/4-pin side: Part No. AQY2C1R*PZ
Direction of picking
1.75±0.1
0.4 ±0.05 4.0 ±0.1
2.4±0.2
2.5±0.2
±0.3
VSSOP
12.0
4-pin Device mounted
on tape
3.3±0.3 1±0.1dia. 8±0.1 2±0.1
5.5±0.1
(1) When picked from 1 and 4-pin side: Part No. AQY*TY (Shown above)
(2) When picked from 2 and 3-pin side: Part No. AQY*TW
Direction of picking
1.75±0.1
SON
±0.3
21±0.8
12
2±0.3
2±0.5
(1) When picked from 1 and 4-pin side: Part No. AQY*MY (Shown above)
250 ±2dia.
80 ±1 dia.
(2) When picked from 2 and 3-pin side: Part No. AQY*MW
Direction of picking
1.75±0.1
on tape
2.7±0.3 4.0±0.1
1.5+0.1
ー 0 dia.
(1) When picked from 1 and 4-pin side: Part No. AQY*VY, APV2111VY (Shown above)
(2) When picked from 2 and 3-pin side: Part No. AQY*VW, APV2111VW
Direction of picking
1.75±0.1
SOP
12
(1) When picked from 1/2-pin side: Part No. AQY*SX, APV**21SX (Shown above)
(2) When picked from 3/4-pin side: Part No. AQY*SZ, APV**21SZ
Note: “ * ” indicates characters of number or alphabet.
21±0.8
80 ±1dia.
Direction of picking
1.75±0.1
Tractor feed holes ±0.1
0.3±0.05 1.55±0.05dia. 4 7.2±0.1
2±0.5
5.5±0.1
±0.3
250 ±2dia.
80 ±1 dia.
6.9 ±0.1
SOP
12
6-pin Device mounted on tape
12±0.1 2±0.1 1.55±0.1dia.
2.8±0.3
(1) When picked from 1/2/3-pin side: Part No. AQV*SX (Shown above) *Quality of material: Paper 13 ±0.5dia. 14±1.5 2 ±0.5
(2) When picked from 4/5/6-pin side: Part No. AQV*SZ
Direction of picking
1.75±0.1
Tractor feed holes
0.3±0.05 1.55±0.05dia. 7.5±0.1
7.5±0.1
10.15±0.1
16±0.3
SOP
8-pin Device mounted 21±0.8
on tape
80 ±1dia.
4±0.1 1.55±0.1dia.
2.8±0.3
12±0.1 2±0.1
2±0.5
(1) When picked from 1/2/3/4-pin side: Part No. AQW*SX (Shown above)
(2) When picked from 5/6/7/8-pin side: Part No. AQW*SZ
250 ±2 dia.
80 ±1dia.
Direction of picking
1.75±0.1
16±0.3
4±0.1 1.55±0.1dia.
2.8±0.3 12±0.1 2±0.1
(1) When picked from 1/2/3/4/5/6/7/8-pin side: Part No. AQS*SX (Shown above)
(2) When picked from 9/10/11/12/13/14/15/16-pin side: Part No. AQS*SZ
21±0.8
80 ±1dia.
Direction of picking
1.75±0.1
12±0.3
5.25±0.1
Surface mount
terminal Device mounted on tape
12±0.1 2±0.1 1.55±0.1dia.
4.2±0.3
(1) When picked from 1/2-pin side: Part No. AQY*HAX, AQY210HLAX (Shown above) *Quality of material: Paper 13±0.5dia. 13.5±2.0 2±0.5
(2) When picked from 3/4-pin side: Part No. AQY*HAZ, AQY210HLAZ
21±0.8
80 ±1dia.
Direction of picking
1.75±0.1
300±2dia.
DIP 6-pin
80±1dia.
±0.3
9.2±0.1
Surface mount
16
(1) When picked from 1/2/3-pin side: Part No. AQV*AX (Shown above) *Quality of material: Paper 13 ±0.5dia. 17.5±2 2±0.5
(2) When picked from 4/5/6-pin side: Part No. AQV*AZ
Note: “ * ” indicates characters of number or alphabet.
Direction of picking
1.75±0.1
Tractor feed holes ±0.1
0.3 ±0.05
1.5+0.1
ー0 dia.
4 10.1±0.1
DIP 8-pin
7.5±0.1
Surface mount
10.2±0.1
±0.3
terminal
16
21±0.8
(Basic insulation Device mounted on tape
80 ±1dia.
type) 12±0.1 2±0.1 1.55±0.1dia.
4.5±0.3
2±0.5
(1) When picked from 1/2/3/4-pin side: Part No. AQW*AX (Shown above)
(2) When picked from 5/6/7/8-pin side: Part No. AQW*AZ
300±2dia.
80±1dia.
Direction of picking
1.75±0.1
Tractor feed holes
0.3±0.05 1.5 +0.1
ー0 dia.
4±0.1 10.2±0.1
DIP 8-pin
7.5±0.1
Surface mount
10.3±0.1
16±0.3
terminal *Quality of material: Paper 13 ±0.5dia. 17.5±2 2±0.5
(Reinforced Device mounted on tape
insulation type 12±0.1 2±0.1 1.55±0.1dia.
4.2±0.3
21±0.8
100±1dia.
Direction of picking
±0.1
0.3±0.05 1.55+0.05
ー 0.05 dia.
4.0±0.1 12.6±0.1
2±0.5
11.5 ±0.1
330±2 dia.
Power-DIP
100±1dia.
24.0 ±0.3
4-pin
9.7±0.1
(1) When picked from 1/2-pin side: Part No. AQY*AX (Shown above) *Quality of material: Paper 13 ±0.5dia. 25.5±2 1.7±0.8
(2) When picked from 3/4-pin side: Part No. AQY*AZ
21±0.8
80 ±1dia.
Direction of picking
1.75±0.1
DIP 6-pin
±0.3
9.2±0.1
300±2dia.
Surface mount 80±1dia.
16
terminal
Device mounted on tape
(Photovoltaic
MOSFET driver) 12±0.1 4±0.1 1.6±0.1dia.
±0.3
4.5
2±0.1
(1) When picked from 1/2/3-pin side: Part No. APV1122AX (Shown above) *Quality of material: Paper 13 ±0.5dia. 17.5±2 2±0.5
(2) When picked from 4/6-pin side: Part No. APV1122AZ
Note: “ * ” indicates characters of number or alphabet.
2) Tube
Devices are packaged in a tube so that 1-pin is on the stopper B
side. Observe correct orientation when mounting them on PC
boards.
(PD type) (SOP type)
Stopper B Stopper A
DC AQZ192 60 V DC 10 A DC 5, 12, 24 V DC
type AQZ197 200 V DC 5 A DC 100 V DC
12 V AC
AQZ202G Peak AC, DC 60 V Peak AC, DC 6 A
5, 12, 24 V DC
24 V AC
AC/ AQZ205G Peak AC, DC 100 V Peak AC, DC 4 A 48 V DC
DC
type AQZ207G Peak AC, DC 200 V Peak AC, DC 2 A 48 V AC
100 V DC
120, 240 V AC
AQZ206G2 Peak AC, DC 600 V Peak AC, DC 1 A
200, 400 V DC