Professional Documents
Culture Documents
fulu-electric FL-J2 онже hs100, hs200, IDS-Drive M402T2B
fulu-electric FL-J2 онже hs100, hs200, IDS-Drive M402T2B
Operating Instructions
properly.
■ Technical specifications of this product may change without prior
notice.
2RI20140401-2.0 VersionA
English
STATEMENT
Thanks to the use of frequency converter, before use, be sure to
safety precautions.
Safety precautions:
1、Before the connection, please confirm whether the input power is
in the power down state.
2、Connection work, please professional electrical engineering
diagram.
1 / 26
9、Do not receive the power cord to the output U, V, W terminal
10、Do not access the contactor output circuit.
11、Electricity before installing protective cover. Remove the cover,
12、Select reset to try the function of the inverter, please do not close
13、After confirming the operation signal is cut off, the alarm can be
maintenance.
17、Do not transform the inverter.
2 / 26
1、Technical Data
Converter Rated Data
Output Physical Size
Version Power Input
A ① A ② sizedimension
Long*wide*high
0.75G1-220V 0.75KW 4 3.7 ((mm)
150*115*150
single phase
1.5G1-220V 1.5KW 7 6.4 150*115*150
A.C.
2.2G1-220V 2.2KW 9.5 8.7 150*115*150
220V-240V
4.0G1-220V 4.0KW 15 14 210*118*180
50Hz/60Hz
5.5G1-220V 5.5KW 20 18 210*118*180
0.75G3-380V 0.75KW 2.5 2.3 150*115*150
1.5G3-380V 1.5KW 4.1 3.8 150*115*150
2.2G3-380V 2.2KW 5.8 5.3 150*115*150
three-phase
4.0G3-380V 4.0KW 9.4 8.6 210*118*180
A.C.
5.5G3-380V 5.5KW 12.6 11.6 210*118*180
370V-440V
7.5G3-380V 7.5KW 16.1 14.8 210*118*180
50Hz/60Hz
11G-380V 11KW 24 22 322*208*192
15G3-380V 15KW 32 30 322*208*192
18.5G3-380V 18.5KW 37 34 322*208*192
Remarks:① At rated voltage, the carrier frequency is 4,6,8kHz
R S R S T P B
+10V
+12V
ACM
AVI
CE1
CE2
CE3
STP U V W PE
AO
DO
RA
RB
RC
ON
to fault indication)
Analog output
potentiometer M
3~
0-20mA 5KΩ
4-20mA
4 / 26
PE ground connection Frequency converter to be a good grounding
Three wire system start When the three wire system is used to start
STP the frequency converter, the signal is
stop connected with the terminal.
5 / 26
3、Debugging And Running
① Operation Panel And Operation Method
Run key
Press the running key, and
the converter starts to run
n
utto
ow b
yell
s the
Pres
Pres
s th
e ye
llo w bu
tto n
After setting the parameters, return to
the original interface method:
择
6 / 26
② Frequency Setting Mode Selection
The frequency setting mode of frequency converter is set by the parameter C01. C01=0, the
operating frequency is set by the potentiometer or multi speed setting; C01=1, the operating
frequency is set by the parameter F40.
(1) C01=0, potentiometer setting:
Potentiometer setting panel potentiometer or terminals of an external potentiometer, selected
by the terminal in the upper left corner of the toggle switch B1 (to the left of the toggle switch),
to dial selection panel potentiometer, pulled downward to the terminal of an external
potentiometer.
7 / 26
③ Frequency converter start mode setting
There are several ways to start the frequency converter: panel control start stop, terminal
forward (FWD) reverse (REV) start, terminal rotation direction control, three wire system start
and stop control. The following are introduced:
panel control start and stop: (factory set to panel start stop)
To use the panel to control the start and stop frequency converter, the toggle switch B2
(pictured on the right side of the switch to dial up wave). Connect 12V and ON after (must be
connected to boot), press the green button on the panel to start, red button down. Note: the
use of panels to control the start and stop, must be parameters CE1=6.
(4) outside the green button to start, red button down (three wire system start
stop):
Green button is normally open or compound switch, the red button is often closed, that
cause the frequency converter bus voltage rise, the inverter will report dEC alarm or OU fault.
This situation requires the installation of brake resistance. General deceleration time required
Brake resistance and power according to the selection table selection. The brake resistor
down.
The first step: in the parameter C36 set DC brake pressure, the specific value according to
The third step: in the inverter deceleration, on 12V and CE3, it will be applied to DC brake.
4、Parameter Table
Factory Setting
NO. name notes
value range
Only when the password
Login
C00 0 0-999 function is valid can be seen
password
(see C94)
0:AVI analog Can be selected by the wave
input.C37,C38, switch B1, set by the panel
C39 multi potentiometer or by the
Frequency
C01 0 speed input terminal AVI。
command
1: parameter The frequency command is
F40 setting set by the value of the
frequency parameter F40.
9 / 26
0: restore If the original C02=1, first
completed changed to 0, and then
C02 factory reset 0 changed to 1, you can reset.
1: restore the
(to remove the 12V and ON
factory value
between the short connection)
1: uses multi At the same time, the multi
speed 1, C37 segment speed 1 and the
2: uses multi multi speed 2 signals are
speed 2, C38 switched on, and the
3: start DC frequency is operated in
DC brake voltage
accordance setmulti
with the by C36
brake
section speed 3.
4: rotation Disconnect: forward turn; turn
direction on: reverse
selection
5: frequency On: start up operation;
converter start disconnect: deceleration stop;
Digital input operation
6: positive Choose 6 when the switch is
CE1 6
CE1 transfer option turned on.
(FWD)
7: reverse Choose 7 when the switch is
selection (REV) turned on, the reverse start,
8:UP (ramp
generator) UP off, DOWN off, slow down
9:DOWN (ramp stop.
generator)
10: external Disconnect the trigger fault
fault shutdown (normally closed signal)
Factory
NO. name Setting range notes
value
10 / 26
2: motor
Motor operated relay
operation
3: the motor is Motor relay with positive
turning rotation
4: motor
Motor reversing action relay
reverse
The frequency converter
5: the output
output frequency is 0 when the
frequency is 0
action relay
6: the Output frequency to reach a
frequency to given value (AVI given or
reach a given given by F40)
7: the
value The output frequency reaches
frequency of
the value of the C17 set.
arrival
8: reach the The output current reaches
current limit the limit value of C22
V/F:Standard application
0: with automatic
V/F two party: applied to
voltage to
C14 control mode 2 the fan pump class
enhance the V/F
curve
11 / 26
1: with automatic
voltage to
enhance the V/F
two square curve
2: with a constant
voltage to
enhance the V/F
C15: according to the rated
curve
frequency of the motor
3: with a constant nameplate on the set
voltage to C16: this setting is mainly
enhance the V/F used to improve the torque at
two square curve low speed
V/F rated
C15 50.0 25.0-500 Hz
frequency
Constant lifting
C16 4.0 0-40 %
voltage
output C08=7, the output frequency
C17 frequency 0.0 0.0-500 Hz reaches this value, the relay
Preset value action
0: 4kHz When the operating current to
carrier 1: 6kHz the rated current of 1.2 times,
C18 2
frequency 2: 8kHz the carrier frequency will be
3: 10kHz reduced to 4kHz
Slip Adjust this parameter until the
C21 compensation 0.0 0.0-40.0 %
motor does not stall
value
When the output current
reaches the limit value, the
Output current 30-150% rated
C22 150 deceleration time becomes
limit output current
longer or the output frequency
becomes lower.
12 / 26
Factory Setting
NO. name notes
value range
0:0…10V
1:0…5V
Signal
C34 0 2 : 0 … Set the type of AVI signal input
type
20mA
3 : 4 …
20mA
When the value of CE1, CE2 and
DC brake 0.0-50.0
C36 4.0 CE3 is equal to 3, the DC
voltage %
braking.
Multi speed 0.0-500
C37 20.0
1 Hz
By setting the value of CE1, CE2,
Multi speed 0.0-500
C38 30.0 CE3, to select multi segment
2 Hz
speed operation.
Multi speed 0.0-500
C39 40.0
3 Hz
Display
0.0-500 Displays the current frequency of
C46 frequency
Hz a given value
for a given
value
Display
0.0-500
C50 output Display current output frequency
Hz
frequency
Display DC
Shows the current DC bus
C53 bus voltage 0-255 %
voltage percentage
frequency
Display
C54 motor 0-255 % Display current motor output current
current
Automatically identifying the voltage
0:automatic
of the input power supply
Power input
C90 voltage 1 1:low Power set to low input 220V or 380V
selection
Power set for high input 240V or
2:high
450V
13 / 26
When the password is not set to 0,
User
C94 0 0-999 you must enter the password in the
password
C00 to access the parameters
Factory
NO. name Setting range notes
value
14 / 26
8 : Reach current The output current reaches the limit
limit value of C22
Motor thermal 30-100%, 100% is Note: the maximum set is the motor
F20 protection 100 the rated output rated current, but can not provide full
setting current protection.
Set running
F40 frequency 50 0.0-500 Hz Only C01=1, this setting is valid
setting value
Factory
NO. name Setting range notes
value
Display fault
F62 Final fault Only for display
information
Display fault
F63 Last fault Only for display
information
0: re on the power,
the terminal ON plus Both of these 3 methods can reset
Fault reset a low level, digital the fault
F70 0
mode input is set to 11
1: automatic fault
Automatic reset after F71
reset
Fault auto
F71 0 0.0-60.0 s Delay time of fault auto reset
reset delay
15 / 26
2 : Enable PID
positive
feedback control
Display the
set value of Displays the set value of the actual
F38 F86-F87
the PID PID control
control
Minimum
F86 0.0 0.0-999 Using the parameter C34 to select
feedback
the signal type of the feedback
Maximum
F87 100 0.0-999 value. Must F86 < F87
feedback
Under voltage The main power supply Check the power supply voltage
alarm voltage is too low and parameters C90
16 / 26
Deceleration time is too If over voltage <1s, then
DC bus
short, resulting in DC bus automatic recovery; if >1s, then
overvoltage (alarm)
voltage is too high the report OU
The frequency converter
Unable to access can not modify the Disconnect the connection
parameters parameters of the between 12V and ON.
operation
State
Meaning Reason Elimination Measures
Display
Digital input is set to 10,
External fault Exclude external faults
but not Connect
17 / 26
Cable capacitive current is Whether the motor line is too
too large long
③ Display on power up
18 / 26
Check CE1, CE2, CE3 parameter settings, does not allow to set the same value
④ Run display
If after the operation immediately display the fault information, first remove the motor line, and try
again. If remove the motor line also show fault is the inverter fault, if no longer display fault is output line
the leakage current, resulting in leakage protection switch trip, which is determined by the principle of
the frequency converter, is inevitable, when the jump occurs leakage fault is guaranteed, take the
following measures:
First: the use of leakage protection of current leakage protection of more than 200mA.
Second: modify the carrier frequency, parameter C18=0, reduce leakage flow.
Fourth: as far as possible to reduce the length of the motor line, or overhead motor line.
6、 Application examples
The electric contact pressure gauge pressure control, only need to connect the two wires, a root from
green needles, a root from black needle, respectively, then the three binding posts of the electric
contact pressure gauge above 2 (some of the electric contact pressure gauge may be different). When
19 / 26
the water pressure is low, the black needle is below the green needle, and the frequency converter is in
an accelerating starting state. When the water pressure is high, the black needle is in the green needle.
(1)2 lines from the electric contact pressure meter, a wire connected to the 12V, the other line is
connected to the CE1 (no need to distinguish between positive and negative).
(2)On the right side of the wave switch B2 dial to the bottom (to participate in the P6 page), select the
Automatic start up after power up. If not start, can be directly connected to the CE1 and 12V wire, to
see whether or not to start, such as can not be started, the inverter is set to explain the problem. If you
can start, that is the external electric contact table or line problems, can check whether the 2 wires on
the electrical contacts, black needle lower than the green needle should lead, black needle is higher
20 / 26
C71=0.2, I value parameter adjustment, the greater the I value, the slower the adjustment.
Recommended (0.1-1)
and the current signal. The voltage signal is connected with the ACM, AVI and 10V. If the 2 wire
pressure sensor is connected to the AVI, ACM. You can see the size of the feedback value in the
parameter C59.
21 / 26
3、Parameter setting: CE1=6, CE2=7, CE3=1, C37=10 (reverse running speed 10HZ)
22 / 26
Parameter modification record
23 / 26
Service delivery value, quality cast brilliant
Letter to the user:
Thank you for using our products, in order to ensure that you get the best
after-sales service of our company, please read the following terms, and do a
good job in the relevant matters.
1, product warranty
According to the normal use of the use of the case, the failure occurred
within the warranty.
2, product warranty period
The warranty period of this product is from the date of the factory, within
twelve months. After the warranty period, the implementation of long-term
technical support services.
24 / 26
3, non warranty scope
Any violations of the requirements of human factors, natural disasters or
water, external damage, harsh environment causes damage, and not permitted
without the transducer disassembly, modification and maintenance of behavior,
considered as a waiver of warranty service.
4, from the middle of the purchase of products
Where the dealer, agents to buy products from the user, in the product
failure, please contact the dealer or agent.
Please keep this manual in order to prepare for the use of.
25 / 26