Professional Documents
Culture Documents
C2TE
POLYMER MODIFIED LARGE SIZE FOR NATURAL LOW
ADDITIVES TILE STONES CONSUMPTION HIGH GRAB
3-15 mm
IS
O 13 0 07 PERFECT EASY APPLICATION
ADHERENCE LOW VOC TO APPLY THICKNESS
Product description Area of application
Weberset firm is a highly polymer modified, high Refer Tile/Substrate sheet for details
performance thinset adhesive, for tiles, mosaics
and stones, on a variety of surfaces, for both Compliance / Standards
vertical and horizontal application, in indoor as
Specially formulated as per the requirements
well as outdoor use. It is supplied as a drymix
C (Cementatious) 2 (improved) T (Slip resistant)
mortar, to which water needs to be added before
and E (extended open time) of ISO 13007 and EN
application.
12004. Also complies to IS 15477:2004 (Type 2) and
ANSI A118.15
Features & benefits
• Internal and external use. Limitations
• Highly polymer modified: provides high • Do not use on wet screed or plaster. Surface
structural adhesion, which allows to be used on must be fully cured.
a variety of substrates, for fixing a variety of tiles
• Do not use on gypsum plaster or boards, fibre
and stones.
cement boards, or other drywall partitions.
• Can be used for new construction, as well as for
• Can only be used on cementitious waterproofing.
renovation over existing floors/facades.
Don’t not use on epoxy or polyurethane water
• Long open time. proofing.
• Prolonged and easy workability. • Do not use for Installing glass tiles or metal tiles.
Use only Weber bond poxy, for fixing glass and
• Low VOC – for healthy living.
metal tiles.
• No Hacking of substrate required to achieve the
• Do not use on Metal, rubber, plastics, vinyl,
required bonding.
linoleum surface, painted substrates. Contact
• Self-curing properties, which allows for weber representative for fixing these.
no-hassle application, with minimum labor.
• Do not use on surfaces subject to vibrations. Use
• Free flowing product, makes it easier to mix and Weberset flex for vibration prone areas.
apply.
• Do not use for fixing artificial stone or
• No sagformula: allows for hassle free application impregnated stone. Use Weberset ultra for the
on vertical walls, without any slippage. same.
• Water resistant, making it suitable for swimming
pools, bathrooms, kitchen, saunas, and spa. Method of application
• Sustains heat ageing, making it ideal for high Preparing the substrate
Weberset firm
temperature locations for outdoor use, and also • Clean the substrate of oil stains and bond
for hot temperature applications, like Jacuzzi, inhibiting compounds, dirt, dust and laitance, if
sauna etc. any, using high pressure water jet or any other
suitable method.
• No shrinkage, prevents debonding, and gives
• Ensure that the substrate is flat, stable, well
longer life to tiles and stones.
adhered and has a normal absorption.
• Absorbs dynamic load. • Concrete screeds, renders and block work
• Useful for bed thickness of 3-12 mm. May go upto should be cured sufficiently to avoid the
15mm in limited extent.
shrinkage cracks. temperatures, etc.) or a highly absorbent
• Correct the local undulation/damage on the substrate can reduce the open time, even to
substrate at least 48 hours before the just a few minutes. It is therefore necessary that
application of weberset firm. careful checks be made to ensure that a skin
• Saturate the surface well and remove excess does not form on the surface of the spread
water before application of Weberset firm. adhesive. If not, re-freshen the adhesive by
re-spreading with a notched trowel.
• It is not recommended to wet the adhesive with
NOTE :
water once a skin has formed because, instead
- In case of higher undulation, a neat coat of SBR LitX
of dissolving the skin, the water will form an
to be applied on the substrate, followed by
anti-adhesive film.
application of latex modified plaster, to smoothen
• Apply Weberset firm over the surface using the
the surface. (Refer technical datasheet of Weber
straight edge of the notched trowel and then
SBR LitX for further details)
comb the applied adhesive using the notched
- In case of oil stains use of surfactants may be
side of the trowel to achieve the desired
necessary, followed by proper cleaning with water,
thickness.
to avoid debonding of tiles.
• Double buttering is recommended for heavier
- Leave expansion joints of atleast 10mm thickness,
stones.
every 20 feet in the substrate. Do not cover
• If the adhesive is buttered to the tile, then
expansion joints with adhesive, and can be filled
ensure proper coverage of the tile surface to
with appropriate flexible sealant.
evade voids.
• Ensure adequate gap is kept between
Preparing the mix subsequent stones/tiles to accommodate for
• Gradually add 3 parts of Weberset firm to 1 part thermal expansion and contraction.
of clean water (by volume) and mix it to a lump
free, smooth, workable paste using a suitable
NOTE: The size of the notch trowel and the angle
stirrer / low speed drill mix / or any other
of application will determine the bed thickness as
appropriate tool.
per the following formula:
• After mixing allow the mixture to stand for
2 minutes for it to mature. NW × NH × sin θ
Bed Thickness =
(NG+NW)
NOTE : Where:
- Do not attempt to extend the pot life by adding NW is the width of the Notch
more water to the mix. NG is the Gap in between the notches,
- Do not add any additional substance, like cement, NH is the Height of the notch, and
sand etc. to the mix. These may adversely, effect θ is the angle of application
Weberset firm
Stoneseal. Coverage
- To match joint with the color of tile/stone, use Approximately 1.4 – 1.5 Kg/sq. m per mm of
Weberjoint poxy along with Weber joint poxyfill, thickness
available in more than 40 colors.
NOTE : Ensure all surfaces are clean, smooth and
- To get invisible joints between stones, fill with
plum, levelled, free of defects, and without
specially formulated Weber Pearl Armor™
undulations for maximum coverage.
specialty grout.
- To get high aesthetic appeal, fill joints with Weber
Knight Armor™ specialty grout.
Tile/substrate application table
Ceramic tiles
Terracotta
Quarry Tile
Vitrified Tiles
Marble Mosaic
Pavers
Brick
Precast terazzo
Ceramic mosaic
Glass Mosaics
Natural Stone
Porcelain Tiles
SUBSTRATE TYPE SUBSTRATES
Cement-based screeds
and mortars
cement-based
plasters/renders
Cementitious Existing floor
Concrete Masonry
Cement Terrazzo
Blocks
Self Levelling Screeds
Others Brick Masonry
Gypsum plaster
Underfloor Heating
installation
Tiles Ceramic tile ◊ ◊ ◊
Vitrified tile ◊ ◊ ◊
Stone ◊ ◊ ◊
unopened bags, stored in dry condition. product for its intended use. Our products are
manufactured under the Saint-Gobain quality
Condition of sale standards, and subjected to strict quality control
Sold Subject to the company’s condition of sale which procedures. Since the company has no control over
are available on request. site conditions and installation procedures, the
Caution company will not be responsible under any
There may be irritation caused in eyes and skin in circumstances for any loss, damage or liability from
case of contact for a very long time. Please seek incorrect usage.
Technical standards and performance
ISO 13007 and EN 12004
Classification Property Requirement Weberset firm
ANSI A118.15
Condition Property Requirement Weberset firm
7 day dry ≥ 450 psi ( 3.1 N/mm2) 3.22 N/mm2
Glazed Tile Shear Strength 7 day water immersion ≥ 250 psi ( 1.7 N/mm2) 1.85 N/mm2
1 day ≥ 100 psi ( 0.69 N/mm2) 0.73 N/mm2
Impervious Mosaic 7 day dry ≥ 300 psi ( 2.07 N/mm2) 2.58 N/mm2
(Porcelain) Tile Shear Strength 28 day dry ≥ 400 psi ( 2.8 N/mm2) 2.91 N/mm2
7 day water immersion ≥ 200 psi ( 1.38 N/mm2) 1.43 N/mm2
Quarry Tile shear Strength 28 day dry ≥ 150 psi ( 1.03 N/mm2) 1.17 N/mm2
IS 15477 : 2004
Type Property Requirement Weberset firm
5 kN 6.64 kN
Wet Conditions