Professional Documents
Culture Documents
30, 2005
Model No.: N150P5 -L02
Approval
- CONTENTS -
REVISION HISTORY ------------------------------------------------------- 3
8. PRECAUTIONS ------------------------------------------------------- 22
8.1 HANDLING PRECAUTIONS
8.2 STORAGE PRECAUTIONS
8.3 OPERATION PRECAUTIONS
9. PACKING ------------------------------------------------------- 23
9.1 CARTON
9.2 PALLET
2 / 25
Version 2.1
Issued Date: Jun. 30, 2005
Model No.: N150P5 -L02
Approval
REVISION HISTORY
Page
Version Date Section Description
(New)
Ver 1.0 Mar. 14. ‘05 All All Preliminary specification first issued.
Ver 2.0 Jun. 06. ‘05 7 3.1 Update Electrical Characteristics Table 3.1 TFT LCD Module
8 3.2 Update Electrical Characteristics Table 3.2 Backlight Unit
14 5.5 EDID code update
17 6.1 Modify Input Signal Timing Specifications and Timing Diagram
19 7.2 Modify Optical Specification
Average Luminance spec from min.190 typ.220 to min.180 typ.210
Viewing Angle θY+ spec from min10 / typ15 to min15 / typ20
Viewing Angle θY- spec from min30 / typ35 to min40 / typ45
Ver 2.1 Jun. 30. ‘05 19 7.2 Average Luminance spec change from min.180 typ.210 to min.170
typ.200
3 / 25
Version 2.1
Issued Date: Jun. 30, 2005
Model No.: N150P5 -L02
Approval
1. GENERAL DESCRIPTION
1.1 OVERVIEW
N150P5 is a 15.0” TFT Liquid Crystal Display module with single CCFL Backlight unit and 30 pins LVDS
interface. This module supports 1400x 1050 SXGA+ mode and can display 262,144 colors. The optimum
viewing angle is at 6 o’clock direction. The inverter module for Backlight is not built in.
1.2 FEATURES
- Thin and light weight
- SXGA+ (1400 x 1050 pixels) resolution
- DE (Data Enable) only mode
- 2 channel 3.3V LVDS (Low Voltage Differential Signaling) interface
- Support EDID Structure Version 1 Revision 3
1.3 APPLICATION
- TFT LCD Notebook
+/- 0.5mm
4 / 25
Version 2.1
Issued Date: Jun. 30, 2005
Model No.: N150P5 -L02
Approval
100
90
80
60
Operating Range
40
20
5 Storage Range
-40 -20 0 20 40 60 80
Temperature (ºC)
Note (2) The temperature of panel surface should be 0 ºC Min. and 50 ºC Max.
Note (3) Condition for 220/2 G/ms is Half Sine Wave.
Note (4) 10 ~ 500 Hz, 0.5 Hr / Cycle, 1 cycles for each X, Y, Z. The fixing condition is shown as below:
Gap=2mm Bracket
Note (5) At testing Vibration and Shock, the fixture in holding the module has to be hard and rigid enough
so that the module would not be twisted or bent by the fixture.
5 / 25
Version 2.1
Issued Date: Jun. 30, 2005
Model No.: N150P5 -L02
Approval
6 / 25
Version 2.1
Issued Date: Jun. 30, 2005
Model No.: N150P5 -L02
Approval
3. ELECTRICAL CHARACTERISTICS
3.1 TFT LCD MODULE Ta = 25 ± 2 ºC
Value
Parameter Symbol Unit Note
Min. Typ. Max.
Power Supply Voltage Vcc 3.0 3.3 3.6 V -
Ripple Voltage VRP - 50 - mV -
Rush Current IRUSH - - 1.5 A (2)
White - 400 450 mA (3)a
Power Supply Current lcc
Black - 530 580 mA (3)b
Differential Input Voltage for “H” Level VIH - - +100 mV -
LVDS Receiver Threshold “L” Level VIL -100 - - mV -
Terminating Resistor RT - 100 - Ohm -
Note (1) The module should be always operated within above ranges.
Note (2) Measurement Conditions:
+3.3V
Q1 2SK1475
Vcc
C3
FUSE (LCD Module Input)
R1 1uF
47K
(High to Low)
(Control Signal)
Q2
R2
SW 2SK1470
1K
+12V
VR1 47K C2
C1
0.01uF
1uF
0.9Vcc
0.1Vcc
GND
470us
7 / 25
Version 2.1
Issued Date: Jun. 30, 2005
Model No.: N150P5 -L02
Approval
Note (3) The specified power supply current is under the conditions at Vcc = 3.3 V, Ta = 25 ± 2 ºC, DC
Current and fv = 60 Hz, whereas a power dissipation check pattern below is displayed.
HV (Pink)
LCD 1
LV (Black) Inverter
Module 2 A
Current Meter
Note (2) The voltage shown above should be applied to the lamp for more than 1 second after startup.
Otherwise the lamp may not be turned on.
Note (3) The lamp frequency may generate interference with horizontal synchronous frequency from the
display, and this may cause line flow on the display. In order to avoid interference, the lamp
frequency should be detached from the horizontal synchronous frequency and its harmonics as far
as possible.
Note (4) PL = IL ×VL
Note (5) The lifetime of lamp is defined as the time when it continues to operate under the conditions at Ta
= 25 ±2 oC and IL = 6.0 mARMS until one of the following events occurs:
(a) When the brightness becomes ≦ 50% of its original value.
(b) When the effective ignition length becomes ≦ 80% of its original value. (Effective ignition
length is defined as an area that the brightness is less than 70% compared to the center point.)
8 / 25
Version 2.1
Issued Date: Jun. 30, 2005
Model No.: N150P5 -L02
Approval
Note (6) The waveform of the voltage output of inverter must be area-symmetric and the design of the
inverter must have specifications for the modularized lamp. The performance of the Backlight,
such as lifetime or brightness, is greatly influenced by the characteristics of the DC-AC inverter for
the lamp. All the parameters of an inverter should be carefully designed to avoid generating too
much current leakage from high voltage output of the inverter. When designing or ordering the
inverter please make sure that a poor lighting caused by the mismatch of the Backlight and the
inverter (miss-lighting, flicker, etc.) never occurs. If the above situation is confirmed, the module
should be operated in the same manners when it is installed in your instrument.
Note (7) The lamp leakage current is measured by the current difference between in and out. And the
measurement condition is as below:
LCD Module
FG
Low High
Lamp
Current Probe
ILow
Current Probe
IHigh
Inverter
GND
9 / 25
Version 2.1
Issued Date: Jun. 30, 2005
Model No.: N150P5 -L02
Approval
4. BLOCK DIAGRAM
4.1 TFT LCD MODULE
Rxin0(+/-)
SCAN DRIVER IC
Rxin1(+/-) LVDS INPUT /
TIMING CONTROLLER TFT LCD PANEL
(JAE-FI-XB30SL-HF10)
Rxin2(+/-)
INPUT CONNECTOR
(1400x3x1050)
CLK(+/-)
Vcc
CLKEDID
EDID
VEDID
EEPROM
VL LAMP CONNECTOR
(JST-BHSR-02VS-1) BACKLIGHT UNIT
1 HV (Pink)
2 LV (Black)
10 / 25
Version 2.1
Issued Date: Jun. 30, 2005
Model No.: N150P5 -L02
Approval
11 / 25
Version 2.1
Issued Date: Jun. 30, 2005
Model No.: N150P5 -L02
Approval
RXEC+
T/7
DE Vsync Hsync B5 B4 B3 B2
B1 B0 G5 G4 G3 G2 G1
G0 R5 R4 R3 R2 R1 R0
RXOC+
T/7
DE Vsync Hsync B5 B4 B3 B2
B1 B0 G5 G4 G3 G2 G1
G0 R5 R4 R3 R2 R1 R0
12 / 25
Version 2.1
Issued Date: Jun. 30, 2005
Model No.: N150P5 -L02
Approval
13 / 25
Version 2.1
Issued Date: Jun. 30, 2005
Model No.: N150P5 -L02
Approval
14 / 25
Version 2.1
Issued Date: Jun. 30, 2005
Model No.: N150P5 -L02
Approval
15 / 25
Version 2.1
Issued Date: Jun. 30, 2005
Model No.: N150P5 -L02
Approval
16 / 25
Version 2.1
Issued Date: Jun. 30, 2005
Model No.: N150P5 -L02
Approval
6. INTERFACE TIMING
6.1 INPUT SIGNAL TIMING SPECIFICATIONS
The input signal timing specifications are shown as the following table and timing diagram.
Signal Item Symbol Min. Typ. Max. Unit Note
DCLK Frequency 1/Tc 51 54 57 MHz -
Vertical Total Time TV 1058 1066 2046 TH -
Vertical Addressing Time TVD 1050 1050 1050 TH -
DE
Horizontal Total Time TH 762 844 1023 Tc -
Horizontal Addressing Time THD 700 700 700 Tc -
17 / 25
Version 2.1
Issued Date: Jun. 30, 2005
Model No.: N150P5 -L02
Approval
90% 90% t4
t2 t3
- Interface Signal
Valid Data
(LVDS Signal of 0V
Transmitter), VI
t5 t6
OFF ON OFF
- Power for Lamp
Timing Specifications:
470us ≦ t1 ≦ 10 msec
0 < t2 ≦ 50 msec
0 < t3 ≦ 50 msec
t4 ≧ 500 msec
t5 ≧ 200 msec
t6 ≧ 200 msec
Note (1) Please avoid floating state of interface signal at invalid period.
Note (2) When the interface signal is invalid, be sure to pull down the power supply of LCD Vcc to 0 V.
Note (3) The Backlight inverter power must be turned on after the power supply for the logic and the
interface signal is valid. The Backlight inverter power must be turned off before the power supply
for the logic and the interface signal is invalid.
Note (4) Sometimes some slight noise shows when LCD is turned off (even backlight is already off). To
avoid this phenomenon, we suggest that the Vcc falling time had better to follow t7 ≧ 5 msec
(1) When 2.4V ≦ Vcc <3.0V and td≦10ms , the unit must work normally when VCC return to 3.0V.
(2) When Vcc < 2.4V, momentary voltage shall conform to the input voltage sequence.
18 / 25
Version 2.1
Issued Date: Jun. 30, 2005
Model No.: N150P5 -L02
Approval
7. OPTICAL CHARACTERISTICS
7.1 TEST CONDITIONS
Item Symbol Value Unit
o
Ambient Temperature Ta 25±2 C
Ambient Humidity Ha 50±10 %RH
Supply Voltage VCC 3.3 V
Input Signal According to typical value in "3. ELECTRICAL CHARACTERISTICS"
Inverter Current IL 6.0 mA
Inverter Driving Frequency FL 55 KHz
Inverter Sumida H05-4915
The measurement methods of optical characteristics are shown in Section 7.2. The following items
should be measured under the test conditions described in Section 7.1 and stable environment shown in
Note (6).
19 / 25
Version 2.1
Issued Date: Jun. 30, 2005
Model No.: N150P5 -L02
Approval
Normal
θx = θy = 0º
θy- θy+
6 o’clock
y- x+ θX+ = 90º
θy- = 90º
90%
Optical
Response
Gray Level 0
10%
0%
Time
TR TF
66.6ms 66.6ms
20 / 25
Version 2.1
Issued Date: Jun. 30, 2005
Model No.: N150P5 -L02
Approval
LCD Module
LCD Panel
Photometer
Center of the Screen (CA210, BM-5A, CS-1000T)
Field of View = 2º
Horizontal Line
D
D/4 D/2 3D/
Vertical Line
W/4 1 2
X=1 to 5
3W/ 3 4
Active Area
21 / 25
Version 2.1
Issued Date: Jun. 30, 2005
Model No.: N150P5 -L02
Approval
8. PRECAUTIONS
8.1 HANDLING PRECAUTIONS
(1) The module should be assembled into the system firmly by using every mounting hole. Be careful not
to twist or bend the module.
(2) While assembling or installing modules, it can only be in the clean area. The dust and oil may cause
electrical short or damage the polarizer.
(3) Use fingerstalls or soft gloves in order to keep display clean during the incoming inspection and
assembly process.
(4) Do not press or scratch the surface harder than a HB pencil lead on the panel because the polarizer is
very soft and easily scratched.
(5) If the surface of the polarizer is dirty, please clean it by some absorbent cotton or soft cloth. Do not use
Ketone type materials (ex. Acetone), Ethyl alcohol, Toluene, Ethyl acid or Methyl chloride. It might
permanently damage the polarizer due to chemical reaction.
(6) Wipe off water droplets or oil immediately. Staining and discoloration may occur if they left on panel for
a long time.
(7) If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In
case of contacting with hands, legs or clothes, it must be washed away thoroughly with soap.
(8) Protect the module from static electricity, it may cause damage to the C-MOS Gate Array IC.
(9) Do not disassemble the module.
(10) Do not pull or fold the lamp wire.
(11) Pins of I/F connector should not be touched directly with bare hands.
22 / 25
Version 2.1
Issued Date: Jun. 30, 2005
Model No.: N150P5 -L02
Approval
9. PACKING
9.1 CARTON
9.2 PALLET
23 / 25
Version 2.1
Issued Date: Jun. 30, 2005
Model No.: N150P5 -L02
Approval
E207943
N150P5
N141X5 - L03 -L02 Rev.XX MADE IN TAIWAN
01A
01A
XXXXXXXYMDLNNNN
CP135448-01
Serial No.
CMO Internal Use
Year, Month, Date
CMO Internal Use
Revision
CMO Internal Use
24 / 25
Version 2.1