Professional Documents
Culture Documents
V-2172-0009-0086 - 3 Status 1
V-2172-0009-0086 - 3 Status 1
Content
Drawing List Commissioning
Certified drawing 04
Equipment Identification Pre-commissioning recommendations 39
Pumping assembly 06 Commissioning recommendations 39
Part List / Recommend Spare 08
Operation and Service Problem detection
Pump Data Sheet 11
Bolt List 15 No flow| 40
Performance Curves 17 Trapped material 40
Bearing Assembly Insufficient flow 40
Bearing drawing 19 Not enough discharge pressure 40
Lubrication Data Sheet 21 Shaft breakage or damage 40
Motor The motor works with temperature or stops 40
Motor Data Sheet 23 Problem quick guide 41
Motor Drawing 25 Operational
Instrumentation
Design Characteristics Periodical Service 41
Introduction 30 Pump maintenance instructions
Nomenclature 30
General disassembly 42
Inspection and storage Humid part disassembly 42
Bearing column disassembly 43
Inspection 32
Storage Recommendation and Procedures 32 Pump assembly instructions
Indoor long-period storage with Controlled
environment for: General assembly 46
Temperature, humidity, dust and vibration 32 Bearing column assembly 47
Bearing lubrication 49
Indoor / Outdoor with non-controlled Humid part assembly 49
Environment under all types of conditions 32 Spark test for antacid units 51
Safety and Installation General Annexes
Recommendations Pulley assembly 52
Motor storage 53
Safety Precautions 32 General instructions 54
Inspection when receiving the equipment 33 Delivery 54
Pump location 34 Storage 54
Piping 34 It is recommended to storage bearing 54
Sump design and installation instructions 34 With relation to motor storage 55
Suction extension for inferior screen 34 Motor Manual 57
Belt tension 35 Recommend Spare Parts 92
Level controls 36 Lubrication Schedule for all Motors 95
Stick or bar type level control 37
Flotation type level control 37
Bearing lubrication, grease lubrication 38
Weir Minerals │ 5000 Serie Vertical Pump Manual
Certified drawing
Pumping assembly
Listado de Partes
Listado de Partes
GALIGHER 100MR3-5100x1800
BEARING ASSEMBLY D3MRL*5002 GREASE LUBRICATION
ITEM DESCRIPCION CANT CODIGO VULCO
1 BEARING COLUMN 1 V603002100
2 BRG COLUMN BASE 1 V603002200
3 LOWER BEARING CAP 1 V603002300
4 SLINGER 1 V603002400
5 GREASE FITTING 2 1062001000
6 SHAFT 1 V603702529
7 * BEARING CONE 2
8 * BEARING CUP 1 1160204000
9 * CONE SPACER 1
10 * LOCK WASHER 1 1070315000
11 * HEX NUT 1 1130902000
12 * O-RING (LOWER) 1 1031319000
13 * LOWER SEAL 1 1010434000
14 * CHEKSEAL (LOWER) 1 V602002972
15 HEX SCREW 12 1105113000
15A LOCK WASHER 12 1070205000
16 HEX SCREW 6 1106110000
16A * LOCK WASHER 6 1070206000
17 SEAL RING 1 V603002600
18 * UPPER BEARING 1 1160203000
19 UPPER BEARING CAP 1 V603002700
20 * CHEKSEAL (UPPER) 1 V603002972
21 FLINGER 1 V603002829
22 * SEAL RING 1 1010433000
23 * RELIEF FITTING 1 1061905000
24 O-RING 1 1031313000
25 V-RING 1 V603002970
… ….
27 SET SCREW 2 1100637000
28 NIPLE GRASERA 1 1061902000
Rev
DATA SHEET
DOCUMENT NO: 2172-3000-DS-009C
PACKAGE TITLE: SLURRY PUMPS
EQUIPMENT NO(S): 3261-PU-034
EQUIPMENT NAME(S): Copper Regrind Area Sump Pump
EQUIPMENT DESCRIPTION:
VENDOR:
1.00 PROCESS INFORMATION
1.01 Sump pump is used tp clear approx. 80m3 of spillage from the copper 1
PROCESS DESCRIPTION regrind area discharge to the Regrind Mill Feed Hopper (3262-HP-009).
3.05 BASE-FRAME MOUNTING ARRANGEMENT Pump, bearing pedestal and drive to be supported by an integral
horizontal mounting plate.
3.06 MOTOR TERMINAL BOX ARRANGEMENT On RHS, facing motor shaft
3.07 SPEED CONTROL Fixed Speed
3.08 SHAFT SEALING SYSTEM -
3.09 PUMP SUCTION / DISCHARGE FLANGES ASMEB16.5 or Manufacturer's standard. Supply with matching flange
for incorporation in Purchaser's piping if not to ASME B16.5.
3.10 POWER SUPPLY (V / Hz / ph) 460/60/3
9.03 Head figures do not include suction losses of any kind. The suction head quoted is the assumed free liquid surface level above the pump's impeller
Bolt List
Curve
60 1200 1700
1400 rpm
49% 72 1100 1400
NCY
Liner (Norm Max r/min)
CIE
Unlined 1700
EFF I
NI 15366
30 Nominal Correg. TAG: 3261-PU-034 Curve
Flow = 80.0 m³/hr COPPER REGRIND AREA SUMP PUMP Revision 2
Head, H (m)
1200 rpm H(W) = 13.0 m CONSTANCIA PROJECT Revision Notes B
Speed = 877 rpm Consideraciones 45% Reference
Eff = 39.4 %
Madison tests 08-1004, 1210, 1222,
NPSHr = - m G.e Púlpa = 1.53 1224
P = 7 kW G.e Sólidos = 3
Sm = 1.00 Last Issued Jun 96
20 1000 rpm % Sol. Peso = 51.8
D50 = 300 um Issued Jul 09
Hr = 0.829
Er = 0.807
Nominal
800 rpm Flow = 80.0 m³/hr Vel. Periférica = 16 m/s
H(SL) = 10.8 m
10 Speed = 809 rpm BHP = 15.15
Eff = 39.5 % Motor de 20 HP
NPSHr = - m Efectivo a 4200 m.s.n.m
P = 6 kW
Sm = 1.00
Bearing drawing
Motor Drawing
1. Introduction
2. Nomenclature
200 8 Largos
Modelo tipo mm pulg
Tipo Material 600 24
A Antiabrasiva 900 36
R Antiácida 1200 48
N Alto Cromo 1500 60
H Fundición 1800 72
1. Safety precautions
3. Pump Location
4. Piping
5. Mounting Instructions
1.1/2 24 x 22 27.1/2 x 27
3 29-1/2 x 27.1/2 30 x 28
4 34 x 31.1/4 34 x 31.1/4
6. V. Belt Tension
7. Coupling Alignment
8. Controls
2. Screw the float rod (6) into the float ball (2).
1. Pre-Starting Recommendations
2. Star Up Recommendations.
Puma Galigher Vertical, placed in the f The pump must never be submerged above the
horizontal mounting plate as serious damage to both the motor
and bearing assembly could result. If submerged, the
pump bearing assembly should be disassembled,
cleaned, the bearing repacked with fresh grease, and
the motor checked out before further operation.
1. General Disassembly
Impeller, ítem 3
2. Wet-end Disassembly
E. The outer race and rollers of the upper bearing (18) will
now slide out of the bearing column. A hooked wire is
helpful in removing these parts. The seal (20) may also
be removed with the aid of the hooked wire.
G. Drive the shaft (6) and lower bearing out of the bearing
column (1) with a soft-faced mallet.
H. The upper bearing inner racer (18) and seal ring (17)
should be removed from the shaft with a puller.
K. Remove the lower bearing cap (3) and seal (13) from
the shaft.
1. General Assembly
Lifting of the Pump Vertical
Galiggher with chains The component item numbers listed in the assembly
instructions for this section refer to item numbers on
the Assembly Drawings (pages 2 & 4).
INSPECTION
SHAFT
BEARINGS
b) Install lip seal (13) into lower bearing cap (3) with the
seal lip away from the bearing.
d) Slide the bearing cap onto the shaft from the drive end.
Make sure the seal lip is not “turned under” when it is
positioned on the proper area of the shaft. Coat the
O’ring (12) with grease and position the O’ring. Against
the bearing cap flange.
f) Place the seal (14) on the shaft with the lip pointing
away fro the lower bearing.
Position it on the shaft in the recess just above the
locknut. The correct position is with the inner surface of
the seal against the small shoulder nearest the drive
end of the shaft.
g) Install the seal ring (17) onto the shaft. Heat the seal
ring on the bearing heater or in an oven to 275° to 300°
F and quickly slip it onto the shaft. Slide it down the
shaft until it contacts the shoulder. The inner race of
the upper bearing (18) is installed in the same manner.
Slide the inner race down the shaft until it contacts the
seal ring.
Push the shaft assembly into the bearing column until the
outer race of the bottom bearing seats against the
shoulder in the housing.
p) Slide the slinger (4) toward the lower bearing cap (3)
until there is a 1/32” clearance between the two parts. If
the slinger is rubber, this is all that needs to be done. If
the slinger is metal, tighten the two set screws and
recheck the clearance. The shaft should be able to be
rotated by hand, although it may feel “stiff”.
q) BEARING LUBRICATION:
3. Wet-end Assembly
a) Position the cover plate (7) over the end of the shaft
(6) and temporarily secure into place against the
pedestal (1) with nuts and bolts or clamps. Be sure the
f). Bolt the casing (10) into position against the cover plate
(7) and pedestal flange (1). Secure with casing nuts
(11).
IX. ANEXOS
1. Pulley Assembly
GENERAL INSTRUCTIONS
Delivery
Storage
While the engine idle, the weight of the rotor shaft tends
to expel the grease out of the area between the sliding
Rm = Un + 1
Motor Manual