Professional Documents
Culture Documents
Revision 10/13/20
2004-’09
Toyota Prius
IMPORTANT
Before starting, compare items on your invoice with items received.
Carefully check through packaging material. If any item is missing,
please call Crutchfield Technical Support at 1-800-955-9094.
Inside...
Although reasonable attempts are made to verify the accuracy of the information contained in this MasterSheet, it is presented without
warranties or guarantees of any type due to the constantly changing nature of this type of information and running changes in vehicle
production. Any person or entity using this information does so at his or its own risk. If you find our instructions are different from your
vehicle, or if you have questions, do not continue with your installation. Contact our toll-free technical support for assistance.
*0000530185*
Page
5 Receiver Installation
6 Center Dash Speaker
7-8 Front Door Speakers
9-10 Rear Door Speakers
11 Wire Splicing Guide
Phillips Small Flat Blade 10mm Socket, Panel Tool 11/64” 1/8” Soldering Iron Wire Strippers
Screwdriver Screwdriver Ratchet & & Solder & Crimp Caps
Extension Drill & Bits
Tools Required
FIGURE 5 FIGURE 6
1-800-955-9094
TECHNICAL SUPPORT
8. Remove two (2) Phillips screws (one on each Air Vent Trimpanel Pocket/Trim
side) securing pocket/trim. Pull out trim to (left of radio)
release clips and remove (Figure 9).
FIGURE 7
1-800-955-9094
TECHNICAL SUPPORT Copyright 2020 Crutchfield Corporation 3
053 0185
OEM Integration
This page addresses integrating aftermarket
accessories such as Bluetooth Adaptors,
R
1-800-955-9094
TECHNICAL SUPPORT Copyright 2020 Crutchfield Corporation 4
053 0185 NOTES:
Please read first
• Check to make sure the Crutchfield receiver wiring
Receiver Installation adaptor plugs into the vehicle receiver harness.
If the Crutchfield adaptor is incorrect, please call our
Technical Support Department at 1-800-955-9094.
! IMPORTANT
In most cases, the resistor included with the dash kit for this vehicle must be
soldered between two wires in the vehicle’s receiver harness in order to retain
climate controls. It will also retain navigation if equipped. See dash kit for
wiring details. Note: If using the PAC RP4.2-TY11 wiring interface, soldering
the resistor to the vehicle harness is not necessary.
RCA cables
climate control harnesses
airbag harnesses
power outlet harnesses
other accessory devices
FIGURE 2
1-800-955-9094
TECHNICAL SUPPORT Copyright 2020 Crutchfield Corporation 6
053 0185 NOTES:
Please read first
Front Door Speakers • Instructions show factory size speakers or speakers
with adaptor brackets only. Cutting or fabrication (not
shown) will be required for other speaker sizes.
! IMPORTANT
No speaker wiring adaptor is available at this time from
Crutchfield for the tweeter location. It will be necessary to FIGURE 1 FIGURE 2
splice wires in order to install an aftermarket speaker.
FIGURE 6
1-800-955-9094
TECHNICAL SUPPORT Copyright 2020 Crutchfield Corporation 7
053 0185
! IMPORTANT
No speaker wiring adaptor is available at this time from
Crutchfield for the tweeter location. It will be necessary to FIGURE 1 FIGURE 2
splice wires in order to install an aftermarket speaker.
Screw Cover
1. Pry out screw cover behind door release and
remove one (1) Phillips screw (Figure 1).
1-800-955-9094
TECHNICAL SUPPORT
FIGURE 4
! CAUTION:
Always be careful when drilling or cutting in a vehicle. WEAR
EYE PROTECTION. Be aware of things such as wiring,
windows, fuel lines and safety devices. Check depth and
location to avoid damage to vehicle appearance.
! SAFETY CHECK
1-800-955-9094 Check that wires do not interfere with window operation.
Test door lock and release operation.
TECHNICAL SUPPORT Copyright 2020 Crutchfield Corporation 10
053 0185
Wire Splicing Guide These methods can be used to make wiring connections if no receiver or speaker wiring adaptor is available.
Wire color information (if available) can be found on the next page.
Factory harness is removed. Save New speaker wires are spliced into
CRIMP METHOD harness if it is to be reconnected in
the future by this method.
SOLDER METHOD factory wires behind harness.
1. Cut factory wires behind 2. Strip end of each 1. Carefully strip out a 1/2” 2. Twist wires from new
factory speaker harness. wire back 1/2”. section on each factory speaker to stripped
speaker wire behind the sections of factory wires
factory speaker harness. as shown making sure
polarity is correct.
Factory Wires
---
-- - ------
Negative Wires
Strip Out 1/2” New Wires
+
+
+ + + + + + + + + + + + +
Positive Wires
3. Twist each positive pair of 4. Squeeze middle of cap 3. Heat wires first with 4. Wrap wiring connections
wires together and insert for tight connection. soldering iron, then with electrical tape.
in crimp cap. Repeat touch solder to
step for negative wires. 5. Connect new wires to wires for solid 5. Connect new wires to
speaker with spade connections. speaker with spade
First
connectors. connectors.
Factory Wire ---
-- - --------
Last
+
+
+ + + + + + + + + + + + + + + + + + + + +
1-800-955-9094
TECHNICAL SUPPORT Copyright 2020 Crutchfield Corporation 11
053 0185
Wire Splicing Guide (continued) NOTE: In most cases a speaker wiring adaptor is available from Crutchfield and splicing will
not be necessary. If no adaptor is available, use this chart as a guide to match and splice wires.
Function Polarity/Color/Location
Left front door tweeter positive (+): pink, negative (-): violet
Right front door tweeter positive (+): light green, negative (-): blue
Left front door speaker/woofer positive (+): pink, red or yellow, negative (-): violet or black
Right front door speaker/woofer positive (+): light green, negative (-): blue
Center dash speaker positive (+): red, negative (-): white
Left rear door speakers positive (+): black or red, negative (-): yellow or black
Right rear door speakers positive (+): red, negative (-): white
Vehicle speed sense¹ pin #25 of 26-pin plug at multi-display unit - violet
Reverse (+)¹ pin #6 of 11-pin plug located low in the driver’s side kick panel - red
Parking brake¹ at parking brake switch - red
Foot brake¹ at foot brake switch or pin #5 of 11-pin plug located low in the driver’s side kick panel - blue
NOTES:
• If equipped with a factory amplifier, the amplifier will be located under the front passenger’s seat.
• ¹These wires and functions may also be generated by the OEM integration interface used when replacing the radio.
1-800-955-9094
TECHNICAL SUPPORT Copyright 2020 Crutchfield Corporation 12