Professional Documents
Culture Documents
com
Accessory Application Publications No.
AII 49931
INSTALLATION AUTOMATIC DAY/NIGHT 2014 ACCORD
MIRROR 2 AND 4-DOOR Issue Date
INSTRUCTIONS AUG 2013
AUTOMATIC DAY/
NIGHT MIRROR
AUTOMATIC
DAY/NIGHT
8 Wire ties MIRROR
2A FUSE
QB21011AX
© 2013 American Honda Motor Co., Inc. – All Rights Reserved. AII 49931 (1308) 08V03-T2A-1000-90 1 of 13
www.collegehillshonda.com
INSTALLATION Without Moonroof
VEHICLE
Customer Information: The information in this CONNECTORS
installation instruction is intended for use only by skilled
technicians who have the proper tools, equipment, and
training to correctly and safely add equipment to your
vehicle. These procedures should not be attempted by
“do-it-yourselfers.”
LEFT
LENS 4 RETAINING
4 RETAINING TABS QB20902AX
TABS
ROOF
CONSOLE
SUNGLASS
HOLDER RIGHT
(Open.) LENS
4 SCREWS
LEFT
LENS 4 RETAINING
TABS PASSENGER’S
4 RETAINING QB20901BX
SUNVISOR
TABS HOLDER
DRIVER’S (Rotate.)
SUNVISOR
HOLDER
(Rotate.)
QB20903AX
2 of 13 AII 49931 (1308) © 2013 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
4. Remove the rearview mirror cover (two retaining 6. Wrap the end of a flat-tip screwdriver with electrical
tabs). tape. Locate the slot in the bracket cover, and insert
the flat-tip screwdriver into the slot. Push the hook
PLASTIC with the screwdriver.
TRIM TOOL
REARVIEW
MIRROR FLAT-TIP
COVER SCREWDRIVER BRACKET COVER
REARVIEW
MIRROR ELECTRICAL HOOK
(Discard.) 2 RETAINING TABS TAPE
DRIVER’S
SUNVISOR
FRONT
Push the
hook.
© 2013 American Honda Motor Co., Inc. – All Rights Reserved. AII 49931 (1308) 3 of 13
www.collegehillshonda.com
8. Remove the driver’s sunvisor (unplug the vehicle 11. Insert a shop towel in the opening between the
connector, if equipped). driver’s A-pillar trim and the dashboard to prevent
losing the A-pillar clips. Take care not to damage the
driver’s A-pillar trim.
VEHICLE
CONNECTOR
(if equipped) DRIVER’S
DRIVER’S A-PILLAR TRIM
A-PILLAR
FRONT
DRIVER’S
SUNVISOR
QB20904AX
9. Pull away the driver’s door opening seal in the area SHOP TOWEL QB20906AX
shown.
12. Slide the driver’s A-pillar trim up to remove it from the
Pull the clip. upper clip. Carefully remove the shop towel and any
clips that fell from the driver’s A-pillar trim.
NOTE: The upper clip will stay in the body.
UPPER CLIP
DRIVER’S
A-PILLAR
TRIM
DOOR DRIVER’S
OPENING A-PILLAR
SEAL TRIM
(Pull away.) 2 CLIPS
QB20905AX
QB20907AX
4 of 13 AII 49931 (1308) © 2013 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
13. Remove the remaining upper clip from the driver’s 15. If equipped, remove the driver’s dashboard under
A-pillar. cover (turn the knob and release the two clips).
2 CLIPS
2 TABS
(Push.)
UPPER
CLIP
(Discard.)
QB20908AX
DRIVER’S DASHBOARD
UNDER COVER
14. Install the new clip (supplied) to the driver’s A-pillar
KNOB
trim, but do not reinstall the trim at this time. (Turn.)
QB20201AB
CLIP
(supplied)
16. Remove the driver’s dashboard lower cover (nine
clips and unplug the vehicle connectors, if
equipped).
VEHICLE
CONNECTORS 9 CLIPS
DRIVER’S
A-PILLAR TRIM
Q0N0533AH
DRIVER’S DASHBOARD
LOWER COVER QB20202BB
© 2013 American Honda Motor Co., Inc. – All Rights Reserved. AII 49931 (1308) 5 of 13
www.collegehillshonda.com
17. Pull away the door opening seal from around the 4-Door: Two retaining tabs and four clips.
dashboard.
2 RETAINING TABS
4 CLIPS
HOOK
4 CLIPS
DRIVER’S
DASHBOARD
SIDE COVER
DRIVER’S DOOR
SILL TRIM
DOOR OPENING
SEAL 2 BOLTS QB20804AB
QB20909BX
(Pull away.)
18. Remove the driver’s dashboard side cover (two 2-Door: Two retaining tabs and six clips.
bolts, four clips, and one hook).
19. Remove the cover (six retaining tabs). 2 RETAINING TABS
NOTE: Make sure the trunk lid/fuel fill door opener is
unlocked. 6 CLIPS
SELF-TAPPING
SCREW
6 RETAINING
KEY TABS
COVER
Unlock.
DRIVER’S DOOR
SILL TRIM
TRUNK LID/FUEL
FILL DOOR OPENER QB32102AX
DRIVER’S DOOR
SILL TRIM QB20803AB
2 CLIPS
AUTOMATIC DAY/NIGHT
MIRROR HARNESS
2A FUSE LABEL
DRIVER’S
KICK PANEL FUSE CASE
QB20805AB
6216030B
FUSE BOX
MIRROR
MOUNT
AUTOMATIC DAY/
NIGHT MIRROR
Plug in
QB20910AX
here.
FUSE
BOX
FRONT VIEW
AUTOMATIC DAY/NIGHT
MIRROR HARNESS 8-PIN
QB20911AX
OTHER
ACCESSORY
HARNESS
8-PIN
CONNECTOR
VEHICLE QB20913AX
FRAME
FUSE
BOX
28. Secure the automatic day/night mirror harness to the
vehicle harness with one wire tie as shown.
FUSE
BOX
AUTOMATIC DAY/
NIGHT MIRROR
FRONT VIEW
QB20912AX
VEHICLE
CLIP
WIRE TIE QB21001AX
8 of 13 AII 49931 (1308) © 2013 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
29. Route the automatic day/night mirror harness 32. Route the automatic day/night mirror harness
ground terminal toward the vehicle ground terminal. upward. Secure the automatic day/night mirror
harness to the dashboard with one wire tie as
AUTOMATIC DAY/ shown.
NIGHT MIRROR
EDGE OF
URETHANE
HOLE
Align.
SIDE VIEW
WIRE
GROUND TIE
BOLT
VEHICLE
GROUND GROUND
TERMINAL TERMINAL QB21002AX
30. Remove the vehicle ground bolt. Secure the AUTOMATIC DAY/ QB21004AX
automatic day/night mirror harness ground terminal NIGHT MIRROR DASHBOARD
to the vehicle ground terminal, and reinstall the
ground bolt.
31. Secure the automatic day/night mirror harness to the
vehicle harness with two wire ties.
AUTOMATIC DAY/
NIGHT MIRROR
WIRE
TIES
VEHICLE
HARNESS QB21003AX
© 2013 American Honda Motor Co., Inc. – All Rights Reserved. AII 49931 (1308) 9 of 13
www.collegehillshonda.com
33. Route the automatic day/night mirror harness along 2-Door:
the front of the vehicle harness. Align the green tape
on the automatic day/night mirror harness with the AUTOMATIC DAY/
vehicle clip, and secure the automatic day/night NIGHT MIRROR
mirror harness to the vehicle harness with one wire GREEN Align. VEHICLE VEHICLE
tie. TAPE PANEL HARNESS
4-Door:
FRONT
VEHICLE
AUTOMATIC DAY/ CLIP
NIGHT MIRROR
CROSS SECTION
GREEN Align. VEHICLE VEHICLE
TAPE PANEL HARNESS DRIVER’S
A-PILLAR
WIRE
TIE
FRONT
VEHICLE
CLIP
CROSS SECTION
DRIVER’S
A-PILLAR
WIRE
TIE
AUTOMATIC
DAY/NIGHT
MIRROR
HARNESS
QB32103AX
VEHICLE Route to the
HARNESS behind of the
vehicle
connectors.
AUTOMATIC
DAY/NIGHT 34. Route the automatic day/night mirror harness along
MIRROR
HARNESS the driver’s A-pillar, and insert it under the headliner
VEHICLE QB21005BX as shown. Be careful not to crease the headliner.
Route to the
HARNESS front of the
vehicle
connectors.
HEADLINER
AUTOMATIC DAY/NIGHT
MIRROR HARNESS
QB21006AX
10 of 13 AII 49931 (1308) © 2013 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
35. While holding the headliner against the roof, secure 37. Install the automatic day/night mirror harness into
the automatic day/night mirror harness to the vehicle the groove in the harness cover. Secure the harness
harness with one wire tie. Make sure the automatic cover to the mirror stay. Slide the harness cover
day/night mirror harness is not being stretched. behind the headliner.
AUTOMATIC
DAY/NIGHT
MIRROR
HARNESS
Align. FRONT
AUTOMATIC
BOTTOM VIEW DAY/NIGHT Slide.
MIRROR STAY
HARNESS
COVER
AUTOMATIC
Push up. DAY/NIGHT
MIRROR VEHICLE
HARNESS HARNESS
VEHICLE
PANEL
AUTOMATIC DAY/NIGHT QB21009AX
MIRROR
FRONT
WIRE
TIE CROSS SECTION
VEHICLE
HARNESS QB21007BX
AUTOMATIC
DAY/NIGHT
MIRROR HARNESS
7-PIN CONNECTOR
AUTOMATIC
DAY/NIGHT
MIRROR
QB21008AX
© 2013 American Honda Motor Co., Inc. – All Rights Reserved. AII 49931 (1308) 11 of 13
www.collegehillshonda.com
38. Secure the automatic day/night mirror harness to the 2-Door:
vehicle harness with two wire ties as shown.
VEHICLE
4-Door: AUTOMATIC
PANEL
VEHICLE
DAY/NIGHT HARNESS
AUTOMATIC MIRROR
VEHICLE HARNESS
AUTOMATIC PANEL VEHICLE DAY/NIGHT
DAY/NIGHT MIRROR
HARNESS HARNESS
AUTOMATIC MIRROR
HARNESS WIRE TIES FRONT
DAY/NIGHT
MIRROR
HARNESS
WIRE TIES FRONT CROSS SECTION
CROSS SECTION
VEHICLE
WIRE TIE WIRE TIE HARNESS
VEHICLE
WIRE TIE WIRE TIE HARNESS
SIDE VIEW
VEHICLE VEHICLE
SIDE VIEW CLIP CLIP QB32104AX
VEHICLE VEHICLE
CLIP CLIP QB21010BX 39. Check that all wire harnesses are routed properly
and all connectors are plugged in.
40. Reinstall all removed parts.
41. Reconnect the negative cable to the battery.
42. Press and hold the radio power button for two
seconds to restore the radio and navi (if equipped)
system functions.
43. Reset the clock on vehicle without navigation.
44. Do the Function Check.
45. Adjust the zone and calibrate as required.
46. Put the Operating Instructions in the glove box.
12 of 13 AII 49931 (1308) © 2013 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
FUNCTION CHECK
1. Turn the ignition switch to ON (II), but do not start the
engine.
SWITCH
(Turn on.)
LED
AUTOMATIC DAY/NIGHT MIRROR 030406AB
AUTOMATIC DAY/NIGHT
MIRROR
SURFACE
FRONT SENSOR
FLASHLIGHT (Cover.)
REAR
SENSOR
030407AB
© 2013 American Honda Motor Co., Inc. – All Rights Reserved. AII 49931 (1308) 13 of 13