|. Main features
1. Weather forecast:
+ Weather forecast indicates the weather trend for next 24 hours.
+ Five weather forecast displays:
° = oo =
-~ ‘wah waa
sunny slightly cloudy cloudy rainy stormy
2. The forecast can be accurate under normal ventilated conditions. Some errors can occur when indoors or in an
air-conditioned environment.
3. Temperature & Humidity:
+ Indoor temperature range: 0 ~ 50°O, resolution: 0.1°C. Ifunder 0°C, it shows LL.L. above 50°C, it shows HHH.
+ Outdoor temperature range: -30°C to 60°C, resolution: 0.1°C. If under -30°C, it shows LL.L. If above 60°C, it shows HH.H.
+ Indoorloutdoor humidity range: 20% to 95%, resolution: 1%. if under 20% it shows LL. fabove 95%, it shows HH.
*"C/'F format temperature display.
4, MAXIMIN temperature and humigity record
5. Freezing- point caution. =
+ If the outdoor temperature falls to between -4°C to 1°C, the “s” Icon will begin flashing. If the temperature falls below
-4°C, the “icon will remain solid on the screen.
6. Auto detecting Barometer: range 800 to 1100HPA.
7, Time(12/24 format), calendar, dual alarms and snooze function.
8: Outdoor sensor low battery detector.
9. The LED back light is activated by sound or touch. It will remainlit for 8 seconds. The LED back light will operate
continuously when connected to the AC adapter.
10. Signal range: 30m.
U. Operating instructions:
Battery Installation and Syncing
For receiver:
+ Open the battery housing of the receiver.
+ Insert three AAA batteries, close the battery housing again.
+ Once the batteries are inserted, the receiver will indicate the first indoor reading in the top left corner.
+ The receiver will then begin searching the outdoor sensor signal
+ Press “UP” on the receiver to select the corresponding channel from the sensor.
For sensor:
+ Open the battery housing of the outdoor sensor.
—+Locate the channel switch in the battery housing and select your desired channel (1,2 0r 3)
Note: there are only two sensors included.
+ Insert two AAA batteries into the battery housing, close the battery housing again.
+ When the batteries have been installed, the sensor will begin transmitting readings to the receiver. The signal indicator
will flash when transmitting successfully.
Note: if the receiver does not display a reading from the outdoor sensor after 3 minutes and only 2 dashes are shown in the
corner of the screen, remove the batteries from both units and repeat the above steps. Alternatively you can begin another
search for the sensor by pressing and holding down the "UP" bution on the back of the receiver for 3 éeconds until the
symbol" @ * flashes.
Setting the time
+ Press and hold "MODE" for 2 seconds to enter the time setting, when the digits are flashing, select the desired time by
pressing the “UP” or "DOWN" button.
+ Setting sequence: time zone—12/24HR—shour—>minute—+year (2000-2099) -smonth—+day-+M/D display format-»SNZ
time (5-60 minutes), after setting, press “MODE” to confirm.
Setting the alarm
+ Under alarm mode, press and hold *MODE" for 2 seconds to enter the alarm setting, when the digits are flashing, select the
desired time by pressing the “UP” or "DOWN’ button.
+ Setting sequence: Hour— minute-rexit, after setting, press "MODE" to confirm.
*Under time modo, press “AL ON/OFF" to turn alarm on/off.
Seiting sequence: +O @ OFF. The alarm will operate for 2 minutes.
+ When the alarm operate, press “SNZ” to enter the snooze status.
+ Under the snooze mode, the alarm *f)" or “®" icon will lash. The alarm will operate at § minute intervals. You can press
any button to stop the alarm,
Useful functions
Press "MODE" for time mode —»alarm made (A1—+A2) switchover.
Press and hold "MODE" for 2 seconds to enter time setting under time mode.
Press and hold "MODE" for 2 seconds to enter alarm setting under alarm mode.
Press "AL ON/OFF” to turn alarm on /off.
Press "UP" for CH1 + CH2 —» CH3 switch,
Press "DOWN' for Celsius/Fahrenheit switch
Press "MEM" to view MAX/MIN temperature and humidity record.
Press and hold *MEM" for more than 2 seconds to reset the values when viewing the memory.
Press and hold “MEM for 2 seconds to switch barometer and date mode under time mode.
Press "SZ" to snooze the alarm for 5 to 60 minutes when alarm is activated under alarm mode.
GUARANTEE Under Australian and New Zealand laws, we guarantee this product is acceptable quality and fit for purpose.