Professional Documents
Culture Documents
w w w . D a t a S h e e t . c o . k r
D a t a s h e e t p
Document Version : 0.3
Date : 2007/08/01
Product Specifications
www.DataSheet.co.kr
( ) Preliminary Specifications
(*) Final Specifications
No
COVER
CONTENTS
RECORD OF REVISIONS
1 GENERAL DESCRIPTION
3 ELECTRICAL SPECIFICATIONS
4 OPTICAL SPECIFICATIONS
5 MECHANICAL CHARACTERISTICS
6 RELIABLITY
7 INTERNATIONAL STANDARDS
7-1 SAFETY
7-2 EMC
8 PACKING
9 PRECAUTIONS
78W (Min), 85W (Typ), 96W (Max.) 79.2W (Min), 88W (Typ), 96.8W (Max.)
3-2 LVDS option mode LVDS option mode definition update Update
Electrical Specification: External PWM setting Remove External PWM setting Update
4-Note Contrast ratio: Surface Luminance: Lon1/Loff1 Contrast ratio: Surface Luminance: Lon5/Loff5 Update
0.2 2007/06/22 3-1 Electrical Characteristics: LVDS Interface Electrical Characteristics: LVDS Interface Update
VTH: +100mV (Max) VTL: -100mV (Min) VTH: 100mV (Min) VTL: 100mV (Min)
3-4 Signal timing waveform: 1Ch Update signal timing waveform to 2Ch Update
3 Electrical Specification: Input Current (Turn on) Electrical Specification: Input Current (Turn on) Update
4.3 (Min), 4.5 (Typ), 4.7 (Max.) 4.3 (Typ), 4.7 (Max)
Electrical Specification: Input Power (Turn on) Electrical Specification: Power Consumption Update
Electrical Specification: Input Current (Stable) Electrical Specification: Input Current (Stable)
6 Reliability test conditions Reliability: Modify the HTO and add THB condition Update
8 Packing: Carton Packing: Add carton drawing and shipment data Update
Package and carton drawing Update Package and carton drawing with real picture Update
* General Information
Items Specification Unit Note
Active Screen Size 31.51 inches w w w . D a t
D
2. Absolute Maximum Ratings
The following are maximum values which, if exceeded, may cause permanent damage to the
unit.
greater than 40℃, the wet bulb temperature must not exceed 39℃.
LCD:
Power Supply Input Voltage Vcc 10.8 12.0 13.2 Vdc 1
Power Supply Input Current Icc - 1 1.2 A 2
Power Consumption Pc - 12 13.2 Watt 2
Inrush Current IRUSH - 4 6 Apeak 3
LVDS Differential Input High VTH 100 mV 4
Interface Threshold Voltage
mV 4
Threshold Voltage
Note :
1. The ripple voltage should be controlled under 10% of VCC
2. Vcc=5.0V, f v = 60Hz, fCLK=81.5Mhz , 25℃, Test Pattern : White Pattern
3. Measurement condition :
10%
GND
Trush = 470 uS
4. VCIM = 1.2V
VTH
VCIM
VIL
0V
5. The performance of the Lamp in LCM, for example life time or brightness, is extremely influenced by
the characteristics of the DC-AC Inverter. So all the parameters of an inverter should be carefully
designed so as not to produce too much leakage current from high-voltage output of the inverter. When
you design or order the inverter, please make sure unwanted lighting caused by the mismatch of the
lamp and the inverter (no lighting, flicker, etc) never occurs. When you confirm it, the LCD Assembly
www.DataSheet.co.kr
www.DataSheet.co.kr
Note:
1. All GND (ground) pins should be connected together and should also be connected to the
LCD’s metal frame. All Vcc (power input) pins should be connected together.
2. High: NS mode
Low/Open: JEIDA mode
3. Do not connect NC pins. Connecting these pins to Ground or any voltage is not allowable.
ORXCLK+
ORXCLK-
ORX0 OR0 OG0 OR5 OR4 OR3 OR2 OR1 OR0 OG0
ORX1 OG1 OB1 OB0 OG5 OG4 OG3 OG2 OG1 OB1
ERXCLK+
ERXCLK-
ERX0 ER0 EG0 ER5 ER4 ER3 ER2 ER1 ER0 EG0
ERX1 EG1 EB1 EB0 EG5 EG4 EG3 EG2 EG1 EB1
Note:
u Odd data is the first priority. www.DataSheet.co.kr
ORXCLK+
ORXCLK-
ORX0 OR2 OG2 OR7 OR6 OR5 OR4 OR3 OR2 OG2
ORX1 OG3 OB3 OB2 OG7 OG6 OG5 OG4 OG3 OB3
ERXCLK+
ERXCLK-
ERX0 ER2 EG2 ER7 ER6 ER5 ER4 ER3 ER2 EG2
ERX1 EG3 EB3 EB2 EG7 EG6 EG5 EG4 EG3 EB2
2. Input specification
CN1: JST PHR-14 or equivalent
No Symbol Description
6 GND Ground
7 GND Ground
8 GND Ground
9 GND Ground
10 GND Ground
12 VBLON (Enable Pin) On/Off control Signal; High: On; Low: Off
13 VDIM (LCD Bright) Internal PWM Dimming control signal input (DC 0~3.3V)
D a t a s h e e t p d f - h t t p : / / w w w . D a t a S h e e t 4 U
3-3 Signal Timing Specifications
This is the signal timing required at the input of the User connector. All of the interface signal timing
should be satisfied with the following specifications for it ’s proper operation.
DE mode only
www.DataSheet.co.kr
The brightness of each primary color (red, green and blue) is based on the 8 bit gray scale data input for the
color; the higher the binary input, the brighter the color. The table below provides a reference for color versus
data input.
COLOR DATA REFERENCE
RED(001) 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
RED ----
RED(254) 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
RED(255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
GREEN(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
GREEN(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0
GREEN ----
GREEN(254) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0
GREEN(255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
BLUE(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
BLUE(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
BLUE -------
BLUE(254) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0
BLUE(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Note:
The timing controller will not be damaged in case of TV set AC input power suddenly shut down.
Once power reset, it should follow power sequence as spec. definition.
(1) Apply the lamp voltage within the LCD operation range. When the back-light turns on before the LCD
operation or the LCD turns off before the back-light turns off, the display may momentarily become
abnormal screen.
www.DataSheet.co.kr
Color Coordinates
RED RX 0.64
RY 0.33
GREEN GX 0.29
GY 0.60
Typ.-0.03 Typ.+0.03
BLUE BX 0.15
BY 0.06
WHITE WX 0.28
WY 0.29
Viewing Angle
x axis, right(φ=0°) θr 89 Degree 6
x axis, left(φ=180°) θl 89
y axis, up(φ=90°) θu 89
y axis, down (φ=0°) θd 89
2. Surface luminance is luminance value at point 1 across the LCD surface 50cm from the surface with all
pixels displaying white. From more information see FIG 2. When VDDB = 24V, IDDB = 3.5A. LWH=Lon1
Where Lon1 is the luminance with all pixels displaying white at center 1 location.
3. The variation in surface luminance, δWHITE is defined (center of Screen) as:
δWHITE(9P)= Maximum(Lon1, Lon2,…,Lon9)/ Minimum(Lon1, Lon2,…Lon9)
4. Response time is the time required for the display to transition from black to white (Ton) and from white to
black (Toff). For additional information see FIG3.
5. Response time Tγ is the average time required for display transition by switching the input signal for five
luminance ratio (0%,25%,50%,75%,100% brightness matrix) and is based on fv=120Hz to optimize.
www.DataSheet.co.kr
6. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are determined for the
horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD surface.
For more information see FIG4.
FIG. 2 Luminance
H/2 L1 L2 L3
L4 L5 L6 H
L7 L8 L9
H/6
V/6 V/2
L0,15,L31,….L255 L0,15,L31,….L255
Photodetector
Output
L0,15,L31,….L255
Time
TrR
Datasheetpdf-htp:/www.DataSheet4U.net/
5. Mechanical Characteristics
The contents provide general mechanical characteristics for the model T315XW02 VF. In addition the figures in
the next page are detailed mechanical drawing of the LCD.
Horizontal 760.0mm
Outline Dimension Vertical 450.0mm
Depth 45mm
Bezel Opening Horizontal 703.6mm
Vertical 398.3mm
Active Display Area Horizontal 697.68mm
Vertical 392.26mm
Weight 6500g Typ.
Surface Treatment AG, 3H
www.DataSheet.co.kr
Datasheetpdf-htp:/www.DataSheet4U.net/
Front:
www.DataSheet.co.kr
- T315XW02 VF
No Reproduction and Redistribution Allowed
HIGH VOLTAGE
CAUTION
R IS K OF E LE C TRIC SHOC K.
D IS CO NN EC T TH E ELE CTR IC
POWE R BE FO RE S ER VIC IN G.
COLD CATHODE FLUORESCENT LAMP IN LCD PANEL CONTAINS A SMALL AMOUNT OF
MERCURY PLEASE FOLLOW LOCAL ORDINANCES OR REGULAT IONS F OR DISPOSAL.
7-2. EMC
a) ANSI C63.4 “Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and
Electrical Equipment in the Range of 9kHz to 40GHz. “American National standards Institute(ANSI),
1992
b) C.I.S.P.R “Limits and Methods of Measurement of Radio Interface Characteristics of Information
Technology Equipment.” International Special committee on Radio Interference.
www.DataSheet.co.kr
TW7600300053
TW76003: Production Lot, T: Taiwan, M: China
00053: Panel Serial Number
ZMA: AUO internal code
Manufactured 07/25: 2007 week 25
Made In Taiwan: Taiwan made
Made In China: China made
w w w . D a t a S h e e t . c o . k r
Carton Label :
D a t a s h e e t p
Carton:
W
H
L
Inside Dim
www.DataSheet.co.kr
516
270
868
ExtensionDim
W 275±3
H 525±3
L 873±3
W
H
Outside Dim
L
535±5
280±5
878±5
139±2
Specification
Item Packing Remark
Qty. Dimension
1 Packing BOX 4pcs/box 878(L)mm*280(W)mm*535(H)mm
2 Pallet 1 1140(L)mm*890(W)mm*138(H)mm
3 Boxes per Pallet 8 boxes/Pallet
4 Panels per Pallet 32pcs/pallet
Stretch film
www.DataSheet.co.kr
Corner angle
Pallet
D a t a s h e e t p d
9-3 ELECTROSTATIC DISCHARGE CONTROL
Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain that
treatment persons are connected to ground through wrist band etc. And don’t touch interface pin directly.
(3) You can remove the glue easily. When the glue remains on the Bezel or its vestige is recognized, please
wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal-hexane.
D a t a s h e e t p d