Professional Documents
Culture Documents
com
Produktdatenblatt | Version 1.1
BPW 21
BPW 21
TO39 Ambient Light Sensor
Silicon Photodiode for the Visible Spectral Range
Applications
——Electronic Equipment ——Measurement Levelling
——Industrial Automation (Machine controls, Light
barriers, Vision controls)
Features:
——Package: hermetically sealed
——Especially suitable for applications from 350 nm to 820 nm
——Adapted to human eye sensitivity (Vλ)
——Package similar to TO-5
Ordering Information
Type Photocurrent Photocurrent Ordering Code
typ.
Ev = 1000 lx; Std. Light A; VR = 5 V Ev = 1000 lx; Std. Light A; VR = 5 V
IP IP
Maximum Ratings
TA = 25 °C
Parameter Symbol Values
Characteristics
TA = 25 °C
Parameter Symbol Values
VR = 5 V; RL = 1 kΩ; λ = 550 nm
Fall time tf typ. 1.5 µs
VR = 5 V; RL = 1 kΩ; λ = 550 nm
Forward voltage VF typ. 1.2 V
IF = 100 mA; E = 0
Capacitance C0 typ. 580 pF
VR = 0 V; f = 1 MHz; E = 0
Temperature coefficient of voltage TCV typ. -2.6 mV / K
Temperature coefficient of short-circuit current TCI typ. -0.05 % / K
λ = 550 nm
Noise equivalent power NEP typ. 0.074 pW /
VR = 5 V; λ = 550 nm Hz1/2
Detection limit D* typ. 3.7e12 cm x
VR = 5 V; λ = 550 nm Hz1/2 / W
Srel = f (λ)
Srel = f (φ)
Capacitance 1), 2)
Dark Current 2)
Power Consumption
Ptot = f (TA);
Dimensional Drawing 3)
Chip position
1.75 (0.069)
ø9.5 (0.374)
ø9.0 (0.354)
ø8.3 (0.327)
ø8.0 (0.315)
ø6.0 (0.236)
ø5.8 (0.228)
Radiant
1.55 (0.061) Cathode sensitive area
ø0.45 (0.018)
5.08 (0.200)
0.8
spacing
0.6 5(
5( 0.0
0.0 33
)
26
)
3.4 (0.134) 14.5 (0.571) 9)
3.0 (0.118) 12.5 (0.492) .0 03 1)
( 3
1.0 (0.0
0.3 (0.012) max 0. 8
TTW Soldering
IEC-61760-1 TTW
OHA04645
300
˚C 10 s max., max. contact time 5 s per wave
50
0
0 20 40 60 80 100 120 140 160 180 200 220 s 240
t
Notes
The evaluation of eye safety occurs according to the standard IEC 62471:2006 (photo biological safety of
lamps and lamp systems). Within the risk grouping system of this IEC standard, the LED specified in this
data sheet falls into the class exempt group (exposure time 10000 s). Under real circumstances (for expo-
sure time, conditions of the eye pupils, observation distance), it is assumed that no endangerment to the
eye exists from these devices. As a matter of principle, however, it should be mentioned that intense light
sources have a high secondary exposure potential due to their blinding effect. When looking at bright light
sources (e.g. headlights), temporary reduction in visual acuity and afterimages can occur, leading to irrita-
tion, annoyance, visual impairment, and even accidents, depending on the situation.
Subcomponents of this LED contain, in addition to other substances, metal filled materials including silver.
Metal filled materials can be affected by environments that contain traces of aggressive substances. There-
fore, we recommend that customers minimize LED exposure to aggressive substances during storage, pro-
duction, and use. LEDs that showed visible discoloration when tested using the described tests above did
show no performance deviations within failure limits during the stated test duration. Respective failure limits
are described in the IEC60810.
For further application related informations please visit www.osram-os.com/appnotes
Disclaimer
Disclaimer
Language english will prevail in case of any discrepancies or deviations between the two language word-
ings.
Attention please!
The information describes the type of component and shall not be considered as assured characteristics.
Terms of delivery and rights to change design reserved. Due to technical requirements components may
contain dangerous substances.
For information on the types in question please contact our Sales Organization.
If printed or downloaded, please find the latest version in the OSRAM OS Webside.
Packing
Please use the recycling operators known to you. We can also help you – get in touch with your nearest
sales office.
By agreement we will take packing material back, if it is sorted. You must bear the costs of transport. For
packing material that is returned to us unsorted or which we are not obliged to accept, we shall have to
invoice you for any costs incurred.
Glossary
1)
Testing temperature: TA = 25°C
2)
Typical Values: Due to the special conditions of the manufacturing processes of LED, the typical data
or calculated correlations of technical parameters can only reflect statistical figures. These do not nec-
essarily correspond to the actual parameters of each single product, which could differ from the typical
data and calculated correlations or the typical characteristic line. If requested, e.g. because of technical
improvements, these typ. data will be changed without any further notice.
3)
Tolerance of Measure: Unless otherwise noted in drawing, tolerances are specified with ±0.1 and
dimensions are specified in mm.