Professional Documents
Culture Documents
Various Reasons of Cracks in Buildings
Various Reasons of Cracks in Buildings
-الشروخ اإلنشائية
تتعرض الخرسانة المسلحة الجتهادات الشد عند تحميل المنشأ
،ولذلك تحدث شروخ في الكمرات في الجانب المعرض للشد تحت تأثير عزم االنحناء.
هذه الشروخ مقبولة إذا كان سمكها 2.2مم أحيث التآكل والصدأ يتزايدان بسرعة
عندما يزيد سمك الشرخ عن 2.0مم.
-الشروخ نتيجة اجتهادات القص
وتكون شروخاً قطرية ( مائلة)في اتجاه أسياخ التسليح ( التكسيح ) وتحدث
بسبب عيوب في ترابط أسياخ الحديد ذات القطر الكبير مع الخرسانة ،
خاصة إذا كان غطاء التسليح قليل تكون هذه الشروخ ظاهرة بدرجة تشكل خطر ًا مثل:
.1شروخ عزوم االنحناء أو القص التي يزداد اتساعها بصفة مستمرة.
.2شروخ تحدث في أجزاء الخرسانة المعروضة للضغط
وهذا ينبه إلى أن هناك سلوكاً غير عادي يعمل في المنشأ.
.3تفتت الخرسانة في مناطق الضغط
( األعمدة أو الكمرات أو البالطات في الجانب المعرض للضغط )
وهذه الحالة من أقصى درجات الخطورة على المنشأ.
2
3
4
5
6
a) Temperature and drying shrinkage cracks.
With few exceptions, newly placed concrete has the largest volume
that it will ever have. Shrinkage tendency is increased by excessive
drying and/or a significant drop in temperature that can lead to random
cracking if steps are not taken to control the location of the cracks
by providing control joints.
7
When the footing and wall are placed at different times, the shrinkage
rates differ and the footing restrains the shrinkage in the wall causing
cracking. Lack of adequate curing practices can also result in cracking.
b) Settlement cracks.
These occur from non-uniform support of footings or occasionally from
expansive soils.
8
The bottoms of beams are most often affected by the intrusion of salts and by
water that flows through expansion or construction joints. Heavily reinforced with large
diameter reinforcing steel, successful repairs should fully expose the rebar and adjacent
stirrups. After coating the reinforcing steel, forms are constructed to pump in concrete under
pressure and leaking joints are repaired to prevent future deterioration.
9
تشققات تسرب المياه
10
11
Various Reasons of Cracks in Buildings
-Elastic Deformation
When the walls are unevenly loaded, due to variation in stresses
in different parts of wall the cracks are formed in walls. When two
materials having wide different elastic properties are built
12
together under the effect of load, different shear stresses in these
materials create cracks at the junction. Dead and live loads cause
elastic deformation in structural components of a building.
Prevention
Create slip joints under the support of RCC slab on walls. Masonry
work on RCC slabs and beams should not be started before drying
RCC slab and beam. Provide horizontal movement joints between
the top of brick panel and RCC beam/slab.
- Thermal Movement
All materials expand on heat and contract on cool. Thermal
movement in components of structure creates cracks due to tensile
of shear stresses. It is one of the most potent causes of cracking in
buildings and needs attention.
Prevention
Construct joints such as construction joints, expansion joints,
control joints and slip joints. The joints should be planned at the
time of design and be constructed carefully.
- Chemical Reaction
Chemical reactions in building materials increase their volume and
internal stress causes cracks. The components of structure also
weaken due to chemical reactions. Some common instances of
chemical reactions are following.
Sulphate attack on cement products
Carbonation in cement based materials
Corrosion of reinforcement in concrete
Alkali aggregate reaction
Prevention
Use dense and good quality concrete i.e. richer mix of cement
concrete 1:1.5:3 to prevent cracks. Repair corrosive cement
concrete surface by ‘guniting’/ injecting technique after removing
all loose and damaged concrete and cleaning reinforcement from
all rust also.
13
- Shrinkage
Most building materials expend when they absorb moisture from
atmosphere and shrink when they are dry. Cement made materials
shrink due to drying up of the moisture used in their construction.
The factors causing shrinkage in cement concrete and cement
mortar and their preventions are following.
1. Excessive Water
The quantity of water used in the mortar mix can cause
shrinkage. Vibrated concrete has less quantity of water and
lesser shrinkage than manually compacted concrete.
Prevention
Use minimum quantity of water required for mixing cement
concrete or cements mortar according to water cement ratio.
Never allow cement concrete work without mechanical mix and
vibrator.
- Quantity of Cement
As a general rule, the richer the mix is, the greater the
shrinkage/drying will be.
Prevention
Do not use excessive cement in the mortar mix.
- Un-graded Aggregate
Aggregate can cause shrinkage also. If un-graded and fine
material/aggregate is used in cement concrete and cement mortar
which requires more water and can cause greater shrinkage.
Prevention
Use largest possible aggregate and ensure good grading of
materials. The use of water according to required workability has
less shrinkage because of reduction in the porosity of hardened
concrete.
.
14
- Excessive Fine materials
Fine materials take more surface area and require more water for
mix. The use of excessive fine materials i.e. silts; clay and dust in
aggregate create more shrinkage.
Prevention
Do not use fine materials containing silt, clay and dust. Use coarse
sand/fine aggregate in cement concrete and cement mortar mix
which has silt and clay less than 4%. Use coarse aggregate and
fine aggregate after washing to reduce silt contents.
15
A crack of this nature definitely warrants further investigation. While the
crack itself is vertical there is movement along the horizontal plane, which
indicates a shifting of the foundation or ground beneath.
16
BUILDING ON UNSTABLE SOIL,
17
Hair cracks
Structural cracks
18
Cracks in concrete beams due to corrosion or insufficient concrete cover
19
Cracks due to increased bending stress in beams
20
TYPES OF CRACKS IN CONCRETE COLUMNS
TYPES OF CRACKS IN REINFORCED CONCRETE COLUMNS
21
3. Cracks due to increased column load
1. Cracks in reinforced concrete slabs due to Steel Corrosion (cracks parallel to steel bars)
22
3. Cracks in reinforced concrete due to increased load on the slab
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
The figure shows the concrete deformations and cracks. They are presented in a very
large scale to provide a thorough understanding of the way the members behave. In
reality they are so small that they are not visible to the human eye.
The tensile stresses generated in some areas of concrete cause the formation of
cracks; therefore in those areas the necessary reinforcement is placed. When the
cracks are perpendicular to the axis of the member, longitudinal reinforcement is
placed i.e. rebars that prevent the expansion of the hairline cracking.
When the cracks are diagonal, transverse reinforcement i.e. stirrups is placed to
control them.
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
Dr. youssef Hammida
77