Professional Documents
Culture Documents
Hilti Catalogue
Hilti Catalogue
RELIABILITY
Systems with long lasting performance assured by 2 years and 1 year
full service cover on qualifying tools. Testing on other systems.
SUPPORT
Deal direct with the manufacturer, national coverage
and site based support.
INNOVATION
New building methods developed as a
result of close contact with users.
PRODUCTIVITY
Faster, easier to use systems.
Accessories
Order description Item no.
PDA 80 charging set 282393
For all EU countries; from mains and vehicle charging; packed complete in cardboard box.
PDA 81 charging set 282394
PDA 80
For all non-EU countries; from mains and vehicle charging; packed complete in cardboard box.
PDA 50 target plate 282388
For extended ranges and exterior measurements PA 450
PDA 62 belt clip 282391
For clicking the laser range meter to the belt.
PDA 70 spike extension 282392 PDA 81
For comfortable measurements from the floor and from inaccessible places
PA 970 laser visibility glasses 311212
PA 940
Improves the laser visibility significantly.
PA 450 tripod adaptor 337829
tripod head adaptor for the PD 30/PD 32 PA 920
2
Measuring systems
PS 200 Ferroscan
Portable Steel Reinforcement Detection System
Applications
Verification of reinforcement: locate rebar when plans are not at
hand, for acceptance inspectations, before structural repair or
change of loads on a structure.
Verification of concrete cover over reinforcement: Obtain concrete
cover information over large areas for acceptance inspections,
before renovation, or for quality control.
Avoiding rebar hits: Avoid cutting through critical reinforcement
or costly rebar hits.
Detection range and accuracy (mm)
Imagescan
Depth
20 40 60 80 100 120 140 160 180
6 ±2 ±3 ±3 ±4 ±5 0 x x x
8 ±2 ±3 ±3 ±4 ±5 0 0 x x
10 ±2 ±3 ±3 ±4 ±5 0 0 x x
12 ±2 ±3 ±3 ±4 ±5 ±10 0 x x
Bar Diameter
14 ±2 ±3 ±3 ±4 ±5 ±10 0 0 x
16 ±2 ±3 ±3 ±4 ±5 ±10 0 0 x
20 ±2 ±3 ±3 ±4 ±5 ±10 ±11.5 0 x
25 ±2 ±3 ±3 ±4 ±5 ±10 ±11.5 0 x
28 ±2 ±3 ±3 ±4 ±5 ±10 ±11.5 0 x
30 ±2 ±3 ±3 ±4 ±5 ±10 ±11.5 0 x
36 ±2 ±3 ±3 ±4 ±5 ±10 ±11.5 ±13 x
Bar diameter given. Value indicates accuracy of depth measurement in mm.
0 - bar can be detected at this depth but no depth calculated
X - bar cannot be detected at this depth Benefits
Valid for bars conforming to DIN 488
Immediate high resolution image for a clear picture of the rein-
Quickscan recording (mm) forcement.
Depth Determine bar depth and estimate diameter at any point on
20 40 60 80 100
the image.
6 ±2 ±3 ±3 ±4 ±5
Determine average concrete cover over large areas easily.
Reduce wear on drill/core bits and tool motors when drilling
8 ±2 ±3 ±3 ±4 ±5
through reinforcement.
10 ±2 ±3 ±3 ±4 ±5 Reduce drilling times - important in repetitive drilling applica-
12 ±2 ±3 ±3 ±4 ±5 tions.
Bar Diameter
Bar diameter given. Value indicates accuracy of depth measurement in mm. PS 200 Ferroscan System 377645
0 - bar can be detected at this depth but no depth calculated PS 200 S Scanner 377652
X - bar cannot be detected at this depth PS 200 M Monitor 378029
Valid for bars conforming to DIN 488 PUA 80 Charger 377458
Technical data
Scanner Memory Capacity : Up to 9 Image scans plus up to 30 m of recorded Quickscan
Monitor Memory Capacity/Type : 32 MB Removable Multimedia Card (150 Images or 75 Quickscans)
Battery Life : Typ. 8 hour
Protection Class : IP 54 as per IEC529
Operating Temperature Range : -10 °C to +50 °C
Scanner Dimensions / Weight : 229x132x132 mm / 1.4 kg
Monitor Dimensions / Weight : 264x152x57 mm / 1.4 kg
Minimum System Requirements for PC Software : Microsoft®Windows®98, 16 MB RAM, 8 MB free hard disk space,
CD-ROM Drive, USB v1.1 interface.
3
Drilling and chiselling systems
4
Drilling and chiselling systems
Rotary hammer drill TE 2
A special light weight hammer drill for
anchor holes in concrete and masonry
Technical data
Power input : 600 W
Single impact energy : 1.8 Joules
Speed under load : 0-930 r.p.m.
Hammering speed under load : 0-4600 blows/min.
Dimensions : 344x200x79 mm
Weight : 2.3 kg
Drilling performance in medium-hard
concrete with 8 mm dia. drill bit : 500 mm/min.
Ordering designation Item no.
TE 2 230 V 336793
Includes TE 2 rotary hammer complete with side handle, depth gauge, dust
shield, impact resistant plastic tool case and operating instruction.
5
Drilling and chiselling systems
Rotary hammer drill TE 6-S
The light rotary hammer with variable
hammering action
Technical data
Power input : 600 W
Single impact energy, full hammering : 1.8 Joules
Single impact energy, fine hammering : 0.6 Joules
Speed under load : 0-880 r.p.m.
Hammering speed, full hammering : 0-5100 blows/min.
Hammering speed, fine hammering : 0-2700 blows/min.
Dimensions : 320x215x75 mm
Weight : 2.8 kg
Drilling performance in medium-hard
concrete with 8/12/16 mm dia. : 550/400/240 mm/min.
Ordering designation Item no.
TE 6-S 230 V 369023
TE 6-S+DRS 230V 369023
Includes TE 6-S rotary hammer complete with side handle, depth gauge,
dust shield, impact resistant plastic tool case and operating instruction.
6
Drilling and chiselling systems
Technical data
Power input : 375 W
Nominal battery voltage : 36 V
Energy capacity : 86 Wh
Single impact energy : 1.5 Joules
Speed under load : 0-890 r.p.m.
Hammering speed under load : 0-5000 blows/min.
Dimensions : 330x225x100 mm
Weight with battery / with belt adapter : 4.7 kg / 2.8 kg
Technical data
Power input : 830 W
Single impact energy : 3.8 Joules
Speed under load 1st speed: 0-310 r.p.m.
2nd speed: 0-640 r.p.m.
Hammering speed under load : 0-3720 blows/min.
Dimensions : 440x220x100 mm
Weight : 4.9 kg
Supply cord length : 4m
Ordering designation Item no.
TE 25 230 V 308327
Includes TE 25 rotary hammer complete with side handle, depth gauge,
dust shield, impact resistant plastic tool case and operating instruction.
7
Drilling and chiselling systems
8
Drilling and chiselling systems
Accessories
Accessories for TE 2
Quick-release chuck
For cylindrical shank twist drills up to 13 mm diameter for drilling without hammering
Ordering designation Item no.
Quick-release chuck 13 60208
Chuck spindle TE-C-BFH 60459
Accessories for TE 25
Special chuck for twist drills with cylindrical shank up to 13 mm diameter for
drilling without hammering
Ordering designation Item no.
Quick-release chuck 30201
9
Drilling and chiselling systems
Combihammer TE 56
Innovative lightweight combihammer
Technical data
Power input : 1100 W
Single impact energy : 100% : 7.0 J/ 50% : 3.5 J
Speed under load : power level I : 0-480 r.p.m.
power level II : 0-720 r.p.m. (ATC)
Hammering speed under load : 0-2886 blows/min.
Dimensions (LxWxH) : 475x240x95 mm
Weight : TE 56 : 5.9 kg
Drilling performance in
medium-hard concrete with 20 mm dia. : 350 mm/min.
Combihammer TE 76 / TE 76-ATC
Megapower with revolutionary
operator protection
Technical data
Power input : 1300 W
Single impact energy : 100% : 8.3 J / 50% : 4.2 J
Hammering speed under load : 0-2770 blows/min.
Speed under load : Power level I 0-200 r.p.m.
Power level II 0-282 r.p.m.
Dimensions : TE 76 497x261x115 mm
TE 76-ATC 510x288x115 mm
Weight : TE 76 7.0 kg
TE 76-ATC 7.9 kg
Drilling performance 20 mm dia.: 360 mm/min.
in medium-hard concrete 25 mm dia.: 290 mm/min.
32 mm dia.: 180 mm/min. operates in addition
Chiselling performance to the mechanical slip clutch:
into medium-hard concrete 575 cm3/min. Sensors detect jamming of the drill
Ordering designation Item no. bit, the control unit will
TE 76 230 V 334506 disengage the magnetic clutch
TE 76-ATC 230 V 334510
immediately and shut off the
Includes TE 76 complete with side handle, depth gauge, dust shield,
Hilti grease, cleaning cloth, impact resistant plastic tool case and motor.
operating instruction.
Chuck adapter
Ordering designation Item no.
TE-FY-BA-C 74068
for TE-C drill bits
10
Drilling and chiselling systems
Dia. Working Ordering designation Item no. Dia. Working Ordering designation Item no.
(mm) length (mm) (mm) length (mm)
Dia. Working Ordering designation Item no. Dia. Working Ordering designation Item no.
(mm) length (mm) (mm) length (mm)
11
Drilling and chiselling systems
12
Drilling and chiselling systems
Breaker TE 705
For powerful chiselling
Applications
Making breaches, demolition work and corrective work towards
a wall; ideal for building renovation work, repairs and plumbing
installations
Working on surfaces and precision work
Technical data
Power input : 1030 W
Single impact energy : 4.3 / 8.5 Joules
Hammering speed under load : 1890 / 2670 blows/min.
Dimensions : 515x115x215 mm
Weight : 6.5 kg
Chiselling performance in
medium-hard concrete : 500 cm3/min.
Ordering designation Item no.
TE 705 230 V 313268
Includes TE 705 complete with side handle, Hilti grease, cleaning cloth,
impact resistant plastic tool case and operating instruction.
Breaker TE 805
Powerful, portable and reliable
Applications
Removal and demolition work with concrete, masonry, stone
and asphalt
Technical data
Power input : 1350 W
Single impact energy : 17 Joules
Hammering speed under load : 2000 blows/min.
Dimensions : 590x122x230 mm
Weight : 9.7 kg
Chiselling performance in
medium-hard concrete : 1200 cm3/min.
Ordering designation Item no.
TE 805 230 V 255166
Includes TE 805 complete with side handle, Hilti grease, cleaning cloth,
impact resistant plastic tool case and operating instruction.
13
Drilling and chiselling systems
Total length (mm) Blade width (mm) Ordering designation Item no.
Pointed chisel
Overall length (mm) Ordering designation Item no.
Flat chisel
Overall length (mm) Cutting edge width(mm) Ordering designation Item no.
Wide-flat chisel
Overall length (mm) Cutting edge width(mm) Ordering designation Item no.
14
Diamond systems
1
Ordering designation Item no.
15
Diamond systems
Applications
Precision holes in reinforced concrete, natural stone, masonry and
asphalt; for cables, pipes, ventilation, test cores and anchors
Advantages of motor unit
Can be used both handheld and on a rig
Can be used for both wet and dry diamond coring without
modification
Safety features include: safety slip clutch; ground fault interrupter
(PRCD), electronic speed regulator; overload current regulator
and integrated starting current regulator; thermal motor protector
Easy to use and understand
Leveling bubble for accurate hole-starting
Quick-lock connection end for fast insert and removal of core bits
Compatible with innovative Hilti DD-B and PCD core bits
Advantages of drill stand
Comfortable drilling posture maintained throughout coring process
Quick-lock motor mount mechanism for simplicity and speed Feature
Cores at angles up to 45 degrees quickly and easily and without
Wet and dry for more
the need for any additional tools flexibility
Suitable for anchor, vacuum and brace fastening without any The Hilti DD 130 can be used
modification or alteration for wet or dry drilling in a
Provides easy access for coring in corners and against walls wide variety of materials
without the need for any
modification or change of
Technical data parts.
Voltage : 230 V
Nominal power : 1900 W
Nominal current : 8.7 A
Weight : DD 130 tool 7.7 kg
DD 130 rig 13 kg
Speed (no load)/Diameter range :
wet 1st gear 780 r.p.m. 57-152 mm
2nd gear 1400 r.p.m. 28-52 mm
3rd gear 2600 r.p.m. 12-25 mm
dry 1st gear 780 r.p.m. 122-162 mm
2nd gear 1400 r.p.m. 67-122 mm
3rd gear 2600 r.p.m. 12-62 mm
Chuck type : Quick-release BI+
Min. access to walls : 40 mm from the center of the hole
Min. access to corners : 57 mm from the center of the hole
Max. stroke (stationary) : 430 mm
DD 130 Tool
Ordering designation Item no.
DD 130 Rig
Ordering designation Item no.
16
Diamond systems
Technical data
Voltage : 230 V
Power : 2400 W
Current : 11 A
No-load speed : Core bit diameter range
1st speed : 275 r.p.m. 172-250 mm
2nd speed : 450 r.p.m. 92-102 mm
3rd speed : 950 r.p.m. 40-102 mm
4th speed : 1800 r.p.m. 25-56 mm
Weight : 17 kg
17
Diamond systems
Quicker
Coring up to 70 percent faster than comparable core bits.
Retipping of worn 35 to 250 mm diameter core bits in only 20
minutes with the unique Hilti change module.
Stronger
Laser-welded diamond segments ensure maximised joint quality
for a 30 percent stronger hold than conventionally brazed
segments.
Cutting-edge manufacturing processes guarantee top quality and
long life expectancy of each core bit.
Simple
Quick connection ends (BI+ and BU)
ensure a simple core bit change without
the use of a tool, and optimise power
The more reinforcement in concrete, the better the performance. The transmission.
new Hilti DD-B series cut through rebars up to 70 percent faster.
Power Flexible
Due to the innovative diamond matrix, coring You can drill through many grades of
is amazingly quick and the life expectancy reinforced concrete, marble, sandstone,
extremely long. Laser-welded diamond natural stone and tiles using one core bit
segments give you the assurance of top joint throughout.
quality.
P2 core bit: For concrete of low to medium abrasiveness, natural stone and clinker. Concrete with medium to low reinforcement content.
P4 core bit: For concrete of medium to high abrasiveness and brick. Concrete with medium to high reinforcement content.
P6 core bit: For concrete high abrasiveness. Concrete with flint aggregates.
P130 core bit: For DD 130 diameter 102-152 mm.
18
Diamond systems
* See details of P2, P4, P6, P130 core bits specifications on page 18
19
Diamond systems
Clean old brazing alloy off interface using Obtain optimal brazed joint by coating cut Heat up flux with brazing torch and braze
wire brush. surface and change module with flux on new change module.
(available from Hilti warehouse).
* See details of P2, P4, P6, P130 core bits specifications on page 18
20
Diamond systems
Hilti DG 150 diamond grinding system
Revolutionary dry diamond grinding system for exceptionally
high material removal performance and long life expectancy.
Keeps dust to an absolute minimum thanks to the specially developed
dust hood and new Hilti VCD 50 dry vacuum cleaner
Maximum material removal thanks to finetuned diamond cup
wheels for every application
New SR motor technology for long life
Applications
Dry grinding coated and uncoated mineral materials
- removal of remains of coatings and tile adhesives on floors and
balconies
- high rate of removal and perfect finish on concrete and screed
- removal of thin paint coating on hard cement rendering
Technical data (DG 150 with DPC 20)
Nominal voltage 230 V
Nominal current 8.8 A
Power input 2100 W
Power output 1500 W DG 150 diamond grinder
No-load speed
Ordering designation Item no.
Setting no. 1 4700 r.p.m.
Setting no. 2 6600 r.p.m. DG 150 diamond grinding system, 230 V complete 369391
Weight (without DPC 20) 4.1 kg Includes DG 150 with DPC20 in Hilti toolbox, with 1 pair of
Cup wheel diameter 150 mm dia. goggles,
Electrical protection Protection class II 1 wrench, 1 clamping flange, 1 clamping screw (M13),
(double insulated) 1 operating instructions
Quick stop in two seconds or less after switching off,
restart interlock, adjustable grip, dust hood with opening
section and adjustable in height
Filter insert
21
Diamond systems
Convenient controls
Digital remote control for greater
convenience, safety and efficiency
Operating status indicators
Fault indicators
For all applications
Powerful drive
Compact saw head
Saw arm with built-in hydraulic motor
Central cooling water supply for motor
and saw blade
Saw arm with synchronised blade
guard pivots 360 in both directions
Intelligent advance
HTC for maximum power
transmission and highest cutting
performance
Semi-automatic advance,
independent of the material being cut
Cam-action roller system for rapid
saw head mounting
22
Diamond systems
DS-BG blade guard for normal / corner cutting
Ordering designation Accessory Qty. Item no.
TS30 TS32
DS-BG 8* blade guard 1 370474
DS-BG 9* blade guard 1 370476
DS-BG 10* blade guard 1 370477
DS-BG 12* blade guard 1 370478
DS-BG 16* blade guard 1 333883
*Corresponds to maximum saw blade diameter (x100)
HI CM-H specification for normal speed with long life in reinforced concrete with a high amount of quart sand
Diameter Segment Segment Segment No. of Ordering Item no.
(mm) width (mm) height (mm) length (mm) segments designation
600 4.5 10 50 31 DS-B 600/HI CM-H 339822
700 4.5 10 50 37 DS-B 700/HI CM-H 339823
750 4.5 10 50 39 DS-B 750/HI CM-H 339824
800 4.5 10 50 42 DS-B 800/HI CM-H 339825
800 5 10 50 42 DS-B 800/5/HI CM-H 339826
900 4.5 10 50 47 DS-B 900/HI CM-H 339827
1000 4.5 10 50 50 DS-B 1000/HI CM-H 339828
1200 4.5 8 50 58 DS-B 1200/HI CM-H 339829
HI CH-H specification for normal speed with long life in reinforced concrete Mounting bore and
drive screw spacing
with hard aggregate and high abrasiveness Standard version: 6 countersunk holes for
flush-cutting
Diameter Segment Segment Segment No. of Ordering Item no. (suitable for use with the
(mm) width (mm) height (mm) length (mm) segments designation Hilti DS-FCA-110
600 4.5 10 50 31 DS-B 600/HI CH-H 374074 flush-cutting flange and
DL-FA 30-110)
800 4.5 10 50 42 DS-B 800/HI CH-H 374075 Other versions: Available to order
900 4.5 10 50 47 DS-B 900/HI CH-H 374076
1000 4.5 10 50 50 DS-B 1000/HI CH-H 374077 Ø110
23
Direct fastening systems
Features:
Automatic cartridge feed, thus no
wasted cartridges
Electrical installation clamps/clips: Universal piston
lamps, lighting, conduits
Simple cleaning and servicing
24
Direct fastening systems
DX 460 Powder-actuated fastening tool
Technical data
Weight : 3.53 kg incl.magazine
Length : 460 mm
Magazine capacity : nails in magazine
strips of 10
lengths 14-72 mm
Cartridge : 6.8/11 M, in magazine
strips of 10, 4 power levels
(green, yellow, red, black)
X-460-B X-460-STAB
25
Direct fastening systems
GX-100
X-100 SL
X-GM 40
X-100 TN
26
Direct fastening systems
6.8/11 M white Extra Light 100 333318 Ordering designation Package Item no.
contents
6.8/11 M green Light 100 50351
6.8/11 M yellow Medium 100 50352 X-EDNI 12 P8 100 34345
6.8/11 M red Heavy 100 50353 X-EDNI 16 P8 100 34536
X-EDNI 19 P8 100 34537
X-EDNI 22 P8 100 34538
X-CF Nail
Fastening to concrete up to 300 ksc for DX 460, NK Nail
DX-A40, DX-A41 Fastening to concrete for DX 450
shank dia. 3.5 mm shank dia. 3.7 mm
GN 27MX
GN 32MX GN 39MX
27
Direct fastening systems
X-CRM8-9-12P8 X-CRM8-15-12P8
28
Anchoring systems
29
Anchoring systems
HIT-HY 150
Injection adhesive
Use
Concrete
Various fastener options
HAS and HIS-N anchor rods
Rebars (not in Hilti product range)
Ordering designation Package contents Item no.
°C tgel tcure
-5 90 min 6 hours
0 45 min 3 hours
+5 25 min 1.5 hours
+20 6 min 50 min
+30 4 min 40 min
+40 2 min 30 min
The foil pack temperature must be at least +5°C.
Basic loading data (for a single anchor) : HIT-HY 150 with HAS,
HAS-E rod
HIT-HY 150 with HAS rod Recommended load, Lrec [kN]: concrete fck,cube = 25 N/mm2
Setting details
Jumbo pack
Poil pack
Setting operations
Drill hole. Clean hole. Inject mortar. Insert rod. Wait for curing. Apply tightening
torque.
30
Anchoring systems
Condition:
Concrete strength (Cylinder) : fck (Not less than 20 N/mm2) = 20 N/mm2 (~200 ksc)
Rebar yield strength (SD40) : fyk = 400 N/mm2 (~4000 ksc)
Partial safety factor: Steel = 1.15
Concrete/HY 150 = 1.5
Variable action = 1.5
Note: Contact Hilti engineering for exact calculation of your specific application.
Setting operations
31
Anchoring systems
HIT-RE 500
Injection adhesive
Use
Concrete
Natural stone
Features
Various fastener options injection system with high loading capacity
Large diameter, deeply-set rebars good performance in diamond drilled hole
(rebars not in Hilti product range) good performance in water saturated
HAS and HIS-N anchor rods concrete
Ordering designation Package contents Item no. larger diameter application
long working time at elevated temperatures
Foil pack HIT-RE 500/330/1 1 330ml 337109
odourless mortar
Foil pack HIT-RE 500/500/1 1 500ml 369109 no expansion forces in base material
Jumbo pack HIT-RE 500/1100/1 1 1100ml 337110
small edge distance and anchor spacing
clean and easy handling
Basic loading data (for a single anchor) : HIT-RE 500 with
HAS, HAS-E rod Temperature of the Working time in which Curing time before anchor
steel grade 5.8 for M8-M24 sizes and steel grade 8.8 for base material: anchor can be inserted can be fully loaded
and adjusted
M27-M39
40 cí 12 min. 4 hours
Recommended load, Lrec [kN]: concrete fck,cube = 25 N/mm2 30 cí 20 min. 8 hours
20 cí 30 min. 12 hours
10 cí 2 hours 24 hours
0 cí 3 hours 50 hours
Note: Edge distance, spacing and other influences are not -5 cí 4 hours 72 hours
considered. Contact Hilti engineering for exact calculation
of your specific application.
Iess than -5 cí Contact your Hilti advisory service.
The foil pack temperature must be at least +10 cí
HIT-RE 500 with HAS rod
Setting details
Setting operations
Drill hole. Clean hole. Clean hole. Insert foil pack Screw on
into holder. mixer.
Put cartridge Throw away first Release Inject adhesive. Insert anchor. Wait for curing. Apply tightening
into dispenser. three trigger pulls. dispenser. torque.
32
Anchoring systems
Condition:
Concrete strength (Cylinder) : fck = 20 N/mm2 (~200 ksc)
Steel strength (SD40) : fyk = 400 N/mm2 (~4000 ksc)
Partial safety factor: Steel, ;s = 1.15
Bond strength, ;b = 2.16
Concrete, ;c = 1.5
Variable actions, ;Q = 1.4
Note: Contact Hilti engineering for exact calculation for your specific application.
Setting operations
33
Anchoring systems
HIS-N Internally threaded sleeve anchor HIS-RN Internally threaded sleeve an-
Carbon steel galvanised to min. 5 microns. chor
Stainless steel A4-70 / SS316
Ordering Sleeve Thread length Hole Use with: Item no. Ordering Sleeve Thread length Hole Use with: Item no.
designation length (mm) (mm) dia.(mm) designation length (mm) (mm) dia.(mm)
HIS-N M 8x90 90 8-20 14 HVU M10 258015 HIS-RN M 8x90 90 8-20 14 HVU M10 258024
HIS-N M10x110 110 10-25 18 HVU M12 258016 HIS-RN M10x110 110 10-25 18 HVU M12 258025
HIS-N M12x125 125 12-30 22 HVU M16 258017 HIS-RN M12x125 125 12-30 22 HVU M16 258026
HIS-N M16x170 170 16-40 28 HVU M20 258018 HIS-RN M16x170 170 16-40 28 HVU M20 258027
HIS-N M20x205 205 20-50 32 HVU M24 258019 HIS-RN M20x205 205 20-50 32 HVU M24 258028
34
Anchoring systems
Base material
Concrete
Hard natural stone
Use
Heavy-duty fastenings with small spacing and edge distance
System
Consisting of adhesive in a foil capsule and an anchor rod or
internally threaded sleeve
Setting operations
Features
A strong foil capsule
Adapts flexibly to fit in irregular holes
Capsules do not drop out of overhead holes
35
Anchoring systems
Basic loading data (for a single anchor) : HVU capsule with HAS, HAS-E
steel grade 5.8 for M8-M24 sizes and steel grade 8.8 for M27-M39
Note: Edge distance, spacing and other influences are not considered.
Contact Hilti engineering for exact calculation of your specific application.
Setting details
36
Anchoring systems
Tension Fatigue Shock Seismic Close edge Performance Fire Hilti Nuclear
Concrete zone distance/ of a headed resistance power plant
Anchor
spacing stud (F 180) programme approval
Simply reliable
Heavy-duty fastenings
High loads combined with small edge distance and spacing
Dynamic loading, e.g. fatigue, seismic or shock
Extreme shear loading
Immediate loading capacity after setting
Easy removal
Material
Steel grade 8.8, galvanised to min. 5 microns Fastenings subjected to high shear and dynamic loads
HDA-P Anchor for pre-setting Basic loading data (for a single anchor) : HDA-P
37
Anchoring systems
Setting details
Setting operations
38
Anchoring systems
Features
suitable for the tension zone
high loading capacity
force-controlled expansion
reliable pull-down of part fastened
no rotation in hole when tightening bolt
Features
Material Integrated plastic section:
Steel grade 8.8, galvanised to min. 5 microns - to avoid turning in the hole
- to telescope and pull down
39
Anchoring systems
Note : Edge distance, spacing and other influences are not considered.
Contact Hilti engineering for exact calculation of your specific application.
Setting details
Setting operations
Drill hole. Blow out dust and Install anchor. Apply tightening torque
fragments (for HSL-B, no torque
wrench is needed).
40
Anchoring systems
Small
edge Corrosion Fire resistance Hilti Anchor
Concrete Tension zone Shock resistance +hydrocarbon programme
distance / curve
spacing
Features
Complete system
Keying hold
Shallow anchorage depth
Low expansion force (thus small edge distance/spacing)
Automatic undercutting (without special undercutting tool)
Mark on anchor for setting control (easy and safe)
Anchorage depth mark on sleeve
Suitable for tensile zone Features
Anchor hole drilled as usual,
Material without undercutting
Steel grade 8.8, galvanised to min. 5 microns Automatic undercutting by
anchor when anchor sleeve is
driven onto stud taper
Fire resistance
HSC-A : external thread version Basic loading data (for a single anchor) : HSC-A
HSC-I : internal thread version Basic loading data (for a single anchor) : HSC-I
41
Anchoring systems
Stop bit for exact hole depth Setting tool for automatic undercut
Hole HSC-A HSC-I Ordering Item no. External thread Internal thread Ordering Item no.
dia. (mm) designation designation
Setting details
HSC-A/-AR HSC-I/-IR
M 12x60
M 10x50
M 10x60
M 12x60
M 8x40
M 8x50
M 6x40
M 8x40
Setting Details
h [mm] Min. base material thickness 100 100 100 130 100 110 130 130
Drill bit TE-C B- 14x40 14x50 16x40 18x60 14x40 16x40 18x50 18x60 20x60
Check setting
of type A
anchor
Drill hole with stop Blow out dust and Insert type A anchor Set with setting tool. Secure part being
drill bit. fragments. into hole. fastened.
Check setting
of type I
anchor
Drill hole with stop Blow out dust and Insert type I anchor Set with setting tool. Secure part being
drill bit. fragments. into hole. fastened.
42
Anchoring systems
Features
High loading capacity
Force-controlled expansion
Suitable for tension zone
Suitable for shock loading
Fire prevention assessment
Pre-assembled with nut and washer
Cold formed
High reliability
The special expansion-sleeve of the
Hilti HST ensures automatic follow-up
expansion in cracks and, as a result,
HST version : reliable anchoring in the tension zone
Carbon steel grade 5.8, zinc plated to min. of concrete.
5 microns
Intelligent coating
Hilti stainless stud anchors (HSA-R,
HST-R) are coated to prevent binding
between bolt and segment, as well as
between bolt and nut. This ensures
that the anchor can be tightened and
Ordering Hole Anchor Max. fastenable Item no.
designation dia. (mm) length (mm) thickness loosened without problems.
t fix (mm)
HST M 8x75/10 8 75 10 371581 Basic loading data (for a single anchor) : HST
HST M 8x95/30 8 95 30 371582
HST M 8x115/50 8 115 50 371583 Recommended load, L [kN]: concrete f = 25 N/mm2
HST M 10x90/10 10 90 10 371584 rec ck.cube
43
Anchoring systems
Setting details
M 20x170
M 20x200
M 20x270
M 24x200
M 24x230
M 10x110
M 12x115
M 12x145
M 12x185
M 12x215
M 12x235
M 12x255
M 16x140
M 16x165
M 16x215
M 16x255
M 16x295
M 10x90
M 10x30
M 8x75
M 8x95
I [mm] Anchor length 75 95 115 90 110 130 115 145 185 215 235 255 140 165 215 255 295 I [mm] Anchor length 170 200 270 200 230
SW [mm] Width across nut flats 13 17 19 24 hef [mm] Effective embed. depth 101 125
dr [mm] Clearance hole diameter 9 12 14 18 tfix [mm] Max. fastenable thickness 30 60 130 30 60
h1 [mm] Min. depth of drill hole 65 80 95 115 hmin [mm] Min. concrete thickness 200 250
HST-HCR is available up to M16. For HST-R the following lengths are not available: M12x235, M12x255, M20x270
Setting operations
Drill hole with drill bit. Blow out dust and frag- Install anchor. Apply tightening torque.
ments.
44
Anchoring systems
Features
High loading capacity
Force-controlled expansion
Long thread Strong
Head marking for identification after setting
The steel used for the cold-formed HSA is
Firestop assessment very ductile and hardly breaks. This is a
Pre-assembled with nut and washer major benefit, especially if a hole is drilled
Cold formed at an angle.
Version offered
HSA : carbon steel grade 5.8, zinc plated (min. 5 microns)
HSA-F : hot dipped galvanized (ISO 1461, 45 microns) Versatile
HSA-R : A4 stainless steel (DIN 1.4401 / AISI 316)
Versatility in embedment depths. Min.
loading values verified by ETA, even with
reduced anchorage depths.
Hole Anchor Head Max. fastenable thickness Ordering Item no. Item no. Item no.
dia. length marking Standard Reduced designation Zinc plated Hot dipped Stainless
do (mm) I (mm) t fix (mm) t fix (mm) (min. 5 microns) (ISO 1461) (A4/AISI 316)
45
Anchoring systems
Anchor size M6 M8 M10 M12 M16 M20 M6 M8 M10 M12 M16 M20
Standard anchorage depth Reduced anchorage depth
Tensile NRec 2.4 4.8 4.8 8.5 16.6 23.8 1.4 4.3 4.8 5.4 9.5 14.3
Shear VRec 2.6 4.6 7.1 10.1 18.9 29.6 2.4 4.6 7.1 10.1 18.9 29.6
Anchor size M6 M8 M10 M12 M16 M20 M6 M8 M10 M12 M16 M20
Standard anchorage depth Reduced anchorage depth
Tensile NRec 2.4 4.8 4.8 8.5 16.6 23.8 1.4 4.3 4.8 5.4 9.5 14.3
Shear VRec 2.6 4.6 7.1 10.1 18.9 29.6 2.4 4.6 7.1 10.1 18.9 29.6
Anchor size M6 M8 M10 M12 M16 M20 M6 M8 M10 M12 M16 M20
Standard anchorage depth Reduced anchorage depth
Tensile NRec 2.4 4.8 4.1 8.5 15.4 17.5 1.4 3.0 4.1 6.1 9.1 13.2
Shear VRec 2.8 5.2 8.1 11.9 22.4 35.0 2.8 5.2 8.1 11.9 22.4 35.0
Setting details
Setting operations
Drill hole with drill bit. Blow out dust and fragments. Install anchor. Apply tightening torque.
46
Anchoring systems
Fire
Concrete
resistance
Features
For concrete and solid masonry
Force-controlled expansion
No rotation in hole when tightening bolt
Reliable pull-down of part fastened
Material
Steel grade 6.8, galvanised to min. 5 microns
Features
Bridging of gaps
Wide range of applications in
concrete, solid brick etc.
Removable
HLC Sleeve anchor : stud version
Thread dia. Max. thickness Hole dia., Anchor length Hole depth Ordering Item no.
do (mm) fastenable, t fix (mm) do (mm) l (mm) h1 (mm) designation
Setting operations
47
Anchoring systems
Features
Internal thread and small depth of embedment
Anchor flush with surface
Movement-controlled expansion Unsinkable
The flared end on the Hilti HKD-S,
Material ensures accurate setting flush with the
surface independent of the hole depth.
Galvanised min. 8 µm. Available in galvanized steel,
Stainless Steel A4, AISI 316 sherardised and stainless steel. These
anchors
are ideal for setting in the undersides of
cavity ceilings.
HKD-S version : galvanised steel
Thread. Anchor length Hole dia. Hole depth, Ordering
size hnom (mm) do (mm) h1 (mm) designation Item no.
48
Anchoring systems
Setting details
5/16"x30
Anchor size
M 10x30
M 10x40
M 12x50
M 16x65
M 20x80
1/4"x25
3/8"x30
3/8"x40
1/2"x50
5/8"x65
3/4"x80
M 6x25
M 6x30
M 8x30
M 8x40
Setting Details
do [mm] Drill bit diameter 8 8 10 10 12 12 15 20 25
smin/smax [mm] Screwing depth 8/11 8/11 10/13 10/13 12/12 12/16 14/22 18/28 23/34
Tinst [Nm] Tightening torque 4 4 8 8 15 15 35 60 120
dr [mm] Clearance hole 7 7 9 9 12 12 14 18 22
h [mm] Min. base material thickness 100 100 100 100 100 100 100 130 160 HKD-E/-S/-R
TE-CX- TE-C- TE-C-
Drill bit TE-CX-8/17 TE-CX-10/17 TE-CX-12/17 15/17 20/22S 25/27S
TE-TX-12/22 TE-TX- TE-Y- TE-Y-
15/22 20/32S 25/32S
Anchor size M6X30 M8X30 M8X40 M10X30 M10X40 M12X50 M16X65 M20X80
Tensile NRec 3.3 3.3 3.6 3.3 5.1 7.1 12.6 17.2
Shear VRec 2.1 3.9 3.9 4.2 4.6 8.1 12.5 19.9
Note: Edge distance, spacing and other influences are not considered.
Contact Hilti engineering for exact calculation of your specific application.
Setting operations
Drill hole. Blow out dust and Install the anchor. Push in until
frangments. marking is visible.
49
Anchoring systems
HHD-S Cavity anchor
Cavity anchor for installations on gypsum
wallboard or hollow brick
Features
Base material: particle / chip board, drywall panel, hollow blocks
Max. holding power in thin-walled base material owing to
optimised keying hold
Easy, rapid and controlled setting
Prefitted screw in all sizes
Force-controlled expansion
Anchor size
M4/12x38 M4/19x45 M5/12x52 M5/25x65 M6/12x52 M6/24x65 M8/12x54 M8/24x66
Base material
NRec VRec NRec VRec NRec VRec NRec VRec NRec VRec NRec VRec NRec VRec NRec VRec
Particle / chip board 10 [mm] 0.2 0.5 0.2 0.5 0.2 0.5 0.2 0.5
Drywall panel 10 [mm] 0.2 0.5 0.2 0.5 0.2 0.5 0.2 0.5
Drywall panel 12.5 [mm] 0.2 0.5 0.2 0.5 0.2 0.5 0.2 0.5
Drywall panel 2x12.5 [mm] 0.4 1.0 0.3 0.9 0.4 1.0
Gypsum fibreboard 10 [mm] 0.2 0.5 0.3 0.6 0.25 0.8 0.4 0.9
Gypsum fibreboard 12.5 [mm] 0.3 0.6 0.5 1.0 0.3 1.0 0.6 1.2
Gypsum fibreboard 2x12.5 [mm] 0.9 1.1 0.8 1.8 0.9 1.7
Setting details
Anchor size
M 4x12
M 4x19
M 5x12
M 5x25
M 6x12
M 6x24
M 6x40
M 8x24
M 8x40
M8x12
M 4x4
M 4x6
M 5x8
M 6x9
Setting Details
do [mm] Drill bit diameter 8 8 8 8 10 10 10 12 12 12 12 12 12 12
hmin/max [mm] Min./Max.panel thickness 3/4 6/7 10/13 18/20 6/8 11/13 18/28 7/9 11/13 23/25 38/40 11/13 23/25 38/40
tfix [Nm] max.fastenable thickness 15 25 25 25 25 30 30 20 30 30 30 30 30 35
d [mm] Screw diameter M4 M4 M4 M4 M5 M5 M5 M6 M6 M6 M6 M8 M8 M8
Drill bit TE-CX-8/22 TE-CX-10/22 TE-CX-12/22
50
Anchoring systems
HPS-1 : galvanised version Basic loading data (for a single anchor) : HPS-1
different kinds of base material
aerated concrete
Recommended load, Lrec [kN] :
HPS-1 6/15x40 6 42 260350 Note: Edge distance, spacing and other influences are not considered.
Contact Hilti engineering for exact calculation of your specific application.
HPS-1 6/25x50 6 52 260351
HPS-1 6/30x55 6 57 230517
HPS-1 6/40x65 6 67 260352 Setting operations
HPS-1 8/0x25 8 42.5 238160
HPS-1 8/10x40 8 42.5 260353
HPS-1 8/20x50 8 52.5 230518
HPS-1 8/30x60 8 62.5 260354
HPS-1 8/40x70 8 72.5 230519
HPS-1 8/60x90 8 92.5 260355
HPS-1 8/80x110 8 112.5 260356
HPS-1 8/100x130 8 132.5 260367
Setting details
51
Anchoring systems
Ordering Hole dia. Anchor Item no. Ordering Hole dia. Anchor Item no.
designation do (mm) length (mm) designation do (mm) length (mm)
Anchor size
HUD-1 HUD-1 HUD-1 HUD-1 HUD-1 HUD-1
Base material 5x25 6x30 8x40 10x50 12x60 14x70
Wood- Particle Wood- Particle Wood- Particle Wood- Particle
Wood- Wood-
screw board screw board screw board screw board
screw screw
screw screw screw screw
NRec 0.3 0.1 0.55 0.35 0.85 0.5 1.4 - 2.0 3.0
Concrete, fcc = 30N/mm 2
VRec 0.4 - 0.9 - 1.25 - 2.2 - 3.0 5.6
NRec 0.06 0.04 0.1 0.06 0.15 0.1 0.2 - 0.25 0.3
Aerated concrete, PB 2 1)
VRec 0.04 - 0.05 - 0.08 - - - - -
NRec 0.1 0.06 0.15 0.1 0.3 0.2 0.4 - 0.5 0.6
Aerated concrete, PB 4
VRec 0.13 - 0.18 - 0.3 - - - - -
NRec 0.17 0.06 0.35 0.15 0.6 0.35 0.8 - 1.0 1.05)
Solid brick, Mz 20-1.8-1 NF
VRec 0.24 - 0.3 - 0.44 - - - - -
Sand-lime solid block, NRec 0.25 0.15 0.5 0.3 0.85 0.4 1.0 - 1.5 1.55)
KS 12-1.6-2 /DF VRec 0.25 - 0.56 - 0.74 - 1.32 - - -
NRec 0.08 0.05 0.1 0.08 0.2 0.12 0.25 - 0.28 0.32
Hollow brick, HlzB 12-1.0x5DF 1)
VRec 0.23 - 0.35 - - - - - - -
Hollow brick, HlzB 12-1.0x5DF 1)
15 mm plastered DIN 18550
NRec
VRec
0.08 0.05
-
0.15 0.1
-
0.25 0.15 0.03
-
-
-
0.35
-
0.4
Note: Edge distance, spacing and other influences are not
considered. Contact Hilti engineering for exact calculation
0.23 0.35 - - -
NRec 0.04 0.06 0.05 0.08 0.06 0.1 - 0.153) - -
Setting details
tfix [mm] max. fixture thickness depends on screw lengths Recommended woodscrew diameter common woodscrews and particle board screws
Recommended woodscrew type SK/RK SK/RK SK/RK SK/RK SK/RK SK/RK tfix [mm] max. fixture thickness depends on screw length
d [mm] Woodscrew diameter 3.5-4 3.5-4 3.5-4 3.5-4 3.5-4 3.5-4 d [mm] Woodscrew diameter 4.5-5 5-6 7-8
52
Anchoring systems
HLD
Base Material
Anchor working size of anchor Note: Edge distance, spacing and other influences are not
principle HLD 2 HLD 3 HLD 4 considered. Contact Hilti engineering for exact calculation
Concrete: fcc = 15 N/mm 2 C 0.25 0.4 0.5 of your specific application.
Gypsum panel B 0.08 0.08 0.08
Fibre reinforced gypsum
panel 12.5mm A 0.1 - -
Fibre reinforced gypsum
panel 2x12.5mm A - 0.2 -
Anchor size
HLD2 HLD3 HLD4 HLD2 HLD3 HLD4 HLD2 HLD3 HLD4
Setting Details
do1) [mm] Drill bit diameter 9-10 9
h [mm] Wall/panel thickness 4-12 15-19 24-28 12-16 19-23 28-32 from35 from42 from50
53
54
Feel safe and confident in all areas with
Hilti firestop systems
Cable trays
Permanent
CP 601S
CP 680 CP 651
55
Construction chemicals and Firestop systems
FS ONE High performance intumescent Product description
FS-ONE is an acrylic based
Applications intumescent firestop sealant.
Steel, copper and EMT pipes Product features
Insulated steel and copper pipes Contains no halogen or solvents
Jacketed cables and cable bundles High fire rating properties
Small plastic pipes up to 50 mm diameter Water based, easy to clean
For use on concrete, masonry, blockwork, drywall and wood Impermeable to smoke, gas and water
Tested in combination with FS FireBlock as a gap filler
Technical data
Density : approx. 1.5 g/cm3 1 2
Application temperature : +5°C to +40°C
Curing time : approx. 2 mm. in 3 days Ordering Packaging
Expansion rate : 1 : 3-5 designation contents Item no.
Colour : red FS ONE, tube 300 ml 259579
Temperature resistance : -40°C to +100°C FS ONE, foil 600 ml 311387
Accessory
PH-Value : approx. 7.5
Manual dispenser CB 200-P1 310 ml 055205 1
Shore A Hardness : approx. 35 Manual dispenser CS 270-P1CS 600 ml 024669 2
Joint movement capability : max. 10%
Shelf-life : (at 20°C and
stored in a dry place) 9 months
UL 2079, UL1479 FM
(ASTM : E 814)
Permanent fire seal for cables and cable trays max 600x400 mm opening.
Brand
schutz
of a primer
besch
sodfm,e ichtun
v iJdjfiwh g
riuh. N
4i5kirdw oWE
u9+§12 iloi4jtf- x-.vbvb
oeoo vh, ireiv
Permanent fire seal for non-combustible pipes. Smoke, gas and water tight
Permanent fire seal for combustible pipes in conjunction with CP 649.
Excellent movement capability
Permanent fire seal where cables, steel, copper, cast iron or plasticpipes all
pass through the same opening in one seal.
1
Technical data
Chemical basis : Two-component
polyurethanefoam
Colour : Red
2
Fire seal yield : Up to 2.2 I
Cartridge contents : 300 ml
Application temperature : +10°C to +30°C
Temperature resistance : -30°C to +100°C
Minimum temperature :
-Substrate +0°C
-Cartridge +10°C
Storage/transport temperature : +5°C to +25°C Aus-
führungsschild
Curing :
-Non-tacky after Approx. 35 s Ordering Packaging
-Ready to cut after Approx. 1 min designation contents Item no.
Construction materials class as per :
CP 620 Expanding fire seal (300 ml) 12 337725 1
DIN 4102 B1
DSC Dispenser (carton) 1 338720 2
Shelf life : (at 20°C and stored in a dry place) 9 months
Thermal insulation :
-Warm pipes 0.052 W/mk at 90°C
-Cold pipes 0.048 W/mk at 25°C
Comparable to Foamglas, Armaflex and mineral wool
Acoustic insulation (air-borne sound) : 59 db, as per DIN 4109 DIN 4102 BS 476:Part 20, 1987. UL 2079, UL1479 FM
Structure-borne sound insulation : Insulation/integrity (ASTM : E 814)
Pipe/wall 30-50%
56
Construction chemicals and Firestop systems
CP 637 High strength compound System advantages/customer benefits
Quick setting
Applications Load bearing to right foot traffic
Sealing for cables and cable trays opening Adhesive well to common substrates
Sealing for multiple pipe penetration technical data
Technical data
Mix ratio : (recommanded) 3:1 (mortar to water) trowelable
Application temperature : 40°F / 5°C to 110°F / 43°C
Colour : Light red
Expansion on setting (approx) : 0.08%
Compressive strength : 24 hrs.
Pourable : after 24 hrs. 2.5 Nmm2
after drying 5.0 Nmm2
Plastic : after 24 hrs. 4.2 Nmm2
Ordering Packaging
after drying 4.2 Nmm2 designation contents Item no.
Stiff : after 24 hrs. 6.0 Nmm2
after drying 12.3 Nmm2 CP 637 Firestop compound, 13.5 kg bag 1 340645
Curing time : 45 minutes
Formwork removable : 2 hour
BS 476:Part 20, 1987. UL 2079, UL1479
(ASTM : E 814) FM
Insulation/integrity
57
Construction chemicals and Firestop systems
58
Construction chemicals and Firestop systems
CP 651 Firestop cushion Product features
Applications Dust free and tear-resistant
Medium-sized and large penetrations Suitable for temporary and permanent
Temporary or permanent sealing of cable and cable tray penetration installations
Product description Durable and resistant
Ready-to-use firestop cushion made of a homogeneous, graphitebased,
intumescent granulate mixture (which foams and expands in a fire) all
contained in an inner polyethylene bag inside an outer, protective woven
fibre glass bag.
Technical data
Density : approx. 0.33 g/cm3
Weight :
CP 651-L 750 g ± 10%
CP 651-S 300 g ± 10% Ordering Packaging
CP 651-XS 150 g ± 10% designation contents Item no.
Dimensions (LxWxH) : CP 651-L Firestop cushion 5 225585
CP 651-L 340x200x35 mm L/W/H: 340x200x35 mm
CP 651-S 340x100x25 mm CP 651-S Firestop cushion 10 225586
CP 651-XS 340x90x20 mm L/W/H: 340x100x25 mm
Reaction temperature : CP 651-XS Firestop cushion 20 225587
First expansion at + 150°C L/W/H: 340x90x20 mm
Second expansion at + 600°C
Temperature resistance : -40°C to + 120°C
Material class as per DIN 4102, T.1 : B2 BS 476:Part 20, 1987. UL 2079, UL1479
Insulation/integrity (ASTM : E 814)
Technical data
CP 678 CP 679A
Density : approx. 1.3 g/cm3 approx. 1.35 g/cm3 Ordering Packaging
Colour : white white designation contents Item no.
Consistency : Can be applied by paint brush, roller or sprayed CP 678 Firestop cable coating 1 334892
Coverage rate : 1 mm dry =1.8 kg/m2 =1.7 kg/m2 20 kg bucket
Application temperature : +5°C +40°C +5°C +45°C CP 679A Firestop cable coating 1 372097
Dust dry : - 3 hours 20 kg bucket
Touch dry : - 6 hours Internationally tested in accordance with / approved by:
Full cure : 4 hours 24 hours
Temperature resistance : -30°C+ 80°C -20°C+ 80°C American Bureau of Shipping, Certificate
Application of 2 nd layer : after 4 h. after 24 h. of Product Design Assessment.(CP 679A)
Shelf-life after production : 12 months 12 months IEC 332 Part 3 and IEC 331 FM
59
Construction chemicals and Firestop systems
CP 618 Firestop putty stick System advantages/
customer benefits
Applications Base materials Reusable
Single or bundled cables Concrete wall/floor Easy to add or subtract cables
Non-combustible pipes Gypsum wall Fast installation time
Blank openings
Example
Telecommunication and data line penetration of gypsum wall assemblies
Steel conduit and EMT penetration of concrete and block wall assemblies
Blank openings in concrete and block wall assemblies
Technical data
Dimensions : 18 cu. in.
Consistency : Moldable putty Clean plastic Slice CP 618 to be Pack in CP 618 Smooth CP 618 Fasten installation
Colour : Red pipe packed into opening plate (if required)
from stick
Application temperature : 5°C to 35°C
Curing rate : Non-curing Ordering Packaging
designation Item no.
Density : Approx. 1.48 g/cm3 contents
Intumescent activation : Approx. 104°C to 121°C CP 618 Firestop putty stick 12 314721
Surface burning characteristics : Flame spread: 5
(ASTM E 84-96) Smoke Development: 5
UL 2079, UL1479 FM
(ASTM : E 814)
60
Construction chemicals and Firestop systems
Contact us for:
Technical sales representative
Customer service
Hilti service center
Technical advice / engineering support