PORTABLE TWO-WAY RADIO.GENERAL DESCRIPTION
The transceiver is a micro-miniature multiband
FM transceiver with extensive receive frequency
coverage, providing local-area two-way
‘amateur communications along with unmatched
‘monitoring capability.
We appreciate your purchase of our transceiver,
and encourage you to read this manual
thoroughly, and learn about many exciting
features.[loosens Ea:
PRECAUTIONS
‘#Refer service to qualified technicians only:
‘Do not disassemble or madify the transceiver for any reason,
‘#Do not expose the transceiver under direct sunlight long or to
‘extremely hot condition
‘#00 not place the transceiver on the unstable surface.
‘#Keep the transceiver out of dust, moisture, water.
‘#Do not operate the transceiver or charge the battery pack under
‘explosive conditions.
SAFETY
Itis important that the operator is aware of and understands
hazards common to the operation of any transceiver,
Awwarning
Please turn off the transceiver off atthe following locations:
>In explosive stmospheres(infammable gas, dust particles, metalic
powders, grain powders, etc).
Dle taking on fuel or while parking t gasoline service stations.
D> Near explosives or blasting sites
CONTENTS
UNPACKING AND CHECKING EQUIPMENTS ot
INSTALLATION OF ACCESSORIES 02
BATTERY CHARGING
GETTING ACQUAINTED 08
OPERATION 16
ADVANCED OPERATION
ADDITIONAL FUNCTIONS AND SETTINGS ~
‘TROUBLESHOOTING GUIDE 3
‘SPECIFICATIONS,
L>UNPACKING AND CHECKING EQUIPMENTS
Carefully unpack the transceiver. We recommend that you identify
the tems listed inthe following table before discarding the packing
material. If any items are missing or have been damaged during
shipment, please contact the dealers immediately,
Standard Accessories
TEM [aunty
‘URF(shony 1
Antenna [VHF (long)
‘AC Adapter
Trion Battery
Bolt Cip
Hand Strap
‘SPBMIC.
Tistuction Manual
7 g
uiondatny Banca tp
Optional Accessories
e
‘Cigarette Lighter Adapter
INSTALLATION OF ACCESSORIES
ANTENNA INSTALLATION
pled antenna provides goed results over
tho enie roquoncy range ofthe ranecover
However, for enhanced based station medium:
wave and shortwave reception, you may wish fo
Connect an extzmal antanna, as the supplied
Anton is vary small and ean fot be expocted To
provide high performance at these requencies.Note:
Never transmit without having an antenna
Connected
‘Wen instaling the supplied antenna, never old
the upper part of antenna while sewing tnt
the mating connector onthe transceiver.
using an extarnal antenna for transmission,
ensure thatthe SINR presented fo the ranscever
is'1St orlower, 0 avete excossive fod tne oss.
BELT CLIP INSTALLATION
I necessary, instal the Bel lp ito the location
‘on the back ofthe battery. (Sve PIC 2},
Note:
Do Not use the glue to fasten the serow, whe
instaling the bet lip. Otherwise, the acryic ac
ofthe give may damage the battery panel
‘SP.&MIC. INSTALLATION
Insert the speaker/microphone plugs into the
'SPAMIC, Jacks of the transceiver, (See PIC 3)
>
BATTERY PACK INSTALLATION
‘The ballary pack is a high-performance Li-ion battery providing high
‘capaciy ina very compact package. Under normal use, the battery may
be used for approximately 400 charge cycles, after which operating ime
may be expected to decrease. you have an older balory thats displaying
‘diminished capacity, you should replace the battery with a new one,
Installation of the battery is easy and quick:
1.Slide the Battery Cover othe Unlock pasion and then slide tho Battery
Cover toward the batiom fo remove i
install the batlory into the Balory Compartment
'3,Replace the Battery Cover and then sie the Battery Cover Latch into
{the Lock position
=
S>
BATTERY CHARGING
Ife battery has never been used, or is charge is depleted, it may be
‘charged by connecting the Batlary Charger, as shown inthe lustation,
tthe EXT DC Jack. IFonly 12-18 Voll OC power
Li
phis available, tho optional DC Adaptor (with its
‘igarette lighter plug) may also be used for
‘charging the battery
‘While the battery is being charged, the display
wil indcate (See PIC 5). this S-meter wil dole
‘according tothe charging status, and the TXIBUSY
indicator wil glow cod
‘When the charging ' Frished, tho TX indleator
wil glow green
“The charger is only designed for the charging of
‘our battery and is ot suitable for othor purposes.
Please be advigod thatthe chargor may contibto
noise to TV and radio recoption inthe immadiat
vient, s0 we donot recommend ts use adjacent
{such devices,
Important Note:
41) Perform the battery charging where the ambient temperature range is
-41°F-95'F (+8°0-+35C) Charge out ofthis range could cause damage
tothe battery pack.
2) Ifthe charge is not completed in several hours, the battery may be
eterirated. Do not attempt to forcibly charge the batter, please
contact the dealer
3) you do not use the transceiver for along time, remove the battery
ack from the transceiver, as battery leakage could cause damage to
the transceiver and te battery pack.
4) While in storage, the charge wl drain sighy over ime and the batory
‘shouldbe recharged 80% each six months.
, oN
GETTING ACQUAINTED
ANTENNA Jack —
eee
Leo St
PTT Switch
FIALERT Switch
LAMPIFM Switch
ONIOFF Key
Speaker
UN MODE Key’THE DEFINITION OF THE CONTROL
he main uring Dial used fr sating tho on
Faavaney, and ie used for aust volo lo
LD DISPLAY
The cisplay icons appear when certain operations are performed or certain
ona | falls Sao iteaes eras specie features are activated. It wll help you to know the meaning of
nek ppt tole te iocarca dal oe, the indcator and know how tase functions
[Tap rismtcn Press tis stn fo ronan ae elaae WI
mT fro teacersouve : 199 comanenen
[VOLMONKay [Pees sonny eos vov ned conan he See ges
[Trower [Fier ag ia ty ere soos eof Re]
ALERT] | Spey Sean Mapoal er bee gi eee TON [DESCRIPTION
Pabod | Secondary Keypataave (Press ALERT) |
BL Res ses earn [TBE operaing Gana Number tera Cranne! Nae
IMENUILOCK) | Sabine Key Lose le, ‘aa |CTCSS Operation
esenmr oe rac ‘a [508 Operation
| stress ith ig VFO UF Mae ar VTE Oo
juvimove] _ | Free and iateswien neque) cont bomen VFO a
(VIMOPE] _[Sraienoy Syseme: Fi (7-106)
Tawra [RSURREEI iit Toeh Poss ao acs To rows Poe
Fepcnaoon |RSS See AR for ERICA Weta Sandia
: keypad tock Acie
Fstuvimove] | Beaman is os rman zi
Fain | BREALERT tenia Aenea
[WOUMON [oA | Pes VOLO: en tee OAL Eb. aa —hri=— $<
7 08
g »[SO ones SO aoe 8
COMBINATION KEY FUNCTION MENU DESCRIPTION
‘Tone Cating A
Press and holdin the buton [PTT] and [ VOLIMON!] to enter the Tone pero pete ae
‘Caliog Mase(1780H2). The transceiver send outhe signal (1750H2).Release sii | rec00 OFRETTOS DCS
‘he buton { VOUMON! to ext 2 | Txcooe OFFCTCSS, DCS
3 _| sat em os
Restore to Default Factory Setting 4 MoH co ria ‘OFFION Koy
Press and hol the key LONOFF ] + [FIALERT) , a cee oe
then Power ON, be Wansceiver wil restore to the
etal actor song oe =
Factory Default Selting as:400.000MHz, No 7 | Rowen or oxsaron HOHLOW
{CTCSSIBCS, Low Outout power, Batlary Save, 3 [ oiroanaorran ONOFF
Volume Level’, $25, Key Te ON, other stings 2 ser 2825
OFF 7o_| oFFser @-379060--60.0060
| sHer a
12_| STE (aromtimeo ‘ONOFF
Ee
16 _| SAVE ey Soe ‘ONOFF
15 _| ToT tment ‘OFF 0/0/9071 2071601605.
16 | SCAN emo ToGo
17__| RELAY repmon sont Ronon | ONOFF
18 [Sto wmownionan | ONO
, “ N a’MENU SETTING
Press [MENU/LOCK], come to MENU
[o1]RXCODE
Pross [ MENU/LOCK ] , turn clockwise or
‘counterclockwise [ DIAL} , come to MENU [02]
‘TXCODE.
Press [ MENUILOCK J , turn clockwise or
‘counterclockwise
[DIAL], come to MENU [03] SaL.
Press { MENUILOCK ] , turn clockwise or
‘counterclockwise
{DIAL} , come to MENU [04] LIGHT.
Li >
Press [ MENU/LOCK ] , turn clockwise or
counterclockwise
TLDIAL J , come to MENU [05] K TONE,
Pross [ MENUILOCK], turn clockwise or
counterclockwise
DIAL], come to MENU [06] VOX
Pross [MENU/LOCK], turn clockwise or
counterclockwise
DIAL}, come to MENU [07] POWER.
Press [MENUILOCK]}., turn clockwise or
counterclockwise
DIAL}, come to MENU (08} Dw.
Li»Press [MENUILOCK]., turn clockwise or
counterclockwise
TOIAL ], come to MENU (03} STEP.
Press [MENUILOCK]., turn clockwise or
counterclockwise
TOIAL], come to MENU [0] OFFSET.
Press [MENUILOCK] turn clockwise or
counterclockwise
DIAL] , come to MENU [11] SHIFT.
Pross [MENUILOCK] turn clockwise or
counterclockwise
[DIAL], come to MENU 12} STE,
Lh»
Press [MENUILOCK], turn clockwise or
counterclockwise
TOIAL] , come to MENU [13] WIN.
Press [MENUILOCK]., turn clockwise or
counterclockwise
DIAL , come to MENU(‘4) SAVE.
Press [MENUILOCK]. turn clockwise or
counterclockwise
(DIAL , come to MENU [15] TOT.
Press [MENUILOCK]. turn clockwise or
counterclockwise
DIAL], come to MENU(16] SCANM.
LhPress [MENUILOCK] turn clockwise or
counterclockwise
DIAL], come to MENU [17] RELAY
Press [MENUILOCK], turn clockwise or (ay
counterclockwise CLO
DIAL] , come to MENU [18] BCLO,
‘@ Press thekey [ UVIMODE }confim the setting, and EXIT the functions
setng
‘@Battory Save, Time-out Limi, WatvNarrow, only be changed via program
software
‘#Under the VFO mode, urn clockwise or counterclockwise { DIAL} to
Increase or decrease the frequency.
Lh»
OPERATION
POWER ON/OFF
41.8e sure the Battery Pack s installed, and the
battery is fully charged. Connect the antenna
to the top panel ANTENNA jack,
2.Press and hold the key [ON/OFF ] the curent
DC supply voltage wil appear on the LCD for
2 seconds, and beeps willbe heard, the display
‘il sume its normalinglcation af he operating
frequency,
3.To tum the transceiver off, press and hold the
key LONIOFF ] again for one secone.
ADJUSTING THE VOLUME LEVEL
Pallthe [DIAL] knob to unlock the mecharical dal lock, then ola the
{DIAL} knob attr press the key { VOLMON } , to set the desiod audio
level. Clockwise rotation increased the volume level
LhADVANCED OPERATION
RXCODE
‘You may sometimes want to hear calls ror only
“specie persons or groups: In his case, use the
‘selective cal allows you to ignore unwanted calls
{rom other persons who are using the same
frequency.
‘Sot the receiving signal according tothe below
Instructions:
1)Press [ MENULOCK ], rotate the [DIAL]
knob, come to MENU [1]; RXCODE
2yThen press [ UV] key, enter the set mode.
3)Clockutise or counterclockwise rotation of
DIAL] kro® to select from OFF /67.0-754N,
press [ MENUILOCK ] again to select the code
(Postive or negative), such as 023N--023.
—+ OF F—+67.0—+023N—0231
Note:
[cTCSs:67H2-~258.1H2(50 groups):
10¢:023N-754N(104 groups}
4)Press [UNV key to save the setting and
EXIT. Pross.[ MENUILOCK]] or [PTT] EXIT
ne —
‘TXCODE
Set the transmiting signal according to the below
Inseuctons:
‘)Press [ MENUILOCK } , rotate the. [DIAL]
kab, come to MENU [2], TXCODE
2yThen press [ UV] key, enter the set mode.
3)Clockwise or counterclockwise rotation of
DIAL] knob to select rom OFF /67.0-754N,
press. [MENUILOCK] again, to select the
‘ode (Positive or negative), such as 023N-—
0231
OFF —+67.0—+023N 0201
Note:
[cTeSs:67Hz~-254.1H2(50 groups)0CS:
(028N-754N(104 groups}]
-4)Press [UNV] key to save the setting and EXIT.
Press [ MENUILOCK ] or { PTT] , EXIT to
rormal operation,
LiSQL (SQUELCH ADJUSTMENT)
‘Squoich System allows ou io mute the background
noise when no signal being received. The Squeleh
system make ‘Standby’ operation more pleasant,
and significantly reduces battery current
consumption. Please adjust the Squelch level
according othe following instructions:
4)Press [ MENUILOCK } , rotate the. {DIAL }
knob, come to MENU [3]: SOL
2)Then press [UNV] key, come to the default
‘selting level SOL
3)Clockwise or counterclockwise rotation of
[DIAL] knob to adjust between
y1/21i4/S16/78/9 (Default Squeleh level as
5). Select the lovel at which the background
noise is just oliminated when tore is no signal
Press. [UV] key o save the setting
4)Press [ MENUILOGK]} or [PTT], EXIT t0
‘normal operation
LIGHT(LCD ILLUMINATION ON/KEYIOFF)
LUV.AR incodes a reddish ilumination lam which
aids in nightime operation. The red iluminaton
yields clear viewing of the display in a dark
environment, wth minimal degradation of your
night vision. Three options for activating the lamp
Li
Key: tuminstes the LCD when any key pressed.
ON: tllminates the LCD continuously,
OFF: Disables the LCO lame,
Here isthe procedure for setting up the Lamp
mode:
‘)Press [ MENUMOCK } , rotate the [ DIAL}
knob, come to MENU [4 LIGHT.
2)Then press [ UV] key to enter the set mode.
3)Clockwise or counterclockwise rotation of bn
[DIAL] knob to set ON/OFFIKEY
‘Press. [ UNV} key to ave tho soting.
s5)Press [ MENUILOCK } or { PTT], EXIT to
normal operation,
KTONE (KEYPAD BEEPER ON/OFF)
It the Keypad Beeper will inconvenience you
(especialy bong operated nthe stent room), you
may dsable the Beopor according to the folowing
instructions:
‘)Press [ MENUMLOCK ] , rotate the [DIAL]
knob, come to MENU [5] KTONE
2)Thon press [ UV} key to enter the set mode.
, ON3)Clockuise or counterclockwise rotation of
[DIAL J knob to set ONDOFF
‘4)Press_[ UNV ] key to save te seting.
5)Press [ MENUILOCK ] orPTT], EXIT to
ormal operation,
{ON-The beeper being activates, LOD displays
Icon, OFF-The beoper boing disabled)
VOX(VOICE OPERATED TRANSMISSION)
\Vox.elminats the necssty of manual switching
(othe transmission Mode each tie you want 10
transmit The tansceWver automaticaly switches
to transmission mode when the VOX crutry
Senses that you have begun speaking ino tho
ilcophane, Please sel according othe flowing
instructions:
‘Press [ MENUILOCK ] rotate tne [ OIAL]
rab, come to MENU [5 VOX
2yTHen press UNV} key to enter the sat mode.
2)Clockwise or counterclockwise rotation of
[DIAL] knob o set OFF 24/0769
4)Press_[ UNV ] key to save the setting.
Li
s5)Press [ MENUILOCK } or [ PTT] , EXIT t0
‘ormal operation,
NOTE:
Grade 7-9: the Most Sensitive VOX Gain Level=
Set under silent conciions
Grade 4-6: the Medium Sensitive VOX Gain
LLeverSet under commen conetions
Giade'-: the Least Senstive VOX Gain Lovel-
St unr too much noise condtions.
‘When VOX funetion is activated, the LCD will
display the ICON 'VOX.
POWER (HIGH/LOW RF OUTPUT
POWER SELECTION)
Select the HighfLow RF Output Power, please set
‘according to the folowing instructions
‘yPress { MENUILOCK J , rotate the [IAL]
knob, come to MENU [7]: POWER,
_2yTHen press ( LIV } key to enter the set mode.
3)Clockwise or counterclockwise rotation of
[DIAL] knob to set: HIGHILOW
4)Press [ UNV] key to save the seting,
5)Press [ MENUILOCK ] or [PTT] , EXIT to
‘mal operation
\Whan set the LOW output power, the LOD will
splay he ICON [ LOW] , and not ésplay the
ICON [ HIGH ], when seine HIGH cutout power.
LhDW (DUAL WATCH FEATURE)
“The wanscoiver's Scanning features include a two-
‘channel scanning capabilty, which allows you to
‘operate betwoon UMF channel and VHF channel
in the VFO mode, while periodically checking a
user-defined channel for actly. I one channel
is received the signal, the scanner wil pause on
that channel
Please activate the DW feature according to the
folowing instructions:
4)Press { MENUILOCK } , rotate the. {DIAL}
nab, come to MENU [8]: DW
2yThen press [ UV] key to enter the set mode,
3)Clockwise or counterclockwise rotation of
DIAL] knob to sotOFF (disables the Dual
‘Welch featreVON (actives te Dual Wat fete)
4)Press. [UN] key to save the seting.
5)Press [MENUILOCK } or [PTT] , EXIT to
normal operation,
STEP (Channel Spacing Selection)
The UV-IR's frequency synthesizer provides the
option of bain channel steps of 12.525KtHz per
slep (optional valves cifer depending onthe band
solected). you need to change the chant step
Li
increments, the procedure to dois very easy
‘Press [ MENUILOCK ] , rotate the [DIAL]
‘knob, come to MENU [3]: STEP
2yThen press [UN ] key to enter the set mode.
3)Clockwise or counterclockwise rotation of
[DIAL } knob to select the new frequency step
size (12.525KH2).
4)Press_ [ UNV] key to save the setting.
5)Press [MENUILOCK ] or [PTT] , EXIT to
normal operation
OFFSET (Repeater Operation)
“The UV-IR includes a numberof features which
make repeater operation simple and enjoyable.
+)Press [MENUILOCK ], rotate the [DIAL ]
knob, come to MENU {10} OFFSET
2)Then press [UV ] key to enter the set mode
8}Clockwise or counterclockwise rotation of
[DIAL ] knob to set the offset frequency (0—
37.995M0--69.995M)
4pPress [UN ] key to save the seting.
s)Press [ MENUILOGK ] or [PTT] , EXIT to
rormal operation,
SHIFT (Repeater Shifts)
Depending onthe pat of the band in which you
‘are operating, the repeater shifl may be either
Li‘downward (+) or upward (#). One ofthese icons
‘will appear a ho top of the LCD when repeater
shits have been enabled.
4)Press [ MENUILOCK ] , rotate the [DIAL]
knob, come to MENU [11 SHIFT
‘ayThen press [UN ] key to enter the set mode.
3}Clockwise or counterclockwise rotation of
[DIAL } knob to select the repeater shits: 0+
4yPress [UN ] key to save the seting
s)Press [ MENUILOCK ] or [PTT] , EXIT to
rormal operation.
STE (Tail Tone Elimination)
‘To alminate the annoying aucio caused by cartier
\wave disappearing aftr tho transmittr ends the
‘communication. You should enable the Tall Tone
Elimination. On the contrary, if you want
‘communication va te repeater, you should dssble
the Tal Tone Elimination.
1)Press [ MENU/LOCK } , rotate the [DIAL]
nab, come to MENU [12: STE.
2yTHen press { UNV} key to enter the sat mode.
3)Clockwise or counterclockwise rotation of
[DIAL ] knob to select the STE: ONDOFF
‘Press [UN } key to save the setting
5)Press [MENUILOCK ] or {PTT} , EXIT to
Lh»
WIN (Wide/Narrow Band Selection)
4)Press [ MENUILOCK ] rotate the [DIAL ]
knob, come to MENU [13]: WiN
2)Then press [ UN ] key to enter the set mods.
3)Clockuise or counterclockwise rotation of
[DIAL ] knob to select the WIDEINARROW:
4)Press. [UNV] key to save the seting.
5)Press [ MENUILOCK ] or [PTT] , EXIT to
rmal operation
SAVE (Battery Saver)
‘The UV-3R includes a useful Transmit Battery
Saver, which will automatically lower the power
‘output lovel when the last signal received was
very strong. For exam you aro in tho
immediate vicinity of a repeater station, there
‘generally isn reason to use the high power oulout
inorder to achieve full quiting access to tho
repeater, With the transmit batery saver, the
‘aulomatic selection of Low Power operation
consorves batery drain significantly.
‘To activate the Transmit Battery Saver
4)Press [ MENUILOCK J , rotate the [DIAL]
‘knob, come to MENU [4] SAVE.
2yThen press [ UN ] key to enter the set mods.
3)Clockuise or counterclockwise rotation of
[DIAL ] knob to select the SAVE: ON/OFF
4)Press. [UNV] key to save the seting.
5)Press [ MENUILOCK ] or [PTT] , EXIT to
aTOT (Time-out Timer)
‘The TOT Feature provides a safety switch, which
Imi transmission time to preprogrammed value.
‘This wil consorve battery power by limiting tho
length of transmissions. The TOT defauis 180s,
‘To adjust he timer, seo the instructions bolow:
4)Press [MENUILOCK ] rotate the [DIAL]
nab, come to MENU [15]: TOT
2)Then press [UNV] key to enter the set mode.
3)Clockwise or counterclockwise rotation of
[DIAL] knob to select the TOT:
(OFF/308/605/908)"208/1508/180S
4)Press. [UN ] key to save the setting
‘Press [ MENUILOCK J or [PTT] , EXIT to
normal operation,
SCANM (Scan Mode)
‘The UV.3R allows you to scan the memory
channels, entire operating band, ora parton of
tat band, it wil hat on signals encountered, so
you cantata the station on that frequency. you
ike. To select the scanning mode, please See
below
4)Pross [ MENUILOCK } , rotate the [DIAL]
knob, come to MENU [16} SCANM
2}Then press [UV ] key to enter the set mode.
3}Clockwise or counterclockwise rotation of
LOIAL ] knob fo select the SCANM: TOICO
4)Press [UN ] key to save the soting
')Press [MENUILOCK ] or [PTT], EXIT to
eee —
ELAYM (Repeater Sound Response)
The U = with the Repeater Sound
Response feature. When the feature s activated,
{he handhelavanscelver will near the sound fram
the repeater, that means the handheld wanscoiver
is working via the repaator. Please s00 below fo
fctvate te features
‘)press [ MENUILOGK } rotate the [DIAL]
knob, come fo MENU [17]: RELAYM
2yThen press [ UN ] key to enter the set mods.
S}clockwise or counterclockwise rotation of
[DIAL ] knob to select the RELAYM: ON/OFF
‘4)Press [UNV ] koy to save the sting.
5)Press [MENUILOCK ] or [PTT], EXIT to
‘normal operation,
BCLO (Busy Channel Lock out)
The BOLE provers the rac’ Varsmter
{fom being acvatea if signal strong enough fo
break though tne ‘noise squelch present, On
2 frequency where stations using diferent CTCSS,
67 ¢8 codes may be acive. BELO prevents you
from disrupting nae communicators accdentally
(eeause your radio may be mated by Is owe
‘Tone Decoder) The detail setting forthe BCLO
is OFF. The beiow nstructon fs the procedure to
Bcivato the BCLO:
‘press [MENUILOCK ] rotate me [DIAL]
knob, come lo MENU [18]: BCLO.
ByTher press [UN] kay fo na he st made
S}clockwise or counterclockwise rotation of
TIAL] erat select te BCLO: ONOFF
“Aypress [UNV] key to save toe seting
5)Press [MENULOGK] or [PTT] EXIT to
mal operation
LiADDITIONAL FUNCTIONS AND SETTINGS.
MEMORY CHANNEL STORAGE (Memory Channels 01-99)
Store the Memory Channel according tothe following instructions:
‘@Selec: the desired requency while operating inthe VFO mode. Be sure 10
set up any desired CTCSS or DCS tones, s well as any repeater fet
‘@Press [ FIALERT ] button, then press [UV] key, Channel 07-99
wilfashon the LCD, rotate {DIAL ] knob to store the channel between
channel 07-9.
‘@Press_[ UN] key to save the setting.
‘@Repeat the process above, to store other channels
(Note: Repeater offset tequency shoul be set via programming sofware)
EMERGENCY ALARM FEATURE
Press andhokthe [ IALERT ] butcnabout 12secars, come the Emergency
‘Ae Node, emergency am wilbeheard pres [ PTT] baton, EXIT tonal
operation.
FM RADIO FUNCTION
‘)Press and hold the button { POWER } , come to the FM Radio Mode.
2)Rotate the [ DIAL } knob to adjust te frequency. (The FM broadcast
coverage is 87 0MIH2 to 108.0MH2, Frequency stops 100KHE2)
3)Then press and hold the { POWER ] button, EXIT the FM Radio Mode.
4)Press and hold the [ UNV] to switch the FM radiofrequency mode
‘and the FM racio save channel mode
Lh
‘To save the FM radio channel, please see the following instructions:
‘Under the FM raco Fequency made, set the frequency you want save.
2)Pross tho [ FIALERT } button, and then pross the [ UIV button,
101-15 flashes on the LOD display, rotate the [ DIAL ] knob to save it
3)Press the [ UNV] button to confim saving
In the FM radio mode, the communication between the transceivers
is priority. That means in the FM radio mode, when the signal come,
‘the transceiver will automaticaly ext the FM radio mode.
FM RADIO SCANNING
In the FM Radio made, press [F/ALERT} button, then press
IMENUILOCK] key to scan the complete band. Clockwise or
counterclockwise rotation of {DIAL ] knob to scan the band from low
to igh or from high to low. When searches the ceriain channel, the
scanning willstop atthe channel. Rotate the { DIAL] knob, continuously
to scan rom lw io high o rom high low. Pres any kay to ext the scanning,BAOFENG
TROUBLESHOOTING GUIDE
BAOFENG
SPECIFICATIONS
solutions Freaveney Range | VaFi6:74 UHFAop47oU (alban)
‘rannelCapacty | 95
‘Check battery instalation andor replace bates a
‘Operates Vowage [3.0
Tho bat He is over, replace new one sara ETE
Bator essonsiv ay | Bros
Vent tha the frequen andthe CTCSS you are using Froquony Sabity | 25en(0EH0E)
fre the same a8 toa of your group members GreradTerporaire | a0 - veo
Anienna impedance | #9 0
change your TCSS forthe channol. You alsa need the Dimension [etn Bi
TESS oral the rch in your grup Weight ent 1985
RFRowerRaseg [2
Wesson [FE
Spurious Erieaon | > 058
FM Nise — | #550)
“raemitng Carent | = 148
Soni 1208 SNAD) | 0200
Sarge ROM | ana
‘io Oat Pos@BO
Raciver Crent
Standby Curent
, “w NDECLARATION OF CONFORMITY
We FUJIAN NANAN BAOFENG ELECTRONICS CO.LTD. (Address as
CChangfu Industral Zone, iam Nar’an Quanzhou Fujan,China.) hereby
dedare our product
Product Name: Two Way Radio
Brand Name: BAOFENG
Model Number:UV-3R.
isin complance with the essental requirements and other relevant provisions
of tye RETTE 2006I95/EC, 2004/10B/EC and 98/5/EC, and cares the CE
mark accordingly,
‘Supplementary information:
The product complies with the requirements of:
|EN60950-1:2006+A11 2009; ENSO392-1:2000
TSIEN 300 086-1 V1.1 2008-09); ETSIEN 900 086-2 V1.2.1 (2008-08),
EETSIEN 201 489-1 V18.1 (2008-04); ETSIEN 901 480-5 V1.3.1 (2002-08),
Date: April 15,2011 Signature: WANG SHAO FENG
FUJIAN NAN'AN BAOFENG ELECTRONICS CO.,LTD.
(CHANGFU NDUSTRIAL ZONE XIAMEI NANAN QUANZOU FULIAN CHINA
TEL:+86-595-86752889/86767889 FAX:+86-595-B6753869
E-Mailtbaofeng@263.net_hitp:/ww.powerphone.com.cn