SECTION
METROLOGY 8 ENGINEERING SERVICES Excellence, it's Our Promise
CERTIFICAT D'ETALONNAGE
CALIBRATION CERTIFICATE,
N° E06-05-1/20
Délivréa: CERI
Issued to: ZI La Charguia- Rue 8600 N°82-Tunis, Tunisie
Equipement étalonné
Calibrated instrament
Désignation : WELDING MACHINE
Designation
Construeteur: — LINCOLIN type: Invertec 270SX
‘Manufacturer : type:
N° de série: P1191001311 Identification : Inexistant
Serial Number : identification :
Date d’émission : 11/02/2020
Date of issue :
Ce certificat comprend (03) pages
This certificate include (03) pages
PRESIDENT DIRECTEUR GENERAL
(CHIEF EXECUTIVE OFFICER
SMADHI MoHaM
La reproduction de oe curtifiat et autorsde que sous Ia forme de fasimilé phologrphigue tral
‘This Cerificate ray not be reproduced the han in fal by photographie roots
Lot 34 Zone Industrielle Zriba 4, 1152 Zaghouan— Tunisie
‘+ RLC : BO6214252012, Tél: +216 72 668 421, Fax: +216 72 668 431
site : www.protimess.com, Email: protimessa@)protimess.comCALIBRATION CERTIFICATE N° EO6-05-1 /20
Résolution 1A
Resolution
Alfichage: Numérique
Display:
Remarques
Notes
NIA
‘Calibration condition
Température 182°C Date d’étalonnage ; 11/02/2020
Temperature Date of calibration
Humidité 5025 %RH Réalisé par: B.Wajik
Humidity ‘Operator
Liew Site client
Place of calibration
Mode opératoire
Operating procedure
L’étalonnage a été effectué par comparaison directe des indications de I'instrument soumis 4 I’étalonnage avec un
étalon référencé ci-dessous, les deux placées dans le méme milieu de comparaison. L'étalonnage a été effectué en
trois points répartis sur toute I’étendue de mesure.
The calibration was performed by direst comparison of instrument indications under test with a standard referenced below,
both placed in the same comparison environment. Calibration was performed at three temperature points.
Référentiels utilisées
‘Used references,
DCT-PREV-E 10 Procedure of electrical calibration
LAB GTA 10 Technical guide for accreditation
Etalons utilisées
Reference equipments used
‘Désignation | Marque ‘Modéle NE Certificat
Designation Brand mode! Cetificate N*
Ampermetric clamp FLUKE 376 27420200WS.
Page 2/3
PROTIMESS sa, Lot 34 Zone Industrielle Zriba 4, 1152- Zaghouan — Tunisie
(MF :1273205i/A/M/000 , R.C : BO6214252012, Tél: +216 72 668 421, Fax: +216 72 668.431,
site : www-protimess.com, Email: protimess“@protimess.comCALIBRATION CERTIFICATE N° EO6-05-1/20,
Tragabilité
L*étalonnage a été réalisé avee des étalons raccordés A la chaine (inter)nationale
‘The calibration has been executed by instruments that are traceable to (inter)national standards
Incertitude
‘Uncertainty,
‘Les incertitudes élargies mentionnées sont celles correspondant a deux incertitudes-types. Les incertitudes sont calculées en
tenant compte des différentes composantes d'incertitudes, étalons de référence, moyen d’étalonnage, conditions
environnement, contribution de ’instrument étalonné, répétabilité
The reported expanded uncertainties is determined by a coverage factor K=2 providing a level of confidence of approximately
98%. The uncertainties are calculated taking into account the different components of uncertainties, reference standards,
calibration means, environmental conditions, contribution of the calibrated instrument, repeatability,
Résultats de ’étalonnage
Calibration Results
Valeur indiqué par ‘Valeur mesuré Erreur Tneertitude dlargie
instrument par I’éalon Expanded
uncertainty (K=2)
a) ) w a)
76 72 12
4s
tor 101,9 09
164 1663 23
Fin de Certificat
n — Endof Certificate ce
Page 3/3
PROTIMESS sa, Lot 34—Zone Industrielle Zriba 4, 1152 Zaghouan — Tunisie
[MF :12732081/A/M/000 , R.C : BO6214252012, Tél: +216 72 668 421, Fax: +216 72 668 431
site | www.protimess.com, Email : protimess@)protimess.com