Professional Documents
Culture Documents
不饱和聚酯腻子的稳定性研究
不饱和聚酯腻子的稳定性研究
不饱和聚酯腻子的稳定性研究
王 琼 陈国华 ( 华侨大学化工学院, 泉州 362011)
摘要: 以不饱和聚酯树脂为主要原料的原子灰配方中各种防沉剂的选择、用量及效果, 探讨
原子灰在储存期中防沉降的最佳条件。
关键词: 不饱和聚酯; 腻子; 稳定性
1 前言
不饱和聚酯腻子是用于汽车、高档家具等涂装 2 2 2 工艺过程
的新型材料, 替代了以前所使用的石膏浆、桐油灰 首先, 采用母料法添加 S iO 2 气溶胶, 取 100
等产品。它具有使用方便、固化时间短、打磨松度 份树脂加入 8 份 S iO 2 于高 速搅 拌器中 搅拌 3~
好、表面光洁度高、附着力强等优点, 受到用户的 5m in, 制得母料转入慢 速搅拌器内, 分批加入混
普遍欢迎。 匀过筛的主填料滑石粉, 钛白粉及其它助剂。
目前国产原子灰其产品多项性能均可与进口产 2 3 防沉效果的测试
品 ( 以日本 gg g! 牌原子灰为参照) 相媲美, 但 将 4kg 产 品 装 入密 封 镀 锌 铁 桶 内, 存 放 于
国产产品贮存期短。如一般进口产品贮存有效期为 25 ∀ ~ 28 ∀ 下测试实际的贮存期。其时间以树脂与
12 个月, 而国产同类产品的贮存期往往只有 6 个 填料不分层或分层后通过人工轻微搅拌可再分散为
月左右。影响原子灰贮存期的主要因素除了表面结 产品的贮存有效期。
皮以及树脂本身有效期之外, 最主要的原因就是填 3 结果与讨论
料的沉降问题。本文主要研究防沉剂及其用量、填 3 1 防沉剂的防沉效果
料粒度等对腻子沉降的影响。 表 2 为用不同防沉剂制备腻子的贮存情况, 从
2 实验部分 中可以看出, 对于母体为不饱和聚酯腻子来说, 由
2 1 材料与试剂 于其产品的填料加入量大, 要使填料在长时间内不
337# 不饱和聚酯树脂、轻质氧化镁、聚乙烯 发生沉降, 又不影响腻子其它产品性能, 经过反复
蜡、聚甲基丙烯酸甲酯、气相 S iO 2 、滑石粉等。 试验得出, 在 4kg 腻子中加入 32g 气相 S iO2 为最
2 2 不饱和聚酯腻子的制备 佳, 其添加工艺采用母料法为佳。
2 2 1 腻子配方见表 1 3 1 1 轻质 M gO[ 1]
表1 腻 子 配 方 碱土金属的轻质 M gO 对基料为不饱和聚酯树
原料名称 质量分数/ % 脂的腻子有流变作用。它的流变作用可防止贮存时
337# 不饱和聚酯树脂 100 填料的沉降或使沉淀软化, 以提高其再分散性。如
滑石粉 ( 100 目) 50
滑石粉 ( 200 目) 50 在 4kg 腻子中加入 ( 3~ 5) 份轻质 MgO 作为流变
滑石粉 ( 320 目) 100 助剂, 结果在短期内 ( 2~ 3 个月贮存期内) 防沉
气 相 S iO2 8 效果较好。但由此引入的疏松 网络结构! 比较脆
钛白粉 5
环烷酸钴 3 弱, 轻微的外力, 如机械外力即可破坏这个网络而
其它助剂 若干 失去流变防沉作用, 同时增加了腻子的粘度, 使操
#中 国 涂 料# 31 #2001 年第 3 期#
技术园地
#中 国 涂 料# 32 #2001 年第 3 期#
Li Guan zhong ( 24) iron oxide
T he features of t he new mode of service in sell Wang Zhi ping and others ( 36)
ing arch coatings are expertness, personalit y, int er T w o preparat ion methods are introduced. Some
nat ionality and do it through the net. f act ors w hich w ill influence the rat e of react ion are in
vest ig at ed. By adjust ing t hese factors, one may ob
The use of extrusion technology in the modifi t ain high performance ex tra fine yellow iron oxide
cation of polyolefine w it h even part icle size.
L i Gui dong; Zhang Ju sheng ( 26)
A descript ion of the met hod. The development of world coatings technology
in the new century
Air dry acrylic polyurethane hammer finishes Z hao Jin bang ( 40)
Chen Jiao ying and ot hers ( 29) T he aut hor makes an overall predict ion on t he
St eps of it s preparat ion; formulation; f ilm per progress of the w orld coat ings industry. T he develop
f orm ances are described. F act ors w hich w ill inf luence ments in major areas: w at er based coatings, high sol
the hammer eff ect are discussed. id coatings, solvent free coat ings, pow der coatings,
radiat ion cure coat ings, nanometric technology,
Investigation on the stability of the unsaturat blending polymers and int er penet rat ing polymer net
ed polyester putty work are f orecast ed. T he sit uation of t he coat ings raw
Wang Qiong; Chen Guo hua ( 31) materials, including pig ments, solvent s and addit ives
T he selection of adequate anti sett ling agent for a are discussed.
polyester put ty and its ef fect on t he set tling propert y
are discussed. World coatings associations and the industries
they depend
Investigation on the use of nanometric materi Yun hua ( 45)
als in coatings A serial report .
Zhou Shu xue; Wu L i min ( 33)
Variet ies, applicat ions, methods of preparation The technical requirements of container coat
and some preliminary research result s are introduced. ings
Recommendat ion is m ade for t he development of so Li M in feng ( 47)
called nanomet ric coatings. T he performat nces, testing met hods and qualit y
requirement s are introduced.
Preparation of extra micro transparent yellow
China Paint
Sponsor: China National Coatings Industry Association
Editor: T he Editorial Office of %China Paint&
Address: NO 1, L iu Pu Kang Street, Beijing, China
Post Code: 100011 T el: ( 010) 82011917 Fax : ( 010) 62376292
International Standadization Number: ISSN 1006- 2556
China Publisher Number: CN 11- 3544/ T Q
Distribut ion Number Abroad: 4553 BM