Professional Documents
Culture Documents
Fibeair 1500Hp/Rfu-Hp: Installation Guide
Fibeair 1500Hp/Rfu-Hp: Installation Guide
Installation Guide
Notice
This document contains information that is proprietary to Ceragon Networks Ltd. No part of this
publication may be reproduced, modified, or distributed without prior written authorization of
Ceragon Networks Ltd. This document is provided as is, without warranty of any kind.
Trademarks
Ceragon Networks®, FibeAir® and CeraView® are trademarks of Ceragon Networks Ltd.,
registered in the United States and other countries.
Ceragon® is a trademark of Ceragon Networks Ltd., registered in various countries.
CeraMap™, PolyView™, EncryptAir™, ConfigAir™, CeraMon™, EtherAir™, CeraBuild™, CeraWeb™,
and QuickAir™, are trademarks of Ceragon Networks Ltd.
Other names mentioned in this publication are owned by their respective holders.
Statement of Conditions
The information contained in this document is subject to change without notice. Ceragon
Networks Ltd. shall not be liable for errors contained herein or for incidental or consequential
damage in connection with the furnishing, performance, or use of this document or equipment
supplied with it.
Information to User
Any changes or modifications of equipment not expressly approved by the manufacturer could
void the user’s authority to operate the equipment and the warranty for such equipment.
Table of Contents
1. About This Guide.............................................................................................. 7
When working with a FibeAir IDU, note the following risk of electric
shock and energy hazard: Disconnecting one power supply disconnects
! only one power supply module. To isolate the unit completely,
disconnect all power supplies.
Beachten Sie beim Arbeiten mit FibeAir IDU das folgende Stromschlag-
und Gefahrenrisiko: Durch Abtrennen einer Stromquelle wird nur ein
! Stromversorgungsmodul abgetrennt. Um die Einheit vollständig zu
isolieren, trennen Sie alle Stromversorgungen ab.
3. Target Audience
This guide contains technical information about 1500HP/RFU-HP installation, and
is intended for use by qualified Ceragon technical personnel at all levels.
4. Related Documents
FibeAir IP-20N Installation Guide – DOC-00040492
FibeAir IP-20A Installation Guide – DOC-00040961
FibeAir IP-20G Installation Guide – DOC-00041192
FibeAirIP-10G Installation Guide –DOC-00023199
FibeAir IP-10E Installation Guide –DOC-00029444
FibeAir IP-10Q Installation Guide, DOC-00029546
5. Important Notes
1500HP/RFU-HP is intended for installation in a Restricted Access
Location.
1500HP/RFU-HP must be installed and permanently connected to
protective earth by qualified service personnel in accordance with
applicable national electrical codes.
The FibeAir system is to be installed in Network Telecommunication
Facilities.
This installation guide describes installations using the newer type OCB. For
installation procedures using the older type OCB, refer to Revision B and older
versions of this Installation Guide.
The OCB is optimized for configurations that do not use IFC Space Diversity.
To support IFC Space Diversity, a diversity block is added.
The OCB has just one type, and can be connected to an antenna via a flexible
waveguide.
The OCB connection is at the rear of the OCB. It includes proprietary
accessories (different than those used for the older OCB).
Each OCB has three waveguide access points: The In/Out port is located at the
rear of the OCB.
The OCB ports include:
Tx port
Rx Port
Diversity port
If the system is not configured for diversity, all the relevant access points on
the OCB must be terminated using waveguide shorts. Unused Rx ports will be
terminated with a WG termination.
28/30 No No 15OCBf-xxxy-nn-L/H
MHz Yes No 15OCBf-SD-xxxy-nn-L/H
11 GHz
No No 15OCB11w-xxxy-nn-L/H
40 MHz
Yes No 15OCB11w-SD-xxxy-nn-L/H
1 Insert two screws (3) into the two lower hanging profile (4) holes and
secure them with four nuts (1) and two washers (2) (do not tighten) (Step
I in illustration below).
2 Arrange the OCBs (5) in a straight line and place the hanging profile (4)
(Step II).
WARNING!
1 Carefully insert the RFUs (2) into the slots on the OCB units (1).
2 Fasten two screws (3) using the angled Allen wrench. The torque for the
screws should be 12Nm.
Description Quantity
Pillar Housing 1
Hanging Profile 1
Screw, Phillips Pan head, SS, ANSI, #8-
2
32UNCx1/2"
Washer, Helical spring lock, SS, ANSI, #8 2
Description Quantity
Nut, Hex, SS, DIN 934-M10-A2-70 8
Washer, Helical spring lock SS, DIN 127-B10-A2-70 4
Pillar Clamp 1
Hanging Profile 1
Screw, Hex cap, SS, DIN 933-M10x200-A2-70 4
WARNING!
1 Lift the OBN OCB Housing (3) using the lifting eye (5).
2 Tilt the OBN OCB Housing (shown below without the RFU) (3) backwards,
and hook it to the Hanging Profile (4) so that the screw holes are aligned.
3 Fasten two screws (1) and spring washers (2).
4 Hang up to five OBN OCB Housing (3) units (in accordance with the
relevant configuration).
5 Install the RFU (6).
IF Cable
Source
Sharing /
RSL
Waveguide
Waveguide
Ground
Waveguide
Tooth Washer
Nut
Terminal
18.1 1+0
RFU-HP-1R-f or
RFU 1Rx 1
15HPA-1R-RFU-11
OCB with filters 15OCBfx-xxxY-aa-L/H 1
Procedure
1 Mount the termination and short flange on the rear side, as described in
Short Installation on page 17 and Termination Installation on page 18.
2 Mount the OCB to the OCB pole mount, as described in Pole Mount
Preliminary Assembly on page 14.
3 Mount the radio to the OCB, as described in Outdoor Branching Network
(OBM) Housing Hanging Procedure on page 25.
4 Attach the pole mount bracket to the pole, as described in Pole Mount
Preliminary Assembly on page 14.
5 Mount the flexible waveguide and O-ring to the main (upper) port using
the screws and washers supplied with the Flexible Waveguide kit, as
described in Connecting a Flexible Waveguide on page 26.
18.2 1+0 SD
Procedure
1 Mount the termination and short flange on the rear side, as described in
Short Installation on page 17 and Termination Installation on page 18.
2 Mount the OCB to the OCB pole mount, as described in as described in Pole
Mount Preliminary Assembly on page 14.
3 Mount the radio to the OCB, as described in Outdoor Branching Network
(OBM) Housing Hanging Procedure on page 25.
4 Attach the pole mount bracket to the pole, as described in Pole Mount
Preliminary Assembly on page 14.
5 Mount both the flexible waveguide and the O-ring to the MAIN port and
the DIV port using the screws and washers supplied in the Flexible
Waveguide kit, as described in Connecting a Flexible Waveguide on
page 26.
Procedure
2 Mount the OCB to the OCB pole mount, as described in as described in Pole
Mount Preliminary Assembly on page 14.
4 Attach a coupler to the Main OCB Waveguides and secure it with screws.
5 Attach a coupler to the Div OCB Waveguides and secure it with screws.
6 Attach the pole mount bracket to the pole, as described in Pole Mount
Preliminary Assembly on page 14.
RFU-HP-1R-f or
RFU 1Rx 2
15HPA-1R-RFU-11
OCB with filters 15OCBfx-xxxY-aa-L/H 2
Procedure
1 Mount the termination and short flange on the rear side, as described in
Short Installation on page 17 and Termination Installation on page 18.
2 Mount the OCB to the OCB pole mount, as described in Pole Mount
Preliminary Assembly on page 14.
5 Attach the pole mount bracket to the pole, as described in Pole Mount
Preliminary Assembly on page 14.
18.5 2+0 DP
RFU-HP-1R-f or
RFU 1Rx 2
15HPA-1R-RFU-11
OCB with filters 15OCBfx-xxxY-aa-L/H 2
Procedure
1 Mount the termination and short flange on the rear side, as described in
Short Installation on page 17 and Termination Installation on page 18.
2 Mount the OCB to the pole mount, as described in Pole Mount Preliminary
Assembly on page 14.
3 Mount the radio to the OCB, as described in Outdoor Branching Network
(OBM) Housing Hanging Procedure on page 25.
4 Attach the pole mount bracket to the pole, as described in Pole Mount
Preliminary Assembly on page 14.
5 Mount the flexible waveguide and O-ring to the MAIN (upper) port using
the screws and washers supplied in the Flexible Waveguide kit, as
described in Connecting a Flexible Waveguide on page 26.
18.6 2+0 SP
RFU-HP-1R-f or
RFU 1Rx 2
15HPA-1R-RFU-11
OCB with filters 15OCBfx-xxxY-aa-L/H 2
Procedure
1 Mount the OCBs to the OCB pole mount, as described in Pole Mount
Preliminary Assembly on page 14.
2 Slide and tighten both radios to the OCB, as described in Outdoor
Branching Network (OBM) Housing Hanging Procedure on page 25.
3 On the rear side, mount the termination and short to the OCB flanges, as
shown below and as described in Short Installation on page 17 and
Termination Installation on page 18.
4 Mount the S-Bend between the OCBs, as shown below and as described in
Installing S-Bends and the DCB on page 16.
5 Attach the OCB pole mount bracket to the pole, as described in Pole Mount
Preliminary Assembly on page 14.
6 Mount the flexible waveguide and O-ring to the MAIN (upper) port using
the screws and washers supplied in the Flexible Waveguide kit, as
described in Connecting a Flexible Waveguide on page 26.
18.7 2+0 SD SP
Procedure
1 Mount the OCBs to the OCB pole mount, as described in Pole Mount
Preliminary Assembly on page 14.
2 Slide and tighten both radios to the OCB, as described in Outdoor
Branching Network (OBM) Housing Hanging Procedure on page 25.
3 On the rear side, mount the termination flange, as shown below and as
described in Termination Installation on page 18.
4 Mount the S-Bend and DCB to the OCBs, as shown below and as described
in Installing S-Bends and the DCB on page 16.
6 Attach the OCB pole mount bracket to the pole, as described in Pole Mount
Preliminary Assembly on page 14.
7 Mount the flexible waveguide and O-ring to the MAIN (upper) port using
the screws and washers supplied in the Flexible Waveguide kit, as
described in Connecting a Flexible Waveguide on page 26.
18.8 2+0 SD DP
Procedure
1 Mount the termination and short flange on the rear side, as described in
Short Installation on page 17 and Termination Installation on page 18.
2 Mount the OCB to the OCB pole mount, as described in Pole Mount
Preliminary Assembly on page 14.
3 Mount the radio to the OCB, as described in Outdoor Branching Network
(OBM) Housing Hanging Procedure on page 25.
4 Attach the pole mount bracket to the pole, as described in Pole Mount
Preliminary Assembly on page 14.
5 Mount the flexible waveguide and O-ring to the MAIN (upper) port using
the screws and washers supplied in the Flexible Waveguide kit, as
described in Connecting a Flexible Waveguide on page 26.
18.9 2+2 SD SP
Procedure
1 Attach the pole mount bracket to the pole, as described in Pole Mount
Preliminary Assembly on page 14
2 Mount the four OCBs to the pole mount bracket, as described in Pole Mount
Preliminary Assembly on page 14.
3 On the rear side, mount termination plates to the RX ports of the second
and fourth radios using the screws and washers supplied in the
termination kit, as described in Termination Installation on page 18.
5 Mount two S-Bends; the first S-Bend between the EXT port of radio 1 and
the MAIN port of radio 2, and the second S-Bend between the EXT port of
radio 3 and the MAIN port of radio 4. See Installing S-Bends and the DCB on
page 16.
6 Mount two DCBs; the first DCB between the DIV ports of radio 1 and radio
2, and the second between the DIV ports of radio 3 and radio 4. See
Installing S-Bends and the DCB on page 16.
7 Mount two couplers, one to the MAIN port of radio 1 and the other to the
left port of the left DCB, as described in Installing Couplers on page 15.
8 Mount two terminations to the right ports of both DCBs using the screws
and washers supplied with the termination kit, as described in
Termination Installation on page 18.
9 Mount a flexible waveguide with O-ring between the MAIN port in radio 3
and the Coupler port on the top coupler using the screws and washers
supplied with the Flexible Waveguide kit, as described in Connecting a
Flexible Waveguide on page 26.
10 Mount a flexible waveguide with O-ring between the left port in the right
DCB and the Coupler port on the bottom coupler using the screws and
washers supplied with the Flexible Waveguide kit, as described in
Connecting a Flexible Waveguide on page 26.
11 Mount a flexible waveguide with O-ring between the main antenna and the
Antenna port on the top coupler using the screws and washers supplied
with the Flexible Waveguide kit, as described in Connecting a Flexible
Waveguide on page 26.
Procedure
2 Mount the OCB to the OCB pole mount, as described in Pole Mount
Preliminary Assembly on page 14.
4 Attach a coupler to the left two main OCB waveguides and secure it with
screws.
5 Attach a coupler to the left two Div OCB waveguides and secure it with
screws.
6 Attach a coupler to the right two main OCB waveguides and secure it with
screws.
7 Attach a coupler to the right two Div OCB waveguides and secure it with
screws.
8 Attach the pole mount bracket to the pole, as described in Pole Mount
Preliminary Assembly on page 14.
RFU-HP-1R-f or
RFU 1Rx 4
15HPA-1R-RFU-11
OCB with filters 15OCBfx-xxxY-aa-L/H 4
Procedure
2 Mount two of the OCBs to the OCB pole mount bracket, as described in Pole
Mount Preliminary Assembly on page 14.
5 Attach the pole mount bracket to the pole, as described in Pole Mount
Preliminary Assembly on page 14.
7 Attach the pole mount bracket to the pole mount, as described in Pole
Mount Preliminary Assembly on page 14.
RFU-HP-1R-f or
RFU 1Rx 4
15HPA-1R-RFU-11
OCB with filters 15OCBfx-xxxY-aa-L/H 4
Procedure
2 Mount the OCB to the OCB pole mount bracket, as described in Pole Mount
Preliminary Assembly on page 14.
6 Attach the pole mount bracket to the pole mount, as described in Pole
Mount Preliminary Assembly on page 14.
RFU-HP-1R-f or
RFU 1Rx 4
15HPA-1R-RFU-11
OCB with filters 15OCBfx-xxxY-aa-L/H 4
OCB-Sbend OCB-SBend-f 2
1500HP WG Termination, WRccc 15HP-TERM-ccc 2
15HP Short for WRccc 15HP-SHORT-ccc 4
OCB Coupler f GHz OCB-CPLR-f 1
Procedure
1 Attach the pole mount bracket to the pole, as described in Pole Mount
Preliminary Assembly on page 14.
2 Mount the four OCBs to the pole mount bracket, as described in Pole Mount
Preliminary Assembly on page 14.
3 On the rear side, mount termination plates to the EXT ports of the second
and fourth radios using the screws and washers supplied in the
termination kit, as described in Termination Installation on page 18.
4 On the rear side, mount shorts to the DIV ports of all four radios using the
screws and washers supplied in the short kit, as described in Short
Installation on page 17.
6 Mount two S-Bends; the first S-Bend between the EXT port of radio 1 and
the MAIN port of radio 2, and the second S-Bend between the EXT port of
radio 3 and the MAIN port of radio 4. See Installing S-Bends and the DCB on
page 16.
8 Mount a flexible waveguide with O-ring between the MAIN port in radio 3
and the Coupler port on the coupler using the screws and washers
supplied with the Flexible Waveguide kit, as described in Connecting a
Flexible Waveguide on page 26.
9 Mount a flexible waveguide with O-ring between the antenna and the
Antenna port on the coupler, using the screws and washers supplied with
the Flexible Waveguide kit, as described in Connecting a Flexible
Waveguide on page 26.
RFU 2 Rx 15HPA-2R-RFU-f 2
OCB 2Rx with filters 15OCBfx-SD-xxxY-aa-L/H 2
OCB-Sbend OCB-SBend-f 2
DCB Diversity Block fxGHz kit DCBfx 2
1500HP WG Termination, WRccc 15HP-TERM-ccc 2
Flex. WG kit WR-ccc, 4 FT WAVEGUIDE-f-4FT 2
OCB-Pole Mount OCB-Pole Mount 1
Procedure
2 On the rear side, disassemble the termination from the EXT port on
radio 1.
4 On the rear side of the new radios, mount the termination to the EXT port
of the fourth radio using the screws and washers supplied in the
termination kit, as described in Termination Installation on page 18.
5 Mount the two new radios to the OCB, as described in Outdoor Branching
Network (OBM) Housing Hanging Procedure on page 25.
6 Mount two S-Bends; the first S-Bend between the EXT port of radio 1 and
the MAIN port of radio 2, and the second S-Bend between the EXT port of
radio 3 and the MAIN port of radio 4. See Installing S-Bends and the DCB on
page 16.
7 Mount two DCBs; the first DCB between the DIV ports of radio 1 and radio
2, and the second between the DIV ports of radio 3 and radio 4. See
Installing S-Bends and the DCB on page 16.
8 Mount two couplers, one to the MAIN port of radio 1 and the other to the
left port of the left DCB, as described in Installing Couplers on page 15.
9 Mount two terminations to the right ports of both DCBs using the screws
and washers supplied with the termination kit, as described in
Termination Installation on page 18.
10 Mount a flexible waveguide with O-ring between the MAIN port in radio 3
and the Coupler port on the top coupler using the screws and washers
supplied with the Flexible Waveguide kit, as described in Connecting a
Flexible Waveguide on page 26.
11 Mount a flexible waveguide with O-ring between the left port in the right
DCB and the Coupler port on the bottom coupler using the screws and
washers supplied with the Flexible Waveguide kit, as described in
Connecting a Flexible Waveguide on page 26.
12 Mount the flexible waveguide with O-ring between the main antenna and
the Antenna port on the top coupler using the screws and washers
supplied with the Flexible Waveguide kit, as described in Connecting a
Flexible Waveguide on page 26.
RFU-HP-1R-f or
RFU 1Rx 2
15HPA-1R-RFU-11
OCB with filters 15OCBfx-xxxY-aa-L/H 2
OCB-Sbend OCB-SBend-f 2
1500HP WG Termination, WRccc 15HP-TERM-ccc 2
15HP Short for WRccc 15HP-SHORT-ccc 2
Flex. WG kit WR-ccc, 4 FT WAVEGUIDE-f-4FT 1
Procedure
2 On the rear side, disassemble the termination from the EXT port on
radio 1.
4 On the rear side of the two new radios, mount shorts to the DIV ports using
the screws and washers supplied in the short kit, as described in Short
Installation on page 17.
5 On the rear side of the new radios, mount termination plates to the EXT
port of the fourth radio using the screws and washers supplied in the
termination kit, as described in Termination Installation on page 18.
6 Mount the two new radios to the OCB, as described in Outdoor Branching
Network (OBM) Housing Hanging Procedure on page 25.
7 Mount two S-Bends; the first S-Bend between the EXT port of radio 1 and
the MAIN port of radio 2, and the second S-Bend between the EXT port of
radio 3 and the MAIN port of radio 4. See Installing S-Bends and the DCB on
page 16.
9 Mount a flexible waveguide with O-ring between the MAIN port on radio 3
and the Coupler port on the coupler using the screws and washers
supplied with the Flexible Waveguide kit, as described in Connecting a
Flexible Waveguide on page 26.
10 Mount a flexible waveguide with O-ring between the antenna and the
Antenna port on the coupler, using the screws and washers supplied with
the Flexible Waveguide kit, as described in Connecting a Flexible
Waveguide on page 26.
RFU-HP-1R-f or
RFU 1Rx 2
15HPA-1R-RFU-11
OCB with filters 15OCBfx-xxxY-aa-L/H 2
Procedure
2 Disconnect the couplers and the terminations on the first and third OCB.
5 Mount the OCB to the pole mount, as described in Pole Mount Preliminary
Assembly on page 14.
6 Mount a flexible waveguide and O-ring to the MAIN (upper) port of the
OCB and the Coupling port of the coupler using the screws and washers
supplied with the Flexible Waveguide kit, as described in Connecting a
Flexible Waveguide on page 26.
7 Mount a flexible waveguide and O-ring to the antenna port of the coupler
using the screws and washers supplied with the Flexible Waveguide kit, as
described in Connecting a Flexible Waveguide on page 26.
8 On the second OCB pole mount, perform a mounting similar to a 1+1 HSB
configuration, as described in 1+1 HSB on page 39.
Procedure
WG #3
WG #1
WG #2
Coax to WG
2 Remove the coax to waveguide and all three flexible waveguides (both
sides).
3 Remove the S-Bend, four terminations, and marked screws from the DCB.
S-Bend 2
WG #2
Remove 6
screws
WG #3
WG #1
WG #4
OCB
8 Mount three of the OCBs to the OCB pole mount, as described in Pole
Mount Preliminary Assembly on page 14.
10 Attach two S-bend to both left OCBs, as described in Installing S-Bends and
the DCB on page 16.
11 Attach two DCBs to both right OCBs, as described in Installing S-Bends and
the DCB on page 16.
15 Attach the pole mount bracket to the pole mount beneath the 2+2 SD SP
assembly that is already installed, as described in Pole Mount Preliminary
Assembly on page 14.
Already
installed
Upgrade addition
16 Attach flexible waveguide 1 from the Main port of the radio to coupler 1.
Flexible WG #1
Coupler #1
Main Radio
Flexible WG #2
Coupler #2
DCB
18 Mount a flexible waveguide with O-ring between the main antenna and the
Antenna port on the top coupler using the screws and washers supplied
with the Flexible Waveguide kit, as described in Connecting a Flexible
Waveguide on page 26.
Flexible WG to
Main antenna
Coax to WG to
diversity antenna
Procedure
2 Disconnect the couplers and the terminations on the first and third OCB.
3 Mount S-Bends and DCBs to the OCBs, as shown below and as described in
Installing S-Bends and the DCB on page 16.
6 Mount the OCB to the pole mount, as described in Pole Mount Preliminary
Assembly on page 14.
7 Mount a flexible waveguide and O-ring between the MAIN (upper) port of
both OCBs and the coupling port of the upper couplers using the screws
and washers supplied with the Flexible Waveguide kit, as described in
Connecting a Flexible Waveguide on page 26.
8 Mount a flexible waveguide and O-ring to the antenna port of each coupler
using the screws and washers supplied with the Flexible Waveguide kit, as
described in Connecting a Flexible Waveguide on page 26.
9 On the second OCB pole mount, perform a mounting similar to a 1+1 HSB
SD configuration, as described in 1+1 HSB on page 39.
Ceragon Proprietary and Confidential Page 122 of 167
FibeAir® 1500HP/RFU-HP Installation Guide
RFU-HP-1R-f or
RFU 1Rx 2
15HPA-1R-RFU-11
OCB with filters 15OCBfx-xxxY-aa-L/H 2
OCB-Sbend OCB-SBend-f 2
15HP Short for WRccc 15HP-SHORT-ccc 2
OCB-Pole Mount OCB-Pole Mount 1
Procedure
2 Install an additional pole mount bracket on the pole beneath the existing
pole mount bracket, as described in Pole Mount Preliminary Assembly on
page 14.
3 Disconnect the flexible waveguides from the MAIN port on radio 3.
4 Disconnect the terminations from the EXT port on radio 2 and radio 4.
5 Disassemble OCB 3 with radio 3 and OCB 4 with radio 4 from the old pole
mount bracket.
6 Mount OCB 3 with radio 3 and OCB 4 with radio 4 on the new pole mount
bracket, as described in Pole Mount Preliminary Assembly on page 14.
7 For the two radios on the rear side, mount a termination plate to the EXT
ports using the screws and washers supplied in the termination kit, as
described in Termination Installation on page 18.
8 For the two new radios on the rear side, mount a short to the DIV ports
using screws and washers supplied in the short kit, as described in Short
Installation on page 17.
9 Mount one new radio to each pole mount bracket, as described in Outdoor
Branching Network (OBM) Housing Hanging Procedure on page 25.
10 Mount two S-Bends in the top and bottom assemblies; between the EXT
port of radio 2 and the MAIN port of radio 3, as described in Installing S-
Bends and the DCB on page 16.
11 Connect the loose side of the flexible waveguide with O-ring to the MAIN
port on radio 1 in the bottom assembly, as described in Connecting a
Flexible Waveguide on page 26.
RFU-HP-1R-f or
RFU 1Rx 2
15HPA-1R-RFU-11
OCB with filters 15OCBfx-xxxY-aa-L/H 2
Procedure
2 On the OCB pole with two OCBs, disconnect the coupler, add two OCBs, and
slide in two radios.
6 Mount the OCB to the pole mount, as described in Pole Mount Preliminary
Assembly on page 14.
7 Mount a flexible waveguide and O-ring between the MAIN (upper) port of
the OCB and the Coupling port of the coupler using the screws and
washers supplied with the Flexible Waveguide kit, as described in
Connecting a Flexible Waveguide on page 26.
8 Mount a flexible waveguide and O-ring to the antenna port of the coupler
using the screws and washers supplied with the Flexible Waveguide kit, as
described in Connecting a Flexible Waveguide on page 26.
Procedure
2 On the OCB pole with two OCBs, disconnect both couplers, add two OCBs,
and slide in two radios as shown below.
3 Mount S-Bends and DCBs to the OCBs, as shown below and as described in
Installing S-Bends and the DCB on page 16.
6 Mount the OCB to the pole mount, as described in Pole Mount Preliminary
Assembly on page 14.
7 Mount a flexible waveguide and O-ring between the MAIN (upper) port of
both OCBs and the coupling port of the upper couplers using the screws
and washers supplied with the Flexible Waveguide kit, as described in
Connecting a Flexible Waveguide on page 26.
8 Mount a flexible waveguide and O-ring to the antenna port of each coupler
using the screws and washers supplied with the Flexible Waveguide kit, as
described in Connecting a Flexible Waveguide on page 26.
Procedure
4 Tighten the screws between both DCBs and the assembled OCBs.
6 Attach an S-bend between the new OCB and the one close to it. Do this for
both pole mounts.
RFU-HP-1R-f or
RFU 1Rx 2
15HPA-1R-RFU-11
OCB with filters 15OCBfx-xxxY-aa-L/H 2
OCB-Sbend OCB-SBend-f 2
15HP Short for WRccc 15HP-SHORT-ccc 2
Procedure
2 Disconnect the terminations from the EXT port on radio 3 in the bottom
and top assemblies.
3 For the two new radios on the rear side, mount terminations to the EXT
ports using screws and washers supplied in the termination kit, as
described in Termination Installation on page 18.
4 For the two new radios on the rear side, mount shorts to the DIV ports
using screws and washers supplied in short kit, as described in Short
Installation on page 17.
5 Mount one new radio to each pole mount bracket, as described in Outdoor
Branching Network (OBM) Housing Hanging Procedure on page 25.
6 Mount two S-Bends in the top and bottom assemblies between the EXT
port of radio 3 and the MAIN port of radio 4, as described in Installing S-
Bends and the DCB on page 16.
Configuration OCB DCB U-bend S-bend Coupler 3dB Coupler Term. Cover/Short Pole Mount
1+1 HSB 2 0 0 0 1 0 2 2 1
1+1 HSB SD 2 0 0 0 2 0 2 0 1
2+2 XPIC HSB 4 0 0 0 2 0 4 4 1
2+2 XPIC HSB SD 4 0 0 0 4 0 4 0 4
3+1/4+0 4+1/5+0
3+1/4+0 SD 4+1/5+0 SD
4+1 XPIC
9+1 XPIC SD
1+0 IP-10
21.1.2 Assembly
1 Insert the termination gaskets in their places on the OCB 19” Rack Adapter
(MK-3230-0), and fasten the Termination Plates to the Adapter using 16
screws (4 in the table above) and 16 washers (3), as shown in the
following illustration.
2 Fasten the left bracket to the OCB 19” Rack Adapter (MK-3230-0) using 8
screws (number 2 in the table above) 8 washers (3), and another 8
washers (1), as shown in the following illustration.
The following illustrations show the New OCB assembled with the 19” Rack
Adapter.
21.2.2 Assembly
1 Insert the termination gaskets in their places on the OCB 19” Rack Adapter
(MK-3230-0), and fasten the Termination Plates to the Adapter using 24
screws (4 in the table above) and 24 washers (3), as shown in the
following illustration.
2 Fasten the left bracket to the OCB 19” Rack Adapter (MK-3230-0) using 8
screws (number 2 in the table above) 8 washers (3), and another 8
washers (1), as shown in the following illustration.
The following illustrations show the New OCB assembled with the 19” Rack
Adapter.
21.3.2 Assembly
1 Insert the termination gaskets in their places on the OCB 19” Rack Adapter
(MK-3230-0), and fasten the Termination Plates to the Adapter using 24
screws (4 in the table above) and 24 washers (3), as shown in the
following illustration.
2 Fasten the left bracket to the OCB 19” Rack Adapter (MK-3230-0) using 8
screws (number 2 in the table above) 8 washers (3), and another 8
washers (1), as shown in the following illustration.
4 Fasten the HSB Coupler to the New OCB 19” Rack Adapter Main Terminals
using 10 screws (number 4 in the table above), and 10 washers (5), as
shown in the following illustration.
The following illustrations show the New OCB assembled with the 19” Rack
Adapter.
Term.
RX
Short
RX
1+0 SD SP
OCB kit
RFU
TX Antenna
Term.
RX
Antenna
RX
Div.
2+0 DP
OCB kit
RFU
Antenna
TX
V
Term.
RX
Short
RX
OCB kit
RFU
Antenna
TX
H
Term.
RX
Short
RX
2+0 SD DP
OCB kit
RFU
Antenna
TX
Main V
Term.
RX
Antenna
RX
Div. V
OCB kit
RFU
Antenna
TX
Main H
Term.
RX
Antenna
RX
Div. H
2+0 SP
OCB kit
RFU
TX Antenna
RX
S-Bend WG
Short
RX
OCB kit
RFU
TX Term.
RX
Short
RX
2+0 SD SP
OCB kit
RFU
Antenna
TX
Main
RX
S-Bend WG
RX
OCB kit
RFU
TX Antenna
Div.
DCB
Term.
RX
Term.
RX
1+1 HSB SP
OCB kit
RFU
TX Antenna
Term.
RX Coupler
Short
RX
OCB kit
RFU
TX
Term.
RX
Short
RX
Coupler
Term.
RX
Antenna
RX
Div.
OCB kit
RFU
Coupler
TX
Term.
RX
RX
Coupler
S-Bend WG
RX
OCB kit
RFU
TX
Antenna
Div.
Term.
RX
DCB
Term.
RX Coupler
OCB kit
RFU
G
xW
TX Fle
RX
S-Bend WG
RX
Flex WG
OCB kit
RFU
TX
Term.
RX
DCB
Term.
RX
2+2 HSB SP
OCB kit
RFU
TX Antenna
RX
Coupler
S-Bend WG
Short
RX
OCB kit
RFU
TX
Term.
RX
Short
RX
Flex WG
OCB kit
RFU
TX
RX
S-Bend WG
Short
RX
OCB kit
RFU
TX
Term.
RX
Short
RX
Installations Upgrades
Following are the Installations Upgrades configurations:
1. From 1+1 HSB
to
2+2 HSB SP
to
3+3 HSB SP
to
4+4 HSB SP
From 1+1 SD SP
to
2+2 SD DP
to
3+3 SD DP
to
4+4 SD DP
1+1 HSB SP 2+2 HSB SP 3+3 HSB SP 4+4 HSB SP
RX
Term.
RX RX RX
Reused RFU/ BN
Reused RFU/ BN
Coupler
Coupler
Coupler
S-Bend WG
Coupler
Added Acc.:
S-Bend WG
S-Bend WG
Short
RX
Short
Short
RX
Short
RX RX
2x S-Bend WG
1x Flex WG
OCB kit OCB kit OCB kit
OCB kit RFU
Reused RFU/ BN
Existing Pole Mount
RFU RFU RFU
TX TX
TX TX
RX
Term.
Term.
RX RX RX
S-Bend WG
Short
RX
Short
RX
Short
Short
RX RX
Flex WG
OCB kit OCB kit OCB kit
RFU
Added RFU/ BN
RFU RFU
Flex WG
TX
TX TX
Flex WG
RX
Term.
RX RX
Added RFU/ BN
S-Bend WG
Short
S-Bend WG
RX
Short
Short
RX RX
OCB kit
OCB kit RFU
Added RFU/ BN
RFU
OCB kit Added Acc.: TX
TX RFU
1x Pole Mount kit
TX 2x S-Bend WG
Term.
RX
Term.
RX
RX
Short
RX
Reused RFU/ BN
Short
RX
S-Bend WG
Short
RX
RX
RX
S-Bend WG
Short
RX
S-Bend WG
Short
RX
OCB kit
RFU
Reused RFU/ BN
OCB kit
RFU
Added RFU/ BN
TX
TX
S-Bend WG
Short
RX
Short
RX
OCB kit
RFU
TX
RX
S-Bend WG
Short
RX
OCB kit
RFU
Added RFU/ BN
TX
Term.
RX
Short
RX
RX RX RX
Coupler
Coupler
Coupler
No Change
Added Acc.:
S-Bend WG
S-Bend WG
Short
RX
Short
Short
RX RX
2x S-Bend WG
1x Flex WG
OCB kit OCB kit OCB kit
RFU RFU RFU
TX TX TX
Reused RFU/ BN
Term.
Term.
Term.
RX RX RX
No Change
Existing Pole Mount
Short
Short
RX RX RX
Flex WG
Flex WG
OCB kit
RFU OCB kit OCB kit
Antenna RFU RFU
TX
H TX TX
Term.
RX
RX RX
Added RFU/ BN
Coupler
Short
RX
S-Bend WG
S-Bend WG
Short
Short
RX RX
RX
Term.
Term.
RX RX
Short
RX
Short
Short
RX RX
RX RX
Additional Pole Mount
Reused RFU/ BN
Added RFU/ BN
Coupler
Coupler
S-Bend WG
Short
Short
RX RX
Term.
Term.
RX
RX
Short
RX
Flex WG
OCB kit
RFU
TX
RX
S-Bend WG
Added Acc.:
Short
RX
Added
1x S-Bend WG
1x Flex WG
OCB kit
RFU
TX
Term.
RX
Short
RX
1+1 SD SP 2+2 SD SP 3+3 SD SP 4+4 SD SP
OCB kit OCB kit OCB kit
OCB kit RFU RFU RFU
RFU Antenna Antenna Antenna
Antenna TX TX TX
TX Main Main Main
Main
Coupler
RX RX RX
Term.
RX
Coupler
Coupler
Reused RFUs
Coupler
S-Bend WG
S-Bend WG
S-Bend WG
RX RX RX
Antenna
RX
Div.
OCB kit OCB kit OCB kit
OCB kit RFU RFU RFU
Reused RFUs
TX TX
Coupler
TX
Antenna Antenna Antenna
DCB
DCB
RX
DCB
Term.
RX
S-Bend WG
S-Bend WG
Term.
RX RX RX
Coupler
Coupler
Coupler
Reused RFUs
RX
U-Bend WG
U-Bend WG
OCB kit OCB kit OCB kit
RFU RFU RFU
G
xW
Fle
TX TX TX
Term.
RX Added Acc.: RX RX
2x S-Bend WG
S-Bend WG
S-Bend WG
Added RFUs
RX 2x DCB RX RX
Flex WG
1x Coupler
DCB
DCB
1x Flex WG
OCB kit Added Acc.: OCB kit
RFU Short Term.
2x S-Bend WG RFU Term.
TX 2x DCB TX
Added RFU
OCB kit
Gs
RFU 2x U-Bend
W
Term.
x
RX
Term.
DCB
Gs
RX
Fle
TX
Flex W
Term.
RX RX
RX
S-Bend WG
RX
OCB kit
RFU
S-Bend WG
RX
DCB
RX
S-Bend WG
RX
OCB kit
Added RFUs
RFU
U-Bend WG
OCB kit TX
Reused RFUs
RFU
DCB
S-Bend WG
Term.
RX RX
RX
OCB kit
U-Bend WG
RFU
DCB
TX
Short Term.
RX
S-Bend WG
RX
DCB
OCB kit
RFU Term.
TX
Added RFU
Term.
RX
RX
RX RX
Term.
RX
Coupler
Coupler
S-Bend WG
S-Bend WG
Antenna RX RX
NO Change
RX
Div. V
OCB kit OCB kit
OCB kit RFU RFU
RFU
Coupler
TX TX
TX Antenna Antenna
Term.
RX
DCB
RX
DCB
Reused RFU/ BN
Term.
RX
No Change
Term. Term.
RX RX
Existing Pole Mount
Coupler
Coupler
RX
2x S-Bend WG
S-Bend WG
S-Bend WG
Term.
RX RX RX
Flex WG
Flex WG
2x DCB
Added RFU/ BN
Antenna 1x Flex WG
RX
Div. H OCB kit (Non use: 2x Couplers) OCB kit
RFU RFU
OCB kit TX TX
RFU
Coupler
Term.
TX
Term.
RX
DCB
RX
DCB
Term.
Term.
RX RX RX
Term.
RX
OCB kit
OCB kit RFU
RFU Antenna
Antenna TX
Main H
TX
Main H
(requires whenever RFU>5)
Coupler
RX
Additional Pole Mount
Reused RFU/ BN
Term.
RX
Coupler
S-Bend WG
Added RFU/ BN
Antenna RX
RX
Div. H
OCB kit
OCB kit RFU
RFU
Coupler
TX
TX Antenna
RX
DCB
Term.
RX
Term.
RX
Coupler
RX
OCB kit
RFU
x WG
TX Fle
RX
Added Acc.:
Added RFU/ BN
2x S-Bend WG
S-Bend WG
RX
Flex WG
2x DCB
1x Flex WG
OCB kit (Non use: 2x Couplers)
RFU
TX
Term.
RX
DCB
Term.
RX