CALIBRATION CERTIFICATE daa kes
Be sie Seal issued
Stlas Copco Tentec Limited Part of the Atlas Copco Group
= Unit F1, innovation drive, Pendeford,
Wolverhampton
West Midlands, WV9 5GA, UK
Certificate No: $-4693 Calibration Date: 05/08/2020 ‘Approved Signatory
Calibration Engineer: Adrian Punnett Signed: 7&7 — a ee
]
‘Too! Description Customer
Description: Hydraulic Torque Wrench POWER TOOLS DISTRIBUTION N.V (PTD)
: INDUSTRIELAAN 40
Model: RT-25SQDR bs7s0 HOBSELT
Serial No: 15/16003-008 BELGIUM
+32 (0) 89510414,
TSD 40014 SIN (6722)
Calibrated by Atlas Copco BLM - Accredia 0 to 40,000 bff Torque transducer
Accreditation - LAT 059 From 10% to 100%: 0.1%
From 0% to 10%: £2 civsions (10 LB-FT)
Pressure Transducers: TSD 10KPT RHYD S/N (170393)
Calibrated by CHAMOIS METROLOGY - (00 10000 Pst Pressure transducer
From 10% to 100%: 0.1%
UKAS Accreditation - 0622 From 0% to 10%: #2 divisions (2 Pei)
joplay Unit: TSD 6500-2 SIN (20946
Calibrated by - Atlas Copco BLM - Accredia Max Capacity
“Torque = 40,000 bt ft
Accreditation - LAT 059 Pressure - 10,000 Psi
Reaction Foot: RA-15/16003-008
Calibration Procedure
Calibration done in accordance with procedure "TCP6 -REVB" based on standard ISO 6789: 2003
Traceability
‘All measuring equipment used for calibration purposes is traceable to National or Internationally recognised
standards
‘Test Conditions
“Temperature: 22.36 Humidity: 54.54
‘The temperature did not fluctuate by more than +/- 1° Celsius during the measurement series
This cerlicate provides traceabilty of measurement tothe SI system of units anclor to units of measurement realised atthe National
Physical Laboretory or other recognised national metrology institutes. This certificate may not be repoduced other than infu, except with
‘the prior written aproval of the issuing laboratory.
Intemet: wwwtentec.net Telephone +44 (0)121 524 1980Page 2 of 2
Certificate No: S-4893
‘Model: RT-258Q DR
Serial No: 16/16003-008
CALIBRATION CERTIFICATE
Calibration Date: 05/08/2020
2000 | 138 | [1998.6|138
6315.0 [5260.0 [5865.0 [5255.0 (5245.0 [5388.0 | [+/-] 3.00%
6000 | 414 | |5999 [474
17136.0 |16005.0 |16010.0 |16010.0 |15990.0 |16230.0| [+/-] 3.00 %
10000] 689 | |9999 689
'26730.0 |26810.0 |26840.0 |26795.0 |26795.0 |26794.0] [+/-] 3.00 %
2000 | 138 | |1998.6/138 [7206.2 (7131.6 [7951.9 |7124.8 |7111.3 (7305.1 _| [+] 3.00%
6000 | 414 | [5999 [414
'23231.9 |21699.9 |21706.6 |21706.6 |21679.5 |22004.9| [+/-] 3.00 %
10000] 689 | |s999 |689
36241,0 |36349.5 |36390.2 |36329.1 |36329.1 /36327.8/ [+/-] 3.00%
40,000
35,000
‘900 2000
Intemet: www tentec.net
‘joo 4000 ~=«s000~~—«6000 ~—«*7000~=«=«800D «S000 = «10000
Pressure (PSI)
‘Thiscalration certieate eval for 12 months
from stock despatch date
| Place oss: Power ToosDistrbution Nv
Stock derpatch date: AB/OW| Loky —
Santee S49, LL
‘Telephone +44 (0)121 524 1990Tentec Limited
Dees Unit Ft
Innovation Drive
Atlas Copco Pondefor, Wolverhampton
WV9 SGA
Telephone +44 (0)121 524 1990
ATLAS COPCO
POWER TOOLS DISTRIBUTION Internet: www.tentec.net
INDUSTRIELAAN 40 email: bolting@uk.atlascopco.com
8.3730 HOESALT
BELGIUM Customer ON 4510243197
Our Ref 202123
BE0443676020
Advice Note 05/08/2020
Page 1/1
certificate of conformity & pressure test certificate
Qty Description Part Number
1 Square Drive 18434201025
RT-25
SIN. 18/16003-008
EC DECLARATION OF INCORPORATION
Hydraulic Torque Wrench The equipment listed left are intended for assembly with, bolt tensioning hose, bolt tensioners, and
bolt tensioning pumps supplied or approved for use by Tentec Ltd, to constitute machinery covered
by Directive 2006/42/EC. They must not be placed into service unti all items have been declared in
‘conformity withthe provisions of the 2006/42/EC Directive. The following EHSR’s sections covered
by annex C of the directive have been complied with. Section 1,3 & 4. Assembly instructions are
provided by Tentec in accordance with Annex VI. A technical document is compiled in accordance
with Annex Vil of the Directive,
BLOCK NAME DAVID JONES
BLOCK POSITION GENERAL MANAGER
Freer
We herewith certify based on pressure testing and dimensionel inspection that the items supplied under the above
purchase order are in accordance with the requirements ofthe orcer in particular to
‘a) The fullment of material requirements
1) The fullment ofthe required accuracy to, gauge, tolerances, quality surface
(0) The fullment of performance
Authorised Signature Looassy late ‘Tap. 420269