Professional Documents
Culture Documents
Throttle Check Valve: RE 27526, Edition: 2015-01, Bosch Rexroth AG
Throttle Check Valve: RE 27526, Edition: 2015-01, Bosch Rexroth AG
RE 27526
Edition: 2015-01
Type Z2FS Replaces: 04.08
▶▶ Size 16
▶▶ Component series 3X
▶▶ Maximum operating pressure 350 bar [5076 psi]
▶▶ Maximum flow 250 l/min [66 US gpm]
tb0221
Features Content
Ordering codes
01 02 03 04 05 06 07 08 09 10 11
Z 2 FS 16 8 – 3X / *
Number of functions
02 2 (throttling in channel A and/or B) 2
04 Size 16 16
Functions in
05 Channel A A
Channel B B
Channel A and B –
Adjustment type
06 Spindle with internal hexagon 8
Seal material
10 NBR seals no code
FKM seals V
Observe compatibility of seals with hydraulic fluid used! (Other seals on request)
1 1
Version “–”
L P X A 2 B Y T L P X A 2 B Y T
1 1
Version “A”
L P X A 2 B Y T L P X A 2 B Y T
1 1
Version “B”
L P X A 2 B Y T L P X A 2 B Y T
Function, section
The Z2FS-type valve is a throttle check valve in sandwich Simultaneously, the hydraulic fluid that is present in chan-
plate design. It is used to limit the flow of one or two nel A① reaches the piston side (5) via the bore (4). In
actuator ports. addition to the spring force, the applied pressure holds
the throttle spool (2.1) in throttle position.
Two throttle check valves aligned symmetrically to each The hydraulic fluid flowing back from actuator B② displaces
other limit the flow in one direction (using an adjustable throttle spool (2.2), thus enabling unhindered flow as a
throttle spool) and allow free return flow in the opposite check valve. Depending on the version (“S” or “S2”), the
direction. throttle effect can occur in the supply or in the discharge.
During supply throttling, the hydraulic fluid arrives at
actuator A② via channel A① via the throttling point (1). Flow limitation
The throttle spool (2.1) can be adjusted axially via the For changing the speed of an actuator, throttle check valve
spindle (3), thus enabling the throttling point to be set (1). is installed between the directional valve and the subplate.
3 5 4 2.1 1 2.2
2
Supply throttling
L T P X Y
A B
① = component side
② = plate side
Technical data
(For applications outside these values, please consult us!)
General
Weight kg [lbs] Approx. 4.7 [10.4]
Installation position Any
Ambient temperature range °C [°F] –30 … +80 [–22 … +176] (NBR seals)
–20 … +80 [-4 … +176] (FKM seals)
Hydraulic
Maximum operating pressure bar [psi] 350 [5076]
Maximum flow l/min 250 [66]
[US gpm]
Hydraulic fluid See table below
Hydraulic fluid temperature range °C [°F] –30 … +80 [–22 … +176] (NBR seals)
–20 … +80 [-4 … +176] (FKM seals)
Viscosity range mm2/s [SUS] 2,8 … 380 [13 … 1760]
Maximum permissible degree of contamination of the Class 20/18/15 1)
Characteristic curves
(measured with HLP46, ϑOil = 40 ± 5 °C [104 ±9 °F])
[100]
6
[80]
[60] 4
[40]
2
[20]
[0]
0 25 50 75 100 125 150 175 200 225 250
[0] [5] [10] [15] [20] [25] [30] [35] [40] [45] [50] [55] [60] [66]
4 5 6 6,5 7 7,5 8
[3626] 250
8,5
Pressure differential in bar [psi] →
[2900] 200
[725] 50 10
12
[145] 10 14
[72.5] 5 16
[0]
0 50 100 150 200 250
[0] [5] [10] [15] [20] [25] [30] [35] [40] [45] [50] [55] [60] [66]
Dimensions
(in mm [inch])
max L6
min L5
max L4
min L3
max L2
min L1
51
L A
3
2 3
2 5 8 4 6
35,5 2 x 9,5 4 x 13
3 3
10,5
F1 F5
7 G1 F2 7
0,01/100
X [0.0004/4.0]
T P
L A B Rzmax 4
Y
Required surface quality of
G2 the valve contact surface
F4 F6 F3
Further information
Bosch Rexroth AG © All rights for this document, are the property of Bosch Rexroth AG, including
Hydraulics registrations of industrial property rights. It may not be reproduced or trans-
Zum Eisengiesser 1 ferred to third parties without our consent.
97816 Lohr am Main, Germany The data specified only serve to describe the product. No conclusions concern-
Phone +49 (0) 93 52 / 18-0 ing a certain condition or suitability for a certain application can be derived
documentation@boschrexroth.de from our information. The information provided does not release the user from
www.boschrexroth.de the obligation to exercise their own judgment and verification.
It must be remembered that our products are subject to a natural process of
wear and aging.