Professional Documents
Culture Documents
You may already have on hand a 12V AC/DC adaptor or 12V from your PC
or 12V battery, but you need a 9V, 2.5A DC power supply for your embedded
system. Certainly, you will need a DC-to-DC converter for the same. You can
use a linear regulator but that requires a large heat-sink. Here is a better
solution to convert 12V DC to 9V DC using a ve-lead TO-220 package IC
LM2576.
Input voltage can be regulated or unregulated. LED1 indicates reverse polarity, and LED2
indicates the presence of input voltage. F1 is a resettable fuse, selectable according to current
capabilities of voltage source and D1 is transient-voltage-suppression (TVS) diode, also known
as transil.
https://www.electronicsforu.com/electronics-projects/convert-12v-dc-to-9v-dc-using-ic-lm2576?utm_source=pushengage&utm_medium=pushnotification&utm_campaign=pushengage 1/5
9/7/2020 12V DC To 9V DC Converter Using LM2576 | Full Electronics Project
Transil is selected according to maximum input voltage. It can be omitted or replaced with a
diode having forward current above 5A. Transil can also be unidirectional or bidirectional
depending on requirement, to protect the circuit from reverse input voltage.
Resistor R1 is used to monitor input current of the circuit. Capacitors C1, C2 and C3 are input
composite capacitors for ltering input noise and ripples. L1 and L2 are inductors wound
over the same common core, and are used to protect input of the IC from input ripples and
noise.
Inductors are selected according to maximum output current. There is a large variety of
inductors available. You can use inductors from old TV sets, monitors or other electronic
equipment. You can also use two separate inductors (L1 and L2), but that will give lower
ltering capabilities. Capacitors C4 and C5 provide the required ltering and reservoir
capabilities for the IC.
LM2576 is adjustable, and its output voltage can be varied from 1.23V to 37V. Here, you need
input voltage slightly higher than 9V. External shut-down capabilities of the IC are not used.
Switching frequency of the regulator is around 52kHz, higher than the audible frequency
range.
D2 must be a Schottky diode (for example, 1N5822, MBR360, MBR340, SR304 or equivalent)
with maximum DC current above 3A. L3 is the only obligatory inductor in the circuit.
Output voltage is programmed with resistors R3 and R4. Output voltage Vout can be
calculated using the following relationship:
Vout=1.23V×(1+R3/R4)
Also, if you know Vout and R4, you can calculate R3 easily using the following relationship:
R3=R4×(Vout/1.23V–1)
https://www.electronicsforu.com/electronics-projects/convert-12v-dc-to-9v-dc-using-ic-lm2576?utm_source=pushengage&utm_medium=pushnotification&utm_campaign=pushengage 2/5
9/7/2020 12V DC To 9V DC Converter Using LM2576 | Full Electronics Project
Internal reference voltage of LM2576 is 1.23V. Voltage produced by L3 is ltered with at least
two capacitors—an electrolytic capacitor (C8) and a high frequency capacitor (C6).
Additionally, output is ltered with LC lter built around L4 and C7. Glowing of LED3 shows
the presence of output voltage. The circuit was designed for output current of 2.5A but
output current can reach 3A and, in that case, output voltage will drop by around 0.3V.
Heat-sink for LM2576 depends on input voltage and load current. Power dissipation on
LM2576 can be signi cant and, hence, requires a small heat-sink with thermal resistance
lower than 30°C/W.
https://www.electronicsforu.com/electronics-projects/convert-12v-dc-to-9v-dc-using-ic-lm2576?utm_source=pushengage&utm_medium=pushnotification&utm_campaign=pushengage 3/5
9/7/2020 12V DC To 9V DC Converter Using LM2576 | Full Electronics Project
Output voltage (9V, 3A) is available across connector CON2. Low-ripples 9V output voltage
can be obtained at CON3. Input voltage from 11V to 15V can be connected at CON1.
Maximum input voltage is limited by maximum voltage of input capacitors and maximum
power dissipation of the IC.
The circuit can be connected to the electrical installation of your car, but make sure that input
is within the working range (11V to 15V). Care should be taken because if the engine is
running and you disconnect the 12V battery of the car, or if the voltage regulator in the car is
not working properly, voltage generated from the generator could be much more than 40V
and pulses may go up to around 100V.
Also, transitions can generate negative input voltages. In real applications, input ltering
capacitors should have working voltages of 150V. It is suggested to have a set of electrolytic
and ceramic capacitors covering large frequency ranges.
https://www.electronicsforu.com/electronics-projects/convert-12v-dc-to-9v-dc-using-ic-lm2576?utm_source=pushengage&utm_medium=pushnotification&utm_campaign=pushengage 4/5
9/7/2020 12V DC To 9V DC Converter Using LM2576 | Full Electronics Project
Petre Tzv. Petrov was a researcher and assistant professor in Technical University of So a,
Bulgaria and expert-lecturer in OFPPT (Casablanca), Kingdom of Morocco. Now, he is working as
an electronics engineer in the private sector in Bulgaria
https://www.electronicsforu.com/electronics-projects/convert-12v-dc-to-9v-dc-using-ic-lm2576?utm_source=pushengage&utm_medium=pushnotification&utm_campaign=pushengage 5/5