Professional Documents
Culture Documents
Features
Easy Design-in
Temperature Compensated
Calibrated & Amplified Output
Low Cost
Applications
Process Control
HVAC
Consumer Electronics
Medical Devices
Description
The 33A Series incorporates a si licon piezoresistive
pressure sensor and signal conditioning ASIC in a 6-pin DIL
plastic housing for easy through hole board assembly. A surface
mount version is also available. It provides a temperature
compensated, calibrated pressure solution for high volume
applications at an affordable cost.
Pressure ranges are available from 0.15 to 100 psig. Ratiometric
output at 5V excitation is 0.5 to 4.5 V. Pressure connection is
through Tygon tube on the pressure port.
Custom calibrations are available please contact the factory for
details.
Selection Table Pressure Sensors
Measurement Range
Type Part Name Input Voltage Output
PSI mmHg
33A-015G-2210 0 ~ 15 0 ~ 775.7
33A-030G-2210 0 ~ 30 0 ~ 1551.4
33A-050G-2210 0 ~ 50 0 ~ 2585.7
33A-007I-2210 0 ~ -7 0 ~ -362
Vacuum
4.5V
3.5V
t
u tpu
geO
2.5V lta
Vo
1.5V
0.5V
0V Pressure
0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
(Vin X 80%)
Output Voltage = X Pressure Applied + 0.5
Pressure Range
(5V X 80%)
For 33A-007G-2210, 3.814V = X 5.8 PSI + 0.5
7 PSI
33A-L15G-2210 ANALOG
OUTPUT
0.5 ~ 4.5V Output, 0.15 PSI, Gage Type
Characteristics
Unless otherwise specified, all parameters are measured at 25 °C and excitation of 5 Vdc
Parameters Min Typ Max Unit
Supply Voltage 4.75 5.00 5.25 Vdc
Supply Current 3 mA
Measurement Range 0 0.15 psi
Offset 0.412 0.50 0.588 Vdc
Span 4.0 Vdc
Output Current of Buffer 1 2 mA
Accuracy ±2.2 %FS
Over Pressure 3X Rated Pressure
Temp - Compensating 0 50 °C
Temp - Operating -20 +80 °C
Temp - Storage -40 +125 °C
NOTES:
1. Accuracy includes non-linearity, hysterisis, TCS and TCO from 10 to 50 deg C, best fit straight line definition
2. Wetted material contains RTV, siliocn and PPS
3. Zeroing at installation is required
4. Output is ratiometric to supply voltage
Pin Connection
PIN # Description
Top View Bottom View 1 N.C.
10.0
2 N.C.
6 5 4 1 2 3
3 GND
Atmospheric 4 VDD
Vent Port
8.6
1 2 3 6 5 4 NOTE.
Note:
Soldering of lead pins: 250 °C for 5 sec max.
N.C. pins must be left floating
A 0.1uf capacitor must be
connected between VDD
Ordering Information and GND
33A L15 G 2 2 10
Characteristics
Unless otherwise specified, all parameters are measured at 25 °C and excitation of 5 Vdc
Parameters Min Typ Max Unit
Supply Voltage 4.75 5.00 5.25 Vdc
Supply Current 3 mA
Measurement Range 0 1 psi
Offset 0.428 0.50 0.572 Vdc
Span 4.0 Vdc
Output Current of Buffer 1 2 mA
Accuracy ±1.8 %FS
Over Pressure 3X Rated Pressure
Temp - Compensating 0 50 °C
Temp - Operating -20 +80 °C
Temp - Storage -40 +125 °C
NOTES:
1. Accuracy includes non-linearity, hysterisis, TCS and TCO from 10 to 50 deg C, best fit straight line definition
2. Wetted material contains RTV, siliocn and PPS
3. Zeroing at installation is required
4. Output is ratiometric to supply voltage
Pin Connection
PIN # Description
Top View Bottom View 1 N.C.
10.0
2 N.C.
6 5 4 1 2 3
3 GND
Atmospheric 4 VDD
Vent Port
8.6
1 2 3 6 5 4 NOTE.
Note:
Soldering of lead pins: 250 °C for 5 sec max.
N.C. pins must be left floating
A 0.1uf capacitor must be
connected between VDD
Ordering Information and GND
33A 001 G 2 2 10
Characteristics
Unless otherwise specified, all parameters are measured at 25 °C and excitation of 5 Vdc
Parameters Min Typ Max Unit
Supply Voltage 4.75 5.00 5.25 Vdc
Supply Current 3 mA
Measurement Range 0 2 psi
Offset 0.428 0.50 0.572 Vdc
Span 4.0 Vdc
Output Current of Buffer 1 2 mA
Accuracy ±1.8 %FS
Over Pressure 3X Rated Pressure
Temp - Compensating 0 50 °C
Temp - Operating -20 +80 °C
Temp - Storage -40 +125 °C
NOTES:
1. Accuracy includes non-linearity, hysterisis, TCS and TCO from 10 to 50 deg C, best fit straight line definition
2. Wetted material contains RTV, siliocn and PPS
3. Zeroing at installation is required
4. Output is ratiometric to supply voltage
Pin Connection
PIN # Description
Top View Bottom View 1 N.C.
10.0
2 N.C.
6 5 4 1 2 3
3 GND
Atmospheric 4 VDD
Vent Port
8.6
1 2 3 6 5 4 NOTE.
Note:
Soldering of lead pins: 250 °C for 5 sec max.
N.C. pins must be left floating
A 0.1uf capacitor must be
connected between VDD
Ordering Information and GND
33A 002 G 2 2 10
Characteristics
Unless otherwise specified, all parameters are measured at 25 °C and excitation of 5 Vdc
Parameters Min Typ Max Unit
Supply Voltage 4.75 5.00 5.25 Vdc
Supply Current 3 mA
Measurement Range 0 5 psi
Offset 0.428 0.50 0.572 Vdc
Span 4.0 Vdc
Output Current of Buffer 1 2 mA
Accuracy ±1.8 %FS
Over Pressure 3X Rated Pressure
Temp - Compensating 0 50 °C
Temp - Operating -20 +80 °C
Temp - Storage -40 +125 °C
NOTES:
1. Accuracy includes non-linearity, hysterisis, TCS and TCO from 10 to 50 deg C, best fit straight line definition
2. Wetted material contains RTV, siliocn and PPS
3. See ordering information for list of available pressure ranges
4. Output is ratiometric to supply voltage
Pin Connection
PIN # Description
Top View Bottom View 1 N.C.
10.0
2 VDD
6 5 4 1 2 3
3 GND
Atmospheric 4 VDD
Vent Port
8.6
1 2 3 6 5 4 NOTE.
Note:
Soldering of lead pins: 250 °C for 5 sec max.
N.C. pins must be left floating
A 0.1uf capacitor must be
connected between VDD
Ordering Information and GND
33A 005 G 2 2 10
Characteristics
Unless otherwise specified, all parameters are measured at 25 °C and excitation of 5 Vdc
Parameters Min Typ Max Unit
Supply Voltage 4.75 5.00 5.25 Vdc
Supply Current 3 mA
Measurement Range 0 7 psi
Offset 0.428 0.50 0.572 Vdc
Span 4.0 Vdc
Output Current of Buffer 1 2 mA
Accuracy ±1.8 %FS
Over Pressure 3X Rated Pressure
Temp - Compensating 0 50 °C
Temp - Operating -20 +80 °C
Temp - Storage -40 +125 °C
NOTES:
1. Accuracy includes non-linearity, hysterisis, TCS and TCO from 10 to 50 deg C, best fit straight line definition
2. Wetted material contains RTV, siliocn and PPS
3. See ordering information for list of available pressure ranges
4. Output is ratiometric to supply voltage
Pin Connection
PIN # Description
Top View Bottom View 1 N.C.
10.0
2 N.C.
6 5 4 1 2 3
3 GND
Atmospheric 4 VDD
Vent Port
8.6
1 2 3 6 5 4 NOTE.
Note: N.C. pins must be left floating
Soldering of lead pins: 250 °C for 5 sec max.
A 0.1uf capacitor must be
connected between VDD
Ordering Information and GND
33A 007 G 2 2 10
Characteristics
Unless otherwise specified, all parameters are measured at 25 °C and excitation of 5 Vdc
Parameters Min Typ Max Unit
Supply Voltage 4.75 5.00 5.25 Vdc
Supply Current 3 mA
Measurement Range 0 10 psi
Offset 0.428 0.50 0.572 Vdc
Span 4.0 Vdc
Output Current of Buffer 1 2 mA
Accuracy ±1.8 %FS
Over Pressure 1.5X Rated Pressure
Temp - Compensating 0 50 °C
Temp - Operating -20 +80 °C
Temp - Storage -40 +125 °C
NOTES:
1. Accuracy includes non-linearity, hysterisis, TCS and TCO from 10 to 50 deg C, best fit straight line definition
2. Wetted material contains RTV, siliocn and PPS
3. See ordering information for list of available pressure ranges
4. Output is ratiometric to supply voltage
Pin Connection
PIN # Description
Top View Bottom View 1 N.C.
10.0
2 VDD
6 5 4 1 2 3
3 GND
Atmospheric 4 VDD
Vent Port
8.6
1 2 3 6 5 4 NOTE.
Note: N.C. pins must be left floating
Soldering of lead pins: 250 °C for 5 sec max.
A 0.1uf capacitor must be
connected between VDD
Ordering Information and GND
33A 010 G 2 2 10
Characteristics
Unless otherwise specified, all parameters are measured at 25 °C and excitation of 5 Vdc
Parameters Min Typ Max Unit
Supply Voltage 4.75 5.00 5.25 Vdc
Supply Current 3 mA
Measurement Range 0 15 psi
Offset 0.428 0.50 0.572 Vdc
Span 4.0 Vdc
Output Current of Buffer 1 2 mA
Accuracy ±1.8 %FS
Over Pressure 3X Rated Pressure
Temp - Compensating 0 50 °C
Temp - Operating -20 +85 °C
Temp - Storage -40 +125 °C
NOTES:
1. Accuracy includes non-linearity, hysterisis, TCS and TCO from 10 to 50 deg C, best fit straight line definition
2. Wetted material contains RTV, siliocn and PPS
3. See ordering information for list of available pressure ranges
4. Output is ratiometric to supply voltage
Pin Connection
PIN # Description
Top View Bottom View 1 N.C.
10.0
2 N.C.
6 5 4 1 2 3
3 GND
Atmospheric 4 VDD
Vent Port
8.6
1 2 3 6 5 4 NOTE.
Note: N.C. pins must be left floating
Soldering of lead pins: 250 °C for 5 sec max.
A 0.1uf capacitor must be
connected between VDD
Ordering Information and GND
33A 015 G 2 2 10
Characteristics
Unless otherwise specified, all parameters are measured at 25 °C and excitation of 5 Vdc
Parameters Min Typ Max Unit
Supply Voltage 4.75 5.00 5.25 Vdc
Supply Current 3 mA
Measurement Range 0 30 psi
Offset 0.428 0.50 0.572 Vdc
Span 4.0 Vdc
Output Current of Buffer 1 2 mA
Accuracy ±1.8 %FS
Over Pressure 3X Rated Pressure
Temp - Compensating 0 50 °C
Temp - Operating -20 +80 °C
Temp - Storage -40 +125 °C
NOTES:
1. Accuracy includes non-linearity, hysterisis, TCS and TCO from 10 to 50 deg C, best fit straight line definition
2. Wetted material contains RTV, siliocn and PPS
3. See ordering information for list of available pressure ranges
4. Output is ratiometric to supply voltage
Pin Connection
PIN # Description
Top View Bottom View 1 N.C.
10.0
2 N.C.
6 5 4 1 2 3
3 GND
Atmospheric 4 VDD
Vent Port
8.6
1 2 3 6 5 4 NOTE.
Note: N.C. pins must be left floating
Soldering of lead pins: 250 °C for 5 sec max.
A 0.1uf capacitor must be
connected between VDD
Ordering Information and GND
33A 030 G 2 2 10
Characteristics
Unless otherwise specified, all parameters are measured at 25 °C and excitation of 5 Vdc
Parameters Min Typ Max Unit
Supply Voltage 4.75 5.00 5.25 Vdc
Supply Current 3 mA
Measurement Range 0 50 psi
Offset 0.428 0.50 0.572 Vdc
Span 4.0 Vdc
Output Current of Buffer 1 2 mA
Accuracy ±1.8 %FS
Over Pressure 3X Rated Pressure
Temp - Compensating 0 50 °C
Temp - Operating -20 +80 °C
Temp - Storage -40 +125 °C
NOTES:
1. Accuracy includes non-linearity, hysterisis, TCS and TCO from 10 to 50 deg C, best fit straight line definition
2. Wetted material contains RTV, siliocn and PPS
3. See ordering information for list of available pressure ranges
4. Output is ratiometric to supply voltage
Pin Connection
PIN # Description
Top View Bottom View 1 N.C.
10.0
2 N.C.
6 5 4 1 2 3
3 GND
Atmospheric 4 VDD
Vent Port
8.6
1 2 3 6 5 4 NOTE.
Note:
Soldering of lead pins: 250 °C for 5 sec max.
N.C. pins must be left floating
A 0.1uf capacitor must be
connected between VDD
Ordering Information and GND
33A 050 G 2 2 10
Characteristics
Unless otherwise specified, all parameters are measured at 25 °C and excitation of 5 Vdc
Parameters Min Typ Max Unit
Supply Voltage 4.75 5.00 5.25 Vdc
Supply Current 3 mA
Measurement Range 0 100 psi
Offset 0.428 0.50 0.572 Vdc
Span 4.0 Vdc
Output Current of Buffer 1 2 mA
Accuracy ±1.8 %FS
Over Pressure 3X Rated Pressure
Temp - Compensating 0 50 °C
Temp - Operating -20 +85 °C
Temp - Storage -40 +125 °C
NOTES:
1. Accuracy includes non-linearity, hysterisis, TCS and TCO from 10 to 50 deg C, best fit straight line definition
2. Wetted material contains RTV, siliocn and PPS
3. See ordering information for list of available pressure ranges
4. Output is ratiometric to supply voltage
Pin Connection
PIN # Description
Top View Bottom View 1 N.C.
10.0
2 N.C.
6 5 4 1 2 3
3 GND
Atmospheric 4 VDD
Vent Port
8.6
1 2 3 6 5 4 NOTE.
Note: N.C. pins must be left floating
Soldering of lead pins: 250 °C for 5 sec max.
A 0.1uf capacitor must be
connected between VDD
Ordering Information and GND
33A 100 G 2 2 10
Characteristics
Unless otherwise specified, all parameters are measured at 25 °C and excitation of 5 Vdc
Parameters Min Typ Max Unit
Supply Voltage 4.75 5.00 5.25 Vdc
Supply Current 3 mA
Measurement Range 0 150 psi
Offset 0.428 0.50 0.572 Vdc
Span 4.0 Vdc
Output Current of Buffer 1 2 mA
Accuracy ±1.8 %FS
Over Pressure 1.2X Rated Pressure
Temp - Compensating 0 50 °C
Temp - Operating -20 +80 °C
Temp - Storage -40 +125 °C
NOTES:
1. Accuracy includes non-linearity, hysterisis, TCS and TCO from 10 to 50 deg C, best fit straight line definition
2. Wetted material contains RTV, siliocn and PPS
3. See ordering information for list of available pressure ranges
4. Output is ratiometric to supply voltage
Pin Connection
PIN # Description
Top View Bottom View 1 N.C.
10.0
2 N.C.
6 5 4 1 2 3
3 GND
Atmospheric 4 VDD
Vent Port
8.6
1 2 3 6 5 4 NOTE.
Note: N.C. pins must be left floating
Soldering of lead pins: 250 °C for 5 sec max.
A 0.1uf capacitor must be
connected between VDD
Ordering Information and GND
33A 150 G 2 2 10
Characteristics
Unless otherwise specified, all parameters are measured at 25 °C and excitation of 5 Vdc
Parameters Min Typ Max Unit
Supply Voltage 4.75 5.00 5.25 Vdc
Supply Current 3 mA
Measurement Range -7 0 psi
Offset 0.428 0.50 0.572 Vdc
Span 4.0 Vdc
Output Current of Buffer 1 2 mA
Accuracy ±1.8 %FS
Over Pressure 3X Rated Pressure
Temp - Compensating 0 50 °C
Temp - Operating -20 +80 °C
Temp - Storage -40 +125 °C
NOTES:
1. Accuracy includes non-linearity, hysterisis, TCS and TCO from 10 to 50 deg C, best fit straight line definition
2. Wetted material contains RTV, siliocn and PPS
3. See ordering information for list of available pressure ranges
4. Output is ratiometric to supply voltage
Pin Connection
PIN # Description
Top View Bottom View 1 N.C.
10.0
2 N.C.
6 5 4 1 2 3
3 GND
Atmospheric 4 VDD
Vent Port
8.6
1 2 3 6 5 4 NOTE.
Note: N.C. pins must be left floating
Soldering of lead pins: 250 °C for 5 sec max.
A 0.1uf capacitor must be
connected between VDD
Ordering Information and GND
33A 007 I 2 2 10
Characteristics
Unless otherwise specified, all parameters are measured at 25 °C and excitation of 5 Vdc
Parameters Min Typ Max Unit
Supply Voltage 4.75 5.00 5.25 Vdc
Supply Current 3 mA
Measurement Range -10 0 psi
Offset 0.428 0.50 0.572 Vdc
Span 4.0 Vdc
Output Current of Buffer 1 2 mA
Accuracy ±1.8 %FS
Over Pressure 3X Rated Pressure
Temp - Compensating 0 50 °C
Temp - Operating -20 +80 °C
Temp - Storage -40 +125 °C
NOTES:
1. Accuracy includes non-linearity, hysterisis, TCS and TCO from 10 to 50 deg C, best fit straight line definition
2. Wetted material contains RTV, siliocn and PPS
3. See ordering information for list of available pressure ranges
4. Output is ratiometric to supply voltage
Pin Connection
PIN # Description
Top View Bottom View 1 N.C.
10.0
2 N.C.
6 5 4 1 2 3
3 GND
Atmospheric 4 VDD
Vent Port
8.6
1 2 3 6 5 4 NOTE.
Note: N.C. pins must be left floating
Soldering of lead pins: 250 °C for 5 sec max.
A 0.1uf capacitor must be
connected between VDD
Ordering Information and GND
33A 010 I 2 2 10
Characteristics
Unless otherwise specified, all parameters are measured at 25 °C and excitation of 5 Vdc
Parameters Min Typ Max Unit
Supply Voltage 4.75 5.00 5.25 Vdc
Supply Current 3 mA
Pressure Range -15 0 psi
Offset 0.428 0.50 0.572 Vdc
Span 4.0 Vdc
Output Current of Buffer 1 2 mA
Accuracy ±1.8 %FS
Over Pressure 3X Rated Pressure
Temp - Compensating 0 50 °C
Temp - Operating -20 +85 °C
Temp - Storage -40 +125 °C
NOTES:
1. Accuracy includes non-linearity, hysterisis, TCS and TCO from 10 to 50 deg C, best fit straight line definition
2. Wetted material contains RTV, siliocn and PPS
3. See ordering information for list of available pressure ranges
4. Output is ratiometric to supply voltage
Pin Connection
PIN # Description
Top View Bottom View 1 N.C.
10.0
2 N.C.
6 5 4 1 2 3
3 GND
Atmospheric 4 VDD
Vent Port
8.6
1 2 3 6 5 4 NOTE.
Note: N.C. pins must be left floating
Soldering of lead pins: 250 °C for 5 sec max.
A 0.1uf capacitor must be
connected between VDD
Ordering Information and GND
33A 015 I 2 2 10
10.2±0.2
8.6±0.1
10
C0.5
3.0
6
R 0.5
(1.15)
(0.7)
3.3
4.9
1.2
5-15° 0.2
0.5
2.54
5.08
6 5 4 1 2 3
0.8
Atmospheric
Vent Port
8.6
A XXXG 2210
xxx
1 2 3 6 5 4
Basic Schematic
NOTE.
N.C. pins must be left floating
A 0.1uf capacitor must be connected between VDD and GND
5V
33A-005G-2210
33A-010G-2210
CAP
0.1uF
PIN # Description
1 6
2 5 1 N.C.
3 4 2 VDD
3 GND
4 VDD
5 VOUT
Note: 6 GND
Soldering of lead pins: 250 °C for 5 sec max.
5V
33A-002G-2210
33A-007G-2210
CAP
33A-007I-2210
0.1uF
PIN # Description
1 6
2 5 1 N.C.
3 4 2 N.C.
3 GND
4 VDD
5 VOUT
Note: 6 GND
Soldering of lead pins: 250 °C for 5 sec max.
33A-L15G-2210 33A-100G-2210
5V 33A-001G-2210 33A-150G-2210
33A-015G-2210 33A-010I-2210
33A-030G-2210 33A-015I-2210
CAP 33A-050G-2210
0.1uF
PIN # Description
1 6
2 5 1 N.C.
3 4 2 N.C.
3 GND
4 VDD
5 VOUT
Note: 6 N.C.
Soldering of lead pins: 250 °C for 5 sec max.
Contact us
NANOSENTECH Co., Ltd.
#805, Doosan Venture Digm B/D, Pyeongchon-dong,
Dongan-gu, Anyang-si, Gyeonggi-do, KOREA (ZIP 431-755)
Tel : +82-31-478-3625 Fax : +82-31-478-3628
E-mail : info@nanosentech.co.kr URL : www.nanosentech.co.kr