Professional Documents
Culture Documents
®
Flat roof fastening systems
03/2012
Flat roof fastening systems
CONTENT
General information Chapter/page
03/2012
1.1
Single
Flatgroof
p
plyyfastening
membranes
systems
Advantages Advantages
Established technology with the longest High chemical resistance
track record
Suitability for direct application on such
Availability of products for exposed substrates, as bitumen, EPS and XPS
roofing applications with high fire ratings / insulation (polystyrenes)
extended fire resistance
Availability of products for exposed
Easy to repair applications with high fire ratings /
extended fire resistance
Possibility of customized design solutions
(colours, profiles, and roof graphics) Long life expectancy
Homogeneous hot air welded joints Easy to repair
Easy to handle on site Homogeneous hot air welded joints
Suitable for use and exposure in different Easy to handle on site
climatic conditions
Suitable for use and exposure in different
Fast installation independent of the weather climatic conditions
Good vapour permeability Fast installation independent of the
weather
Highly flexible
Outstanding ecological profile
Flame free installation
Flame free installation
Recyclable
The Sarnafil® / Sikaplan® membranes for mechanical fastening have special polyester reinforcement, enabling
high wind load resistance
Mechanically fastened systems are ideal for large, lightweight metal decked structures and buildings, such as distribution
and logistics centres, warehouses, supermarkets and workshops.
03/2012
1.2
Flat Exposed
p fastening
roof roof systems
y
systems
03/2012
1.3
Exposed
p roof
Flat roof systems
y
fastening systems
03/2012
1.4
Exposed
pfastening
Flat roof roof systems
systems
y
03/2012
1.5
Exposed
p roof fastening
Flat roof systems
y systems
03/2012
1.6
Solar
Flat roof roof solution
fastening systems
New
SOL-F - the system for the attachment of
solar installations on flat roofs.
03/2012
1.7
Flat roof fastening systems
Description of complete range: Fasteners and fixings are crucial components, especially in mechanically fastened roof sys-
tems. Wind uplift forces and corrosion of the metal are the two most vertical influences that put tough demands on those
components of a roofing system. Carbon steel solution with special Durocoat® protection ( free of chromium VI) or A4 (AISI 316)
stainless steel version.
Sika products:
Sarnafast® SF 4.8 mm for steel decks,
combined with Washers KT 82x40,
IF/IG-C-82x40, RT 90, DT 70x70,
Sarnabar® / fastening profiles.
Sarnafast® SB 6.3 mm – universal screw
for concrete, steel and wood decks,
combined with Washers KTL 82x40,
IF/IG-C-82x40, RTL 90, DTL 70x70,
Sarnabar® / fastening profiles.
Sarnafast® SBF 6.0 mm (C-steel) - uni-
versal screw for concrete, steel and wood
decks, and Sarnafast® SBF-S 6.0 mm
(stainless) for tube fastenings on steel and
wood decks, combined with Sarnafast®
SFT or Sarnabar® SBT tube fastening
system.
03/2012
1.8
Flat roof fastening systems
Sika products:
Sarnafast® Tube SFT – for spot fastening
Sarnabar® Tube SBT – for linear fastening
with Sarnafast® fastening profiles
Sika products:
Sarnabar® 6/10
Sarnabar® 6
Sarnabar® 6/15 for tube system
03/2012
1.9
Flat roof fastening
g systems
fastening y
systems
03/2012
1.10
Flat roof fastening systems
Today, more than ever, it is essential that construction. Flat roof fastening systems friendly coatings of increasing impor-
the mechanical fastening of insulation are subjected to a wide range of thermal, tance. SFS intec have been setting the
and membrane on flat roofs is both fast static and dynamic stresses. Correct standards for fastener performance in
and efficient. It is equally imperative that design is therefore essential to ensure flat roof applications for many years.
these fasteners are installed correctly that required performance criterion is The complete fastening systems offer
and thereby function properly throughout achieved. Excellent corrosion resistance quality, cost effective and innovative
the expected life of the roof is also critical, with environmentally- fastening solutions.
The convincing advantages of the isofast ® fastening system
A ‘treadfast‘ fastener and stress
plate combination ensures that
the system is safe to walk on.
The entire range is available in
austenitic stainless steel.
A complete system featuring the
IF240 setting tool for rapid fixing
of magazine loaded fasteners.
Maximum corrosion resistance with
safe, chromium VI-free Durocoat®
coatings .
03/2012
1.11
Flat roof fastening systems
A complete range
As well as stand-up setting tools for
fitting single pre-assembled fastener
and sleeve combinations, SFS intec
offers a complete range of installation
tools, including drills, drives and bits for
each application. Efficient installation
demands correct and effective tooling.
03/2012
1.12
Flat roof fastening systems
Substrates
with
with washer
Telescop/sleeve Metal Concrete Timber Critical
Type
yp / code Carbon steel deck deck deck deck
SF
DT, KT
Chapter/page
SB
2.2
1
DTL, KTL
Chapter/page 2.6 3.2 4.2
SBF
SFT, SBT Tube
Chapter/page 2.10 3.11 4.12
BS (ISO-TAK)
Chapter/page RP75, RP45 2.16
TI
SFT, SBT Tube
Chapter/page 3.8
TI (ISO-TAK)
Chapter/page R75, R45 3.14
TS (ISO-TAK)
Chapter/page R75, R45 4.18
TPR-L
DTL, KTL, IE
Chapter/page 5.3
IWF
IRC/W
Chapter/page 4.4
IWF-T
MW
Chapter/page 4.7
TS (ISO-TAK)
Chapter/page R75, R45 4.18
Substrates
with
with washer
Telescop/sleeve Metal Concrete Timber Critical
Type
yp / code Stainless steel deck deck deck deck
IR2-S
IF, IR
Chapter/page 2.8
SBF-S
SFT, SBT Tube
Chapter/page 2.12 4.14
BS-S (ISO-TAK)
Chapter/page RP75, RP45 2.18
DT-S DTL, KTL,
Chapter/page IF/IG-C 3.6
DT-S
SFT, SBT Tube
Chapter/page 3.17
IW-S
IRC/W
Chapter/page 4.10
03/2012
1.13
Flat roof fastening systems
Substrates
with
application
fastener Metal Concrete Timber Critical
Type
yp / code Carbon steel deck deck deck deck
KT
RT-90 termination
washer
RTL-90 termination
washer
Sarnabar® load
LDP-90 distribution
washer
03/2012
1.14
Flat roof fastening systems for steel deck Self drilling fasteners, stress plates and plastic sleeves
2 Fastener
Carbon steel
Sarnafast®
SF
Private Standard
label range Page
` 2.2
Combinations
Fastener and Sarnafast®®
Tubes Sarnabar®®
Private Standard
Standard
label range
range Page
02/2012
2.1
Carbon steel self drilling fastener Flat roof fastening systems for steel deck
Sarnafast® SF
Sarnafast® SF
Technical information
Application
For the fastening of waterproofing membrane and insulation to steel deck. For steel deck thicknesses between
min. 0,63 mm and max. 2 x 1,25 mm.
Material
Fastener Stress plates
SF DT-70x70 / KT-82x40
2 Case hardened carbon steel Steel 1,0 mm
Drive bar
ZA1/4“
Socket
E380 hex
Power screwdriver for manual Stand-up setting tool for the Automated setting tool for the
installation of fasteners installation of isofast® fasteners installation of magazine loaded
and stress plates isofast® fasteners and stress plates
Stress plates
DT-70x70 KT-82x40
03/2012
2.2
Flat roof fastening systems for steel deck Carbon steel self drilling fastener
Sarnafast® SF
Order information
d Hexagon 8 mm A/F
KL
L
KL clamping length | M magazine loaded | d thread diameter | L Length | t thickness of structure | All measures in mm
Order code
SF- 4,8x 60
Product / Application Approval Type d L KL Application range
Carbon steel SF- 4,8x 60 40
t min. steel:
SF- 4,8x 70 50 0,63 mm
SF- 4,8x 80 60
t max. steel:
SF- 4,8x 90 70 2 x 1,25 mm
KL
SF- 4,8x 100 80
SF- 4,8x 110 90 t 2
SF- 4,8x 120 100
ETA 08/0321
SF- 4,8x 130 110 Screw length L: KL + 20 mm
SF- 4,8x 140 120
SF- 4,8x 150 130
SF- 4,8x 160 140
SF- 4,8x 180 160
SF- 4,8x 200 180
SF- 4,8x 220 200
SF- 4,8x 240 220
SF- 4,8x 260 240
SF- 4,8x 280 260
SF- 4,8x 300 280
Stress plates
DT-70X70 KT-82X40
KT
03/2012
2.3
Carbon steel self drilling fastener Flat roof fastening systems for steel deck
Sarnafast® SF
Order information
KL
L
KL clamping length | M magazine loaded | d thread diameter | L Length | t thickness of structure | All measures in mm
Order code
SF- M- 4,8x 60
Product / Application Approval Type M d L KL Application range
Carbon steel SF- M- 4,8x 60 40
t min. steel:
SF- M- 4,8x 70 50 0,63 mm
SF- M- 4,8x 80 60
t max. steel:
SF- M- 4,8x 90 70 2 x 1,25 mm
KL
80
2 SF-
SF-
M-
M-
4,8x
4,8x
100
110 90 t
ETA 08/0321 SF- M- 4,8x 120 100
SF- M- 4,8x 130 110 Screw length L: KL + 20 mm
SF- M- 4,8x 140 120
SF- M- 4,8x 150 130
SF- M- 4,8x 160 140 Attention:
SF- M- 4,8x 180 160 The magazine loaded fastener can only be used with
SF- M- 4,8x 200 180 the IF 240 setting tool.
SF- M- 4,8x 220 200
SF- M- 4,8x 240 220
Stress plates
DT-70X70 KT-82X40
KT
03/2012
2.4
Flat roof fastening systems
Reference
03/2012
2.5
Carbon steel self drilling fastener Flat roof fastening systems for steel deck
Sarnafast® SB
Sarnafast® SB
Technical information
Application
For the fastening of waterproofing membrane and insulation to steel deck. For steel deck thicknesses between
min. 0,63 mm and max. 2 x 1,25 mm.
Material
Fastener Stress plates
SB DTL-70x70 / KTL-82x40
Case hardened carbon steel Steel 1,0 mm
2 Durocoat® corrosion protection: Resistance at 15 cycles Kesternich
Resistance at 15 cycles Kesternich test according to ETAG 006 - D.3.1.
test according to ETAG 006 - D.3.1. and FM requirements
and FM requirements.
Bit holder
ZA1/4“
Bit T30
Power screwdriver for manual Stand-up setting tool for the installa-
installation of fasteners tion of isofast® fasteners and stress
plates with inside drive bar for TORX®
Stress plates
DTL-70x70 KTL-82x40
03/2012
2.6
Flat roof fastening systems for steel deck Carbon steel self drilling fastener
Sarnafast® SB
Order information
KL
L
KL clamping length | M magazine loaded | d thread diameter | L Length | t thickness of structure | All measures in mm
Order code
SB- 6,3x 60
Product / Application Approval Type d L KL Application range
Carbon steel SB- 6,3x 32 15
t min. steel:
SB- 6,3x 50 30 0,63 mm
SB- 6,3x 75 55 KL t max. steel:
SB- 6,3x 100 80 2 x 1,25 mm
t
SB- 6,3x 120 100
SB- 6,3x 140 120 2
ETA 08/0321 SB- 6,3x 160 140
SB- 6,3x 180 160 Screw length L: KL + 20 mm
SB- 6,3x 200 180
SB- 6,3x 230 210
SB- 6,3x 250 230
Stress plates
DTL-70X70 KTL-82X40
03/2012
2.7
Austenitic stainless steel self drilling fastener Flat roof fastening systems for steel deck
isofast ® IR2-S
isofast ® IR2-S
Technical information
Application
For the fastening of waterproofing membrane and insulation to steel deck. For steel deck thicknesses between
min. 0.63 mm and max. 2 x 1,0 mm.
Where the internal relative humidity is in excess of 70%. In chemically aggressive atmospheres or conditions.
For refurbishment applications where the detailed condition of the existing build up is not known or when the build up
contains abrasive layers that may damage the corrosion protection and make it ineffective. Where an extended design life /
warranty is required by the client. For locations with aggressive local conditions (e.g. coastal environments).
2 Material
Fastener Drill point and lead thread section Stress plates
IR2-S Fused and hardened carbon steel, IF-70x70 / IR-82x40
Austenitic stainless steel, grade length 12 mm, corrosion protected Steel 1,0 mm
AISI 316, European Standard
1.4401, grade A4 Resistance at 15 cycles Kesternich
test according to ETAG 006 - D.3.1.
and FM requirements
Drive bar
ZA1/4“
Socket
E380 hex
Stress plates
IF-70x70 IR-82x40
03/2012
2.8
Flat roof fastening systems for steel deck Austenitic stainless steel self drilling fastener
isofast ® IR2-S
Order information
d Hexagon 8 mm A/F
KL
L
KL clamping length | M magazine loaded | d thread diameter | L Length | t thickness of structure | All measures in mm
Order code
IR2-S- 4,8x 60
Product / Application Approval Type d L KL Application range
z
Stainless steel IR2-S- 4,8x 60 40
t min. steel:
IR2-S- 4,8x 80 60 0,63 mm
IR2-S- 4,8x 100 80
t max. steel:
IR2-S- 4,8x 120 100 2 x 1,0 mm
KL
IR2-S- 4,8x 140 120
IR2-S- 4,8x 160 140 t 2
IR2-S- 4,8x 180 160
ETA 08/0321
IR2-S- 4,8x 200 180 Screw length L: KL + 20 mm
IR2-S- 4,8x 220 200
IR2-S- 4,8x 240 220
Stress plates
IF-70X70 IR-82X40
IF
IR
03/2012
2.9
Carbon steel self drilling fastener Flat roof fastening systems for steel deck
Technical information
2 Application
For the fastening of waterproofing membrane and insulation to steel deck. For steel deck thicknesses between
min. 0,63 mm and max. 2 x 1,25 mm.
Material
Fastener Tube
SBF SFT and SBT
Case hardened carbon steel High quality polyamid, PA6
Drive bar
ZA1/4“-M6-300/670
Bit
T25-32-M6-RING
03/2012
2.10
Flat roof fastening systems for steel deck Carbon steel self drilling fastener
Order information
L L L
KL clamping length | M magazine loaded | d thread diameter | L Length | t thickness of structure | All measures in mm
Order code
SBF- 6,0x 60
Product / Application Approval Type d L KL Application range
Carbon steel SBF- 6,0x 35
t min. steel:
SBF- 6,0x 60 0,63 mm
SBF- 6,0x 70
t max. steel:
SBF- 6,0x 80 KL
2 x 1,25 mm
z
Polyamid SFT 50x 40 KL see combination table
SFT 50x 70
SFT 50x 100
SFT 50x 130
ETA 06/0170
SFT 50x 160
SFT 50x 190
SFT 50x 230
Sarnafast® spot fastening system
SFT 50x 300
z
Polyamid SBT 20x 40 KL see combination table
SBT 20x 70
SBT 20x 100
SBT 20x 130
ETA 06/0170
SBT 20x 160
SBT 20x 190
SBT 20x 230
Sarnabar® linear fastening system
SBT 20x 300
03/2012
2.11
Austenitic stainless steel self drilling fastener Flat roof fastening systems for steel deck
Technical information
2 Application
For the fastening of waterproofing membrane and insulation to steel deck. For steel deck thicknesses between
min. 0,63 mm and max. 2 x 1,00 mm.
Material
Fastener Tube
SBF-S SFT and SBT
Austenitic stainless steel, grade High quality polyamid, PA6
AISI 316, European Standard 1.4401,
grade A4
Drive bar
ZA1/4“-M6-300/670
Bit
T25-32-M6-RING
03/2012
2.12
Flat roof fastening systems for steel deck Austenitic stainless steel self drilling fastener
Order information
L
L L
KL clamping length | M magazine loaded | d thread diameter | L Length | t thickness of structure | All measures in mm
Order code
SBF-S- 6,0x 60
Product / Application Approval Type d L KL Application range
z
Stainless steel SBF-S- 6,0x 60
t min. steel:
SBF-S- 6,0x 80 0,63 mm
SBF-S- 6,0x 100
t max. steel:
SBF-S- 6,0x 130 KL
2 x 1,0 mm
Screw length L: KL + 20 mm -
p m ent
el o
i n dev quest!
e
ro g ram le on r
P lab
avai
z
Polyamid SFT 50x 40 KL see combination table
SFT 50x 70
SFT 50x 100
SFT 50x 130
ETA 06/0170
SFT 50x 160
SFT 50x 190
SFT 50x 230
Sarnafast® spot fastening system
SFT 50x 300
z
Polyamid SBT 20x 40 KL see combination table
SBT 20x 70
SBT 20x 100
SBT 20x 130
ETA 06/0170
SBT 20x 160
SBT 20x 190
SBT 20x 230
Sarnabar® linear fastening system
SBT 20x 300
03/2012
2.13
Combination table Flat roof fastening systems for steel deck
0
190 23
0 th 0
Tube SBTxL
0
Tube SFTxL
7 0 6 th
len
g 30
gth 10
0
th
13 th1 leng gth
len gth ng len
g len
len le
Calculation: Roof build up (KL) + 40 mm - tube length (L) = min. fastener length (mm)
Example: 160 mm + 40 mm - 100 mm = 100 mm -> SBF-6,0x100 (SBF-S-6,0x100)
2.14
Flat roof fastening systems
Reference
2.15
Carbon steel self drilling fastener Flat roof fastening systems for steel deck
Technical information
Application
For the fastening of insulation to steel deck. For steel deck thicknesses of between min. 0,63 mm and max. 2 x 1,25 mm.
Material
Fastener Sleeve
BS RP75, for insulation fixing
Case hardened carbon steel High quality polypropylene, PP
Drive bar
ZA1/4“-M6-300/670
Bit
T25-32-M6-RING
03/2012
2.16
Flat roof fastening systems for steel deck Carbon steel self drilling fastener
Order information
L L
KL clamping length | M magazine loaded | d thread diameter | L Length | t thickness of structure | All measures in mm
Order code
BS- 4,8x 50
Product / Application Approval Type d L KL Application range
Carbon steel BS- 4,8x 50
t min. steel:
BS- 4,8x 60 0,63 mm
BS- 4,8x 70
t max. steel:
BS- 4,8x 80 2 x 1,25 mm
BS- 4,8x 90
BS- 4,8x 100
KL
2
BS- 4,8x 110
KL see combination table
z
Plastic RP 45x 30 KL see combination table
RP 45x 60
RP 45x 90
RP 45x 120
ETA 06/0170
RP 45x 150
RP 45x 180
RP 45x 210
03/2012
2.17
Austenitic stainless steel self drilling fastener Flat roof fastening systems for steel deck
2
Technical information
Application
For the fastening of insulation to steel deck. For steel deck thicknesses of between min. 0,63 mm and max. 2 x 1,0 mm.
Where the internal relative humidity is in excess of 70%. In chemically aggressive atmospheres or conditions.
For refurbishment applications where the detailed condition of the existing build up is not known or when the build up
contains abrasive layers that may damage the corrosion protection and make it ineffective. Where an extended design life /
warranty is required by the client. For locations with aggressive local conditions (e.g. coastal environments).
Material
Fastener Sleeve
BS-S RP75 for insulation fixing
Austenitic stainless steel, grade High quality polypropylene, PP
AISI 316, European Standard
RP45 for membrane fixing
1.4401, grade A4
High quality polypropylene, PP
Drive bar
ZA1/4“-M6-300/670
Bit
T25-32-M6-RING
03/2012
2.18
Flat roof fastening systems for steel deck Austenitic stainless steel self drilling fastener
Order information
L L
KL clamping length | M magazine loaded | d thread diameter | L Length | t thickness of structure | All measures in mm
Order code
BS-S- 4,8x 60
Product / Application Approval Type d L KL Application range
z
Stainless steel BS-S- 4,8x 60
t min. steel:
BS-S- 4,8x 80 0,63 mm
BS-S- 4,8x 100
t max. steel:
BS-S- 4,8x 120 2 x 1,0 mm
z
Plastic RP 75x 30
RP 75x 60 KL see combination table
RP 75x 90
RP 75x 120
RP 75x 150
ETA 06/0170
z
Plastic RP 45x 30 KL see combination table
RP 45x 60
RP 45x 90
RP 45x 120
ETA 06/0170
RP 45x 150
RP 45x 180
RP 45x 210
03/2012
2.19
2
Selection of the correct fastener and sleeve combination
KL (mm) Combination sleeve RP45, RP75 and fastener BS-4,8xL
2.20
500
fastener BS-S-4,8xL* 490
480
470
460
*If a length is not available, take the next length. 450
440
Fastener range see chapter. 430
Combination table
KL 420
410
400
390
min. 15 mm 380
ISO-TAK®BS-S / RP75, RP45
Sleeve RP45xL
Sleeve RP75xL
60 70 80 90 100
60 70 80 90 100
60 70 80 90 100
60 70 80 90 100
60 70 80 90 100
60 70 80 90 100
03/2012
60 70 80 90 100 110 120 130 140 150 170 170 190 190 200 220 220 240 240 260 260 300 300 300 300 320 320 360
BS-S-4,8xL
Fastener: BS-4,8xL
Calculation: Roof buildup (KL) - Sleeve length (L) + 35 mm = min. length Type of fastener
Example: 100 mm - 60 mm + 35 mm = 75 mm -> BS-4,8x80
Flat roof fastening systems for steel deck
Flat roof fastening systems for concrete deck Fasteners, stress plates and plastic sleeves
3 Fastener
Carbon steel
Sarnafast®
SB
Private
label
Standard
range Page
` 3.2
Sarnafast®
Fastener and Sarnabar®
Tubes Private Standard
label range Page
Carbon steel / TI
` 3.8
Plastic sleeve SFT, SBT
Carbon steel / SBF
` 3.11
Plastic sleeve SFT, SBT
Carbon steel / TI
` 3.14
Plastic sleeve R45, R75
Austenitic stainless steel / DT-S
` 3.17
Plastic sleeve SFT, SBT
02/2012
3.1
Carbon steel self drilling fastener Flat roof fastening systems for concrete deck
Sarnafast® SB
Sarnafast® SB
Technical information
Application
For the fastening of waterproofing membrane and insulation to concrete deck. Concrete decks (quality ≥ B25), with a set-
ting depth at least 32 mm by using a drilling diameter of 5,5 mm (drilling depth ≥ 45 mm)
Material
Fastener Stress plates
SB DTL-70x70 / KTL-82x40
Case hardened carbon steel Steel 1,0 mm
Bit holder
ZA1/4“
Bit T30
Power screwdriver for manual Stand-up setting tool for the installa-
installation of fasteners tion of isofast® fasteners and stress
plates with inside drive bar for TORX®
Stress plates
DTL-70x70 KTL-82x40
03/2012
3.2
Flat roof fastening systems for concrete deck Carbon steel self drilling fastener
Sarnafast® SB
Order information
KL
L
KL clamping length | M magazine loaded | d thread diameter | L Length | t thickness of structure | All measures in mm
Order code
SB- 6,3x 60
Product / Application Approval Type d L KL Application range
Carbon steel SB- 6,3x 32 0
SB- 6,3x 50 18 KL
SB- 6,3x 75 43 max. L
SB- 6,3x 100 68 Sd
SB- 6,3x 120 88
SB- 6,3x 140 108 min.
ETA 08/0321
SB- 6,3x 160 128 30 mm
SB- 6,3x 180 148
Sd (Setting depth): min. 32 mm
SB- 6,3x 200 168
Predrill Ø 5,5 mm
SB- 6,3x 230 198
SB- 6,3x 250 218 Screw length L: KL+Sd
Stress plates
DTL-70X70 KTL-82X40
03/2012
3.3
Flat roof fastening systems
Reference
3
Tempodrom Concert Hall, Berlin - Germany / 2001
03/2012
3.4
Flat roof fastening systems for concrete deck
Fixing into concrete with conventio- developed and optimised by SFS intec
nal methods is at best complicated. over recent years and has a proven
Using plug free fasteners however track record with respect to its fast
considerably improves installation installation, security of application and
time. The SPIKE® system has been ease of use.
3
Plug-free fixing directly into concrete
With the latest refinements, fixing into
concrete using the SPIKE® system is
even more secure and efficient.
03/2012
3.5
Austenitic stainless steel SPIKE® twister Flat roof fastening systems for concrete deck
Technical information
Application
For the fastening of waterproofing membrane and insulation to solid, dense concrete of minimum grade C12/15.
Where the internal relative humidity is in excess of 70%. In chemically aggressive atmospheres or conditions.
For refurbishment applications where the detailed condition of the existing build up is not known or when the build up
contains abrasive layers that may damage the corrosion protection and make it ineffective. Where an extended design life /
warranty is required by the client. For locations with aggressive local conditions (e.g. coastal environments).
Material
Fastener Stress plates
DT-S DTL-70x70 / ID-70x70
Austenitic stainless steel, grade IF/IG-C-82x40
AISI 316, European Standard KTL-82x40 / IRD-82x40
1.4401, grade A4 Steel 1,0 mm
Resistance at 15 cycles Kesternich
test according to ETAG 006 - D.3.1.
and FM requirements
3 Tools and accessories - details see chapter 6
DB620 ZD15
Stress plates
DTL-70x70 / ID-70x70 IF/IG-C-82x40 KTL-82x40 / IRD-82x40
Stress plate for insulation Stress plate for membrane Stress plate for membrane
and insulation on hard subrates
03/2012
3.6
Flat roof fastening systems for concrete deck Austenitic stainless steel SPIKE® twister
Order information
KL clamping length | M magazine loaded | d thread diameter | L Length | t thickness of structure | All measures in mm
Order code
DT-S- 4,8x 28
Product / Application Approval Type d L KL Drill bits Application range
z
Stainless steel DT-S- 4,8x 28 3 4,8x160
KL
DT-S- 4,8x 32 7 160 max. L
DT-S- 4,8x 38 13 160
Sd
DT-S- 4,8x 51 26 160
DT-S- 4,8x 64 39 160 min.
DT-S- 4,8x 89 64 210 30 mm
DT-S- 4,8x 115 90 210 Sd (Setting depth): min. 25 mm
ETA 08/0321 DT-S- 4,8x 140 115 260 Predrill Ø 4,8 mm
Screw length L: KL+Sd
Stress plates
DTL-70X70 / ID-70x70 IF/IG-C-82X40 KTL-82X40 / IRD-82x40
IF/IG-C
03/2012
3.7
Carbon steel concrete fastener Flat roof fastening systems for concrete deck
Technical information
Application
For the fastening of waterproofing membrane and insulation to solid, dense concrete of minimum grade C12/15, with a
setting depth at least 32 mm by using a drilling diameter of 5,0 mm (drilling depth ≥ 30 mm)
Material
Fastener Tube
3 TI SFT and SBT
Case hardened carbon steel High quality polyamid, PA6
Drive bar
ZA1/4“-M6-300/670
Bit
T25-32-M6-RING
Stand-up setting tool for the Electro-pneumatic hammer drill for Power screwdriver for manual
installation of ISO-TAK ® fasteners drilling into concrete and masonry installation of fasteners
and sleeves
03/2012
3.8
Flat roof fastening systems for concrete deck Carbon steel concrete fastener
Order information
T25 Ø 9,6 mm
d
L
L L
KL clamping length | M magazine loaded | d thread diameter | L Length | t thickness of structure | All measures in mm
Order code
TI-T25- 6,3x 32
Product / Application Approval Type d L KL Application range
Carbon steel TI-T25- 6,3x 32
TI-T25- 6,3x 50
TI-T25- 6,3x 60
TI-T25- 6,3x 70
z
Polyamid SFT 50x 40 KL see combination table
SFT 50x 70
SFT 50x 100
SFT 50x 130
SFT 50x 160
SFT 50x 190
Sarnafast® spot fastening system SFT 50x 230
ETA 06/0170
SFT 50x 300
z
Polyamid SBT 20x 40 KL see combination table
SBT 20x 70
SBT 20x 100
SBT 20x 130
SBT 20x 160
SBT 20x 190
Sarnabar® linear fastening system ETA 06/0170
SBT 20x 230
SBT 20x 300
03/2012
3.9
Combination table Flat roof fastening systems for concrete deck
400
400
390
390
380
380
KL 370
370
360
360
350
350
340 t 20 mm 340
330
330
320
320
310
310 KL = Clamping Length
300
300
290
290
280
280
270
270
260
260
250
250
240
3 240
230
220
230
220
210
210
200 200
190 190
180
180
170 170
160 160
150
150
140
140
130
130
120
120
110 110
100 100
0
16
0 30
70 0 th 90 gth
gth h1
3 g h1 30 len
Tube SBTxL
Tube SFTxL
len
00 gt len gt 2
gt h1 len len gth
len len
Calculation: Roof build up (KL) + 40 mm - tube length (L) = min. fastener length (mm)
Example: 160 mm + 40 mm - 100 mm = 100 mm -> TI-T25-6,3x100
03/2012
3.10
Flat roof fastening systems for concrete deck Carbon steel concrete fastener
Technical information
Application
For the fastening of waterproofing membrane and insulation to solid, dense concrete of minimum grade C12/15, with a
setting depth at least 20 mm by using a drilling diameter of 5,0 mm (drilling depth ≥ 30 mm)
Material
Fastener Tube
SBF SFT and SBT
Case hardened carbon steel High quality polyamid, PA6
3
Durocoat® corrosion protection:
Resistance at 15 cycles Kesternich
test according to ETAG 006 - D.3.1.
and FM requirements
Drive bar
ZA1/4“-M6-300/670
Bit
T25-32-M6-RING
02/2012
03/2012
3.11
Carbon steel concrete fastener Flat roof fastening systems for concrete deck
Order information
L L L
KL clamping length | M magazine loaded | d thread diameter | L Length | t thickness of structure | All measures in mm
Order code
SBF- 6,0x 60
Product / Application Approval Type d L KL Application range
Carbon steel SBF- 6,0x 35
SBF- 6,0x 60
SBF- 6,0x 70 KL
SBF- 6,0x 80
z
Polyamid SFT 50x 40 KL see combination table
SFT 50x 70
SFT 50x 100
SFT 50x 130
ETA 06/0170
SFT 50x 160
SFT 50x 190
SFT 50x 230
Sarnafast® spot fastening system
SFT 50x 300
z
Polyamid SBT 20x 40 KL see combination table
SBT 20x 70
SBT 20x 100
SBT 20x 130
ETA 06/0170
SBT 20x 160
SBT 20x 190
SBT 20x 230
Sarnabar® linear fastening system
SBT 20x 300
03/2012
3.12
Flat roof fastening systems for concrete deck Combination table
400
400
390
390
380
380
KL 370
370
360
360
350
350
340 t 32 mm 340
330
330
320
320
310
310
KL = Clamping Length 300
300
290
290
280
280
270
270
260
260
250
250
240
240
230
220
230
3
220
210
210
200 200
190 190
180
180
170 170
160 160
150
150
140
140
130
130
120
120
110 110
100 100
0 0
16 30
70 13
0 gth 190 0 gth
Tube SBTxL
Tube SFTxL
th 00 gth len th h2
3 len
le ng
gt h1 len leng gt
len len
Calculation: Roof build up (KL) + 50 mm - tube length (L) = min. fastener length (mm)
Example: 160 mm + 50 mm - 100 mm = 110 mm -> SBF-6,0x110
03/2012
3.13
Carbon steel concrete fastener Flat roof fastening systems for concrete deck
Technical information
Application
For the fastening of waterproofing membrane and insulation to solid, dense concrete of minimum grade C12/15.
Material
Fastener Sleeve
3 TI
Case hardened carbon steel RP75 for insulation fixing
High quality polypropylene, PP
Durocoat® corrosion protection:
Resistance at 15 cycles Kesternich RP45 for membrane fixing
test according to ETAG 006 - D.3.1. High quality polypropylene, PP
and FM requirements
Drive bar
ZA1/4“-M6-300/670
Bit
T25-32-M6-RING
Stand-up setting tool for the Electro-pneumatic hammer drill for Power screwdriver for manual
installation of ISO-TAK ® fasteners drilling into concrete and masonry installation of fasteners
and sleeves
03/2012
3.14
Flat roof fastening systems for concrete deck Carbon steel concrete fastener
Order information
T25 Ø 9,6 mm
d
L L
KL clamping length | M magazine loaded | d thread diameter | L Length | t thickness of structure | All measures in mm
Order code
TI-T25- 6,3x 32
Product / Application Approval Type d L KL Application range
Carbon steel TI-T25- 6,3x 32
TI-T25- 6,3x 50
TI-T25- 6,3x 60
KL
TI-T25- 6,3x 70
TI-T25- 6,3x 80
min. 15 mm
TI-T25- 6,3x 90
Sd
TI-T25- 6,3x 100
TI-T25- 6,3x 120
TI-T25- 6,3x 140 Sd (Setting depth): min. 20 mm
TI-T25- 6,3x 160 Predrill Ø 5,0 mm
Thickness concrete deck t: min. 40 mm.
Concrete quality minimum C12/15.
Insulation compressive strength min. 0,07 N/mm2.
Depth of pilot hole to be 10 - 20 mm deeper than the setting depth,
z
Plastic R 45x 15
depending on site conditions.
3
R 45x 35 KL see combination table
R 45x 65
R 45x 85
R 45x 105
R 45x 135
R 45x 165
ETA 06/0170
R 45x 185
R 45x 195
R 45x 225
R 45x 255
R 45x 285
R 45x 325
R 45x 365
R 45x 405
z
Plastic R 75x 15
R 75x 35 KL see combination table
R 75x 65
R 75x 85
R 75x 105
R 75x 135
ETA 06/0170
R 75x 165
R 75x 185
R 75x 195
R 75x 225
R 75x 255
R 75x 285
03/2012
3.15
3
Selection of the correct fastener and sleeve combination
3.16
KL (mm) Combination sleeve R45, R75 and TI-T25-6,3xL 500
490
480
470
460
450
440
Combination table
430
420
410
KL 400
390
ISO-TAK ® TI-T25 / R45, R75
380
370
R45 R75 TI-T25-6,3xL 360
min. 15 mm 350
340
min. setting 330
320
depth 20 mm 310
300
290
280
270
260
250
240
230
220
210
200
190
180
170
160
150
140
130
120
110
100
90
80
70
60
50 )
40 ) R45
30 5 R45 (only
th 1 only 05
ve leng h 35 h 65 R45) 65 ( ng th 4
ngt ngt h 85 5 65 nly h3
Slee ve le ve le ngt 05 h 13 th 1 5 (o ng t ve le
Slee Slee ve le ngth 1 ngt leng 185 t h 32 ve le Slee
Slee e le e le ve th 5 5 leng Slee
leev Sleev Slee leng 5 h 25 h 285 ve
S ve h 19 h 22 ngt ngt Slee
Slee ngt ngt ve le
ve le ve le ve le Slee
Slee Slee Slee
Sleeve R45xL
Sleeve R75xL
50 60 70 80
50 60 70 80 90
50 60 70 80
50 60 70 80
50 60 70 80 90
50 60 70 80 90
50 60 70 80
50 60 70
50 60 70 80 90
50 60 70 80 90
03/2012
50 60 70 80 90
50 60 70 80 90 100
50 60 70 80 90 100
50 60 70 80 90 100
Fastener TI-T25-6,3xL
50 60 70 80 90 100 120 120 140
20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20
20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20
20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 30 20 30
Setting
depth**
(mm)
20 20 20 20 20 20 20 20 20 20 20 20 20
**Depth of pilot hole to be 10 - 20 mm deeper than the Calculation: Roof buildup (KL) - Sleeve length (L) + 35 mm = min. length Type of fastener
setting depth, depanding on site conditions. Example: 160 mm - 135 mm + 35 mm = 60 mm -> TI-T25-6,3x60
Flat roof fastening systems for concrete deck
Flat roof fastening systems for concrete deck Austenitic stainless steel concrete fastener
SPIKE® twister DT-S / Sarnafast® SFT, SPIKE® twister DT-S / Sarnabar® SBT
SPIKE® twister DT-S / Sarnafast® SFT, SPIKE® twister DT-S / Sarnabar® SBT
Technical information
Application
For the fastening of waterproofing membrane and insulation to solid, dense concrete of minimum grade C12/15.
Material
Fastener Tube
DT-S SFT and SBT 3
Austenitic stainless steel, grade High quality polypamid, PA6
AISI 316, European Standard 1.4401,
grade A4
03/2012
3.17
Austenitic stainless steel concrete fastener Flat roof fastening systems for concrete deck
SPIKE® twister DT-S / Sarnafast® SFT, SPIKE® twister DT-S / Sarnabar® SBT
Order information
L
L L
KL clamping length | M magazine loaded | d thread diameter | L Length | t thickness of structure | All measures in mm
Order code
DT-S- 4,8x 28
Product / Application Approval Type d L KL Drill bits Application range
z
Stainless steel DT-S- 4,8x 38 4,8x160
z
Polyamid SFT 50x 40 KL see combination table
SFT 50x 70
SFT 50x 100
SFT 50x 130
SFT 50x 160
SFT 50x 190
SFT 50x 230
Sarnafast® spot fastening system
SFT 50x 300
z
Polyamid SBT 20x 40 KL see combination table
SBT 20x 70
SBT 20x 100
SBT 20x 130
SBT 20x 160
SBT 20x 190
SBT 20x 230
Sarnabar® linear fastening system
SBT 20x 300
03/2012
3.18
Flat roof fastening systems for concrete deck Combination table
SPIKE® twister DT-S / Sarnafast® SFT, SPIKE® twister DT-S / Sarnabar® SBT
400
400
390
390
380
380
KL 370
370
360
360
350
350
340 t 25 mm 340
330
330
320
320
310
310
300
300 KL = Clamping Length
290
290
280
280
270
270
260
260
250
250
240
240
230
230
220
220 3
210
210
200 200
190 190
180
180
170 170
160 160
150
150
140
140
130
130
120
120
110 110
100 100
0
23
0 30
60 190 gth
Tube SBTxL
70
Tube SFTxL
0 1 th
gth 00 13 gth gth ng len
len gth1 gth len len
le
len len
89 99 115 115
64 89 89 115 115 Note:
Fastener DT-S-4,8xL
Calculation: Roof build up (KL) + 45 mm - tube length (L) = min. fastener length (mm)
Example: 160 mm + 45 mm - 100 mm = 105 mm -> DT-S-4,8x115
03/2012
3.19
3
03/2012
3.20
Flat roof fastening systems for timber deck Fasteners, stress plates and plastic sleeves
4 Fastener
Carbon steel
Sarnafast®
SB
Private
label
Standard
range Page
` 4.2
Sarnafast®
Fastener and
Sarnabar®
Tubes
Private Product
label code Page
SBF
Carbon steel / Plastic sleeve ` 4.12
SFT, SBT
SBF-S
Austenitic stainless steel ` 4.14
SFT, SBT
TS
Carbon steel / Plastic sleeve ` 4.18
R45, R75
03/2012
4.1
Carbon steel self drilling fastener Flat roof fastening systems for timber deck
Sarnafast® SB
Sarnafast® SB
Technical information
Application
For the fastening of waterproofing membrane and insulation to timber deck. Solid wood 24 mm or thicker and plywood/
OSB 22 mm or thicker; fastener length = roof build up + 30 mm.
Material
Fastener Stress plates
SB DTL-70x70 / KTL-82x40
Case hardened carbon steel Steel 1,0 mm
4 Bit holder
ZA1/4“
Bit T30
Power screwdriver for manual Stand-up setting tool for the installa-
installation of fasteners tion of isofast® fasteners and stress
plates with inside drive bar for TORX®
Stress plates
DTL-70x70 KTL-82x40
03/2012
4.2
Flat roof fastening systems for timber deck Carbon steel self drilling fastener
Sarnafast® SB
Order information
KL
L
KL clamping length | M magazine loaded | d thread diameter | L Length | t thickness of structure | All measures in mm
Order code
SB- 6,3x 60
Product / Application Approval Type d L KL Application range
Carbon steel SB- 6,3x 32 2
SB- 6,3x 50 20
KL
SB- 6,3x 75 45 L
SB- 6,3x 100 70 Sd
SB- 6,3x 120 90
SB- 6,3x 140 110
Fastener length = roof build up + 30 mm
ETA 08/0321 SB- 6,3x 160 130 Sd (settig depth) = min. 30 mm
SB- 6,3x 200 170 Screw length = KL + Sd
SB- 6,3x 230 200
SB- 6,3x 250 220 Delivery note: 1 T30 bit is included at each box.
Stress plates
DTL-70X70 KTL-82X40
03/2012
4.3
Carbon steel fastener Flat roof fastening systems for timber deck
isofast ® IWF
isofast ® IWF
Technical information
Application
For the fastening of waterproof membrane to timber deck. The recommended minimum thickness of timber boarding, for
example plywood, oriented strand board (OSB) is 18 mm.
Material
Fastener Stress plates
IWF IRC/W-82x40
Case hardened carbon steel Steel 1,0 mm
Stress plates
IRC/W-82x40
4
Stress plate for membrane and
insulation
03/2012
4.4
Flat roof fastening systems for timber deck Carbon steel fastener
isofast ® IWF
Order information
KL
L
KL clamping length | M magazine loaded | d thread diameter | L Length | t thickness of structure | All measures in mm
Order code
IWF- 5,2x 25
Product / Application Approval Type d L KL Application range
Carbon steel IWF- 5,2x 25 *
18 mm
IWF- 5,2x 35 5
IWF- 5,2x 45 15
IWF- 5,2x 55 25
KL
18 mm
Screw length L: KL + 30 mm
Stress plates
IRC/W-82X40
IRC/W
03/2012
4.5
Carbon steel fastener Flat roof fastening systems for timber deck
isofast ® IWF-T
The isofast® IWF-T-B40 is an ideal The special design of the plate allows
fastening system for the direct fixing the pre-assembling with IWF fasteners.
of membranes to timber sub frames Furthermore, by using the setting tool
(wood and synthetics like triple-layer, MV28 a fast and secure setting is
ply, wooden frames, etc.). possible.
03/2012
4.6
Flat roof fastening systems for timber deck Carbon steel fastener
isofast ® IWF-T
isofast ® IWF-T
Technical information
Application
For the fastening of waterproof membrane to timber deck. The recommended minimum thickness of timber boarding, for
example plywood, oriented strand board (OSB) is 18 mm.
Material
Fastener Stress plates
IWF-T MW-40-FH
With pre-assembled stress plate Steel 1,0 mm
(MW-40-FH), case hardened carbon
steel Resistance at 15 cycles Kesternich
test according to ETAG 006 - D.3.1.
Durocoat® corrosion protection: and FM requirements
Resistance at 15 cycles Kesternich
test according to ETAG 006 - D.3.1.
and FM requirements
Stress plates
MW-40-FH
03/2012
4.7
Carbon steel fastener Flat roof fastening systems for timber deck
isofast ® IWF-T
Order information
KL
KL clamping length | M magazine loaded | d thread diameter | L Length | t thickness of structure | All measures in mm
Order code
IWF-T-B40- 5,0x 25
Product / Application Approval Type d L KL Application range
Carbon steel IWF-T-B40- 5,2x 25 *
18 mm
IWF-T-B40- 5,2x 35 5
IWF-T-B40- 5,2x 45 15
IWF-T-B40- 5,2x 55 25
KL
18 mm
Screw length L: KL + 30 mm
Stress plates
MW-40-FH
03/2012
4.8
Flat roof fastening systems for timber deck Austenitic stainless steel fastener
isofast ® IW-S
03/2012
4.9
Austenitic stainless steel fastener Flat roof fastening systems for timber deck
isofast ® IW-S
isofast ® IW-S
Technical information
Application
For the fastening of waterproof membrane to timber deck. The recommended minimum thickness of timber boarding, for
example plywood, oriented strand board (OSB) is 18 mm.
Where the internal relative humidity is in excess of 70%. In chemically aggressive atmospheres or conditions.
For refurbishment applications where the detailed condition of the existing build up is not known or when the build up
contains abrasive layers that may damage the corrosion protection and make it ineffective. Where an extended design life /
warranty is required by the client. For locations with aggressive local conditions (e.g. coastal environments).
Material
Fastener Stress plates
isofast® IW-S IRC/W-82x40
Austenitic stainless steel, grade Steel 1,0 mm
AISI 304, European Standard
1.4301, grade A2 Resistance at 15 cycles Kesternich
test according to ETAG 006 - D.3.1.
and FM requirements
Stress plates
IRC/W-82x40
03/2012
4.10
Flat roof fastening systems for timber deck Austenitic stainless steel fastener
isofast ® IW-S
Order information
KL
L
KL clamping length | M magazine loaded | d thread diameter | L Length | t thickness of structure | All measures in mm
Order code
IW-S- 5,0x 45
Product / Application Approval Type d L KL Application range
z
Stainless steel IW-S- 5,0x 45 15
18 mm
KL
18 mm
Screw length L: KL + 30 mm
Stress plates
IRC/W-82X40
IRC/W
03/2012
4.11
Carbon steel self drilling fastener Flat roof fastening systems for timber deck
Technical information
Application
For the fastening of waterproof membrane and insulation to timber deck. Solid wood 24 mm or thicker and plywood/OSB
22 mm or thicker; fastener length = roof build up + 30 mm.
Material
Fastener Tube
SBF SFT and SBT
Case hardened carbon steel High quality polyamid, PA6
4
Tools and accessories - details see chapter 6
DI650 TP10, TP19, TP30
Bit holder
ZA1/4“
Bit T25
03/2012
4.12
Flat roof fastening systems for timber deck Carbon steel self drilling fastener
Order information
L L L
KL clamping length | M magazine loaded | d thread diameter | L Length | t thickness of structure | All measures in mm
Order code
SBF- 6,0x 60
Product / Application Approval Type d L KL Application range
Carbon steel SBF- 6,0x 35
SBF- 6,0x 60
SBF- 6,0x 70
SBF- 6,0x 90
SBF- 6,0x 100
ETA 08/0321 SBF- 6,0x 110
SBF- 6,0x 130 Screw length L: KL + 30 mm
SBF- 6,0x 160
SBF- 6,0x 180
SBF- 6,0x 200
z
Polyamid SFT 50x 40 KL see combination table
SFT 50x 70
SFT 50x 100
SFT 50x 130
ETA 06/0170
SFT 50x 160
SFT 50x 190
SFT 50x 230
Sarnafast® spot fastening system SFT 50x 300
z
Polyamid SBT
SBT
20x
20x
40
70
KL see combination table
4
SBT 20x 100
SBT 20x 130
ETA 06/0170
SBT 20x 160
SBT 20x 190
Sarnabar® linear fastening system SBT 20x 230
SBT 20x 300
03/2012
4.13
Austenitic stainless steel self drilling fastener Flat roof fastening systems for timber deck
Technical information
Application
For the fastening of waterproof membrane and insulation to timber deck. Solid wood 24 mm or thicker and plywood/OSB
22 mm or thicker; fastener length = roof build up + 30 mm.
Material
Fastener Tube
SBF-S SFT and SBT
Austenitic stainless steel, grade High quality polyamid, PA6
AISI 316, European Standard 1.4401,
grade A4
Drive bar
ZA1/4“-M6-300/670
Bit
T25-32-M6-RING
03/2012
4.14
Flat roof fastening systems for timber deck Austenitic stainless steel self drilling fastener
Order information
L
L L
KL clamping length | M magazine loaded | d thread diameter | L Length | t thickness of structure | All measures in mm
Order code
SBF-S- 6,0x 60
Product / Application Approval Type d L KL Application range
Stainless steel SBF-S- 6,0x 60
SBF-S- 6,0x 80
SBF-S- 6,0x 100 KL
SBF-S- 6,0x 130
ETA 08/0321
-
Screw length L: KL + 30 mm
p m ent
el o
i n dev quest!
e
ro g ram le on r
P lab
avai
03/2012
4.15
Combination table Flat roof fastening systems for timber deck
Combination tube
Combination SFT and
sleeve SFTfastener SBF-T25-6,0xL
and fastener SBF-6,0xL(SBF-S-6,0xL)
(SBF-S-6,0xL) 400
400 SBT and fastener SBF-T25-6,0xL (SBF-S-6,0xL)
SBT and fastener SBF-6,0xL (SBF-S-6,0xL) 390
390
380
380
370
370
360
360
350
350
340 340
CL
KL 330
330
320
320
310
310
300
t t 24
30 mm
mm 300
t 6 mm 290
290
280
280
270
270 t = min. 22 mm
260
260 KL = Clamping Length
250
250
240
240
230
230
220
220
210
210
200 200
190 190
180
180
170 170
160 160
150
150
140
140
130
130
4 120
110 110
120
100 100
0 0
70 23 30
th g th g th
Tube SBTxL
0 90
Tube SFTxL
leng 10
0 13 1 60
th1 len len
gth gth gth g
len len len len
Calculation: Roof build up (KL) + 50 mm - tube length (L) = min. fastener length (mm)
Example: 160 mm + 50 mm - 100 mm = 110 mm -> SBF-6,0x110 (SBF-S-6,0x110)
03/2012
4.16
Flat roof fastening systems for timber deck Carbon steel fastener
03/2012
4.17
Carbon steel self drilling fastener Flat roof fastening systems for timber deck
Technical information
Application
For the fastening of waterproof membrane to timber deck. The recommended minimum thickness of timber boarding, for
example plywood, oriented strand board (OSB) is 18 mm.
Material
Fastener Sleeve
TS RP75 for insulation fixing
Case hardened carbon steel High quality polypropylene, PP
Bit holder
ZA1/4“
Bit T25
Stand-up setting tool for the instal- Power screwdriver for manual
lation of ISO-TAK ® fasteners and installation of fasteners
sleeves
03/2012
4.18
Flat roof fastening systems for timber deck Carbon steel self drilling fastener
Order information
L L
KL clamping length | M magazine loaded | d thread diameter | L Length | t thickness of structure | All measures in mm
Order code
TS-T25- 6,0x 50
Product / Application Approval Type d L KL Application range
Carbon steel TS-T25- 6,0x 50
TS-T25- 6,0x 60
TS-T25- 6,0x 70
TS-T25- 6,0x 80
TS-T25- 6,0x 90
KL
TS-T25- 6,0x 100
TS-T25- 6,0x 110
TS-T25- 6,0x 120
TS-T25- 6,0x 130
TS-T25- 6,0x 140
TS-T25- 6,0x 160
TS-T25- 6,0x 180
TS-T25- 6,0x 200
TS-T25- 6,0x 220
TS-T25- 6,0x 240
z
Plastic R 45x 15
R 45x 35 KL see combination table
R 45x 65
R 45x 85
R 45x 105
R 45x 135
R 45x 165
ETA 06/0170
R 45x 185
R 45x 195 4
R 45x 225
R 45x 255
R 45x 285
R 45x 325
R 45x 365
R 45x 405
z
Plastic R 75x 30
R 75x 60 KL see combination table
R 75x 90
R 75x 120
ETA 06/0170
R 75x 150
03/2012
4.19
4
Selection of the correct sleeve and fastener combination
KL (mm) Combination sleeve R45, R75 and fastener TS-T25-6,0xL
4.20
500
490
480
470
460
450
440
430
Combination table
420
410
ISO-TAK ® TS / R45, R75
400
390
380
KL R45 R75 370
TS-T25-6,0xL 360
350
340
330
320
min. 15 mm 310
300
290
Setting depth 280
min. 30 mm 270
260
250
240
230
220
210
200
190
180
170
160
150
140
130
120
110
100
90
80
70
60
50
40
30
h4 0
ngt 0
ve le h 70 h 10
Slee ngt ngt h 130
ve le ve le ngt 160 0 0
Slee Slee e le h h 19 h 23
S leev ngt ngt ngt 0 5
ve le ve le ve le h 30 65 h 40
Slee Slee Slee ngt 5 th 3 ngt
ve le 95 25 5 h 32 ng ve le
Slee th 1 th 2 h 25 285 ngt e le Slee
ng ng ngt h ve le Sleev
ve le ve le ngt
ve le ve le Slee
Sleeve R45xL
Sleeve R75xL
Slee Slee Slee Slee
60 70 80 90
60 70 80 90 100
60 70 80 90
60 70 80 90
60 70 80 90 100
60 70 80 90 100
60 70 80 90
60 70 80
03/2012
60 70 80 90 100
60 70 80 90 100
60 70 80 90 100
60 70 80 90 100 110
60 70 80 90 100 110
Fastener TS-T25-6xL
60 70 80 90 100 110
60 70 80 90 100 110 120 130 140
Calculation: Roof buildup (KL) - Sleeve length (L) + 45 mm = min. length Type of fastener
Example: 100 mm - 85 mm + 45 mm = 60 mm -> TS-T25-6,0x60
Flat roof fastening systems for timber deck
Flat roof fastening systems for critical deck Peel Rivet System
Peel Rivet
Standard
range
TPR-L
Page
` 5.3
03/2012
5.1
Peel Rivet System Flat roof fastening systems for critical deck
Critical sub-structures:
5 The Peel Rivet fastening system is
the ideal solution
After pre-drilling the sub-structure, the
peel rivets can be rapidly fitted using
the TPR 55 setting tool. As the centre
pin is withdrawn, the rivet is defor-
med, creating four arms which pro-
duce a contact surface equivalent to
five times the shaft diameter. In com-
bination with recommended stress
plates the rivets provide for a con-
sistently high pullout requirement.
03/2012
5.2
Flat roof fastening systems for critical deck Peel Rivet System
Technical information
Application
For the fastening of waterproof membrane and insulation to aluminium, thin concrete, wood wool and problem decks,
where conventional threaded fasteners may not achieve sufficient performance.
TPR-L
Minimum thickness for steel deck: t t 0,50 mm
Minimum thickness for aluminuim deck: t t 0,60 mm
Minimum clamping length: KL t 13,0 mm
Generally
To be installed via a pilot hole. Application tests are required on all projects to determine the suitability and performance.
Material
Fastener Stress plates
TPR-L ID-70x70 / IE-C-82x40 / IRD-82x40
Body: Aluminium/magnesium alloy Steel 1,0 mm, zinc plated
Mandrel: Zinc plated steel
Resistance at 15 cycles Kesternich
test according to ETAG 006 - D.3.1.
and FM requirements
Stress plate for insulation Stress plate for membrane Stress plate for membrane
and insulation on hard substrates and insulation
03/2012
5.3
Peel Rivet System Flat roof fastening systems for critical deck
Order information
KL
KL clamping length | M magazine loaded | d thread diameter | L Length | t thickness of structure | All measures in mm
Order code
TPR-L 6,3x 38
Product / Application Approval Type d L KL Application range
È
Aluminium TPR-L 6,3x 38 13
KL t min. steel:
TPR-L- 6,3x 51 26 0,5 mm
TPR-L- 6,3x 64 39
t min. alu:
TPR-L- 6,3x 76 51 0,6 mm
TPR-L- 6,3x 88 63
TPR-L- 6,3x 102 77 Min. KL = 13 mm due to the mandrel which stays inside the
TPR-L- 6,3x 127 102 body of the Peel Rivet.
ETA 08/0321
TPR-L- 6,3x 152 127 Pull-out tests are recommended, if thickness of substrate is
TPR-L- 6,3x 178 153 lower as t min.
TPR-L- 6,3x 203 178
TPR-L- 6,3x 229 204
TPR-L- 6,3x 254 229
5 Stress plates
DTL-70x70 / ID-70X70 IE-C-82X40 KTL-82x40 / IRD-82X40
IE - C
03/2012
5.4
Tools and accessories
6 Steel deck
Timber deck
Concrete deck
Product code
` 6.2
03/2012
6.1
Installation tools Tools and accessories
Tools
IF240
Technical details
Application Fasteners
Automated setting tool for the fast and economic installation Diameter: 4,8 mm and 6,0 mm
of magazine loaded isofast® fasteners and stress plates Length: 50 mm to 240 mm
Technical details
Application Fasteners
Fasteners
®
Stand-up setting tool for the installation of isofast fasteners Diameter: 4,8 mm
Drive: Hexagon head
and stress plates. Length:
Diameter: 4,8 mmmm to 300 mm
50
Fastener assembly may be undertaken on site if necessary. Length: 50 mm to 300 mm
Fasteners
6 Drive: Torx (25,30)
Diameter: 6,0 mm and 6,3 mm
Length: 50 mm to 250 mm
03/2012
6.2
Tools and accessories Installation tools
Tools
Technical details
Power tool: DI 650
Wattage: 650 W
Max. revs: 2000 rpm
Power supply: 110V / 20V
Max. torque: 20 Nm
Tool: Weight / Lenght:
TP10: 2,7 Kg 550 mm
TP19: 3,0 Kg 730 mm
TP30: 3,1 Kg 760 mm
Application
Stand-up setting tool for the installation of fasteners and sleeves
DI650
Technical details
Power tool: DI 650
Wattage: 650 W
Max. revs: 2000 rpm
Power supply: 110V / 20V
Max. torque: 20 Nm
Overall length: 290 mm
Weight: 1,6 Kilogram
Application
Power screwdriver for manual installation of fasteners
03/2012
6.3
Installation tools Tools and accessories
Tools
IT19
Technical details
Power tool: DI 650
Wattage: 650 W
Max. revs: 2000 rpm
Power supply: 110V / 230V
Height: 900 mm
Weight: 2,7 Kg
Application
Automated setting tool for the fast, secure and economic installation
of the ISO-TAK® fasteners
DB620
Technical details
Wattage: 620 W
Max. revs: 870 rpm
Power supply: 110V / 230V
Weight: 2,4 Kg
Drive connection: SDS-Plus
Application
Hammer drill for pre-drilling into concrete and masonry
03/2012
6.4
Tools and accessories Installation tools
Tools
Technical details
Wattage: 600 W
Max. revs: 600 rpm
Power supply: 110V / 230V
Overall length: 480 mm
Weight: 3 Kg
Application
Electric rivetting tool for the fast installation of TPR-L and TPR Peel
Rivet fasteners
Application
Including 4 nozzles 6
03/2012
6.5
Accessories Tools and accessories
Order information
SDS Carbide-geometry
d
Dynamic, chisel-shaped drill bit head
Multi-fluted, spacious KVS-spiral
F
Unique KVS-flute design
L
Order code
SDS- 4,8x 110/ 50- 4PLUS
Type d L F Code Application range
SDS- 4,8x 110/ 50- 4PLUS SPIKE® twister DT-S-4,8xL
SDS- 4,8x 160/ 100- 4PLUS TI-T25-6,3xL
SDS- 4,8x 210/ 150- 4PLUS
SDS- 4,8x 260/ 200- 4PLUS
SDS- 4,8x 310/ 250- 4PLUS
SDS- 4,8x 360/ 300- 4PLUS
SDS- 5,0x 110/ 50- 4PLUS TI-T25-6,3xL
®
SDS- 5,0x 160/ 100- 4PLUS Sarnafast SBF SDS- 5,0x 160/ 100- 4PLUS-Sika
SDS- 5,0x 210/ 150- 4PLUS SDS- 5,0x 210/ 150- 4PLUS-Sika
SDS- 5,0x 260/ 200- 4PLUS SDS- 5,0x 260/ 200- 4PLUS-Sika
SDS- 5,0x 310/ 250- 4PLUS SDS- 5,0x 310/ 250- 4PLUS-Sika
SDS- 5,2x 160/ 100- 4PLUS TI-T25-6,3xL
SDS- 5,2x 210/ 150- 4PLUS
f
L
03/2012
6.6
Tools and accessories Accessories
Order information
d1 d1
L L
F F
Order code
Sarnadrill Extension 14-500 drill extension for the Sarnadrill conus drills
Sarnadrill-STOP (ZVK-STOP): The special STOP drills additionally core out the insulation providing for easy sleeve
insertion and accurate fastener alignment with the pilot hole.
Sarnadrill Extension (ZVK): Conus drills for different use, mostly to replace very long SDS drills.
All approvals and recommended design loads are based on close tolerance holes drilled with SFS intec ZVK carbide drill bits.
Order information
Order code
ZVK- 4,8x 100x 165 STOP
Type d1 L F Code Application range SFS intec
ZVK- 4,8x 100x 165 STOP SPIKE® twister DT-S-4,8xL
TI-T25-6,3xL
TIA-T25-6,3xL
ZAK- 500
ZAK- 750
03/2012
6.7
Accessories Tools and accessories
Accessories
DI 650
03/2012
6.8
Tools and accessories Accessories
Pull-out tester
Application
Pull out meter especially adapted for the measurement of pull-out Technical details
strengths of different fastener types for use in roofing, cladding and Range of application: Up to 9000 N tensile force
building applications. Grips are not included. Measuring accuracy: ± 2%
Housing material: Aluminium casting
Dimensions: Ø 220 x 300 mm
Weight: 2,6 Kilogram
Packaging: Metal case
36 x 27 x 29,5 cm
Weight with case: 5,9 Kg
Accessories
Grip LFS0250 Technical details
Range of application: Fasteners with max. shank
dia of 6,5 mm
Weight: 80 g
Material: Hardened tool steel
Surface finish: Zinc-coated
03/2012
6.9
Business Solutions flat roof
03/2012
6.10
Flat roof fastening systems
SFS unimarket AG SFS intec s.r.o. SFS intec Inc. Promtex d.o.o.
Befestigungstechnik Vesecko 500 Canada Service Center ul Kolo Srpskih Sestara 13A
Nefenstrasse 30 CZ-511 01 Turnov 40 Innovation Drive CS-21000 Novi Sad
CH-9435 Heerbrugg cz.turnov@sfsintec.biz CA-Dundas, Ontario L9H 7P3 promtex@eunet.yu
sfsunimarket@sfsunimarket.biz ca.dundas@sfsintec.biz
SFS intec Kft. Powers Fasteners
SFS intec GmbH Vásártér 18 Guangzhou SFS intec Australasia Pty Ltd.
In den Schwarzwiesen 2 HU-9241 Jànossomorja Fastening & Precision Parts Co., Ltd 5-7 Henley Court
DE-61440 Oberursel / TS hu.lanossomorja@sfsintec.biz 5/F, Bi Hua Building, AU-3189 Moorabbin VIC
de.oberursel@sfsintec.biz No. 3 JinXiu Road pdigby@powers.com.au
SFS intec Sp.z o.o. Guangzhou Development District
SFS intec GmbH ul. Torowa 6 CN-Guangzhou 510730, P.R. China Theorem Infra Solutions Pvt.Ltd.
Wiener Str. 29 PL-61-315 Poznan mcmi@sfsintec.biz B-2056, Oberoi Garden Estate,
AT-2100 Korneuburg pl.poznan@sfsintec.biz Chandivili, Andheri (East),
at.korneuburg@sfsintec.biz Tech Fasteners Ltd. Mumbai – 400 072
SFS Dekpaks Baglanti Elemenlari Unit 18-2 Clondalkin info@theoreminfra.com
SFS intec E y P, S.A. Sanayi ve Ticaret A.S. Industrial Estate
Avda. de Quitapesares 31 - Nave 15 7 Eylül Mahallesi, Celal Umur Caddesi 9 IE-Dublin 22
ES-28670 Villaviciosa de Odón TR-35860 Torbali Izmir techfast@iol.ie
es.villaviciosa@sfsintec.biz
SFS intec AS Viba N.V.
SFS intec SAS Solheimveien 44 Bleiswijkseweg 41
39 rue Georges Méliès NO-1473 Lørenskog P.O. Box 441
BP 55 no.lorenskog@sfsintec.biz NL-2712 PB Zoetermeer
FR-26902 Valence Cedex 9 viba@viba.nl
fr.valence@sfsintec.biz SFS intec AB
Olivehällsvägen 10 Dejond N.V/S.A Your international contact:
SFS intec E. y P., S.A. SE-645 42 Strängnäs Terbekehofdreef 55-59
Suc. em Portugal se.strangnas@sfsintec.biz BE-2610 Antwerpen (Wilrijk)
Rua Henrique Marques, 1E info@be.dejond.com
PT-2665-233 Malveira, Portugal SFS intec Oy
pt.malveira@sfsintec.biz Ratastie 18 EPRO d.o.o.
FI-03100 Nummela Celovska cesta 228
SFS intec Ltd. fi.nummela@sfsintec.biz SI-1000 Ljubljana
153 Kirkstall Road igor.torkar@siol.net
GB-Leeds, LS4 2AT SFS intec Inc.
gb.leeds@sfsintec.biz Spring St. & Van Reed Rd. F-Systems Ltd.
PO Box 6326 Elektrolitny pr 5B
SFS intec s.p.a. US-Wyomissing, PA 19610 RU-115230 Moscow
Via Castelfranco Veneto n.71 us.wysales@sfsintec.biz makarova@sfsintec.ru Lennard Spirig
IT-33170 Pordenone International Key Account
it.pordenone@sfsintec.biz Izolteh d.o.o. Manager, Flat Roof
XIV Podbrezje 15 spl@sfsintec.biz
HR-10010 Zagreb Tel +41 71 727 5721
izolteh@post.htnet.hr Mobile +41 79 200 19 30
03/2012
7.1
Common engagement of two innovative partners-
No compromises on safety, to ensure long term performance and quality.