Professional Documents
Culture Documents
*customer choice
Standard Coach building Specification
1.0 Mid Area of vehicle (Operator Area)
1.1 Three 19” rack bays across width of vehicle with full width desk across bays.
-Two 19" rack bays with 6U rack space each between wheel housings.
-Two 19" rack bays with 3U rack space each above main rack.
#Photos1,2
Actual amount of rackspace depends on vehicle type, size and clients demands. Shown is a Sprinter
racklayout with long wheelbase, high roof height.
1.3 Walls and ceiling will be covered with carpet (with antistatic and fire-resistant properties).
1.4 Floor covering anti-slip PVC coating (with antistatic properties). With floor heating elements
under covering.
Carpet used for wall lining.
#Photo 3
#Photo 4
#Photo 5
1.0 Mid Area of vehicle (Operator Area)
1.7 Platform with storage place for tripods (optional, available only with vehicles with GVW at least
5000 kg ).
#Photos 6,7
2.0 Rear Area of Vehicle
- A cable hook to strap the cables entering the vehicle, reducing cable stress.
#Photo 8
Cable entry cut-out on the right hand side of the rear door.
Above the cut-out is the cable loop to manage cables entering the vehicle.
Below the cut-out is the cable hook to fasten cables entering the vehicle.
2.0 Rear Area of Vehicle
- One powerful radial fan on the top of main racks extracting hot air from racks.
- Two stainless steel air outlets with back draft shutters in each side of the vehicle for air
circulation.
2.7 Fit full width mid level shelf for cables, etc.
See #Photo 4
- Heavy-duty manual jacks that are operated by a crank handle (or heavy-duty electrical jacks
with or without auto-levelling function).
#Photo 9
3.0 External works on Vehicle.
- Vehicle immobility switches to prevent that the vehicle can be driven with the jacks folded
down.
3.4 Prepare roof for mounting antenna system and cable entry box.
- Manually (or with motor kit) extractable awning, 3.7m, colour white, fabric colour blue waves.
- Manually (or with motor kit) extractable awning, 1.4m, colour white, fabric colour blue waves.
#Photo 10
3.6 Mount railing on both side of vehicle roof, inc telescopic ladder.
4.0 Miscellaneous
AC system includes voltage and current meters plus ‘external/generator’ changeover switch
with single input RCCB, 10 off MCBs and RCBO for external output.
- Complete AC system built in a power module box, fitted in rear areas sub frame.
- DC system would provide LED indication of presence and distribution via individual fuses for
up to 3 outlets and an overall switch.
7.1 Three-phase 230V mains input panel in rear of truck with 16A(32A) input, 16A auxiliary output
(on request). - Mains “live” indicator.
8.0 Heating
Autonomic diesel heater with installation ( type Hydronic Webasto) with engine heating
(optional).
#Photo 11
1.0.2 Swivel under-carriage can be mounted on to driver and passenger seat with a flap table in front
of one seat. The cabin back wall will then be removed.
#Photo 12
- To be used as e.g laptop edit table when the driver seat is turned around.
3.0.2 Supply manual or electrical powered jacks (x4) below vehicle floor.
- Heavy-duty manual or electrical powered heavy-duty electrical jacks with or without auto-
levelling function
3.0.3 Mount RF-antennas on the vehicle roof with cabling to the racks.
4.0.1 Miscellaneous
4.0.2 Roof mounted 10950 Btu (3.95 KW) air conditioner unit with built-in heater.
Roof mounted 13500 Btu (3.15 KW) air conditioner unit with built-in heater.
- Air suspension for rear axle with automatic pressure control, set of 2.
8.1 Power Generator
- Fischer Panda 8.000 NE PVMV-N, 8,1 kVA, 3000rpm or 1500rpm generator with water-
cooled Kubota engine.
-Includes VCS system, 4DS capsule, remote control panel, electrical generator looms, fuel
pump, fine fuel filter, roof (or under floor) mounted radiator cooling system complete with
cowling and expansion tank and full instruction manual.
8.2 Install generator in rear area and connect it to main fuel supply.
8.3 Install generator radiator on roof (or under floor) and run cooling fluid tubes.
#Photos
Generator radiator mounted at the 13,14
rear of the vehicle. Antenna sub-
frame and 2 AC units on the vehicle
roof.
The one of the AC units is
completely hidden inside the antenna
pod.
#Photo 15
#Photo 16
#Photo 17
Out-let and control panel for the AC unit that is mounted
inside the pod.
#Photo 18
Vehicle layout