Professional Documents
Culture Documents
fm 1 ページ 2014年4月30日 水曜日 午後2時9分
REGISTRATION MANUAL
FOR IMMOBILIZER
Page
1 IMPORTANT ...................................................................................................................3
2 Immobilizer Application Chart .........................................................................................4
3 What to Prepare ..............................................................................................................4
3-1 Special Tool.......................................................................................................4
3-2 Others ...............................................................................................................4
4 A type ..............................................................................................................................5
4-1 Registering Immobilizer Key..............................................................................6
4-2 Immobilizer system: Correspondence table at the time of parts lost or
failure .................................................................................................. 11
4-3 Correspondence table when registration is not possible.................................12
5 B type ............................................................................................................................14
5-1 Adding Keys ....................................................................................................15
5-2 Registering Body Integrated Unit ....................................................................18
5-3 Registering Engine ECM.................................................................................21
5-4 Registering Combination Meter or Security CU ..............................................22
5-5 Registering Remote Control Engine Starter....................................................24
5-6 Deleting Key ID ...............................................................................................25
5-7 Immobilizer system: Correspondence table at the time of parts lost or
failure .................................................................................................. 28
5-8 Correspondence table when registration is not possible.................................31
6 C type............................................................................................................................37
6-1 Adding Access Keys........................................................................................39
6-2 Registering Collation CU.................................................................................42
6-3 Registering the Steering Lock CU or ID Code Box .........................................46
6-4 Registering the Engine ECM...........................................................................49
6-5 Readout the Number of Access Key Registration ...........................................51
6-6 Delete the Access Key ID................................................................................52
6-7 Registering Remote Control Engine Starter....................................................55
6-8 Registering Body Integrated Unit or Combination Meter.................................57
6-9 Keyless access with push button start system (except for North America):
Correspondence table at the time of parts failure ....................................... 58
6-10 Correspondence table when registration is not possible.................................65
7 D type............................................................................................................................74
7-1 Adding Access Keys........................................................................................76
7-2 Registering Keyless Access CU......................................................................78
7-3 Registering the Steering Lock CU or ID Code Box .........................................81
7-4 Registering the Engine ECM...........................................................................83
7-5 Readout the Number of Access Key Registration ...........................................84
7-6 Delete the Access Key ID................................................................................86
S1001BE.fm 2 ページ 2014年4月30日 水曜日 午後2時9分
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 3 ページ 2014年4月30日 水曜日 午後2時9分
IMPORTANT
REGISTRATION MANUAL FOR IMMOBILIZER
1 IMPORTANT
This manual and the procedures within are
provided for use by Subaru repair professionals
and/or Automotive Security Professionals
registered through the professional locksmiths
working under local regulations for the sole
purpose of lawfully providing key and immobilizer
repair or replacement at the request of the lawful
vehicle owner, lessee or their authorized agent.
Use by unauthorized personnel is strictly
prohibited.
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 4 ページ 2014年4月30日 水曜日 午後2時9分
3 What to Prepare
3-1 Special Tool
Subaru Select Monitor III Kit
3-2 Others
• All keys to be registered or all keys or access
keys that are already registered.
• Security ID (security tag) (Vehicle type that is
originally provided with a security ID)
• The remote controller for remote control engine
starter (vehicle type with remote control engine
starter)
• Registration command (Vehicle type that is
originally provided with a security ID)
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 5 ページ 2014年4月30日 水曜日 午後2時9分
A type
REGISTRATION MANUAL FOR IMMOBILIZER
4 A type C: Caution
Vehicle that does NOT have a keyless access with • The security ID and registration command
push button start system and is originally provided must be handled as confidential information
with a security ID (security tag) and shall not be announced to outsiders.
• When you install wireless radios or car
A: Structure phones, make sure that the immobilizer
An immobilizer system consists of the following system is not influenced by their electric
components: Combination meter or security CU waves.
(for a model with security CU), immobilizer • Do not operate cell phones or wireless radios
indicator (in the combination meter), body
or the like when either trouble diagnosis or
integrated unit, ECM, ignition key, and immobilizer
immobilizer registration is in progress.
antenna.
• During immobilizer registration, do not bring
B: Operation a key with a different ID close to the ignition
When the ignition key incorporating a transponder switch. When the key is on a keychain,
is inserted into the key cylinder, the body integrated remove it from the chain before start of
unit receives the ignition key ID via the immobilizer diagnosis. When there are several keys on
antenna.
one keychain, remove them from the
The received key ID is collated with the key ID
keychain and use them individually for the
stored in the memory of the body integrated unit. At
work.
the same time, the meter IDs (SCU IDs) stored in
the memory of the body integrated unit and • When the engine cannot be started with a
combination meter (or the security CU) are registered key, pull the ignition key from the
collated. ignition switch, wait approximately one
Then, the engine IDs stored in the memory of the second until the immobilizer warning lamp
ECM and body integrated unit are collated. starts flashing, and then turn the ignition key
If the IDs do not match within the specified period of slowly to start the engine.
time after the RPM of the engine reaches the • Confirm that the battery voltage is 11 V or
specified RPM, the engine stops.
more and execute each mode.
If the IDs do not match, the engine stops within a
couple of seconds. If the engine does not start as a • During immobilizer registration, make sure
result of a mismatch of the IDs, the immobilizer connectors do not get disconnected.
indicator in the combination meter turns on to
indicate that the immobilizer is active. When the
ignition key is removed, the immobilizer is activated
and the immobilizer indicator lamp flashes to
generate an alert notifying people around the
vehicle that it is protected by the immobilizer.
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 6 ページ 2014年4月30日 水曜日 午後2時9分
A type
REGISTRATION MANUAL FOR IMMOBILIZER
4-1 Registering Immobilizer Key 4) Click the [YES] button if the System Check
screen is displayed.
The immobilizer key must be registered to do any of
the following. When the registration procedure is
performed, all IDs stored in the memory are deleted
from the registration.
• Add and register an ignition key. IM-00404
• Delete the ID of the lost ignition key.
• Replace the body integrated unit.
• Replace the ECM.
• Replace the combination meter.
IM-00404
• Register the remote control engine starter for the
immobilizer. Note:
Audio System is the specification only for the U.K.
1) Start the PC application according to section 5) On the next screen, confirm the system is
"Starting Up the System" and display the Main keyless access with push button start system.
Menu screen. (Refer to "PC application help for Click the [NO] button.
Subaru Select Monitor".)
2) On the Main Menu, select [All other models].
IM-00405
IM-00405
Note:
IM-00491
The term [smart system] that appears on this
3) Select [Immobilizer] from the item selection screen is synonymous with the term [keyless
dialog box. access with push button start system] used in this
text.
6) Click [YES] after confirming if the ignition switch
is ON, as following screen will be displayed.
Note:
When an error screen is displayed, refer to No. 1 in
"4-3 Correspondence table when registration is not
possible".
IM-00492
IM-00406
IM-00406
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 7 ページ 2014年4月30日 水曜日 午後2時9分
A type
REGISTRATION MANUAL FOR IMMOBILIZER
7) In response to the compliance verification 10) Input the security ID and then click the [OK]
dialog box that appears, click the [OK] button. button.
IM-00407 IM-00410
IM-00407 IM-00410
8) Input the teaching operation code, and then 11) Stand by as the security ID is being collated.
click the [OK] button. Note:
Note: When an error screen is displayed, refer to No. 2 in
If the menu screen is displayed instead of the "4-3 Correspondence table when registration is not
command input screen, the vehicle is B type. See possible".
the procedures for B type vehicle.
IM-00411
IM-00408
IM-00411
IM-00408
12) In response to the key registration confirmation
Note: screen dialog box that appears, click the [OK]
When you wish to return to the Main Menu screen, button.
click the [QUIT] button. Note:
9) On the registration mode confirmation dialog When an error screen is displayed, refer to No. 3 in
box that appears, click the [OK] button. "4-3 Correspondence table when registration is not
possible".
IM-00409
IM-00412
IM-00409
IM-00412
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 8 ページ 2014年4月30日 水曜日 午後2時9分
A type
REGISTRATION MANUAL FOR IMMOBILIZER
13) Stand by as the key is registered. 15) Turn off the ignition switch, and then change the
Note: key to one to be registered.
When an error screen is displayed, refer to No. 3 in Note:
"4-3 Correspondence table when registration is not You need to change key within about 30 seconds.
possible". The screens shown in this section may be different
depending on the model being used. In such a
case, follow the instructions shown on the screens.
IM-00413
IM-00415
IM-00413
IM-00417
IM-00417
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 9 ページ 2014年4月30日 水曜日 午後2時9分
A type
REGISTRATION MANUAL FOR IMMOBILIZER
18) Stand by as the key is registered. 21) The screen shown below will appear if
Note: registration ends normally. If you have another
When an error screen is displayed, refer to No. 4 in key to be registered, click the [OK] button. If you
"4-3 Correspondence table when registration is not do not have any more keys to be registered,
possible". click the [Cancel] button and advance to step
23.
Caution:
If you have no more keys to be registered, make
IM-00418 sure to click the [Cancel] button to quit the
registration operation.
If you quit the operation without clicking the
[Cancel] button, the immobilizer indicator
blinks differently than usual. In such a case,
IM-00418 register the immobilizer again.
19) The screen shown below will appear if
registration ends normally. If you have another
key to be registered, click the [OK] button. If you
do not have any more keys to be registered, IM-00420
click the [Cancel] button and advance to step
23.
Caution:
If you have no more keys to be registered, make
IM-00420
sure to click the [Cancel] button to quit the
registration operation. 22) Repeat steps 15 through 18.
If you quit the operation without clicking the 23) The remote control engine starter registration
[Cancel] button, the immobilizer indicator mode confirmation dialog box will be displayed.
blinks differently than usual. In such a case, If you have another key to be registered, click
register the immobilizer again. the [OK] button. If you do not have any more
keys to be registered, click the [Cancel] button
and move on to step 26.
Note:
IM-00419 The screens shown in this section may be different
depending on the model being used. In such a
case, follow the instructions shown on the screens.
IM-00419
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 10 ページ 2014年4月30日 水曜日 午後2時9分
A type
REGISTRATION MANUAL FOR IMMOBILIZER
IM-00422
IM-00422
IM-00423
Turn off the engine
And con firm res tart engine
Press OK
IM-00423
10
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 11 ページ 2014年4月30日 水曜日 午後2時9分
Å`
SIE-id::
4-2 Immobilizer system: Correspondence table at the time of parts lost or failure
Vehicle-id:
1. Parts replacement table
Note:
To register an immobilizer, your security ID is required. (*3)
Parts failed/lost Parts required to replace or prepared when items on the left fail Procedures to perform after parts replacement
Key Meter *4 Meter *4
Body Body
or or
ECM integrated Key ECM integrated (1) (2)
Not all All Security CU Security CU
unit unit
*5 *5
X Keys you want to register (registered key or new key) Registering Immobilizer Key
X New key you want to register Registering Immobilizer Key
1 parts
X All registered keys X Registering Immobilizer Key
failure
X Keys you want to register (registered key or new key) (* 1) X Registering Immobilizer Key
X All registered keys X Registering Immobilizer Key
X X Keys you want to register (registered key or new key) X Registering Immobilizer Key
X X Keys you want to register (registered key or new key) (*1) X Registering Immobilizer Key
X X All registered keys X Registering Immobilizer Key
X X New key you want to register X Registering Immobilizer Key
2 parts
X X New key you want to register X Registering Immobilizer Key
failure
X X New key you want to register X Registering Immobilizer Key
X X Keys you want to register (registered key or new key) (*1) X X Registering Immobilizer Key
X X All registered keys X X Registering Immobilizer Key
X X Keys you want to register (registered key or new key) (*1) X X (*2) Registering Immobilizer Key
X X X Keys you want to register (registered key or new key) (*1) X X Registering Immobilizer Key
11
X X X Keys you want to register (registered key or new key) X X Registering Immobilizer Key
A type
X X X Keys you want to register (registered key or new key) (*1) X X (*2) Registering Immobilizer Key
3 parts
X X X New key you want to register X X Registering Immobilizer Key
failure
X X X New key you want to register X X Registering Immobilizer Key
X X X New key you want to register X X (*2) Registering Immobilizer Key
X X X Keys you want to register (registered key or new key) (*1) X X X (*2) Registering Immobilizer Key
4 parts X X X X Keys you want to register (registered key or new key) (*1) X X X (*2) Registering Immobilizer Key
failure X X X X New key you want to register X X X (*2) Registering Immobilizer Key
*1: When the body integrated unit is replaced, a new key must be used.
The models that require a new key are following:
•LEGACY, OUTBACK (2004MY to 2008MY)
•IMPREZA (2008MY to 2010MY)
•FORESTER (2009MY to 2010MY)
•TRIBECA (From 2006MY)
*2: The registration work cannot be performed in the current state. The security ID must be written. Contact your Subaru service representative.
*3: If you have lost your security ID, please contact your Subaru service representative.
*4: Without security CU
*5: With security CU
REGISTRATION MANUAL FOR IMMOBILIZER
S1001BE.fm 12 ページ 2014年4月30日 水曜日 午後2時9分
Å`
SIE-id::
4-3 Correspondence table when registration is not possible
Vehicle-id:
A list of possible trouble mode, when an error screen is displayed at each status (procedure).
No. Status (procedure) Error screen Trouble mode Action to be taken
Perform the diagnosis for the K line.
(1) Click Normal Diagnosis for the body integrated unit to check if communication with
Select "Immobilizer" from the Main
K line communication failure between Subaru Select Monitor is possible.
Menu
1 NG Comm. Failed Subaru Select Monitor and body integrated (2) Perform communication with a system other than the body integrated unit, and when
→ System "Immobilizer" → Smart
unit communication is possible, check mainly the K line of the body integrated unit connector.
System "NO" → IGN-ON "YES" →
When communication with other systems is not possible as well, replace Subaru Select
Monitor.
Security ID unregistered in either body
Read out the security ID.
Communication error has occurred. integrated unit or combination meter/
Enter the security ID → x "Security Contact your Subaru service representative.
2 security CM
ID is being collated."
NG Security ID is incorrect x 3 times → Read out the security ID.
Incorrect security ID
initial screen Contact your Subaru service representative.
•Subaru Select Monitor failure Check version of Subaru Select Monitor.
NG EGI security access NG
•ECM failure Replace the ECM.
Wait until the self shut completes, and retry the procedure.
When the same error is indicated again, remove and install the battery.
NG EGI-SSM Communication ECM failure
Check the communication line between ECM and Subaru Select Monitor. (K line or CAN
communication line)
Communication failure between ECM and
NG EGI-Immobilizer communication Perform the diagnosis for DTC B1572 (P1572).
body integrated unit
•Communication failure with combination Perform the diagnosis for DTC B1578 (P1578).
→ "Do you want to register the meter/security CM * When a new body integrated unit is installed, DTC B1401 that is checked at step 1 of the
NG Meter/SCU error
3 Engine ECM?" → "Engine ECM •Combination meter/security CM diagnosis above is not detected. In this case, check the LAN communication system, and
Initializing communication..." malfunction when no failure is detected, replace the combination meter or security CM.
12
Wait until the self shut completes, and retry the procedure.
A type
Å`
SIE-id::
No. Status (procedure) Error screen Trouble mode Action to be taken
Vehicle-id:
The message on the left is indicated, when the diagnosis is performed on the remote
control engine starter side, such as inspection for connection with the remote control
→ "Remote control engine start Registration failure with remote control
5 Remote engine start Registration failed engine starter (the message on the left is indicated, when registration is attempted with a
registering..." engine starter
non-genuine remote control engine starter installed), or when the remote control engine
starter unit is malfunctioning.
* When meter failure is detected, registration may not be possible. (This is because meter failure remains even for communication failure or EEPROM failure.)
13
A type
REGISTRATION MANUAL FOR IMMOBILIZER
S1001BE.fm 14 ページ 2014年4月30日 水曜日 午後2時9分
B type
REGISTRATION MANUAL FOR IMMOBILIZER
5 B type C: Caution
Vehicle that does NOT have a keyless access with • When you install wireless radios or car
push button start system, without security ID phones, make sure that the immobilizer
(security tag) when the vehicle is new, and without system is not influenced by their electric
immobilizer CM waves.
• Do not operate cell phones or wireless radios
A: Structure or the like when either trouble diagnosis or
An immobilizer system consists of the following immobilizer registration is in progress.
components: Combination meter or security CU • During immobilizer registration, do not bring
(for a model with security CU), immobilizer
a key with a different ID close to the ignition
indicator (in the combination meter), body
switch. When the key is on a keychain,
integrated unit, ECM, ignition key, and immobilizer
remove it from the chain before start of
antenna.
diagnosis. When there are several keys on
B: Operation one keychain, remove them from the
When the ignition key incorporating a transponder keychain and use them individually for the
is inserted into the key cylinder, the body integrated work.
unit receives the ignition key ID via the immobilizer
• When the engine cannot be started with a
antenna.
registered key, pull the ignition key from the
The received key ID is collated with the key ID
ignition switch, wait approximately one
stored in the memory of the body integrated unit. At
the same time, the meter IDs (SCU IDs) stored in second until the immobilizer warning lamp
the memory of the body integrated unit and starts flashing, and then turn the ignition key
combination meter (or the security CU) are slowly to start the engine.
collated. • Confirm that the battery voltage is 11 V or
Then, the engine IDs stored in the memory of the more and execute each mode.
ECM and body integrated unit are collated. • During immobilizer registration, make sure
If the IDs do not match within the specified period of connectors do not get disconnected.
time after the RPM of the engine reaches the
Note:
specified RPM, the engine stops.
When performing either one of the operations
If the IDs do not match, the engine stops within a
couple of seconds. If the engine does not start as a shown below, perform also the "Registering
result of a mismatch of the IDs, the immobilizer Remote Control Engine Starter".
indicator in the combination meter turns on to • Installing remote control engine starter
indicate that the immobilizer is active. When the • Replacing remote control engine starter
ignition key is removed, the immobilizer is activated • Replacing collation ECM of a vehicle
and the immobilizer indicator lamp flashes to equipped with remote control engine starter
generate an alert notifying people around the
vehicle that it is protected by the immobilizer.
14
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 15 ページ 2014年4月30日 水曜日 午後2時9分
B type
REGISTRATION MANUAL FOR IMMOBILIZER
5-1 Adding Keys 4) Click the [YES] button if the System Check
screen is displayed.
Caution:
To add keys, you need one registered key.
IM-00405
IM-00491
IM-00405
IM-00406
IM-00406
15
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 16 ページ 2014年4月30日 水曜日 午後2時9分
B type
REGISTRATION MANUAL FOR IMMOBILIZER
7) On the Main Menu that appears on the display, 11) Stand by as the key is being collated.
select [Immobilizer system registration]. Note:
Note: When an error screen is displayed, refer to No. 3 in
If the command input screen is displayed instead of "5-8 Correspondence table when registration is not
the menu screen, the vehicle is A type. See the possible".
procedures for A type vehicle. 12) The following screen showing successful key
collation will be displayed. Turn off the ignition
switch, and then replace the key with one to be
registered to turn on the ignition.
IM-00424 Note:
When an error screen is displayed, refer to No. 4 in
"5-8 Correspondence table when registration is not
possible".
IM-00424
IM-00425
IM-00418
16
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 17 ページ 2014年4月30日 水曜日 午後2時9分
B type
REGISTRATION MANUAL FOR IMMOBILIZER
IM-00429
IM-00428
18) Make sure the engine can be started with all the
15) Stand by as the registration is processed. registered keys, then quit the registration
Note: procedure.
When an error screen is displayed, refer to No. 5 in
"5-8 Correspondence table when registration is not
possible".
IM-00418
IM-00418
IM-00431
17
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 18 ページ 2014年4月30日 水曜日 午後2時9分
B type
REGISTRATION MANUAL FOR IMMOBILIZER
5-2 Registering Body Integrated Unit 4) Click the [YES] button if the System Check
screen is displayed.
Caution:
All of the registered keys are required.
1) Start the PC application according to section
"Starting Up the System" and display the Main
Menu screen. Using the registered key, turn on IM-00404
the ignition switch. (Refer to "PC application
help for Subaru Select Monitor".)
Caution:
Make sure to use a registered key.
IM-00404
2) On the Main Menu, select [All other models].
Note:
Audio System is the specification only for the U.K.
5) On the next screen, confirm the system is
keyless access with push button start system.
Click the [NO] button.
IM-00491 IM-00405
3) Select [Immobilizer] from the item selection
dialog box.
IM-00405
IM-00406
IM-00406
18
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 19 ページ 2014年4月30日 水曜日 午後2時9分
B type
REGISTRATION MANUAL FOR IMMOBILIZER
IM-00430
IM-00425
IM-00426 IM-00418
IM-00418
11) Stand by as the key is being read.
19
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 20 ページ 2014年4月30日 水曜日 午後2時9分
B type
REGISTRATION MANUAL FOR IMMOBILIZER
15) The screen shown below will appear if 18) The screen shown below will appear if
registration ends normally. If you have another registration ends normally. Remove the key and
keys to be registered, insert the next key into click the [OK] button.
the ignition switch, turn on the ignition key, and
return to step 14. If you have no more keys to
be registered, click the [Exit] button.
Note: IM-00429
When an error screen is displayed, refer to No. 8
and 9 in "5-8 Correspondence table when
registration is not possible".
19) Make sure the engine can be started with all the
IM-00428 registered keys, then quit the registration
procedure.
IM-00418
IM-00418
20
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 21 ページ 2014年4月30日 水曜日 午後2時9分
B type
REGISTRATION MANUAL FOR IMMOBILIZER
5-3 Registering Engine ECM 5) On the next screen, confirm the system is
keyless access with push button start system.
Caution:
Click the [NO] button.
To add keys, you need one registered key.
1) Start the PC application according to section
"Starting Up the System" and display the Main
Menu screen. Using the registered key, turn on
the ignition switch. (Refer to "PC application IM-00405
help for Subaru Select Monitor".)
Caution:
Make sure to use a registered key.
2) On the Main Menu, select [All other models]. IM-00405
IM-00491
IM-00406
IM-00424
IM-00404
IM-00424
IM-00404
Note:
Audio System is the specification only for the U.K.
21
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 22 ページ 2014年4月30日 水曜日 午後2時9分
B type
REGISTRATION MANUAL FOR IMMOBILIZER
22
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 23 ページ 2014年4月30日 水曜日 午後2時9分
B type
REGISTRATION MANUAL FOR IMMOBILIZER
4) Click the [YES] button if the System Check 7) On the Main Menu that appears on the display,
screen is displayed. select [Meter/SCU registration].
Note:
If the command input screen is displayed instead of
the menu screen, the vehicle is A type. See the
IM-00404 procedures for A type vehicle.
IM-00424
IM-00404
Note:
Audio System is the specification only for the U.K.
5) On the next screen, confirm the system is
IM-00424
keyless access with push button start system.
Click the [NO] button. 8) The registration confirmation dialog box
appears. Click the [OK] button.
9) The ignition confirmation dialog box appears.
Confirm that the ignition switch is ON and then
click the [OK] button.
IM-00405
10) Stand by as the body integrated unit is
initialized.
Note:
When an error screen is displayed, refer to No. 12
IM-00405 in "5-8 Correspondence table when registration is
6) Click [YES] after confirming if the ignition switch not possible".
is ON, as following screen will be displayed.
Note:
When an error screen is displayed, refer to No. 1 in
"5-8 Correspondence table when registration is not IM-00426
possible".
IM-00406
11) If registration ends normally, the screen shows
that registration of the Meter/SCU has been
completed successfully. Click the [OK] button.
12) The screen shows that processes have been
IM-00406 completed. Remove the key and click the [OK]
button.
13) After confirming that the engine can be started
with the registered key, quit the registration
procedure.
23
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 24 ページ 2014年4月30日 水曜日 午後2時9分
B type
REGISTRATION MANUAL FOR IMMOBILIZER
5-5 Registering Remote Control 4) Click the [YES] button if the System Check
Engine Starter screen is displayed.
Caution:
To add keys, you need one registered key.
1) Start the PC application according to section
"Starting Up the System" and display the Main IM-00404
Menu screen. Using the registered key, turn on
the ignition switch. (Refer to "PC application
help for Subaru Select Monitor".)
Caution: IM-00404
Make sure to use a registered key.
2) On the Main Menu, select [All other models]. Note:
Audio System is the specification only for the U.K.
5) On the next screen, confirm the system is
keyless access with push button start system.
Click the [NO] button.
IM-00405
IM-00491
IM-00405
IM-00406
IM-00406
24
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 25 ページ 2014年4月30日 水曜日 午後2時9分
B type
REGISTRATION MANUAL FOR IMMOBILIZER
7) On the Main Menu that appears on the display, 5-6 Deleting Key ID
select [Remote Control Engine Starter
Caution:
Registration].
You can keep one key and delete all the rest of
Note: keys.
If the command input screen is displayed instead of To do this, you need one registered key that is
the menu screen, the vehicle is A type. See the
to be kept.
procedures for A type vehicle.
1) Start the PC application according to section
"Starting Up the System" and display the Main
Menu screen. Using the registered key you
want to keep, turn on the ignition switch. (Refer
IM-00424
to "PC application help for Subaru Select
Monitor".)
Caution:
Make sure to use a registered key.
IM-00424 2) On the Main Menu, select [All other models].
8) The registration confirmation dialog box
appears. Click the [OK] button.
9) The ignition confirmation dialog box appears.
Confirm that the ignition switch is ON and then
click the [OK] button.
10) Stand by as the body integrated unit is
initialized.
Note:
IM-00491
When an error screen is displayed, refer to No. 14
in "5-8 Correspondence table when registration is 3) Select [Immobilizer] from the item selection
not possible". dialog box.
IM-00426
IM-00492
25
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 26 ページ 2014年4月30日 水曜日 午後2時9分
B type
REGISTRATION MANUAL FOR IMMOBILIZER
4) Click the [YES] button if the System Check 7) On the Main Menu that appears on the display,
screen is displayed. select [Immobilizer Key ID deletion].
Note:
If the command input screen is displayed instead of
the menu screen, the vehicle is A type. See the
IM-00404 procedures for A type vehicle.
IM-00424
IM-00404
Note:
Audio System is the specification only for the U.K.
5) On the next screen, confirm the system is
IM-00424
keyless access with push button start system.
Click the [NO] button. 8) The deletion mode confirmation dialog box
appears. Click the [OK] button.
IM-00405
IM-00433
IM-00405
IM-00426
IM-00406
26
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 27 ページ 2014年4月30日 水曜日 午後2時9分
B type
REGISTRATION MANUAL FOR IMMOBILIZER
IM-00434
IM-00435
IM-00436
27
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 28 ページ 2014年4月30日 水曜日 午後2時9分
Å`
SIE-id::
5-7 Immobilizer system: Correspondence table at the time of parts lost or failure
Vehicle-id:
If all the keys are lost, for protection against vehicle theft you must contact your Subaru service representative.
Caution:
When replacing the parts, always use a new one. Used parts cannot be registered.
28
B type
REGISTRATION MANUAL FOR IMMOBILIZER
S1001BE.fm 29 ページ 2014年4月30日 水曜日 午後2時9分
Å`
SIE-id::
2. Parts replacement table
Vehicle-id:
Note:
• When performing each registration, make sure that the ignition switch is ON, and the driver’s door is kept open. If ignition switch is OFF or all doors are closed,
Body integrated unit will enter sleep mode, therefore each registration can not be performed.
• For vehicle with a remote control engine starter, perform "Registering Remote Control Engine Starter" when the BIU is replaced.
29
keys) keys needed)
"Immobilizer system
B type
Å`
SIE-id::
<When two parts are failed or lost>
Vehicle-id:
Parts required to replace or prepared when items
Parts failed/lost Procedures to perform after parts replacement
Destination on the left fail
Key Body Body
inte- Combi- Security inte- Combi- Security
U.K./ nation ECM Key nation ECM (1) (2) (3) (4)
Others Not all All grated meter CU grated meter CU
Canada
unit unit
"Immobilizer Key ID "Immobilizer system
One registered
O X X X "Meter/SCU registration" deletion" (Deleting lost registration" (Registering
key
keys) keys needed)
"Immobilizer Key ID "Immobilizer system
One registered
O X X X "Engine ECU registration" deletion" (Deleting lost registration" (Registering
key
keys) keys needed)
"Immobilizer system
O X X All registered keys X X
registration"
One registered
O X X X X "Meter/SCU registration" "Engine ECU registration"
key
"Immobilizer Key ID "Immobilizer system
One registered
O X X X "Meter/SCU registration" deletion" (Deleting lost registration" (Registering
key
keys) keys needed)
"Immobilizer Key ID "Immobilizer system
One registered
O X X X "Engine ECU registration" deletion" (Deleting lost registration" (Registering
key
keys) keys needed)
"Immobilizer system
O X X All registered keys X X
registration"
One registered
O X X X X "Meter/SCU registration" "Engine ECU registration"
key
30
<When three parts are failed or lost>
B type
Å`
SIE-id::
5-8 Correspondence table when registration is not possible
Vehicle-id:
A list of possible trouble mode, when an error screen is displayed at each status (procedure).
Note:
TYPE B-1: Model other than TYPE B-2
TYPE B-2: From 2015MY LEGACY / OUTBACK
No. Status (procedure) Screen Trouble mode Action to be taken
Select "Immobilizer" from the Main NG Comm. Failed CAN communication failure between Subaru Select Monitor and body
Perform the diagnosis for LAN system.
Menu integrated unit
1
→ System "Immobilizer" → Smart CAN communication failure between Subaru Select Monitor and body
System "NO" → IGN-ON "YES" → Command input screen Perform the diagnosis for LAN system.
integrated unit (Only when K line communication is used for ECM)
Wait approximately one minute, and retry the procedure.
When the same error is indicated again, remove the Subaru Select
Body integrated unit erroneous operation (possibility that last Monitor once. Wait approximately one minute, and retry the
registration mode still not canceled) procedure.
NG BIU-SSM Communication When the same error is indicated again, remove and install the
battery.
Key IN, IGN-ON not completed [Only when the error screen on the left Wait approximately one minute, perform key IN, IGN-ON, and retry the
is indicated after five seconds or more elapsed] procedure.
•Subaru Select Monitor failure Check version of Subaru Select Monitor.
NG BIU security access NG
•Body integrated unit failure Replace the body integrated unit.
"Immobilizer system registration" NG Number of registrations
Number of registrations exceeded —
start exceeded
2
→ "BIU Initializing Execute "Meter/SCU registration" to register the combination meter/
communication..." display Meter/SCU not registration Combination meter/security CM unregistered
security CM.
31
[Body integrated unit unregistered] DTC is detected except for a new unit of TYPE B-1. Therefore, check
•Communication failure between combination meter/security CM and DTC and perform the diagnosis.
B type
Å`
SIE-id::
No. Status (procedure) Screen Trouble mode Action to be taken
Vehicle-id:
Check DTC and perform the diagnosis.
NG Antenna Immobilizer antenna failure
(When this screen is displayed, DTC B1411 is stored.)
Check DTC and perform the diagnosis.
NG Key Communication Failure Transponder failure
(When this screen is displayed, DTC B1410 is stored.)
NG IMM Control Module EEPROM Body integrated unit failure Perform the diagnosis for DTC B1577 (P1577).
5 → "Key has been registered" NG Performed conditions not
With four keys registered, IGN-OFF → ON —
established.
Check DTC and perform the diagnosis.
NG Meter/SCU error Combination meter/security CM malfunction
(When this screen is displayed, B1408/B1406 is stored.)
Check DTC and perform the diagnosis.
NG Meter/SCU Communication Communication failure with combination meter/security CM
(When this screen is displayed, B1407/B1409 is stored.)
NG Performed conditions not
Time-out before the key is replaced (60 seconds) —
established.
DTC is detected for TYPE B-2. Therefore, check DTC and perform the
diagnosis. (When this screen is displayed, DTC B1411 is stored.)
NG Antenna Immobilizer antenna failure
DTC is not detected for TYPE B-1. Therefore, perform the diagnosis
(Body integrated unit replacement for DTC B1411.
mode) DTC is detected for TYPE B-2. Therefore, check DTC and perform the
6
→ "Confirm you replace all the diagnosis. (When this screen is displayed, DTC B1410 is stored.)
keys..." DTC is not detected for TYPE B-1. Therefore, perform the diagnosis
NG Key - Communication Failure Transponder failure as follows:
1) Retry the procedure using a different key.
2) Replace the immobilizer antenna, and retry the procedure.
3) Replace the body integrated unit.
NG Use of Unregistered Key NG key (at least one key) Prepare the registered key.
NG Performed conditions not
With collation status OK, the key was not replaced —
established.
32
DTC is detected for TYPE B-2. Therefore, check DTC and perform the
diagnosis. (When this screen is displayed, DTC B1411 is stored.)
B type
Å`
SIE-id::
No. Status (procedure) Screen Trouble mode Action to be taken
Vehicle-id:
Check DTC and perform the diagnosis.
NG Antenna Immobilizer antenna failure
(When this screen is displayed, DTC B1411 is stored.)
Check DTC and perform the diagnosis.
NG Key - Communication Failure Transponder failure
(When this screen is displayed, DTC B1410 is stored.)
NG IMM Control Module EEPROM Body integrated unit failure Perform the diagnosis for DTC B1577 (P1577).
NG Performed conditions not
With four keys registered, IGN-OFF → ON —
established.
DTC is detected for TYPE B-2. Therefore, check DTC and perform the
diagnosis. (When this screen is displayed, DTC B1408/B1406 is
stored.)
DTC is not detected for TYPE B-1. Therefore, perform the diagnosis
NG Meter/SCU error Combination meter/security CM malfunction
as follows:
8 → "Key has been registered"
1) Clear the memory, and retry the procedure.
2) When the same error is indicated again even after retrying the
procedure, replace the combination meter/security CM.
DTC is detected for TYPE B-2. Therefore, check DTC and perform the
diagnosis. (When this screen is displayed, DTC B1407/B1409 is
stored.)
DTC is not detected for TYPE B-1. Therefore, perform the diagnosis
as follows:
NG Meter/SCU Communication Communication failure with combination meter/security CM
1) Inspect the communication line between combination meter/
security CM and body integrated unit.
2) When the same error is indicated again even after the inspection
and retrying the procedure, replace the combination meter/security
CM.
NG EGI-SSM Communication Check the communication line between ECM and Subaru Select
Communication failure with ECM
(Communication line judgment) Monitor. (K line or CAN communication line)
NG EGI-Immobilizer communication Communication failure between ECM and body integrated unit Perform the diagnosis for DTC B1572 (P1572).
NG IMM Control Module EEPROM Body integrated unit failure Perform the diagnosis for DTC B1577 (P1577).
33
Wait until the self shut completes, and retry the procedure.
B type
NG EGI unit EEPROM ECM failure When the same error is indicated again, remove and install the
→ "EGI initialization / During battery.
9
registration..."
Check version of Subaru Select Monitor.
NG EGI security access NG Subaru Select Monitor failure
Replace the ECM.
Wait until the self shut completes, and retry the procedure.
When the same error is indicated again, remove and install the
NG EGI-SSM Communication ECM failure battery.
Check the communication line between ECM and Subaru Select
Monitor. (K line or CAN communication line)
REGISTRATION MANUAL FOR IMMOBILIZER
S1001BE.fm 34 ページ 2014年4月30日 水曜日 午後2時9分
Å`
SIE-id::
No. Status (procedure) Screen Trouble mode Action to be taken
Vehicle-id:
Wait approximately one minute, and retry the procedure.
•Body integrated unit erroneous operation (possibility that last When the same error is indicated again, remove the Subaru Select
registration mode still not canceled) Monitor once. Wait approximately one minute, and retry the
NG BIU-SSM Communication
•Key IN, IGN-ON not completed [Only when the error screen on the procedure.
left is indicated after ten seconds or more elapsed] When the same error is indicated again, remove and install the
battery.
Check version of Subaru Select Monitor.
NG BIU security access NG Subaru Select Monitor failure
Replace the body integrated unit.
Check DTC and perform the diagnosis.
NG Antenna Immobilizer antenna failure
(When this screen is displayed, DTC B1411 is stored.)
Check DTC and perform the diagnosis.
NG Key - Communication Failure Transponder failure
(When this screen is displayed, DTC B1410 is stored.)
"Engine ECU registration" start
10 → "BIU Initializing NG Key-Immob comm/ Immob unit Check DTC and perform the diagnosis.
Transponder failure and body integrated unit failure
communication..." display EEPROM (When this screen is displayed, DTC B1410 is stored.)
•NG key Prepare the registered key.
NG Use of Unregistered Key •Unregistered key Execute "Immobilizer system registration" to register the key to the
•Body integrated unit unregistered body integrated unit.
NG IMM Control Module EEPROM Body integrated unit failure Perform the diagnosis for DTC B1577 (P1577).
•Communication failure with combination meter/security CM Check DTC and perform the diagnosis.
NG Meter/SCU error (When this screen is displayed, DTC B1408/B1406 or B1407/B1409 is
•Combination meter/security CM malfunction stored.)
Check DTC and perform the diagnosis.
NG Meters / SCU checking NG Combination meter/security CM not genuine part
(When this screen is displayed, DTC B1401/B1405 is stored.)
NG Performed conditions not Execute "Meter/SCU registration" to register the combination meter/
Combination meter/security CM unregistered
established. security CM.
NG EGI-SSM Communication Check the communication line between ECM and Subaru Select
Communication failure with ECM
(Communication line judgment) Monitor. (K line or CAN communication line)
34
NG EGI-Immobilizer communication Communication failure between ECM and body integrated unit Perform the diagnosis for DTC B1572 (P1572).
B type
NG IMM Control Module EEPROM Body integrated unit failure Perform the diagnosis for DTC B1577 (P1577).
Wait until the self shut completes, and retry the procedure.
NG EGI unit EEPROM ECM failure When the same error is indicated again, remove and install the
→ "EGI initialization / During battery.
11
registration..."
Check version of Subaru Select Monitor.
NG EGI security access NG Subaru Select Monitor failure
Replace the ECM.
Wait until the self shut completes, and retry the procedure.
When the same error is indicated again, remove and install the
NG EGI-SSM Communication ECM failure battery.
Check the communication line between ECM and Subaru Select
Monitor. (K line or CAN communication line)
REGISTRATION MANUAL FOR IMMOBILIZER
S1001BE.fm 35 ページ 2014年4月30日 水曜日 午後2時9分
Å`
SIE-id::
No. Status (procedure) Screen Trouble mode Action to be taken
Vehicle-id:
Wait approximately one minute, and retry the procedure.
•Body integrated unit erroneous operation (possibility that last When the same error is indicated again, remove the Subaru Select
registration mode still not canceled) Monitor once. Wait approximately one minute, and retry the
NG BIU-SSM Communication
•Key IN, IGN-ON not completed [Only when the error screen on the procedure.
left is indicated after ten seconds or more elapsed] When the same error is indicated again, remove and install the
battery.
Check version of Subaru Select Monitor.
NG BIU security access NG Subaru Select Monitor failure
Replace the body integrated unit.
Check DTC and perform the diagnosis.
NG Antenna Immobilizer antenna failure
(When this screen is displayed, DTC B1411 is stored.)
Check DTC and perform the diagnosis.
NG Key - Communication Failure Transponder failure
(When this screen is displayed, DTC B1410 is stored.)
NG Key-Immob comm/ Immob unit Check DTC and perform the diagnosis.
"Meter/SCU registration" start Transponder failure and body integrated unit failure
EEPROM (When this screen is displayed, DTC B1410 is stored.)
12 → "BIU Initializing
communication..." display •NG key Prepare the registered key.
NG Use of Unregistered Key •Unregistered key Execute "Immobilizer system registration" to register the key to body
•Body integrated unit unregistered integrated unit.
NG IMM Control Module EEPROM Body integrated unit failure Perform the diagnosis for DTC B1577 (P1577).
•Communication failure with combination meter/security CM Check DTC and perform the diagnosis.
NG Meter/SCU error (When this screen is displayed, DTC B1408/B1406 or B1407/B1409 is
•Combination meter/security CM malfunction stored.)
•Combination meter/security CM not genuine part Check DTC and perform the diagnosis.
NG Meters / SCU checking NG
•Combination meter/security CM registered on another vehicle (When this screen is displayed, DTC B1401/B1405 is stored.)
NG Performed conditions not
Combination meter/security CM registered —
established.
Check DTC and perform the diagnosis.
NG Meter/SCU Communication Communication failure with combination meter/security CM
(When this screen is displayed, DTC B1407/B1409 is stored.)
35
Wait approximately one minute, and retry the procedure.
•Body integrated unit erroneous operation (possibility that last
B type
When the same error is indicated again, remove the Subaru Select
registration mode still not canceled) Monitor once. Wait approximately one minute, and retry the
NG BIU-SSM Communication
•Key IN, IGN-ON not completed [Only when the error screen on the procedure.
left is indicated after ten seconds or more elapsed] When the same error is indicated again, remove and install the
battery.
Check version of Subaru Select Monitor.
NG BIU security access NG Subaru Select Monitor failure
Replace the body integrated unit.
Check DTC and perform the diagnosis.
NG Antenna Immobilizer antenna failure
(When this screen is displayed, DTC B1411 is stored.)
Check DTC and perform the diagnosis.
NG Key - Communication Failure Transponder failure
(When this screen is displayed, DTC B1410 is stored.)
"Immobilizer key ID deletion" start
NG Key-Immob comm/ Immob unit Check DTC and perform the diagnosis.
13 → "BIU Initializing Transponder failure and body integrated unit failure
EEPROM (When this screen is displayed, DTC B1410 is stored.)
communication..." display
•NG key Prepare the registered key.
NG Use of Unregistered Key •Unregistered key Execute "Immobilizer system registration" to register the key to body
•Body integrated unit unregistered integrated unit.
NG IMM Control Module EEPROM Body integrated unit failure Perform the diagnosis for DTC B1577 (P1577).
•Communication failure with combination meter/security CM Check DTC and perform the diagnosis.
NG Meter/SCU error (When this screen is displayed, DTC B1408/B1406 or B1407/B1409 is
•Combination meter/security CM malfunction stored.)
Check DTC and perform the diagnosis.
NG Meters / SCU checking NG Combination meter/security CM not genuine part
(When this screen is displayed, DTC B1401/B1405 is stored.)
NG Performed conditions not Execute "Meter/SCM registration" to register the combination meter/
Combination meter/security CM unregistered
established. security CM.
REGISTRATION MANUAL FOR IMMOBILIZER
S1001BE.fm 36 ページ 2014年4月30日 水曜日 午後2時9分
Å`
SIE-id::
No. Status (procedure) Screen Trouble mode Action to be taken
Vehicle-id:
Wait approximately one minute, and retry the procedure.
•Body integrated unit erroneous operation (possibility that last When the same error is indicated again, remove the Subaru Select
registration mode still not canceled) Monitor once. Wait approximately one minute, and retry the
NG BIU-SSM Communication
•Key IN, IGN-ON not completed [Only when the error screen on the procedure.
left is indicated after ten seconds or more elapsed] When the same error is indicated again, remove and install the
battery.
Check version of Subaru Select Monitor.
NG BIU security access NG Subaru Select Monitor failure
Replace the body integrated unit.
Check DTC and perform the diagnosis.
NG Antenna Immobilizer antenna failure
(When this screen is displayed, DTC B1411 is stored.)
Check DTC and perform the diagnosis.
NG Key - Communication Failure Transponder failure
(When this screen is displayed, DTC B1410 is stored.)
NG Key-Immob comm/ Immob unit Check DTC and perform the diagnosis.
Transponder failure and body integrated unit failure
EEPROM (When this screen is displayed, DTC B1410 is stored.)
"Remote Control Engine Starter •NG key Prepare the registered key.
Registration" start
14 NG Use of Unregistered Key •Unregistered key Execute "Immobilizer system registration" to register the key to body
→ "BIU Initializing
•Body integrated unit unregistered integrated unit.
communication..." display
NG IMM Control Module EEPROM Body integrated unit failure Perform the diagnosis for DTC B1577 (P1577).
Check DTC and perform the diagnosis.
NG Meter/SCU error Combination meter/security CM malfunction (When this screen is displayed, DTC B1408/B1406 or B1407/B1409 is
stored.)
Check DTC and perform the diagnosis.
NG Meters / SCU checking NG Combination meter/security CM not genuine part
(When this screen is displayed, DTC B1401/B1405 is stored.)
NG Performed conditions not Execute "Meter/SCU registration" to register the combination meter/
Combination meter/security CM unregistered
established. security CM.
The message on the left is indicated, when the diagnosis is performed
on the remote control engine starter side, such as inspection for
36
connection with the remote control engine starter (the message on the
NG Remote start registration NG Registration failure with remote control engine starter
left is indicated, when registration is attempted with a non-genuine
B type
C type
REGISTRATION MANUAL FOR IMMOBILIZER
6 C type C: Caution
Vehicle that has a keyless access with push button • The security ID and registration command
start system and is originally provided with a must be handled as confidential information
security ID (security tag) and shall not be announced to outsiders.
• When you install wireless radios or car
phones, make sure that the immobilizer
A: Structure system is not influenced by their electric
An immobilizer system consists of the following waves.
components: Combination meter, immobilizer • Do not operate cell phones or wireless radios
or the like when either trouble diagnosis or
indicator (in the combination meter), access key,
immobilizer registration is in progress.
immobilizer antenna (incorporating a push switch),
• During immobilizer registration, do not bring a
collation CM, power supply CM, gateway CM, key with a different ID close to the ignition
steering lock CM, ID code box, indoor and outdoor switch. When the access key is on a keychain,
antennas, receiver, body integrated unit, and remove it from the chain before the start of
engine ECM. diagnosis. When there are several keys on one
keychain, remove them from the keychain and
B: Operation use them individually for the work.
Get in the vehicle with your access key and let the • The work of "Registering the Smart
access key send the ID via the indoor antenna. The Immobilizer", "Registering the Smart ECM"
access key sends the ID to the receiver and the and "Delete the Mobile Key (Access Key) ID"
includes the operation of holding up the
received ID is sent to the collation CM where it is access key to the push engine switch (push-
collated with the IDs of other immobilizer-related button ignition switch). Pay attention to the
units. Step on the brake pedal (for an AT model) or following when performing this operation.
clutch pedal (for a MT model) and press the push • Confirm that the battery voltage is 11 V or
engine switch so that the starter rotates to start the more and execute each mode.
engine. • When confirm/register access key, only one
key can be brought into vehicle at a time.
If the IDs do not match within the specified period of For registration of multiple keys, bring a key
time after the RPM of the engine reaches the into vehicle and perform registration while
specified RPM, the engine stops. If the IDs do not leaving rest of other keys outside.
match, the engine stops within a couple of • When holding up the access key to the
seconds. If the engine does not start as a result of push engine switch (push-button ignition
a mismatch of the IDs, the immobilizer indicator switch), do not hold two or more access
keys at the same time, but use only one
lamp in the combination meter turns on to indicate each time. (When the access key is on a
that the immobilizer is active. When the immobilizer keychain, remove it from the keychain
is activated, the immobilizer indicator lamp flashes before the work.)
to generate an alert notifying people around the • When holding the access key up to the
vehicle that it is protected by the immobilizer. push engine switch (push-button ignition
switch), bring the access key close to the
push engine switch (push-button ignition
switch) as shown below.
SL-00717
37
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 38 ページ 2014年4月30日 水曜日 午後2時9分
C type
REGISTRATION MANUAL FOR IMMOBILIZER
38
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 39 ページ 2014年4月30日 水曜日 午後2時9分
C type
REGISTRATION MANUAL FOR IMMOBILIZER
6-1 Adding Access Keys 5) On the next screen, confirm the system is
keyless access with push button start system.
Note:
Click the [YES] button.
Depending on the replacement part, a different
screen from the screen shown in this item may be
displayed. In such a case, follow the instructions
shown on the screens.
1) Start the PC application according to section
"Starting Up the System" and display the Main
Menu screen. (Refer to "PC application help for
Subaru Select Monitor".)
2) On the Main Menu, select [All other models].
IM-00437
Note:
The term [smart system] that appears on this
screen is synonymous with the term [keyless
access with push button start system] used in this
text.
6) Input the teaching operation code, and then
click the [OK] button.
IM-00491 Note:
3) Select [Immobilizer] from the item selection If the menu screen is displayed instead of the
dialog box. command input screen, the vehicle is D type. See
the procedures for D type vehicle.
IM-00492
IM-00408
4) Click the [YES] button if the System Check
screen is displayed. Note:
When you wish to return to the Main Menu screen,
click the [QUIT] button.
IM-00404
Note:
Audio System is the specification only for the U.K.
39
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 40 ページ 2014年4月30日 水曜日 午後2時9分
C type
REGISTRATION MANUAL FOR IMMOBILIZER
7) The registration mode selection dialog box 11) Wait until the smart immobilizer is then being
appears. Click the [Smart Immobilizer registered.
Registration] button.
IM-00439
IM-00438
12) The dialog box to confirm already registered
8) On the registration mode confirmation dialog access keys appears. Hold one of those access
box that appears, click the [OK] button. keys over the push engine switch (push-button
ignition switch). After the buzzer sounds once,
move the access key away from the push
engine switch (push-button ignition switch) and
go to the next step.
IM-00477
IM-00440
Note:
• When holding the access key up to the push
engine switch (push-button ignition switch), bring
the access key close to the push engine switch
(push-button ignition switch) as shown below.
IM-00410
SL-00717
40
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 41 ページ 2014年4月30日 水曜日 午後2時9分
C type
REGISTRATION MANUAL FOR IMMOBILIZER
(2) Hold the Subaru ornament side to the push 14) Stand by as the access key is registered.
engine switch (push-button ignition switch)
side.
(3) Bring it close until it touches the push
engine switch (push-button ignition switch).
• The procedure to hold an access key over the
push engine switch (push-button ignition switch)
has to be done within 30 seconds after the
screen above appears.
13) When screen displays access key registration IM-00439
mode shown below, hold one access key you 15) Once the registration ends normally, the
wish to register additionally over the push [Registered number] increases by one as you
engine switch (push-button ignition switch). can see on the screen below. If you have
another access key to be registered, repeat
steps 13 through 14. If you do not have any
more keys to be registered, click the [Quit]
button and move on to step 16.
IM-00441
Note:
• When the buzzer has sounded twice, the work of
holding the access key up has been completed,
but for 10 seconds after the work, the access key IM-00442
should be kept inside the vehicle (near the select 16) Once following screen appears, turn the push
lever). engine switch (push-button ignition switch) off.
• For registration of the next access key, the Then open or close the driver’s door, depending
previously registered access key should be on its status.
removed from the vehicle.
• Do not click the [Quit] button until you finish
registering all the access keys you wish to
register.
• The procedure to hold an access key over the
push engine switch (push-button ignition switch)
has to be done within 30 seconds after the
screen above appears.
IM-00443
41
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 42 ページ 2014年4月30日 水曜日 午後2時9分
C type
REGISTRATION MANUAL FOR IMMOBILIZER
17) Then following screen appears. Turn the 6-2 Registering Collation CU
ignition on.
Caution:
A registered access key is required. If
registration completed before registering a
desired access key, such an unregistered
access key cannot be used anymore. When
necessary, prepare a new access key, and
perform additional registration.
Note:
Depending on the replacement part, a different
IM-00444
screen from the screen shown in this item may be
18) Stand by as the registration to the ECM is being displayed. In such a case, follow the instructions
completed. shown on the screens.
1) Start the PC application according to section
"Starting Up the System" and display the Main
Menu screen. (Refer to "PC application help for
Subaru Select Monitor".)
2) On the Main Menu, select [All other models].
IM-00445
IM-00491
IM-00446
42
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 43 ページ 2014年4月30日 水曜日 午後2時9分
C type
REGISTRATION MANUAL FOR IMMOBILIZER
4) Click the [YES] button if the System Check 6) Input the teaching operation code, and then
screen is displayed. click the [OK] button.
Note:
If the menu screen is displayed instead of the
command input screen, the vehicle is D type. See
the procedures for D type vehicle.
IM-00404
Note:
Audio System is the specification only for the U.K.
5) On the next screen, confirm the system is
IM-00408
keyless access with push button start system.
Click the [YES] button. Note:
When you wish to return to the Main Menu screen,
click the [QUIT] button.
7) The registration mode selection dialog box
appears. Click the [Smart Immobilizer
Registration] button.
IM-00437
Note:
The term [smart system] that appears on this
screen is synonymous with the term [keyless
access with push button start system] used in this
IM-00438
text.
8) On the registration mode confirmation dialog
box that appears, click the [OK] button.
IM-00477
43
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 44 ページ 2014年4月30日 水曜日 午後2時9分
C type
REGISTRATION MANUAL FOR IMMOBILIZER
9) Input the security ID and then click the [OK] 11) When the access key confirmation screen
button. appears, hold up the access key that was
registered to the new collation CM to the push
engine switch (push-button ignition switch).
After the buzzer has sounded once, move the
access key away from the push engine switch
(push-button ignition switch).
Note:
• When holding the access key up to the push
engine switch (push-button ignition switch), bring
IM-00410 the access key close to the push engine switch
10) Stand by as the security ID is being collated. (push-button ignition switch) as shown below.
SL-00717
IM-00411
44
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 45 ページ 2014年4月30日 水曜日 午後2時9分
C type
REGISTRATION MANUAL FOR IMMOBILIZER
13) When screen displays access key registration 15) Once the registration ends normally, the
mode shown below, hold one access key you [Registered number] increases by one as you
wish to register additionally over the push can see on the screen below. If you have
engine switch (push-button ignition switch). another access key to be registered, repeat
steps 13 through 14. If you do not have any
more keys to be registered, click the [Quit]
button and move on to step 16.
IM-00483
Note:
• When the buzzer has sounded twice, the work of
IM-00486
holding the access key up has been completed,
but for 10 seconds after the work, the access key 16) Once following screen appears, turn the push
should be kept inside the vehicle (near the select engine switch (push-button ignition switch) off.
lever). Then open or close the driver’s door, depending
• For registration of the next access key, the on its status.
previously registered access key should be
removed from the vehicle.
• Do not click the [Quit] button until you finish
registering all the access keys you wish to
register.
• The procedure to hold an access key over the
push engine switch (push-button ignition switch)
has to be done within 30 seconds after the
screen above appears. IM-00443
14) Stand by as the access key is registered. 17) Then following screen appears. Turn the
ignition on.
IM-00439
IM-00444
45
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 46 ページ 2014年4月30日 水曜日 午後2時9分
C type
REGISTRATION MANUAL FOR IMMOBILIZER
18) Stand by as the registration to the ECM is being 6-3 Registering the Steering Lock CU
completed. or ID Code Box
1) Start the PC application according to section
"Starting Up the System" and display the Main
Menu screen. (Refer to "PC application help for
Subaru Select Monitor".)
2) On the Main Menu, select [All other models].
IM-00445
IM-00491
IM-00446
IM-00404
Note:
Audio System is the specification only for the U.K.
46
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 47 ページ 2014年4月30日 水曜日 午後2時9分
C type
REGISTRATION MANUAL FOR IMMOBILIZER
5) On the next screen, confirm the system is 8) On the registration mode confirmation dialog
keyless access with push button start system. box that appears, click the [OK] button.
Click the [YES] button.
IM-00448
IM-00437
9) Input the security ID and then click the [OK]
Note: button.
The term [smart system] that appears on this
screen is synonymous with the term [keyless
access with push button start system] used in this
text.
6) Input the teaching operation code, and then
click the [OK] button.
Note:
If the menu screen is displayed instead of the
command input screen, the vehicle is D type. See
the procedures for D type vehicle. IM-00410
IM-00408
Note: IM-00411
When you wish to return to the Main Menu screen, 11) Wait until the smart ECM is then being
click the [QUIT] button.
registered.
7) The registration mode selection dialog box
appears. Click the [Smart ECM Registration]
button.
IM-00449
IM-00447
47
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 48 ページ 2014年4月30日 水曜日 午後2時9分
C type
REGISTRATION MANUAL FOR IMMOBILIZER
12) The dialog box to confirm already registered 13) Smart ECM registration is then automatically
access keys appears. Hold one of those access executed. When the registration ends normally,
keys over the push engine switch (push-button the following screen appears. Click the [OK]
ignition switch). After the buzzer sounds once, button.
move the access key away from the push
engine switch (push-button ignition switch) and
go to the next step.
IM-00451
SL-00717
48
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 49 ページ 2014年4月30日 水曜日 午後2時9分
C type
REGISTRATION MANUAL FOR IMMOBILIZER
6-4 Registering the Engine ECM 5) On the next screen, confirm the system is
keyless access with push button start system.
1) Start the PC application according to section
Click the [YES] button.
"Starting Up the System" and display the Main
Menu screen. (Refer to "PC application help for
Subaru Select Monitor".)
2) On the Main Menu, select [All other models].
IM-00437
Note:
The term [smart system] that appears on this screen
IM-00491
is synonymous with the term [keyless access with
push button start system] used in this text.
3) Select [Immobilizer] from the item selection 6) Input the teaching operation code, and then
dialog box. click the [OK] button.
Note:
If the menu screen is displayed instead of the
command input screen, the vehicle is D type. See
the procedures for D type vehicle.
IM-00492
IM-00408
Note:
When you wish to return to the Main Menu screen,
click the [QUIT] button.
7) The registration mode selection dialog box
appears. Click the [Engine ECM Registration]
button.
IM-00404
Note:
Audio System is the specification only for the U.K.
IM-00452
49
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 50 ページ 2014年4月30日 水曜日 午後2時9分
C type
REGISTRATION MANUAL FOR IMMOBILIZER
8) On the registration mode confirmation dialog 12) The screen shown below will appear if
box that appears, click the [OK] button. registration ends normally. Click the [OK]
button.
IM-00453
IM-00446
9) Input the security ID and then click the [OK]
button. 13) After the screen shown below appears, wait
until the Main Menu screen shows up again.
IM-00410
IM-00454
10) Stand by as the security ID is being collated.
14) After confirming that the keyless access with
push button start system operates normally,
quit the registration operation.
IM-00411
IM-00445
50
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 51 ページ 2014年4月30日 水曜日 午後2時9分
C type
REGISTRATION MANUAL FOR IMMOBILIZER
6-5 Readout the Number of Access 5) On the next screen, confirm the system is
Key Registration keyless access with push button start system.
1) Start the PC application according to section Click the [YES] button.
"Starting Up the System" and display the Main
Menu screen. (Refer to "PC application help for
Subaru Select Monitor".)
2) On the Main Menu, select [All other models].
IM-00437
Note:
The term [smart system] that appears on this
screen is synonymous with the term [keyless
IM-00491 access with push button start system] used in this
3) Select [Immobilizer] from the item selection text.
dialog box. 6) Input the teaching operation code, and then
click the [OK] button.
Note:
If the menu screen is displayed instead of the
command input screen, the vehicle is D type. See
the procedures for D type vehicle.
IM-00492
IM-00408
Note:
When you wish to return to the Main Menu screen,
click the [QUIT] button.
IM-00404
Note:
Audio System is the specification only for the U.K.
51
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 52 ページ 2014年4月30日 水曜日 午後2時9分
C type
REGISTRATION MANUAL FOR IMMOBILIZER
7) The registration mode selection dialog box 6-6 Delete the Access Key ID
appears. Click the [Readout the number of
1) Start the PC application according to section
mobile key registration] button.
"Starting Up the System" and display the Main
Menu screen. (Refer to "PC application help for
Subaru Select Monitor".)
2) On the Main Menu, select [All other models].
IM-00455
IM-00456
IM-00457
IM-00404
Note:
Audio System is the specification only for the U.K.
52
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 53 ページ 2014年4月30日 水曜日 午後2時9分
C type
REGISTRATION MANUAL FOR IMMOBILIZER
5) On the next screen, confirm the system is 8) The confirmation dialog box to carry out the
keyless access with push button start system. access key ID deletion mode appears. Click the
Click the [YES] button. [OK] button.
IM-00437
IM-00459
IM-00408
Note:
When you wish to return to the Main Menu screen, IM-00411
click the [QUIT] button.
7) The registration mode selection dialog box 11) Please wait for deleting registered access key
appears. Click the [Delete the mobile key ID] ID.
button.
IM-00460
IM-00458
53
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 54 ページ 2014年4月30日 水曜日 午後2時9分
C type
REGISTRATION MANUAL FOR IMMOBILIZER
12) As the number of access keys confirmation 13) The screen shown below will appear if access
screen will be displayed, place one of the key ID deletion ends normally. Click the [OK]
access keys, the key, which you do not want to button.
delete the ID, over the push engine switch
(push-button ignition switch). After the buzzer
sounds once, move the access key away from
the push engine switch (push-button ignition
switch) and go to the next step.
IM-00462
Note:
• The ID of an access key placed over the push
engine switch (push-button ignition switch) will
not be deleted.
• When holding the access key up to the push
engine switch (push-button ignition switch), bring
the access key close to the push engine switch
(push-button ignition switch) as shown below.
SL-00717
54
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 55 ページ 2014年4月30日 水曜日 午後2時9分
C type
REGISTRATION MANUAL FOR IMMOBILIZER
6-7 Registering Remote Control 5) On the next screen, confirm the system is
Engine Starter keyless access with push button start system.
1) Start the PC application according to section Click the [YES] button.
"Starting Up the System" and display the Main
Menu screen. (Refer to "PC application help for
Subaru Select Monitor".)
2) On the Main Menu, select [All other models].
IM-00437
Note:
The term [smart system] that appears on this
screen is synonymous with the term [keyless
IM-00491 access with push button start system] used in this
3) Select [Immobilizer] from the item selection text.
dialog box. 6) Input the teaching operation code, and then
click the [OK] button.
Note:
If the menu screen is displayed instead of the
command input screen, the vehicle is D type. See
the procedures for D type vehicle.
IM-00492
IM-00408
Note:
When you wish to return to the Main Menu screen,
click the [QUIT] button.
IM-00404
Note:
Audio System is the specification only for the U.K.
55
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 56 ページ 2014年4月30日 水曜日 午後2時9分
C type
REGISTRATION MANUAL FOR IMMOBILIZER
7) The registration mode selection dialog box 11) Wait until the remote control engine starter is
appears. Click the [Remote Control Engine then being registered.
Starter Registration] button.
IM-00465
IM-00463
12) The screen shown below will appear if remote
8) On the registration mode confirmation dialog control engine starter registration ends
box that appears, click the [OK] button. normally. Click the [OK] button.
IM-00464 IM-00466
9) Input the security ID and then click the [OK] 13) After confirming that the keyless access with
button. push button start system and remote control
engine starter operate normally, quit the
registration operation.
IM-00410
IM-00411
56
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 57 ページ 2014年4月30日 水曜日 午後2時9分
C type
REGISTRATION MANUAL FOR IMMOBILIZER
57
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 58 ページ 2014年4月30日 水曜日 午後2時9分
Å`
SIE-id::
6-9 Keyless access with push button start system (except for North America): Correspondence table at
Vehicle-id:
the time of parts failure
If all the keys are lost, for protection against vehicle theft you must contact your Subaru service representative.
Caution:
Parts to be replaced always shall be replaced by new parts, never by used parts.
* Smart immobilizer registration also includes steering lock initialization work and engine ECM registration.
58
C type
REGISTRATION MANUAL FOR IMMOBILIZER
S1001BE.fm 59 ページ 2014年4月30日 水曜日 午後2時9分
Å`
SIE-id::
2. Parts replacement table
Vehicle-id:
Note:
• When performing each registration, make sure that the ignition switch is turned ON and driver's door is kept open. If ignition switch is OFF or all doors are closed,
Body integrated unit will enter sleep mode, therefore each registration can not be performed.
• After replacing Collation CM without performing [Registering the Smart Immobilizer], if ignition switch is turned ON/OFF for 10 times, it will be impossible to turn ignition switch
ON again. In this case, open driver's door and perform [Registering the Smart Immobilizer]. (In this case, it will possible to perform [Registering the Smart Immobilizer] even
when ignition switch is OFF.)
Note:
• O: Part that failed/was lost
• X: Replace part with new one
59
Execution of smart
C type
All registered
O X immobilizer regis- (*2)
access keys
tration
Steering lock ini-
One registered Execution of smart
O X tialization work
access key ECM registration
(*1)
Execution of
One registered Execution of smart
O X (*4) engine ECM regis-
access key ECM registration
tration
Execution of
O X engine ECM regis-
tration
Execution of smart
One registered
O X immobilizer regis-
access key
tration
Execution of smart
One registered
O X immobilizer regis-
access key
tration
REGISTRATION MANUAL FOR IMMOBILIZER
S1001BE.fm 60 ページ 2014年4月30日 水曜日 午後2時9分
Å`
SIE-id::
<When two parts are failed or lost>
Vehicle-id:
Parts required to replace or prepared when items on the left
Parts failed/lost Procedures to perform after parts replacement
fail
Access key
ID Body ID Body
Examples Combi- Combi-
function- All Collation Steering integ- Collation Steering integ-
Code ECM nation Access key Code ECM nation (1) (2) (3) (4) (5)
ing failed/ CM lock CM rated CM lock CM rated
Box meter Box meter
normally unit unit
lost
exists
60
Deletion of the Execution of smart
C type
Å`
SIE-id::
Parts required to replace or prepared when items on the left
Parts failed/lost Procedures to perform after parts replacement
fail
Vehicle-id:
Access key
ID Body ID Body
Examples Combi- Combi-
function- All Collation Steering integ- Collation Steering integ-
Code ECM nation Access key Code ECM nation (1) (2) (3) (4) (5)
ing failed/ CM lock CM rated CM lock CM rated
Box meter Box meter
normally unit unit
lost
exists
Steering lock
One registered Execution of smart
O O X X initialization work
access key ECM registration
(*1)
Execution of
One registered Execution of smart
O O X X (*4) engine ECM
access key ECM registration
registration
One registered Execution of smart
O O X X
access key ECM registration
One registered Execution of smart
O O X X
access key ECM registration
Execution of
O O X X engine ECM
registration
Execution of
O O X X engine ECM
registration
Execution of smart
One registered immobilizer
O O X X
access key registration
(*3)
61
C type
REGISTRATION MANUAL FOR IMMOBILIZER
S1001BE.fm 62 ページ 2014年4月30日 水曜日 午後2時9分
Å`
SIE-id::
<When three parts are failed or lost>
Vehicle-id:
Parts required to replace or prepared when items on the left
Parts failed/lost Procedures to perform after parts replacement
fail
Access key
ID Body ID Body
Examples Combi- Combi-
function- All Collation Steering integ- Collation Steering integ-
Code ECM nation Access key Code ECM nation (1) (2) (3) (4) (5)
ing failed/ CM lock CM rated CM lock CM rated
Box meter Box meter
normally unit unit
lost
exists
62
Deletion of the Execution of smart
C type
(*4)
access key ID immobilizer
One registered Execution of smart Execution of
O O O X X (deletion of the ID registration (when
access key ECM registration engine ECM
of a failed or lost an access key is
registration
access key) to be added)
Deletion of the Execution of smart
(*4)
access key ID immobilizer
One registered Execution of smart Execution of
O O O X X (deletion of the ID registration (when
access key ECM registration engine ECM
of a failed or lost an access key is
registration
access key) to be added)
Deletion of the Execution of smart
(*4)
access key ID immobilizer
One registered Execution of smart Execution of
O O O X X (deletion of the ID registration (when
access key ECM registration engine ECM
of a failed or lost an access key is
registration
access key) to be added)
Deletion of the Execution of smart
Execution of access key ID immobilizer
One registered
O O O X X engine ECM (deletion of the ID registration (when
access key
registration of a failed or lost an access key is
access key) to be added)
Deletion of the Execution of smart
Execution of access key ID immobilizer
One registered
O O O X X engine ECM (deletion of the ID registration (when
access key
registration of a failed or lost an access key is
access key) to be added)
REGISTRATION MANUAL FOR IMMOBILIZER
S1001BE.fm 63 ページ 2014年4月30日 水曜日 午後2時9分
Å`
SIE-id::
Parts required to replace or prepared when items on the left
Parts failed/lost Procedures to perform after parts replacement
fail
Vehicle-id:
Access key
ID Body ID Body
Examples Combi- Combi-
function- All Collation Steering integ- Collation Steering integ-
Code ECM nation Access key Code ECM nation (1) (2) (3) (4) (5)
ing failed/ CM lock CM rated CM lock CM rated
Box meter Box meter
normally unit unit
lost
exists
Deletion of the
Execution of smart
access key ID
immobilizer
One registered (deletion of the ID
O O O X X registration (when
access key of a failed or lost
an access key is
access key)
to be added)
(*3)
All access Execution of smart
O O O keys to be X X X immobilizer (*2)
registered registration
All access Execution of smart
O O O keys to be X X X immobilizer (*2)
registered registration
All access Execution of smart
O O O keys to be X X X immobilizer (*2)
registered registration
All access Execution of smart
O O O keys to be X X X immobilizer (*2)
registered registration
All access Execution of smart
O O O keys to be X X X immobilizer (*2)
registered registration
63
Execution of smart
All access
C type
immobilizer
O O O keys to be X X X (*2)
registration
registered
(*3)
Steering lock Execution of
One registered Execution of smart
O O O X X X initialization work (*4) engine ECM
access key ECM registration
(*1) registration
Steering lock Execution of
One registered Execution of smart
O O O X X X initialization work (*4) engine ECM
access key ECM registration
(*1) registration
Steering lock Execution of
One registered Execution of smart
O O O X X X initialization work (*4) engine ECM
access key ECM registration
(*1) registration
Steering lock Execution of
One registered Execution of smart
O O O X X X initialization work (*4) engine ECM
access key ECM registration
(*1) registration
Steering lock Execution of
One registered Execution of smart
O O O X X X initialization work (*4) engine ECM
access key ECM registration
(*1) registration
Steering lock
One registered Execution of smart
O O O X X X initialization work
access key ECM registration
(*1)
Execution of
One registered Execution of smart
O O O X X X (*4) engine ECM
access key ECM registration
registration
REGISTRATION MANUAL FOR IMMOBILIZER
S1001BE.fm 64 ページ 2014年4月30日 水曜日 午後2時9分
Å`
SIE-id::
Parts required to replace or prepared when items on the left
Parts failed/lost Procedures to perform after parts replacement
fail
Vehicle-id:
Access key
ID Body ID Body
Examples Combi- Combi-
function- All Collation Steering integ- Collation Steering integ-
Code ECM nation Access key Code ECM nation (1) (2) (3) (4) (5)
ing failed/ CM lock CM rated CM lock CM rated
Box meter Box meter
normally unit unit
lost
exists
Execution of
One registered Execution of smart
O O O X X X (*4) engine ECM
access key ECM registration
registration
Execution of smart Execution of
One registered
O O O X X X ECM registration (*4) engine ECM
access key
(*3) registration
Execution of
engine ECM
O O O X X X
registration
(*3)
*1: Steering lock initialization work: Initialization is complete if the steering is locked about 10 seconds after the ignition switch is turned off and driver's door was either opened then closed or closed then opened.
*2: When the collation CM has been replaced for a vehicle equipped with a remote control engine starter, perform “Registering Remote Control Engine Starter”.
*3: The registration work cannot be performed in the current state. Provide a new body integrated unit and then contact your Subaru service representative.
*4: Set the vehicle power supply to OFF and then back to IG ON.
64
C type
REGISTRATION MANUAL FOR IMMOBILIZER
S1001BE.fm 65 ページ 2014年4月30日 水曜日 午後2時9分
Å`
SIE-id::
6-10 Correspondence table when registration is not possible
Vehicle-id:
Status Screen Trouble mode Action to be taken
Select "Immobilizer" from the Main Menu→ •K line communication failure between Subaru Select Monitor and
•Perform the diagnosis for the K line.
System "Immobilizer" → Smart System NG Comm. Failed body integrated unit
•Check that the B/up fuse in the M/B is connected.
"NO" → IGN-ON "YES" → •B/up fuse disconnected
Security ID not written in either body integrated unit or combination
Communication error has occurred. Read out the security ID.
meter
"Smart Immobilizer Registration" start NG Security ID is incorrect x 3 times
Incorrect security ID Read out the security ID.
Enter the security ID → "Security ID is → initial screen
being collated." •Communication failure with combination meter (CAN
NG Security ID Registration communication related failure) Perform the diagnosis for CAN.
•Combination meter failure
•Check the data link connector and harness.
•Check that the B/up fuse in the M/B is connected.
•Check the data monitor of body integrated unit to confirm that the B/
up fuse is ON.
•Temporary communication failure with Subaru Select Monitor •Perform harness inspection between the power supply CM and push
(Collation CM replacement mode) •B/up fuse disconnected button ignition switch, and inspection of the push button ignition
→ "Initializing communication..." → Enter NG Mode transition error •Immobilizer amplifier failure switch alone, and check output of the immobilizer amplifier power
the security ID •Vehicle speed input exceeding 5 km/h (3 MPH) supply (VC5) (conduct from Work Support).
•ID code box response failure •Check that the vehicle speed is normal. (Make sure that the vehicle
speed pulse is not output from the direct line.)
•Check LIN between the collation CM and ID code box.
•Check for DTC, and if there is any, perform the diagnosis according
to the DTC. DTC : B2201, B2202, B2203, B2200, B2217
•Time-out before the operator held access key (30 seconds)
65
•Perform the procedure according to REGISTRATION MANUAL FOR
[No buzzer sounds, when access key is held] IMMOBILIZER.
C type
•Access key not held with its ornament surface facing push button
ignition switch [No buzzer sounds, when access key is held]
•Already-collated access key was held •Confirm the access key item number and check for malfunction.
NG Time Out •Another (already-collated) access key present near push button •Check that the access key is not registered on another vehicle.
ignition switch
* When the number of "Registered •Access key malfunction (transponder function) [Buzzer sounds only once when access key is held, and number of
number" does not increase after 30 •Access key incorrect item number (incorrect destination/incorrect registration does not increase]
seconds from displaying "Hold an system) •Check for DTC, and if there is any, perform the diagnosis according
(Collation CM replacement mode) Access Key to be registered over the •Access key that was registered on another vehicle was held to the DTC.
→ "Confirm all Access Keys..." start SW." screen. DTC : B2207
[Buzzer sounds only once when access key is held, and number of •Check that another access key is not present inside the vehicle.
→ "Hold an Access Key to be registered..." registration does not increase] •Check the battery of access key.
•Another access key present inside the vehicle (interference, etc.) •Check the access key for malfunction.
•Access key out of battery/malfunction (RF function) •Check the connector wiring/harness of RF receiver.
•RF receiver improper connection/malfunction •Check the front indoor antenna for malfunction.
•Front indoor antenna improper connection/malfunction
•Check for DTC, and if there is any, perform the diagnosis according
NG Time Out to the DTC.
•Steering lock CM or ID code box improper connection DTC : B2201, B2200, B2217
* When [END] is pressed after •CM code incompatibility between collation CM — steering lock CM •Check LIN between collation CM — power supply CM — ID code
holding of an access key is complete, — ID code box (control failure) box — steering lock CM.
or [YES] is pressed after "Registered •Code writing failure between CMs •Retry the procedure from the beginning.
number" becomes seven. (*Essentially neither writing incompatibility nor code incompatibility
occurs.)
REGISTRATION MANUAL FOR IMMOBILIZER
S1001BE.fm 66 ページ 2014年4月30日 水曜日 午後2時9分
Å`
SIE-id::
Status Screen Trouble mode Action to be taken
Vehicle-id:
[Following occurred during registration operation] [During registration operation, or during owner recognition]
•The operator pressed Quit button without registering access key •Check for DTC, and if there is any, perform the diagnosis according
to the DTC.
[Following failure occurred before none of new registration access key (DTC: B2203, B2204)
was collated during new registration key collation process after •Check the data link connector and harness.
registration mode is on.] •Perform harness inspection between the power supply CM and push
•Vehicle speed input exceeding 5 km/h (3 MPH) button ignition switch, and inspection of the push button ignition
•Immobilizer amplifier failure switch alone, and check output of the immobilizer amplifier power
•Temporary communication failure with Subaru Select Monitor supply (VC5) (conduct from Work Support).
•Check that the vehicle speed is normal. (Make sure that the vehicle
[When the following occurred during owner recognition] speed pulse is not output from the direct line.)
•Time-out before the operator held access key (30 seconds) •Retry the procedure from the beginning.
•Time-out while already-collated access key was kept held (30 (Check that the access key to be held is registered to the vehicle.)
seconds)
•Access key that was not registered to the vehicle was held [During owner recognition]
•Vehicle speed input exceeding 5 km/h (3 MPH) •Check that the access key is registered to the vehicle to be worked
•Immobilizer amplifier failure on.
•Access key not held with its ornament surface facing push button •Check the access key for malfunction.
ignition switch •Check for DTC, and if there is any, perform the diagnosis according
•Another (already-collated) access key present near push button to the DTC.
ignition switch DTC : B2201, B2200, B2217
•Access key malfunction (transponder function) •Check LIN between collation CM — power supply CM — ID code
•Access key incorrect item number (incorrect destination/incorrect box — steering lock CM.
→ "Ignition SW is turned off..." NG Steering LOCK (Time Out) system)
•Antenna coil malfunction [IGN OFF impossible]
•CM code incompatibility between collation CM — steering lock CM •Check for DTC, and if there is any, perform the diagnosis according
— ID code box (replacement with used part) to the DTC.
(DTC: B2105, B2106, B2107)
66
[IGN OFF impossible] •Check the harness between power supply CM and push button
•Operation not reflected due to push button ignition switch improper ignition switch, and push button ignition switch alone.
C type
connection/malfunction •Press the push button ignition switch a few times to check that the
•IGN relay stuck ON status changes as OFF → ACC ON → IGN ON.
•Power supply-output short in harness between power supply CM •Check the harness between power supply CM and IGN relay.
and IGN relay •Retry "Smart ECM Registration" only.
•IGN harness power supply-output short
•Shift positioned at other than P, or power supply CM falsely [Steering lock not confirmed]
recognizing as shift positioned at other than P •After initializing the steering lock, perform IGN ON and then execute
"Engine ECM Registration".
[Steering lock not confirmed] •On the data monitor of body integrated unit, check that "Driver’s
•Time-out before the operator performed IGN-OFF door open/close door SW input" changes ON-OFF according to the door opening/
(60 seconds) closing.
•Steering lock not connected, or LIN not connected (occurred during •Check for DTC, and if there is any, perform the diagnosis according
key registration procedure) to the DTC.
•Steering lock CM, ID code box, or power supply CM failure (control (DTC: B2201, B2200, B2217)
failure) •Check LIN between collation CM — power supply CM — ID code
•Door courtesy SW failure, or courtesy SW input failure of body box — steering lock CM.
integrated unit, G/W CM or collation CM •Replace the steering lock CM.
REGISTRATION MANUAL FOR IMMOBILIZER
S1001BE.fm 67 ページ 2014年4月30日 水曜日 午後2時9分
Å`
SIE-id::
Status Screen Trouble mode Action to be taken
Vehicle-id:
•Time-out before the operator performed IGN-ON (60 seconds) •Check for DTC, and if there is any, perform the diagnosis according
•Operation not reflected due to push button ignition switch improper to the DTC.
connection/malfunction (DTC: B2105, B2106, B2107)
•Access key not present inside the vehicle •Check if the access key is present inside the vehicle.
NG IGN ON (Time Out) •IGN relay stuck OFF •Press the push button ignition switch a few times to check that the
•GND-output short/open in harness between power supply CM and status changes as OFF → ACC ON → IGN ON.
IGN relay •Check the harness between power supply CM and IGN relay.
•IGN harness open/GND-output short •Check the upstream fuse of IGN relay.
→ "Switch Ignition ON" •IGN fuse blown out •Retry "Smart ECM Registration" only.
•While turning the steering wheel, perform IGN ON ←→ OFF to
check that the operation unlocks the steering lock.
•Check for DTC, and if there is any, perform the diagnosis according
•Steering lock CM locked
to the DTC.
NG Immobilizer Unsetting (Time Out) •Steering lock CM, ID code box, or collation CM failure (control
(DTC: B2201, B2200, B2217)
failure)
•Check LIN between collation CM — power supply CM — ID code
box — steering lock CM.
•Retry "Smart ECM Registration" only.
NG Number of registrations When an additional access key needs to be registered, delete the
Additional registration impossible
exceeded registered access key.
•Check the data link connector and harness.
•Check that the B/up fuse in the M/B is connected.
•Check the data monitor of body integrated unit to confirm that the B/
up fuse is ON.
•Perform harness inspection between the power supply CM and push
•Temporary communication failure with Subaru Select Monitor engine switch (push-button ignition switch), and inspection of the
(Additional registration mode)
"Smart Immobilizer Registration" start •B/up fuse disconnected push engine switch (push-button ignition switch) alone, and check
NG Mode transition error •Immobilizer amplifier failure output of the immobilizer amplifier power supply (VC5) (conduct
67
•Vehicle speed input exceeding 5 km/h (3 MPH) from Work Support).
•ID code box response failure •Check that the vehicle speed is normal. (Make sure that the vehicle
C type
Å`
SIE-id::
Status Screen Trouble mode Action to be taken
Vehicle-id:
•Perform the procedure again according to REGISTRATION
MANUAL FOR IMMOBILIZER.
(Check that the access key to be held is registered to the vehicle.)
(When either the ID code box or steering lock CM is replaced with a
new part, select "Smart ECM Registration".)
•Check for DTC, and if there is any, perform the diagnosis according
•Temporary communication failure with Subaru Select Monitor
to the DTC.
•Immobilizer amplifier failure
(DTC: B2202, B2203)
•Vehicle speed input exceeding 5 km/h (3 MPH)
•Check the data link connector and harness.
•ID code box response failure
•Check LIN between the collation CM and ID code box.
•Time-out before the registered access key being held (30 seconds)
•Check for DTC, and if there is any, perform the diagnosis according
•Access key not held with its ornament surface facing push button
→ "Confirming one of the registered to the DTC.
NG Mode transition error ignition switch
Access Key verification" (DTC: B2201, B2202, B2203, B2200, B2217)
•Access key malfunction (transponder function)
•Perform harness inspection between the power supply CM and push
•Access key incorrect item number (incorrect destination/incorrect
engine switch (push-button ignition switch), and inspection of the
system)
push engine switch (push-button ignition switch) alone, and check
•Antenna coil malfunction
output of the immobilizer amplifier power supply (VC5) (conduct
•CM code incompatibility between collation CM — steering lock CM
from Work Support).
— ID code box (control failure, replacement with used part)
•Check that the vehicle speed is normal. (Make sure that the vehicle
speed pulse is not output from the direct line.)
•Confirm the access key item number and check for malfunction.
•Check that the data monitor indicates "Normal" for "Code collated
result between collation ECM and ID code box" and "Code collation
result between steering locked ECM and ID code box".
•Time-out before the operator held access key (30 seconds)
•Perform the procedure according to REGISTRATION MANUAL FOR
[No buzzer sounds, when access key is held]
IMMOBILIZER.
•Access key not held with its ornament surface facing push button
68
ignition switch
[No buzzer sounds, when access key is held]
C type
Å`
SIE-id::
Status Screen Trouble mode Action to be taken
Vehicle-id:
[During registration operation, or during owner recognition]
[Following occurred during registration operation] •Check for DTC, and if there is any, perform the diagnosis according
•The operator pressed Quit button without registering access key to the DTC.
(DTC: B2203, B2204)
[Following failure occurred before none of new registration access key •Check the data link connector and harness.
was collated during new registration key collation process after
•Perform harness inspection between the power supply CM and push
registration mode is on.]
•Vehicle speed input exceeding 5 km/h (3 MPH) engine switch (push-button ignition switch), and inspection of the
•Immobilizer amplifier failure push engine switch (push-button ignition switch) alone, and check
•Temporary communication failure with Subaru Select Monitor output of the immobilizer amplifier power supply (VC5) (conduct
from Work Support).
[When the following occurred during owner recognition] •Check that the vehicle speed is normal. (Make sure that the vehicle
•Time-out before the operator held access key (30 seconds) speed pulse is not output from the direct line.)
•Time-out while already-collated access key was kept held (30 •Retry the procedure from the beginning.
seconds) (Check that the access key to be held is registered to the vehicle.)
•Access key that was not registered to the vehicle was held
•Vehicle speed input exceeding 5 km/h (3 MPH) [During owner recognition]
•Immobilizer amplifier failure •Check that the access key is registered to the vehicle to be worked
•Access key not held with its ornament surface facing push button on.
ignition switch •Check the access key for malfunction.
•Another (already-collated) access key present near push button •Check for DTC, and if there is any, perform the diagnosis according
ignition switch to the DTC.
•Access key malfunction (transponder function) (DTC: B2201, B2200, B2217)
•Access key incorrect item number (incorrect destination/incorrect •Check LIN between collation CM — power supply CM — ID code
system) box — steering lock CM.
→ "Ignition SW is turned off..." NG Steering LOCK (Time Out)
•Antenna coil malfunction
[IGN OFF impossible]
•CM code incompatibility between collation CM — steering lock CM
69
•Check for DTC, and if there is any, perform the diagnosis according
— ID code box (replacement with used part)
to the DTC.
C type
Å`
SIE-id::
Status Screen Trouble mode Action to be taken
Vehicle-id:
•Time-out before the operator performed IGN-ON (60 seconds) •Check for DTC, and if there is any, perform the diagnosis according
•Operation not reflected due to push button ignition switch improper to the DTC.
connection/malfunction (DTC: B2105, B2106, B2107)
•Access key not present inside the vehicle •Check if the access key is present inside the vehicle.
NG IGN ON (Time Out) •IGN relay stuck OFF •Press the push button ignition switch a few times to check that the
•GND-output short/open in harness between power supply CM and status changes as OFF → ACC ON → IGN ON.
IGN relay •Check the harness between power supply CM and IGN relay.
•IGN harness open/GND-output short •Check the upstream fuse of IGN relay.
→ "Switch Ignition ON" •IGN fuse blown out •Retry "Smart ECM Registration" only.
•While turning the steering wheel, perform IGN ON ←→ OFF to
check that the operation unlocks the steering lock.
•Check for DTC, and if there is any, perform the diagnosis according
•Steering lock CM locked
to the DTC.
NG Immobilizer Unsetting (Time Out) •Steering lock CM, ID code box, or collation CM failure (control
(DTC: B2201, B2200, B2217)
failure)
•Check LIN between collation CM — power supply CM — ID code
box — steering lock CM.
•Retry "Smart ECM Registration" only.
NG EGI-SSM Communication Check the communication line between ECM and Subaru Select
Communication failure with ECM
(Communication line judgment) Monitor. (K line or CAN line)
NG EGI-Immobilizer communication Communication failure between ECM and ID code box Perform the diagnosis for DTC B1572 (P1572).
NG IMM Control Module EEPROM ID code box failure Perform the diagnosis for DTC B1577 (P1577).
(All mode)
→ "EGI initialization / During registration..." NG EGI unit EEPROM ECM failure Perform the diagnosis for DTC B1576 (P1576).
•Subaru Select Monitor failure •Check version of Subaru Select Monitor.
NG EGI security access NG
•ECM failure •Replace the ECM.
Wait until the self shut completes, and retry the procedure. When this
70
NG EGI-SSM Communication ECM failure
does not solve the problem, remove and install the battery.
C type
Å`
SIE-id::
Status Screen Trouble mode Action to be taken
Vehicle-id:
•Check the data link connector and harness.
•Perform harness inspection between the power supply CM and push
engine switch (push-button ignition switch), and inspection of the
push engine switch (push-button ignition switch) alone, and check
output of the immobilizer amplifier power supply (VC5) (conduct
•Temporary communication failure with Subaru Select Monitor from Work Support).
•Immobilizer amplifier failure •Check that the B/up fuse in the M/B is connected.
NG Mode transition error •Vehicle speed input exceeding 5 km/h (3 MPH) •Check the data monitor of body integrated unit to confirm that the B/
•ID code box response failure up fuse is ON.
•B/up fuse disconnected •Check that the vehicle speed is normal. (Make sure that the vehicle
speed pulse is not output from the direct line.)
•Check LIN between the collation CM and ID code box.
•Check for DTC, and if there is any, perform the diagnosis according
to the DTC.
(DTC: B2201, B2202, B2203, B2200, B2217)
•Perform the procedure again according to REGISTRATION
MANUAL FOR IMMOBILIZER.
(Check that the access key to be held is registered to the vehicle.)
(When either the ID code box or steering lock CM is replaced with a
new part, select "Smart ECM Registration".)
→ "Confirming one of the registered •Time-out before the registered access key being held (30 seconds)
•Check for DTC, and if there is any, perform the diagnosis according
Access Key verification" •Access key not held with its ornament surface facing push button
to the DTC.
ignition switch
(DTC: B2202, B2203)
NG Time Out •Access key malfunction (transponder function)
•Perform harness inspection between the power supply CM and push
•Access key incorrect item number (incorrect destination/incorrect
* When holding an access key button ignition switch, and inspection of the push button ignition
system)
71
switch alone, and check output of the immobilizer amplifier power
•Antenna coil malfunction
supply (VC5) (conduct from Work Support).
C type
Å`
SIE-id::
Status Screen Trouble mode Action to be taken
Vehicle-id:
NG EGI-SSM Communication Check the communication line between ECM and Subaru Select
Communication failure with ECM
(Communication line judgment) Monitor. (K line or CAN line)
NG EGI-Immobilizer communication Communication failure between ECM and ID code box Perform the diagnosis for DTC B1572 (P1572).
NG IMM Control Module EEPROM ID code box failure Perform the diagnosis for DTC B1577 (P1577).
→ "Engine ECM is registering..." NG EGI unit EEPROM ECM failure Perform the diagnosis for DTC B1576 (P1576).
•Subaru Select Monitor failure •Check version of Subaru Select Monitor.
NG EGI security access NG
•ECM failure •Replace the ECM.
Wait until the self shut completes, and retry the procedure. When this
NG EGI-SSM Communication ECM failure
does not solve the problem, remove and install the battery.
Security ID not written in either body integrated unit or combination
Communication error has occurred. Read out the security ID.
meter
NG Security ID is incorrect x 3 times
Incorrect security ID Read out the security ID.
→ initial screen
•Communication failure with combination meter (CAN
NG Security ID Registration communication related failure) Perform the diagnosis for CAN.
•Combination meter failure
Can not delete anything more. Not enough number of access keys to delete registered Execute "Smart Immobilizer Registration".
•Check the data link connector and harness.
•Check that the B/up fuse in the M/B is connected.
"Delete the Access Key ID" start •Check the data monitor of body integrated unit to confirm that the B/
Enter the security ID → "Security ID is up fuse is ON.
being collated." •Perform harness inspection between the power supply CM and push
•Temporary communication failure with Subaru Select Monitor engine switch (push-button ignition switch), and inspection of the
•B/up fuse disconnected push engine switch (push-button ignition switch) alone, and check
NG Mode transition error •Immobilizer amplifier failure output of the immobilizer amplifier power supply (VC5) (conduct
72
•Vehicle speed input exceeding 5 km/h (3 MPH) from Work Support).
C type
•ID code box response failure •Check that the vehicle speed is normal. (Make sure that the vehicle
speed pulse is not output from the direct line.)
•Check LIN between the collation CM and ID code box.
•Check for DTC, and if there is any, perform the diagnosis according
to the DTC.
(DTC: B2201, B2202, B2203, B2200, B2217)
REGISTRATION MANUAL FOR IMMOBILIZER
S1001BE.fm 73 ページ 2014年4月30日 水曜日 午後2時9分
Å`
SIE-id::
Status Screen Trouble mode Action to be taken
Vehicle-id:
•Perform the procedure again according to REGISTRATION
MANUAL FOR IMMOBILIZER.
(Check that the access key to be held is registered to the vehicle.)
•Time-out before the registered access key being held (30 seconds)
(When either the ID code box or steering lock CM is replaced with a
•Vehicle speed input exceeding 5 km/h (3 MPH)
new part, select "Smart ECM Registration".)
•Immobilizer amplifier failure
•Check for DTC, and if there is any, perform the diagnosis according
•Access key not held with its ornament surface facing push button
to the DTC.
ignition switch
(DTC: B2200, B2201, B2217, B2202, B2203)
•Another (already-collated) access key present near push button
•Perform harness inspection between the collation CM and push
ignition switch
→ "Confirming one of the registered button ignition switch, and inspection of the push button ignition
NG Time Out •Access key malfunction (transponder function)
Access Key verification" switch alone, and check output of the immobilizer amplifier power
•Access key incorrect item number (incorrect destination/incorrect
supply (VC5) (conduct from Work Support).
system)
•Check that the vehicle speed is normal. (Make sure that the vehicle
•Antenna coil malfunction
speed pulse is not output from the direct line.)
•Steering lock CM or ID code box improper connection
•Confirm the access key item number and check for malfunction.
•CM code incompatibility between collation CM — steering lock CM
•Check LIN between collation ECM — power supply CM — ID code
— ID code box (control failure)
box — steering lock CM.
•Code writing failure between CMs
•Check that the data monitor indicates "Normal" for "Code collated
result between collation ECM and ID code box" and "Code collation
result between steering locked ECM and ID code box".
73
C type
REGISTRATION MANUAL FOR IMMOBILIZER
S1001BE.fm 74 ページ 2014年4月30日 水曜日 午後2時9分
D type
REGISTRATION MANUAL FOR IMMOBILIZER
7 D type C: Caution
Vehicle that has a keyless access with push button • When you install wireless radios or car
start system and is originally NOT provided with a phones, make sure that the immobilizer
security ID (security tag) system is not influenced by their electric
waves.
A: Structure • Do not operate cell phones or wireless radios
or the like when either trouble diagnosis or
An immobilizer system consists of the following immobilizer registration is in progress.
components: Immobilizer indicator (in the • During immobilizer registration, do not bring a
combination meter), ECM, access key, immobilizer key with a different ID close to the ignition
antenna (incorporating a push switch), keyless switch. When the access key is on a keychain,
access CM, steering lock CM, ID code box (for a remove it from the chain before start of
model with ID code box), indoor and outdoor diagnosis. When there are several keys on one
antennas, and receiver (may be incorporated in keychain, remove them from the keychain and
keyless access CM). use them individually for the work.
B: Operation • The work of "Registering the Smart
Immobilizer", "Registering the Smart ECM"
Get in the vehicle with your access key and let the and "Delete the Mobile Key (Access Key) ID"
access key send the ID via the indoor antenna. The includes the operation of holding up the
access key sends the ID to the receiver and the access key to the push engine switch (push-
received ID is sent to the collation CM where it is button ignition switch). Pay attention to the
collated with the IDs of other immobilizer-related following when performing this operation.
units. Step on the brake pedal (for an AT model) or • Confirm that the battery voltage is 11 V or
clutch pedal (for a MT model) and press the push more and execute each mode.
engine switch so that the starter rotates to start the • When confirm/register access key, only
engine. one key can be brought into vehicle at a
time. For registration of multiple keys,
If the IDs do not match within the specified period of
bring a key into vehicle and perform
time after the RPM of the engine reaches the
registration while leaving rest of other
specified RPM, the engine stops. If the IDs do not keys outside.
match, the engine stops within a couple of • When holding up the access key to the
seconds. If the engine does not start as a result of push engine switch (push-button ignition
a mismatch of the IDs, the immobilizer indicator switch), do not hold two or more access
lamp in the combination meter turns on to indicate keys at the same time, but use only one
that the immobilizer is active. When the immobilizer each time. (When the access key is on a
is activated, the immobilizer indicator lamp flashes keychain, remove it from the keychain
to generate an alert notifying people around the before the work.)
vehicle that it is protected by the immobilizer. • When holding the access key up to the
push engine switch (push-button ignition
switch), bring the access key close to the
push engine switch (push-button ignition
switch) as shown below.
IM-00482
74
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 75 ページ 2014年4月30日 水曜日 午後2時9分
D type
REGISTRATION MANUAL FOR IMMOBILIZER
75
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 76 ページ 2014年4月30日 水曜日 午後2時9分
D type
REGISTRATION MANUAL FOR IMMOBILIZER
7-1 Adding Access Keys 5) On the next screen, confirm the system is
keyless access with push button start system.
Note:
Click the [YES] button.
Depending on the replacement part, a different
screen from the screen shown in this item may be
displayed. In such a case, follow the instructions
shown on the screens.
1) Start the PC application according to section
"Starting Up the System" and display the Main
Menu screen. (Refer to "PC application help for
Subaru Select Monitor".)
2) On the Main Menu, select [All other models].
IM-00437
Note:
The term [smart system] that appears on this
screen is synonymous with the term [keyless
access with push button start system] used in this
text.
6) The registration mode selection dialog box
appears. Click the [Smart Immobilizer
IM-00491 Registration] button.
IM-00492
IM-00404
Note:
Audio System is the specification only for the U.K.
76
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 77 ページ 2014年4月30日 水曜日 午後2時9分
D type
REGISTRATION MANUAL FOR IMMOBILIZER
8) The dialog box to confirm already registered 9) When screen displays access key registration
access keys appears. Hold one of those access mode shown below, hold one access key you
keys over the push engine switch (push-button wish to register additionally over the push
ignition switch). After the buzzer sounds once, engine switch (push-button ignition switch).
move the access key away from the push
engine switch (push-button ignition switch) and
go to the next step.
Note:
• When the buzzer has sounded twice, the work of
holding the access key up has been completed,
Note: but for 10 seconds after the work, the access key
• When holding the access key up to the push should be kept inside the vehicle (near the select
engine switch (push-button ignition switch), bring lever).
the access key close to the push engine switch • For registration of the next access key, the
(push-button ignition switch) as shown below. previously registered access key should be
removed from the vehicle.
• Do not click the [Quit] button until you finish
registering all the access keys you wish to
register.
• The procedure to hold an access key over the
push engine switch (push-button ignition switch)
has to be done within 30 seconds after the
screen above appears.
IM-00482 10) Once the registration ends normally, the
(1) Let the mechanical key insertion opening of [Registered number] increases by one as you
the access key face down. can see on the screen below. If you have
(2) Face the access key with the button surface another access key to be registered, repeat
facing yourself. step 9. If you do not have any more keys to be
(3) Bring it close until it touches the push registered, click the [Quit] button and move on
engine switch (push-button ignition switch). to step 11.
• The procedure to hold an access key over the
push engine switch (push-button ignition switch)
has to be done within 30 seconds after the
screen above appears.
77
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 78 ページ 2014年4月30日 水曜日 午後2時9分
D type
REGISTRATION MANUAL FOR IMMOBILIZER
11) When the "Turn off the ignition switch" screen 7-2 Registering Keyless Access CU
appears, turn the push engine switch (push-
Caution:
button ignition switch) off.
All registered access keys are required. If
12) Then following screen appears. Turn the
registration completed before registering a
ignition on.
desired access key, such an unregistered
access key cannot be used anymore. When
necessary, prepare a new access key, and
perform additional registration.
Note:
Depending on the replacement part, a different
screen from the screen shown in this item may be
displayed. In such a case, follow the instructions
shown on the screens.
1) Start the PC application according to section
13) Stand by as the registration to the ECM is being "Starting Up the System" and display the Main
completed. Menu screen. (Refer to "PC application help for
Subaru Select Monitor".)
2) On the Main Menu, select [All other models].
IM-00445
IM-00446
78
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 79 ページ 2014年4月30日 水曜日 午後2時9分
D type
REGISTRATION MANUAL FOR IMMOBILIZER
4) Click the [YES] button if the System Check 6) The registration mode selection dialog box
screen is displayed. appears. Click the [Smart Immobilizer
Registration] button.
Note:
If the command input screen is displayed instead of
the menu screen, the vehicle is C type. See the
procedures for C type vehicle.
IM-00404
Note:
Audio System is the specification only for the U.K.
5) On the next screen, confirm the system is
keyless access with push button start system. IM-00438
Click the [YES] button. 7) On the registration mode confirmation dialog
box that appears, click the [OK] button.
8) When "Execute smart ECM replacement
registration" appears, click the [OK] button.
9) When the access key confirmation screen
appears, hold up the access key that was
registered to the new keyless access CM to the
push engine switch (push-button ignition
switch). After the buzzer has sounded once,
IM-00437 move the access key away from the push
engine switch (push-button ignition switch).
Note:
Note:
The term [smart system] that appears on this
• When holding the access key up to the push
screen is synonymous with the term [keyless engine switch (push-button ignition switch), bring
access with push button start system] used in this the access key close to the push engine switch
text. (push-button ignition switch) as shown below.
IM-00482
79
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 80 ページ 2014年4月30日 水曜日 午後2時9分
D type
REGISTRATION MANUAL FOR IMMOBILIZER
• The procedure to hold an access key over the 13) When the "Turn off the ignition switch" screen
push engine switch (push-button ignition switch) appears, turn the push engine switch (push-
has to be done within 30 seconds after the
button ignition switch) off.
screen above appears.
10) If confirmation is successful, the remaining 14) Then following screen appears. Turn the
number decreases by 1. Repeat the ignition on.
confirmation work of step 9 until the remaining
number becomes 0.
11) When screen displays access key registration
mode shown below, hold one access key you
wish to register over the push engine switch
(push-button ignition switch).
Note:
• When the buzzer has sounded twice, the work of
holding the access key up has been completed, but
for 10 seconds after the work, the access key should
be kept inside the vehicle (near the select lever).
• For registration of the next access key, the
previously registered access key should be IM-00445
removed from the vehicle.
• Do not click the [Quit] button until you finish 16) The screen shown below will appear if
registering all the access keys you wish to registration ends normally. Click the [OK]
register.
button.
• The procedure to hold an access key over the
push engine switch (push-button ignition switch)
has to be done within 30 seconds after the
screen above appears.
12) Once the registration ends normally, the
[Registered number] increases by one as you
can see on the screen below. If you have
another access key to be registered, repeat
step 11. If you do not have any more keys to be
registered, click the [Quit] button and move on
to step 13.
IM-00446
80
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 81 ページ 2014年4月30日 水曜日 午後2時9分
D type
REGISTRATION MANUAL FOR IMMOBILIZER
7-3 Registering the Steering Lock CU 5) On the next screen, confirm the system is
or ID Code Box keyless access with push button start system.
1) Start the PC application according to section Click the [YES] button.
"Starting Up the System" and display the Main
Menu screen. (Refer to "PC application help for
Subaru Select Monitor".)
2) On the Main Menu, select [All other models].
IM-00437
Note:
The term [smart system] that appears on this
screen is synonymous with the term [keyless
IM-00491 access with push button start system] used in this
3) Select [Immobilizer] from the item selection text.
dialog box. 6) The registration mode selection dialog box
appears. Click the [Smart ECM Registration]
button.
Note:
If the command input screen is displayed instead of
the menu screen, the vehicle is C type. See the
procedures for C type vehicle.
IM-00492
IM-00447
IM-00404
Note:
Audio System is the specification only for the U.K.
IM-00448
81
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 82 ページ 2014年4月30日 水曜日 午後2時9分
D type
REGISTRATION MANUAL FOR IMMOBILIZER
8) The dialog box to confirm already registered 9) Smart ECM registration is then automatically
access keys appears. Hold one of those access executed. When the registration ends normally,
keys over the push engine switch (push-button the following screen appears. Click the [OK]
ignition switch). After the buzzer sounds once, button.
move the access key away from the push
engine switch (push-button ignition switch) and
go to the next step.
IM-00451
IM-00482
82
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 83 ページ 2014年4月30日 水曜日 午後2時9分
D type
REGISTRATION MANUAL FOR IMMOBILIZER
7-4 Registering the Engine ECM 5) On the next screen, confirm the system is
keyless access with push button start system.
1) Start the PC application according to section
Click the [YES] button.
"Starting Up the System" and display the Main
Menu screen. (Refer to "PC application help for
Subaru Select Monitor".)
2) On the Main Menu, select [All other models].
IM-00437
Note:
The term [smart system] that appears on this
IM-00491 screen is synonymous with the term [keyless
access with push button start system] used in this
3) Select [Immobilizer] from the item selection
text.
dialog box.
6) Click [YES] after confirming if the ignition switch
is ON, as following screen will be displayed.
IM-00492
IM-00404
Note:
Audio System is the specification only for the U.K.
IM-00452
83
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 84 ページ 2014年4月30日 水曜日 午後2時9分
D type
REGISTRATION MANUAL FOR IMMOBILIZER
8) On the registration mode confirmation dialog 7-5 Readout the Number of Access
box that appears, click the [OK] button. Key Registration
1) Start the PC application according to section
"Starting Up the System" and display the Main
Menu screen. (Refer to "PC application help for
Subaru Select Monitor".)
2) On the Main Menu, select [All other models].
IM-00453
IM-00445
IM-00446
84
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 85 ページ 2014年4月30日 水曜日 午後2時9分
D type
REGISTRATION MANUAL FOR IMMOBILIZER
5) On the next screen, confirm the system is 8) The number of access keys currently registered
keyless access with push button start system. will be displayed. After clicking the [OK] button,
Click the [YES] button. the screen will return to the main menu.
IM-00437 IM-00457
Note:
The term [smart system] that appears on this
screen is synonymous with the term [keyless
access with push button start system] used in this
text.
6) The registration mode selection dialog box
appears. Click the [Readout the number of
mobile key registration] button.
Note:
If the command input screen is displayed instead of
the menu screen, the vehicle is C type. See the
procedures for C type vehicle.
IM-00455
IM-00456
85
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 86 ページ 2014年4月30日 水曜日 午後2時9分
D type
REGISTRATION MANUAL FOR IMMOBILIZER
7-6 Delete the Access Key ID 5) On the next screen, confirm the system is
keyless access with push button start system.
1) Start the PC application according to section
Click the [YES] button.
"Starting Up the System" and display the Main
Menu screen. (Refer to "PC application help for
Subaru Select Monitor".)
2) On the Main Menu, select [All other models].
IM-00437
Note:
The term [smart system] that appears on this
IM-00491 screen is synonymous with the term [keyless
access with push button start system] used in this
3) Select [Immobilizer] from the item selection
text.
dialog box.
6) The registration mode selection dialog box
appears. Click the [Delete the mobile key ID]
button.
Note:
If the command input screen is displayed instead of
the menu screen, the vehicle is C type. See the
procedures for C type vehicle.
IM-00492
IM-00458
Note:
Audio System is the specification only for the U.K.
IM-00459
86
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 87 ページ 2014年4月30日 水曜日 午後2時9分
D type
REGISTRATION MANUAL FOR IMMOBILIZER
8) As the number of registered access keys 9) The screen shown below will appear if access
confirmation screen will be displayed, place key ID deletion ends normally. Click the [OK]
one of the registered access keys, the key, button.
which you do not want to delete the ID, over the
push engine switch (push-button ignition
switch). After the buzzer sounds once, move
the access key away from the push engine
switch (push-button ignition switch) and go to
the next step.
IM-00462
Note:
• When holding the access key up to the push
engine switch (push-button ignition switch), bring
the access key close to the push engine switch
(push-button ignition switch) as shown below.
IM-00482
87
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 88 ページ 2014年4月30日 水曜日 午後2時9分
D type
REGISTRATION MANUAL FOR IMMOBILIZER
7-7 Registering Remote Control 5) On the next screen, confirm the system is
Engine Starter keyless access with push button start system.
1) Start the PC application according to section Click the [YES] button.
"Starting Up the System" and display the Main
Menu screen. (Refer to "PC application help for
Subaru Select Monitor".)
2) On the Main Menu, select [All other models].
IM-00437
Note:
The term [smart system] that appears on this
screen is synonymous with the term [keyless
IM-00491 access with push button start system] used in this
3) Select [Immobilizer] from the item selection text.
dialog box. 6) The registration mode selection dialog box
appears. Click the [Remote Control Engine
Starter Registration] button.
Note:
If the command input screen is displayed instead of
the menu screen, the vehicle is C type. See the
procedures for C type vehicle.
IM-00492
IM-00463
IM-00404
Note:
Audio System is the specification only for the U.K.
IM-00464
88
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 89 ページ 2014年4月30日 水曜日 午後2時9分
D type
REGISTRATION MANUAL FOR IMMOBILIZER
8) Wait until the remote control engine starter is 7-8 Reading Registration History
then being registered.
Note:
Depending on the replacement parts, a screen
displays other than indicated in this section may be
displayed. In such a case, follow the instructions
shown on the screens.
1) Start the PC application according to section
"Starting Up the System" and display the Main
Menu screen. (Refer to "PC application help for
Subaru Select Monitor".)
IM-00465
2) On the Main Menu, select [All other models].
9) The screen shown below will appear if remote
control engine starter registration ends
normally. Click the [OK] button.
IM-00491
IM-00492
IM-00404
Note:
Audio System is the specification only for the U.K.
89
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 90 ページ 2014年4月30日 水曜日 午後2時9分
D type
REGISTRATION MANUAL FOR IMMOBILIZER
IM-00437
IM-00603
Note:
The term [smart system] that appears on this 8) Check the displayed Read registration history
screen is synonymous with the term [keyless screen, and click the [OK] button.
access with push button start system] used in this Note:
text. For the details, refer to "7-12 List of registration
6) The registration mode selection screen history".
appears. Click the [Read registration history]
button.
Note:
If the command input screen is displayed instead of
the menu screen, the vehicle is C type. See the
procedures for C type vehicle.
IM-00602
90
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 91 ページ 2014年4月30日 水曜日 午後2時9分
Å`
SIE-id::
7-9 Keyless access with push button start system (when ID code box (U.K./CANADA)) : Correspondence
Vehicle-id:
table at the time of parts failure
If all the keys are lost, for protection against vehicle theft you must contact your Subaru service representative.
Caution:
Parts to be replaced always shall be replaced by new parts, never by used parts.
Delete the access key ID Leave the ID of one access key and delete all others. (One is required at the time of One registered access key
mode execution.)
Registering Engine ECM Perform registration between ECM and ID code box. All parts other than the ECM need to have been registered.
Registering the Remote Control
When a remote control engine starter has been installed.
Engine Starter
91
Immobilizer] even when ignition switch is OFF.)
D type
Å`
SIE-id::
<When two parts are failed or lost>
Vehicle-id:
Parts required to replace or prepared when
Parts failed/lost Procedures to perform after parts replacement
items on the left fail
Access key Keyless ID Keyless ID
Steering Steering
access Code ECM Access key access Code ECM (1) (2) (3) (4)
Not all All lock CM lock CM
CM Box CM Box
Execution of smart
Execution of access key
immobilizer registration
One registered Execution of smart ECM ID deletion (*1)
O O X (*1)
access key registration (deletion of the ID of a
(registration of additional
failed or lost access key)
access key)
Execution of smart
Execution of access key
Set the vehicle power immobilizer registration
One registered Execution of smart ECM Execution of engine ID deletion (*1)
O O X supply to OFF and then (*1 )
access key registration ECM registration (deletion of the ID of a
back to IG-ON. (registration of additional
failed or lost access key)
access key)
Execution of smart
Execution of access key
immobilizer registration
One registered Execution of engine ID deletion (*1)
O O X (*1)
access key ECM registration (deletion of the ID of a
(registration of additional
failed or lost access key)
access key)
All access
Execution of smart
O O keys to be reg- X X (*2)
immobilizer registration
istered
All access
Execution of smart
O O keys to be reg- X X (*2)
immobilizer registration
istered
92
Set the vehicle power
One registered Execution of smart ECM Execution of engine
O O X X supply to OFF and then
D type
Å`
SIE-id::
<When three parts are failed or lost>
Vehicle-id:
Parts required to replace or prepared when
Parts failed/lost Procedures to perform after parts replacement
items on the left fail
Access key Keyless ID Keyless ID
Steering Steering
access Code ECM Access key access Code ECM (1) (2) (3) (4)
Not all All lock CM lock CM
CM Box CM Box
Execution of smart
Execution of access key
Set the vehicle power immobilizer
One registered Execution of smart ECM Execution of engine ID deletion (*1)
O O O X X supply to OFF and then registration(*1 )
access key registration ECM registration (deletion of the ID of a
back to IG-ON. (registration of additional
failed or lost access key)
access key)
Execution of smart
Execution of access key
Set the vehicle power immobilizer
One registered Execution of smart ECM Execution of engine ID deletion (*1)
O O O X X supply to OFF and then registration(*1 )
access key registration ECM registration (deletion of the ID of a
back to IG-ON. (registration of additional
failed or lost access key)
access key)
Execution of smart
Execution of access key
Set the vehicle power immobilizer
One registered Execution of smart ECM Execution of engine ID deletion (*1)
O O O X X supply to OFF and then registration(*1)
access key registration ECM registration (deletion of the ID of a
back to IG-ON. (registration of additional
failed or lost access key)
access key)
All access
Execution of smart
O O O keys to be reg- X X X (*2)
immobilizer registration
istered
Set the vehicle power
One registered Execution of smart ECM Execution of engine
O O O X X X supply to OFF and then
access key registration ECM registration
back to IG-ON.
93
D type
*1 : Execute if necessary.
*2 : When the keyless access CM has been replaced for a vehicle equipped with a remote control engine starter, perform “Registering Remote Control Engine Starter”.
REGISTRATION MANUAL FOR IMMOBILIZER
S1001BE.fm 94 ページ 2014年4月30日 水曜日 午後2時9分
Å`
SIE-id::
7-10 Keyless access with push button start system (when no ID code box (except for U.K./CANADA)):
Vehicle-id:
Correspondence table at the time of parts failure
If all the keys are lost, for protection against vehicle theft you must contact your Subaru service representative.
Caution:
Parts to be replaced always shall be replaced by new parts, never by used parts.
94
Immobilizer] even when ignition switch is OFF.)
D type
Å`
SIE-id::
<When two parts are failed or lost>
Vehicle-id:
Parts required to replace or prepared when
Parts failed/lost Procedures to perform after parts replacement
items on the left fail
Access key Keyless Keyless
Steering Steering
access ECM Access key access ECM (1) (2) (3) (4)
Not all All lock CM lock CM
CM CM
95
Execution of access key ID
(*2) deletion Execution of smart immobilizer
D type
Å`
SIE-id::
7-11 Correspondence table when registration is not possible
Vehicle-id:
Registration history that
Status Screen Trouble mode Action to be taken
possibly remains
Select "Immobilizer" from the Main
Menu → System "Immobilizer" → CAN communication failure between Subaru Select Monitor
NG Comm. Failed Perform the diagnosis for CAN. —
Smart System "NO" → IGN-ON "YES" and keyless access CM
→
•Without ID code box: Check if IDW terminal is not connected
or is grounded.
•With ID code box: Check that IDW terminal is connected to
•ID code box presence judgment circuit failure (harness setting •Failure of the condition
ground.
NG Abnormal failure) -vehicle speed detection
•Check that the B/up fuse in the M/B or F/B is connected.
Termination •B/up fuse disconnected -different ID code box setting
•Check the data monitor of body integrated unit to confirm that
•Vehicle speed input exceeding 5 km/h (3 MPH) -Among special mode
the B/up fuse is ON.
•Check that the vehicle speed is normal. (Make sure that the
vehicle speed pulse is not output from the direct line.)
(Smart ECM replacement mode) •Check the data link connector and harness.
→ "Perform the [Smart Immobilizer
•Perform harness inspection between the keyless access CM
Registration]"
→ "Registration mode during and push button ignition switch, and inspection of the push
migration." button ignition switch alone, and check output of the
immobilizer amplifier power supply (VC5) (conduct from Work
•Temporary communication failure with Subaru Select Monitor
Support). •Failure of the condition
NG Mode transition •Immobilizer amplifier failure
•Check that the vehicle speed is normal. (Make sure that the -vehicle speed detection
error •Vehicle speed input exceeding 5 km/h (3 MPH)
vehicle speed pulse is not output from the direct line.) -diag. communication failure
•ID code box response failure
•For the vehicle with ID code box, check LIN between keyless
access CM and ID code box.
96
•Check for DTC, and if there is any, perform the diagnosis
D type
Å`
SIE-id::
Registration history that
Status Screen Trouble mode Action to be taken
possibly remains
Vehicle-id:
•Perform the procedure again according to REGISTRATION
MANUAL FOR IMMOBILIZER. (Check if owner recognition is
•Time-out before the operator held access key (30 seconds)
performed for all access keys.)
•Already-collated access key was held
•Check for DTC, and if there is any, perform the diagnosis
•Vehicle speed input exceeding 5 km/h (3 MPH)
according to the DTC. •push-button SW amp error
•Immobilizer amplifier failure
(DTC: B2789, B2790, B2786, B2785, B278A, B2784) •Owner key’s check fail
•Access key not held over the push button ignition switch with
•Check LIN between the keyless access CM and steering lock -hold up the collated key just
(Smart ECM replacement mode) the button surface facing yourself
CM or ID code box. before
→ "Perform the [Smart ECM NG Check the owner •Another (already-collated) access key present near push
•Perform harness inspection between the keyless access CM •Failure of the condition
replacement and registration]" NG button ignition switch
and push button ignition switch, and inspection of the push -LIN communication failure
→ "The owner is confirmed" •Access key malfunction (transponder function)
button ignition switch alone, and check output of the •Different code between ECM
•Access key incorrect item number (incorrect destination/
immobilizer amplifier power supply (VC5) (conduct from Work -Between ID code box
incorrect system)
Support). -Between Steering lock CM
•Antenna coil malfunction
•Check that the vehicle speed is normal. (Make sure that the
•Steering lock CM or ID code box improper connection
vehicle speed pulse is not output from the direct line.)
•Keyless access CM, steering lock CM, or ID code box failure
•Confirm the access key item number and check for
malfunction.
•Time-out before the operator held the key (30 seconds) •Perform the procedure according to REGISTRATION
MANUAL FOR IMMOBILIZER.
[No buzzer sounds, when access key is held]
•Access key not held over the push button ignition switch with [No buzzer sounds, when access key is held]
the button surface facing yourself •Confirm the access key item number and check for
•Another (already-collated) access key present near push malfunction.
button ignition switch
•Access key malfunction (transponder function) [Buzzer sounds only once when access key is held, and
NG Time-out •New key’s check fail
•Access key incorrect item number (incorrect destination/ number of registration does not increase]
→ "Register the Access Key." occurred during -hold up the collated key just
incorrect system) •Check for DTC, and if there is any, perform the diagnosis
Access Key collation before
according to the DTC.
[Buzzer sounds only once when access key is held, and (DTC: B1242, B27A5)
number of registration does not increase] •Check that another access key is not present inside the
97
•Another access key present inside the vehicle (interference, vehicle.
etc.) •Check the battery of access key.
D type
•Access key out of battery/malfunction (RF function) •Check the access key for malfunction.
•RF receiver connection •Check the connector wiring/harness of RF receiver.
•Front indoor antenna improper connection/malfunction •Check the front indoor antenna for malfunction.
•Check for DTC, and if there is any, perform the diagnosis
NG While Access •Steering lock CM or ID code box improper connection according to the DTC.
Key is registering, •ECM code incompatibility between keyless access CM and (DTC: B2785, B2786, B2789) •Time-out
timeout has steering lock CM or ID code box (control failure) •Check LIN between the keyless access CM and ID code box -no ECM reply mismatch
occurred. •Code writing failure between ECMs or steering lock CM.
•Retry the procedure from the beginning.
•Check for DTC, and if there is any, perform the diagnosis
according to the DTC.
•ECM code incompatibility between keyless access CM and •Failure of the condition
(DTC: B2789, B2790, B2786, B2785, B278A, B2784)
steering lock CM or ID code box (control failure) -vehicle speed detection
•Check LIN between the keyless access CM and steering lock
→ "Access Key is registering..." •The operator pressed Quit button without registering key -diag. communication failure
CM or ID code box.
-LIN communication failure
[Following failure occurred before none of new registration •Check the data link connector and harness.
NG Failed to •Access key PW difference
access key was collated during new registration key collation •Perform harness inspection between the keyless access CM
Portable Device process after registration mode is on.] •Writing failure
Registration and push button ignition switch, and inspection of the push
•Vehicle speed input exceeding 5 km/h (3 MPH) -ECM code (ID code box)
button ignition switch alone, and check output of the
•Immobilizer amplifier failure -ECM code (Steering lock
immobilizer amplifier power supply (VC5) (conduct from Work
•Temporary communication failure with Subaru Select Monitor ECM)
Support).
•Steering lock CM or ID code box improper connection -Keyless access CM
•Check that the vehicle speed is normal. (Make sure that the
•Keyless access CM, steering lock CM, or ID code box failure reg info
vehicle speed pulse is not output from the direct line.)
•Retry the procedure from the beginning.
REGISTRATION MANUAL FOR IMMOBILIZER
S1001BE.fm 98 ページ 2014年4月30日 水曜日 午後2時9分
Å`
SIE-id::
Registration history that
Status Screen Trouble mode Action to be taken
possibly remains
Vehicle-id:
•Check for DTC, and if there is any, perform the diagnosis
•Time-out before the operator performed IGN-OFF (60
according to the DTC.
seconds)
(DTC: B2271)
•Operation not reflected due to switch circuit of push button
NG While turning •Check the harness between keyless access CM and push
ignition switch improper connection/malfunction
ignition switch off, button ignition switch, and push button ignition switch alone.
→ "Turn off the ignition switch." •IGN relay stuck ON —
timeout has •Press the push button ignition switch a few times to check that
occurred. •Power supply-output short in harness between keyless
the status changes as OFF → ACC ON → IGN ON.
access CM and IGN relay
•Check the harness between keyless access CM and IGN
•IGN harness power supply-output short
relay.
•Keyless access CM malfunction (control failure)
•Retry "Engine ECM Registration" only.
•Check for DTC, and if there is any, perform the diagnosis
•Time-out before the operator performed IGN-ON (60
according to the DTC.
seconds)
(DTC: B2271)
•Access key not present inside the vehicle
NG While turning •Check if the access key is present inside the vehicle.
•IGN relay stuck OFF
ignition switch on, •Press the push button ignition switch a few times to check that
•GND-output short/open in harness between keyless access —
timeout has the status changes as OFF → ACC ON → IGN ON.
CM and IGN relay
occurred. •Check the harness between keyless access CM and IGN
•IGN harness open/GND-output short
→ "Switch Ignition ON" relay.
•IGN fuse blown out
•Check the upstream fuse of IGN relay.
•Keyless access CM malfunction (control failure)
•Retry "Engine ECM Registration" only.
•After performing IGN OFF once and IGN ON again, retry
"Engine ECM Registration" without opening/closing the
NG cannot •The operator opened or closed the door after IGN-ON
driver’s door. —
Immobilizer unset •Steering lock locked
•While turning the steering wheel, perform IGN ON ←→ OFF
to check that the operation unlocks the steering lock.
NG Number of
When an additional access key needs to be registered, delete
registrations Additional registration impossible —
the registered access key.
98
exceeded
D type
Å`
SIE-id::
Registration history that
Status Screen Trouble mode Action to be taken
possibly remains
Vehicle-id:
•Perform the procedure again according to REGISTRATION
MANUAL FOR IMMOBILIZER.
(Check that the access key to be held is registered to the
vehicle.)
(When either the ID code box or steering lock CM is replaced
•Access key other than registered key was held
with a new part, select "Smart ECM Registration".)
•Access key being held malfunctioning (transponder function)
•Check for DTC, and if there is any, perform the diagnosis
•Time-out before the operator held access key (30 seconds)
according to the DTC.
•Vehicle speed input exceeding 5 km/h (3 MPH)
(DTC: B2789, B2790, B2786, B2785, B278A, B2784) •push-button SW amp error
•Immobilizer amplifier failure
•Check LIN between the keyless access CM and steering lock •Owner key’s check fail
•Access key not held over the push button ignition switch with
CM or ID code box. -hold up non-registration key
the button surface facing yourself
NG Check the owner •Perform harness inspection between the keyless access CM •Failure of the condition
→ "The owner is confirmed" •Access key incorrect item number (incorrect destination/
NG and push button ignition switch, and inspection of the push -LIN communication failure
incorrect system)
button ignition switch alone, and check output of the •Different code between ECM
•Antenna coil malfunction
immobilizer amplifier power supply (VC5) (conduct from Work -Between ID code box
•ECM code incompatibility between keyless access CM and
Support). -Between Steering lock CM
steering lock CM or ID code box (control failure, replacement
•Check that the vehicle speed is normal. (Make sure that the
with used part)
vehicle speed pulse is not output from the direct line.)
•Steering lock CM or ID code box
•Confirm the access key item number and check for
•Keyless access CM, steering lock CM, or ID code box failure
malfunction.
•Check that the data monitor indicates "Normal" for "Code
collation result between keyless access CM and ID code box"
and "Code collation result between steering locked CM and
ID code box".
99
•Perform the procedure according to REGISTRATION
•Time-out before the operator held access key (30 seconds) MANUAL FOR IMMOBILIZER.
D type
[No buzzer sounds, when access key is held] [No buzzer sounds, when access key is held]
•Access key not held over the push button ignition switch with •Confirm the access key item number and check for
the button surface facing yourself malfunction.
•Another (already-collated) access key present near push •Check that the access key is not registered on another
button ignition switch vehicle.
•Access key malfunction (transponder function)
•New key’s check fail
•Access key incorrect item number (incorrect destination/ [Buzzer sounds only once when access key is held, and
NG Time-out -hold up the collated key just
incorrect system) number of registration does not increase]
→ "Register the Access Key." occurred during before
•Access key that was registered on another vehicle was held •Check for DTC, and if there is any, perform the diagnosis
Access Key collation -hold up registered key
according to the DTC.
•Other vehicle key reg
[Buzzer sounds only once when access key is held, and (DTC: B1242, B27A5)
number of registration does not increase] •Check that another access key is not present inside the
•Another access key present inside the vehicle (interference, vehicle.
etc.) •Check that the access key is not registered on another
•Access key that was registered on another vehicle was held vehicle.
•Access key out of battery/malfunction (RF function) •Check the battery of access key.
•RF receiver improper connection/malfunction •Check the access key for malfunction.
•Front indoor antenna improper connection/malfunction •Check the connector wiring/harness of RF receiver.
•Check the front indoor antenna for malfunction.
REGISTRATION MANUAL FOR IMMOBILIZER
S1001BE.fm 100 ページ 2014年4月30日 水曜日 午後2時9分
Å`
SIE-id::
Registration history that
Status Screen Trouble mode Action to be taken
possibly remains
Vehicle-id:
•Check for DTC, and if there is any, perform the diagnosis
NG While Access •Steering lock CM or ID code box improper connection according to the DTC.
Key is registering, •ECM code incompatibility between keyless access CM and (DTC: B2785, B2786, B2789) •Time-out
timeout has steering lock CM or ID code box (control failure) •Check LIN between the keyless access CM and ID code box -no ECM reply mismatch
occurred. •Code writing failure between ECMs or steering lock CM.
•Retry the procedure from the beginning.
•Check for DTC, and if there is any, perform the diagnosis
according to the DTC.
(DTC: B2789, B2790, B2786, B2785, B278A, B2784)
•Check LIN between the keyless access CM and steering lock
CM or ID code box.
•The operator pressed Quit button without registering key
•Check the data link connector and harness. •Failure of the condition
•ECM code incompatibility between keyless access CM and
•Perform harness inspection between the keyless access CM -vehicle speed detection
→ "Access Key is registering..." steering lock CM or ID code box (control failure, replacement
and push button ignition switch, and inspection of the push -diag. communication failure
with used part)
button ignition switch alone, and check output of the -LIN communication failure
[Following failure occurred before none of new registration
NG Failed to immobilizer amplifier power supply (VC5) (conduct from Work •Access key PW difference
access key was collated during new registration key collation
Portable Device Support). •Writing failure
process after registration mode is on.]
Registration •Check that the vehicle speed is normal. (Make sure that the -ECM code (ID code box)
•Vehicle speed input exceeding 5 km/h (3 MPH)
vehicle speed pulse is not output from the direct line.) -ECM code (Steering lock
•Immobilizer amplifier failure
•Check that the data monitor indicates "Normal" for "Code ECM)
•Temporary communication failure with Subaru Select Monitor
collation result between keyless access CM and ID code box" -Keyless access CM
•Steering lock CM or ID code box improper connection
and "Code collation result between steering locked CM and reg info
•Keyless access CM, steering lock CM, or ID code box failure
ID code box".
•Perform the procedure again according to REGISTRATION
MANUAL FOR IMMOBILIZER.
(When either the ID code box or steering lock CM is replaced
with a new part, select "Smart ECM Registration".)
•Check for DTC, and if there is any, perform the diagnosis
•Time-out before the operator performed IGN-OFF (60
according to the DTC.
seconds)
(DTC: B2271)
100
•Operation not reflected due to switch circuit of push button
•Check the harness between keyless access CM and push
D type
Å`
SIE-id::
Registration history that
Status Screen Trouble mode Action to be taken
possibly remains
Vehicle-id:
NG EGI-SSM
Communication Check the communication line between ECM and Subaru
Communication failure with ECM —
(Communication line Select Monitor. (K line or CAN)
judgment)
NG EGI-Immobilizer Communication failure between ECM and keyless access CM
Perform the diagnosis for DTC B1572 (P1572). —
communication or ID code box
(All mode) NG IMM Control
Keyless access CM or ID code box failure Perform the diagnosis for DTC B1577 (P1577). —
"EGI initialization / During Module EEPROM
registration..." NG EGI unit
ECM failure Perform the diagnosis for DTC B1576 (P1576). —
EEPROM
NG EGI security •Subaru Select Monitor failure •Check version of Subaru Select Monitor.
—
access NG •ECM failure •Replace the ECM.
Wait until the self shut completes, and retry the procedure.
NG EGI-SSM
ECM failure When this does not solve the problem, remove and install the —
Communication
battery.
101
D type
REGISTRATION MANUAL FOR IMMOBILIZER
S1001BE.fm 102 ページ 2014年4月30日 水曜日 午後2時9分
Å`
SIE-id::
Registration history that
Status Screen Trouble mode Action to be taken
possibly remains
Vehicle-id:
NG Access Key is
Access key unregistered Execute "Smart Immobilizer Registration". —
not still registered
•Check that the B/up fuse in the M/B or F/B is connected.
•Without ID code box: Check if IDW terminal is not connected
or is grounded.
•With ID code box: Check that IDW terminal is connected to
•B/up fuse disconnected ground.
•Failure of the condition
•ID code box presence judgment circuit failure (harness setting •Check the data monitor of body integrated unit to confirm that
NG Abnormal -vehicle speed detection
failure) the B/up fuse is ON.
Termination -different ID code box setting
•Vehicle speed input exceeding 5 km/h (3 MPH) •Check that the vehicle speed is normal. (Make sure that the
-Among special mode
•Number of keys registered in keyless access CM: zero vehicle speed pulse is not output from the direct line.)
•Check for DTC, and if there is any, perform the diagnosis
according to the DTC.
(DTC : B278D)
•Check if the keyless access CM is replaced with a new part.
•Check the data link connector and harness.
•Perform harness inspection between the keyless access CM
and push button ignition switch, and inspection of the push
button ignition switch alone, and check output of the
immobilizer amplifier power supply (VC5) (conduct from Work
Support).
•Failure of the condition
•Temporary communication failure with Subaru Select Monitor •Check that the vehicle speed is normal. (Make sure that the
-vehicle speed detection
NG Mode transition •Immobilizer amplifier failure vehicle speed pulse is not output from the direct line.)
-Among special mode
error •Vehicle speed input exceeding 5 km/h (3 MPH) •For the vehicle with ID code box, check LIN between keyless
-diag. communication failure
•B/up fuse disconnected access CM and ID code box.
-push-button SW amp error
•Check for DTC, and if there is any, perform the diagnosis
"Smart ECM Registration" start according to the DTC.
(DTC: B2789, B2790, B278A, B2784)
•Check that the B/up fuse in the M/B or F/B is connected. If the
102
part was replaced with a new one, execute "Smart
D type
Immobilizer Registration".
•Perform the procedure again according to REGISTRATION
MANUAL FOR IMMOBILIZER.
(Check that the access key to be held is registered to the
vehicle.)
•Access key other than registered key was held (When either the ID code box or steering lock CM is replaced
•Access key being held malfunctioning (transponder function) with a new part, select "Smart ECM Registration".)
•Time-out before the operator held access key (30 seconds) •Check for DTC, and if there is any, perform the diagnosis •Owner key’s check fail
•Vehicle speed input exceeding 5 km/h (3 MPH) according to the DTC. -hold up non-registration key
•Immobilizer amplifier failure (DTC: B278A, B2784) •Failure of the condition
•Access key not held over the push button ignition switch with •Perform harness inspection between the keyless access CM -vehicle speed detection
the button surface facing yourself and push button ignition switch, and inspection of the push -Among special mode
NG Check the owner
•Access key incorrect item number (incorrect destination/ button ignition switch alone, and check output of the -diag. communication failure
NG
incorrect system) immobilizer amplifier power supply (VC5) (conduct from Work -push-button SW amp error
•Antenna coil malfunction Support). •Different code between ECM
•ECM code incompatibility between keyless access CM and •Check that the vehicle speed is normal. (Make sure that the -Between ID code box
steering lock CM or ID code box (control failure, replacement vehicle speed pulse is not output from the direct line.) -Between Steering lock CM
with used part) •Confirm the access key item number and check for •ECM code registered
•"Smart ECM Registration" executed without replacing the malfunction.
parts •Check that the data monitor indicates "Normal" for "Code
collation result between keyless access CM and ID code box"
and "Code collation result between steering locked CM and
ID code box".
•Check if the necessary part was replaced.
REGISTRATION MANUAL FOR IMMOBILIZER
S1001BE.fm 103 ページ 2014年4月30日 水曜日 午後2時9分
Å`
SIE-id::
Registration history that
Status Screen Trouble mode Action to be taken
possibly remains
Vehicle-id:
•Check for DTC, and if there is any, perform the diagnosis
according to the DTC.
NG Time-out •Steering lock CM or ID code box improper connection (DTC: B2785, B2786, B2789) •Time-out
"Smart ECM Registration" start occurred during
registration •Code writing failure between ECMs •Check LIN between the keyless access CM and steering lock -no ECM reply mismatch
CM or ID code box.
•Retry the procedure from the beginning.
•Check for DTC, and if there is any, perform the diagnosis
according to the DTC.
(DTC: B2271)
•Check if the access key is present inside the vehicle.
•The operator has not performed IGN ON
Not able to confirm •Press the push button ignition switch a few times to check that
•IGN ON impossible (Procedure attempted while keyless —
IG SW ON the status changes as OFF → ACC ON → IGN ON.
access CM unregistered, etc.)
"Engine ECM Registration" start •Check the harness between keyless access CM and IGN
"Please confirm that IG SW becomes relay.
ON" •Check the upstream fuse of IGN relay.
•Retry "Engine ECM Registration" only.
•After performing IGN OFF once and IGN ON again, retry
Because Immobilizer •The door was opened or closed after IGN-ON "Engine ECM Registration" without opening/closing the
is not unset, cannot driver’s door. —
register •Keyless access CM unregistered and IGN ON still possible
•While turning the steering wheel, perform IGN ON ←→ OFF
to check that the operation unlocks the steering lock.
NG EGI-SSM
Communication Check the communication line between ECM and Subaru
Communication failure with ECM —
(Communication line Select Monitor. (K line or CAN)
judgment)
103
NG EGI-Immobilizer Communication failure between ECM and keyless access CM
Perform the diagnosis for DTC B1572 (P1572). —
D type
Å`
SIE-id::
Registration history that
Status Screen Trouble mode Action to be taken
possibly remains
Vehicle-id:
NG Access Key is
Access key unregistered Execute "Smart Immobilizer Registration". —
not still registered
•Check that the B/up fuse in the M/B or F/B is connected.
•Check the data monitor of body integrated unit to confirm that •Failure of the condition
NG Abnormal •B/up fuse disconnected
the B/up fuse is ON. -vehicle speed detection
Termination •Vehicle speed input exceeding 5 km/h (3 MPH)
•Check that the vehicle speed is normal. (Make sure that the -Among special mode
vehicle speed pulse is not output from the direct line.)
•Check the data link connector and harness.
•Perform harness inspection between the keyless access CM
and push button ignition switch, and inspection of the push
button ignition switch alone, and check output of the
•Temporary communication failure with Subaru Select Monitor immobilizer amplifier power supply (VC5) (conduct from Work •Failure of the condition
NG Mode transition
•Immobilizer amplifier failure Support). -vehicle speed detection
error
•Vehicle speed input exceeding 5 km/h (3 MPH) •Check that the vehicle speed is normal. (Make sure that the -diag. communication failure
vehicle speed pulse is not output from the direct line.)
•Check for DTC, and if there is any, perform the diagnosis
according to the DTC.
(DTC: B278A, B2784)
•Perform the procedure again according to REGISTRATION
MANUAL FOR IMMOBILIZER.
(Check that the access key to be held is registered to the
vehicle.)
(When either the ID code box or steering lock CM is replaced
•Access key other than registered key was held
with a new part, select "Smart ECM Registration".)
•Access key being held malfunctioning (transponder function)
•Check for DTC, and if there is any, perform the diagnosis
•Time-out before the operator held access key (30 seconds)
"Delete the Access Key ID" start according to the DTC.
•Vehicle speed input exceeding 5 km/h (3 MPH)
(DTC: B2789, B2790, B2786, B2785, B278A, B2784) •push-button SW amp error
104
•Immobilizer amplifier failure
•Check LIN between the keyless access CM and steering lock •Owner key’s check fail
D type
•Access key not held over the push button ignition switch with
CM or ID code box. -hold up non-registration key
the button surface facing yourself
NG Check the owner •Perform harness inspection between the keyless access CM •Failure of the condition
•Access key incorrect item number (incorrect destination/
NG and push button ignition switch, and inspection of the push -LIN communication failure
incorrect system)
button ignition switch alone, and check output of the •Different code between ECM
•Antenna coil malfunction
immobilizer amplifier power supply (VC5) (conduct from Work -Between ID code box
•ECM code incompatibility between keyless access CM and
Support). -Between Steering lock CM
steering lock CM or ID code box (control failure, replacement
•Check that the vehicle speed is normal. (Make sure that the
with used part)
vehicle speed pulse is not output from the direct line.)
•Steering lock CM or ID code box improper connection
•Confirm the access key item number and check for
•Keyless access CM, steering lock CM, or ID code box failure
malfunction.
•Check that the data monitor indicates "Normal" for "Code
collation result between keyless access CM and ID code box"
and "Code collation result between steering locked CM and
ID code box".
•Failure of the condition
•Check for DTC, and if there is any, perform the diagnosis
-LIN communication failure
according to the DTC.
•Writing failure
•ECM code incompatibility between keyless access CM and (DTC: B2785, B2786, B2789)
-ECM code (ID code box)
steering lock CM or ID code box (control failure, replacement •Check LIN between the keyless access CM and steering lock
NG Access Key ID -ECM code (Steering lock
with used part) CM or ID code box.
Deletion Mode NG ECM)
•Steering lock CM or ID code box improper connection •Perform the procedure again according to REGISTRATION
-Keyless access CM
•Code writing failure between ECMs MANUAL FOR IMMOBILIZER.
reg info
(When either the ID code box or steering lock CM is replaced
•Time-out
with a new part, select "Smart ECM Registration".)
-no ECM reply mismatch
REGISTRATION MANUAL FOR IMMOBILIZER
S1001BE.fm 105 ページ 2014年4月30日 水曜日 午後2時9分
Å`
SIE-id::
<List of DTC codes, when the immobilizer is not registered>
Vehicle-id:
<When keyless access CM is replaced> B1572 (P1572) Imm Circuit Failure (Except Antenna Circuit)
<When ECM is replaced> B1571 (P1571) Reference Code Incompatibility
105
D type
REGISTRATION MANUAL FOR IMMOBILIZER
S1001BE.fm 106 ページ 2014年4月30日 水曜日 午後2時9分
Å`
SIE-id::
7-12 List of registration history
Vehicle-id:
Job contents
SSM display Access key Keyless Registering Cause of failure Action to be taken
Access key
additional access CM the Smart
ID deletion
registration replacement ECM
•Registration was attempted for an access key for a
Access key PW different vehicle. Check that the access key shape and item number are correct for the
— O O
difference •Registration was attempted for an access key for a vehicle to register, and then perform the registration.
different brand.
•Time-out occurred while registration was attempted for
an access key that was registered on another vehicle.
•Time-out occurred while registration was attempted for Check that the access key to be registered is an unregistered new
hold up the collated key the access key that was registered to the vehicle to be part, and then perform the registration.
New key’s check fail just before O O * After registration, if number of access keys indicated in "Readout the
hold up registered key worked on. number of Access Key registration" is the desired number, registration
•Time-out occurred while registration was attempted is completed correctly and is normal.
again for the access key that had been held to register
before.
1. Check that the access key is registered to the vehicle to be worked
•The access key that was new or registered on another
on, and then perform the registration.
vehicle was held over the push button ignition switch.
hold up non-registration 2. Check that the keyless access CM is not replaced with a part
O O O •Registration was attempted after the keyless access
key registered on another vehicle, and then perform the registration.
CM was wrongly replaced with a part registered on
3. When all the access keys that are registered to the vehicle to be
another vehicle.
Owner key’s check fail worked on are not found, contact your Subaru service representative.
After registration, if number of access keys indicated in "Readout the
number of Access Key registration" is the demanded number,
Time-out occurred while registration was attempted
hold up the collated key registration is completed correctly and is normal. If registration
O again for the access key that had been held to register
106
just before completed before registering a desired access key, such an
before.
D type
Å`
SIE-id::
Job contents
Vehicle-id:
SSM display Access key Keyless Registering Cause of failure Action to be taken
Access key
additional access CM the Smart
ID deletion
registration replacement ECM
1. Check that all the access keys to be held are registered to the
vehicle to be worked on, and then perform registration.
2. When key registration is possible with the keyless access CM that
When checking all the access keys that were registered was previously installed, return that keyless access CM back. Then,
to the vehicle to be worked on, a new access key or after executing "Access key ID deletion" until only one key remains as
O
access key that was registered on another vehicle was registered, replace the keyless access CM, and perform the
included. registration.
3. When key registration is not possible with the keyless access CM
that was previously installed, contact your Subaru service
representative.
Between ID code box
1. Check that the ID code box and steering lock CM were not
* Models with ID code Before registration, the ID code box and steering lock
registered on another vehicle, and then perform the registration.
box only O O O O CM were wrongly replaced as a set with parts that were
2. In the case of the key registered on another vehicle, contact your
registered on another vehicle.
Subaru service representative.
1. Check that the access key and keyless access CM were not
Before registration, the access key and keyless access
registered on another vehicle, and then perform the registration.
O O O O CM were wrongly replaced as a set with parts that were
2. In the case of the key registered on another vehicle, contact your
registered on another vehicle.
Subaru service representative.
1. Check that the ID code box was not replaced with a new part, and
Different code between
Before registration, the ID code box was wrongly then perform registration.
ECM O
replaced with a new part. 2. Execute "Smart ECM Registration", and then perform desired
registration.
When checking all the access keys that were registered 1. Check that all the access keys to be held are registered to the
to the vehicle to be worked on, a new access key or vehicle to be worked on, and then perform the registration.
O access key that was registered on another vehicle was 2. In the case of the key registered on another vehicle, contact your
107
included. Subaru service representative.
D type
Å`
SIE-id::
Job contents
Vehicle-id:
SSM display Access key Keyless Registering Cause of failure Action to be taken
Access key
additional access CM the Smart
ID deletion
registration replacement ECM
[Vehicle with ID code box]
Registration was performed without the IDW terminal of
different ID code box keyless access CM connected to GND.
O Contact your Subaru service representative.
setting [Vehicle without ID code box]
Registration was performed with the IDW terminal of
keyless access CM connected to GND.
push-button SW amp The immobilizer power supply circuit of push button Check the harness between keyless access CM and push button
O O O O
error ignition switch is shorted to ground. ignition switch.
1. Perform registration with the vehicle at standstill.
Registration was performed while vehicle speed of 5
vehicle speed detection O O O O 2. Check the vehicle speed pulse output from VDC to confirm that the
km/h or more was detected.
vehicle speed is normally output, and then perform registration.
Failure of the condition Registration was performed while LIN communication
LIN communication Perform the diagnosis for "DTC B2785 LIN COMMUNICATION
O O O O failure was detected between keyless access CM — ID
failure ERROR", and then perform registration.
code box — steering lock CM.
1. Perform the diagnosis for "COMMUNICATION FOR INITIALIZING
Registration was performed, while communication IMPOSSIBLE", and then perform registration.
diag. communication
O O O O between Subaru Select Monitor and keyless access CM 2. Perform the diagnosis if "DTC U0073 CONTROL MODULE
failure
was not established. COMMUNICATION BUS "A" OFF" is detected, and then perform
registration.
•B/up fuse in M/B or F/B is disconnected or blown out. Check "B/up" on the data monitor of body integrated unit to check that
the value is 9 V or more. When the displayed voltage is low, check the
Among special mode O O O O •Body integrated unit cannot detect B/up status
B/up fuse of M/B and F/B, and harness to body integrated unit, and
correctly. then perform registration.
ID code box data writing failed due to temporary poor
From the diagnosis for "DTC B2785 LIN COMMUNICATION ERROR",
ECM code (ID code connection of LIN communication circuit during
O O O O perform the harness and connector inspection, and then perform
108
box) registration.
registration.
D type
D type
REGISTRATION MANUAL FOR IMMOBILIZER
IM-00639
109
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 110 ページ 2014年4月30日 水曜日 午後2時9分
E type
REGISTRATION MANUAL FOR IMMOBILIZER
8 E type C: Caution
Vehicle without keyless access with push button • When you install wireless radios or car
start system, without security ID (security tag) phones, make sure that the immobilizer
when the vehicle is new, and with immobilizer CM. system is not influenced by their electric
Note: waves.
U.K./CANADA • Do not operate cell phones or wireless radios
A: Structure or the like when either trouble diagnosis or
An immobilizer system consists of the following immobilizer registration is in progress.
components: Immobilizer indicator (in combination • During immobilizer registration, do not bring
meter), ECM, ignition key, immobilizer antenna, a key with a different ID close to the ignition
and immobilizer CM. switch. When the key is on a keychain,
B: Operation remove it from the chain before start of
When the ignition key with built-in transponder is diagnosis. When there are several keys on
inserted in the key cylinder, the immobilizer CM one keychain, remove them from the
receives ignition key ID via the immobilizer keychain and use them individually for the
antenna. work.
The received key ID is collated with the key ID • When the engine cannot be started with a
stored in the memory of immobilizer CM. registered key, pull the ignition key from the
Then, the engine IDs stored in the memory of the ignition switch, wait approximately one
ECM and immobilizer CM are collated. second until the immobilizer warning lamp
If the IDs do not match within the specified period of starts flashing, and then turn the ignition key
time after the RPM of the engine reaches the
slowly to start the engine.
specified RPM, the engine stops.
If the IDs do not match, the engine stops within a • Confirm that the battery voltage is 11 V or
couple of seconds. If the engine does not start as a more and execute each mode.
result of a mismatch of the IDs, the immobilizer • During immobilizer registration, make sure
indicator in the combination meter turns on to connectors do not get disconnected.
indicate that the immobilizer is active. When the Note:
ignition key is removed, the immobilizer is activated When performing either one of the operations
and the immobilizer indicator lamp flashes to shown below, perform also the "Registering
generate an alert notifying people around the Remote Control Engine Starter".
vehicle that it is protected by the immobilizer.
• Installing remote control engine starter
• Replacing remote control engine starter
• Replacing immobilizer CM of the vehicle with
remote control engine starter
110
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 111 ページ 2014年4月30日 水曜日 午後2時9分
E type
REGISTRATION MANUAL FOR IMMOBILIZER
8-1 Registering Immobilizer CM 4) Click the [YES] button if the System Check
screen is displayed.
Caution:
Only when the immobilizer CM was replaced.
1) Start the PC application according to section
"Starting Up the System" and display the Main
Menu screen. Using the key you want to IM-00404
register, turn on the ignition switch. (Refer to
"PC application help for Subaru Select
Monitor".)
2) On the Main Menu, select [All other models].
IM-00404
Note:
Audio System is the specification only for the U.K.
5) On the next screen, confirm the system is
keyless access with push button start system.
Click the [NO] button.
IM-00491
IM-00405
Note:
The term [smart system] that appears on this
screen is synonymous with the term [keyless
access with push button start system] used in this
IM-00492 text.
6) Click [YES] after confirming if the ignition switch
is ON, as following screen will be displayed.
Note:
When an error screen is displayed, refer to No. 1 in
"8-7 Correspondence table when registration is not
possible".
IM-00406
IM-00406
111
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 112 ページ 2014年4月30日 水曜日 午後2時9分
E type
REGISTRATION MANUAL FOR IMMOBILIZER
IM-00605
IM-00621 IM-00606
9) Registration content appears. Confirm that the 12) The screen shown below will appear if
ignition is turned ON using the key you want to registration ends normally. If you have another
register, and click the [OK] button. keys to be registered, insert the next key into
Note: the ignition switch, turn on the ignition key, and
When an error screen is displayed, refer to No. 2 return to step 11. If you have no more keys to
and 3 in "8-7 Correspondence table when be registered, click the [Exit] button.
registration is not possible". Note:
When an error screen is displayed, refer to No. 3
and 4 in "8-7 Correspondence table when
registration is not possible".
IM-00604
112
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 113 ページ 2014年4月30日 水曜日 午後2時9分
E type
REGISTRATION MANUAL FOR IMMOBILIZER
IM-00611
17) Make sure the engine can be started with all the
registered keys, then quit the registration
procedure.
IM-00608
IM-00609
IM-00610
Note:
a = Number of registered key
113
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 114 ページ 2014年4月30日 水曜日 午後2時9分
E type
REGISTRATION MANUAL FOR IMMOBILIZER
8-2 Adding Keys 4) Click the [YES] button if the System Check
screen is displayed.
Caution:
To add keys, you need one registered key.
IM-00405
IM-00491
IM-00405
IM-00406
IM-00406
114
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 115 ページ 2014年4月30日 水曜日 午後2時9分
E type
REGISTRATION MANUAL FOR IMMOBILIZER
IM-00605
ࠠᾖวਛ̖
IM-00621
IM-00612
⚳ੌ
Note:
n = Number of registered key
IM-00614
10) Stand by as the communication initialization is
performed. 13) Stand by as the key is registered.
115
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 116 ページ 2014年4月30日 水曜日 午後2時9分
E type
REGISTRATION MANUAL FOR IMMOBILIZER
IM-00610
IM-00606
Note:
14) The screen shown below will appear if a = Number of registered key
registration ends normally. If you have another 17) The screen shown below will appear if
keys to be registered, insert the next key into registration ends normally. Remove the key and
the ignition switch, turn on the ignition key, and click the [OK] button.
return to step 13. If you have no more keys to
be registered, click the [Exit] button.
Note:
When an error screen is displayed, refer to No. 3 in
"8-7 Correspondence table when registration is not
possible".
IM-00611
18) Make sure the engine can be started with all the
registered keys, then quit the registration
procedure.
IM-00607
Note:
a = Number of registered key
15) Stand by as the key registration ends.
IM-00608
116
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 117 ページ 2014年4月30日 水曜日 午後2時9分
E type
REGISTRATION MANUAL FOR IMMOBILIZER
8-3 Registering Engine ECM 4) Click the [YES] button if the System Check
screen is displayed.
Caution:
To add keys, you need one registered key.
1) Start the PC application according to section
"Starting Up the System" and display the Main
Menu screen. Using the registered key, turn on
the ignition switch. (Refer to "PC application
help for Subaru Select Monitor".)
Caution:
Make sure to use a registered key.
IM-00404
2) On the Main Menu, select [All other models].
Note:
Audio System is the specification only for the U.K.
5) On the next screen, confirm the system is
keyless access with push button start system.
Click the [NO] button.
IM-00491 IM-00405
3) Select [Immobilizer] from the item selection
dialog box.
IM-00405
IM-00406
IM-00406
117
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 118 ページ 2014年4月30日 水曜日 午後2時9分
E type
REGISTRATION MANUAL FOR IMMOBILIZER
7) On the Main Menu that appears on the display, 10) Stand by as the communication initialization is
select [Engine ECU registration]. performed.
Note: Note:
If the command input screen is displayed instead of When an error screen is displayed, refer to No. 7
the menu screen, the vehicle is A type. See the and 8 in "8-7 Correspondence table when
procedures for A type vehicle. registration is not possible".
IM-00615 IM-00605
IM-00609
IM-00620
12) The screen shown below will appear if
9) Confirm that the ignition is turned ON using the registration ends normally. Click the [OK]
registered key, and click the [OK] button. button.
Note:
When an error screen is displayed, refer to No. 2, 6,
7 and 8 in "8-7 Correspondence table when
registration is not possible".
IM-00617
118
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 119 ページ 2014年4月30日 水曜日 午後2時9分
E type
REGISTRATION MANUAL FOR IMMOBILIZER
13) The screen shown below will appear if 8-4 Registering Remote Control
registration ends normally. Remove the key and Engine Starter
click the [OK] button.
Caution:
To add keys, you need one registered key.
1) Start the PC application according to section
"Starting Up the System" and display the Main
Menu screen. Using the registered key, turn on
the ignition switch. (Refer to "PC application
help for Subaru Select Monitor".)
Caution:
Make sure to use a registered key.
IM-00618
2) On the Main Menu, select [All other models].
14) Make sure the engine can be started with all the
registered keys, then quit the registration
procedure.
IM-00491
IM-00492
119
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 120 ページ 2014年4月30日 水曜日 午後2時9分
E type
REGISTRATION MANUAL FOR IMMOBILIZER
4) Click the [YES] button if the System Check 7) On the Main Menu that appears on the display,
screen is displayed. select [Remote Control Engine Starter
Registration].
Note:
If the command input screen is displayed instead of
the menu screen, the vehicle is A type. See the
IM-00404
procedures for A type vehicle.
IM-00404
Note:
Audio System is the specification only for the U.K.
5) On the next screen, confirm the system is
keyless access with push button start system. IM-00615
Click the [NO] button.
8) On the registration mode confirmation dialog
box that appears, click the [OK] button.
Note:
When an error screen is displayed, refer to No. 12
IM-00405 in "8-7 Correspondence table when registration is
not possible".
IM-00405
IM-00406
120
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 121 ページ 2014年4月30日 水曜日 午後2時9分
E type
REGISTRATION MANUAL FOR IMMOBILIZER
IM-00491
IM-00492
IM-00623
121
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 122 ページ 2014年4月30日 水曜日 午後2時9分
E type
REGISTRATION MANUAL FOR IMMOBILIZER
4) Click the [YES] button if the System Check 7) On the Main Menu that appears on the display,
screen is displayed. select [Immobilizer Key ID deletion].
Note:
If the command input screen is displayed instead of
the menu screen, the vehicle is A type. See the
IM-00404 procedures for A type vehicle.
IM-00404
Note:
Audio System is the specification only for the U.K.
5) On the next screen, confirm the system is
IM-00615
keyless access with push button start system.
Click the [NO] button. 8) The deletion mode confirmation dialog box
appears. Click the [OK] button.
Note:
When an error screen is displayed, refer to No. 9 in
IM-00405 "8-7 Correspondence table when registration is not
possible".
IM-00405 ࠗࡕࡆࠗࠩࠠIDᶖࠍታⴕߒ߹ߔ߆㧫
IM-00406
122
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 123 ページ 2014年4月30日 水曜日 午後2時9分
E type
REGISTRATION MANUAL FOR IMMOBILIZER
IM-00605
IM-00625
Note:
a = Number of registered key
12) The screen shown below will appear if deletion
ends normally. Remove the key, and click the
[OK] button.
IM-00626
123
Vehicle-id:
SIE-id::
Å`
S1001BE.fm 124 ページ 2014年4月30日 水曜日 午後2時9分
Å`
SIE-id::
8-6 Immobilizer system (when Immobilizer CU (U.K./CANADA)) : Correspondence table at the time of
Vehicle-id:
parts lost or failure
If all the keys are lost, for protection against vehicle theft you must contact your Subaru service representative.
Caution:
When replacing the parts, always use a new one. Used parts cannot be registered.
124
E type
Å`
SIE-id::
8-7 Correspondence table when registration is not possible
Vehicle-id:
A list of possible trouble mode, when an error screen is displayed at each status (procedure).
No. Status (procedure) Error screen Trouble mode Action to be taken
•CAN communication failure between Subaru Select Monitor and
Select "Immobilizer" from the Main NG Comm. Failed immobilizer CM
Menu •CAN communication failure between Subaru Select Monitor and Perform the diagnosis for LAN system.
1 → System "Immobilizer" → Smart body integrated unit
System "NO" → IGN-ON "YES" → CAN communication failure between Subaru Select Monitor and
Meter/SCU registration immobilizer CM
Perform the diagnosis for LAN system.
NG Abnormal Termination •Subaru Select Monitor malfunction Check version of Subaru Select Monitor.
•Immobilizer CM malfunction Replace the immobilizer CM.
NG Cannot judge register mode (new Check version of Subaru Select Monitor.
Immobilizer CM malfunction
or add) Replace the immobilizer CM.
NG Transponder communication
Transponder failure Check DTC and perform the diagnosis.
failure.
NG Immobilizer antenna failure. Antenna failure Check DTC and perform the diagnosis.
NG Non-volatile memory failure. Immobilizer CM failure Check DTC and perform the diagnosis.
3 → "Initializing communication..."
NG Performed conditions not
IGN-OFF performed during registration mode Perform re-registration.
established.
•NG key Check DTC and perform the diagnosis.
NG Transponder collation failure.
•Unregistered key Prepare the registered key.
NG Registration was not When multiple attempts of registration did not solve the problem,
Immobilizer CM malfunction
successfully. replace the immobilizer CM.
CAN communication failure between Subaru Select Monitor and
NG BIU-SSM Communication Perform the diagnosis for LAN system.
immobilizer CM
125
→ "EGI initialization / During NG EGI-SSM Communication Check the communication line between ECM and Subaru Select
E type
NG BIU-SSM Communication CAN communication failure between Subaru Select Monitor and
Perform the diagnosis for LAN system.
immobilizer CM
REGISTRATION MANUAL FOR IMMOBILIZER
S1001BE.fm 126 ページ 2014年4月30日 水曜日 午後2時9分
Å`
SIE-id::
No. Status (procedure) Error screen Trouble mode Action to be taken
Vehicle-id:
NG EGI-SSM Communication Check the communication line between ECM and Subaru Select
Communication failure with ECM
(Communication line judgment) Monitor. (K line or CAN communication line)
•IGN-OFF performed during registration mode Retry the procedure.
NG EGI-Immobilizer communication •Communication failure between ECM and immobilizer CM Perform the diagnosis for DTC B1572 (P1572).
NG IMM Control Module EEPROM Immobilizer CM failure Perform the diagnosis for DTC B1577 (P1577).
→ "EGI initialization / During NG EGI unit EEPROM ECM failure Perform the diagnosis for DTC B1576 (P1576).
8 registration..."
NG EGI security access NG •Subaru Select Monitor failure Check version of Subaru Select Monitor.
•ECM failure Replace the ECM.
Wait until the self shut completes, and retry the procedure.
•ECM failure When the same error is indicated again, remove and install the
NG EGI-SSM Communication battery.
•Communication failure between Subaru Select Monitor and ECM Check the communication line between ECM and Subaru Select
Monitor. (K line or CAN communication line)
Registered number = 0 Immobilizer CM unregistered Execute "Immobilizer system registration" to register the key.
9 "Immobilizer key ID deletion" start
Registered number = 1 - —
10 → "Turn ON the ignition switch." Cannot confirm ignition ON. IGN line of immobilizer CM not detected Check the data monitor. → Check the communication line.
Subaru Select Monitor malfunction Check version of Subaru Select Monitor.
NG Abnormal Termination
Immobilizer CM malfunction Replace the immobilizer CM.
NG Transponder communication
Transponder failure Check DTC and perform the diagnosis.
failure.
NG Immobilizer antenna failure. Antenna failure Check DTC and perform the diagnosis.
126
CAN communication failure between Subaru Select Monitor and
NG BIU-SSM Communication Perform the diagnosis for LAN system.
E type
immobilizer CM
"Remote Control Engine Starter
12 Registered number = 0 Immobilizer CM unregistered Execute "Immobilizer system registration" to register the key.
Registration" start
13 → "Turn ON the ignition switch." Cannot confirm ignition ON. IGN line of immobilizer CM not detected Check the data monitor. → Check the communication line.
NG Abnormal Termination •Subaru Select Monitor malfunction Check version of Subaru Select Monitor.
•Immobilizer CM malfunction Replace the immobilizer CM.
NG Transponder communication
Transponder failure Check DTC and perform the diagnosis.
failure.
NG Immobilizer antenna failure. Antenna failure Check DTC and perform the diagnosis.
•NG key
NG Transponder collation failure. Prepare the registered key.
•Unregistered key
14 → "Initializing communication..." NG Performed conditions not IGN-OFF performed during registration mode —
established.
NG Remote Control Engine Starter CAN communication failure between immobilizer CM and remote
Perform the diagnosis for LAN system.
communication failure. control engine starter
Perform the diagnosis for the remote control engine starter, and
•Remote control engine starter malfunction
NG Remote start registration NG immobilizer CM.
•Immobilizer CM malfunction
When the same error is indicated again, replace the immobilizer CM.
CAN communication failure between Subaru Select Monitor and
NG BIU-SSM Communication Perform the diagnosis for LAN system.
immobilizer CM
REGISTRATION MANUAL FOR IMMOBILIZER
S1001BE.fm 127 ページ 2014年4月30日 水曜日 午後2時9分
Å`
SIE-id::
List of DTC codes, when the immobilizer is not registered
Vehicle-id:
B1402 Immobilizer Key Collation NG
<When immobilizer CM is replaced> B1571 (P1571) Reference Code Incompatibility
B1575 (P0513) Incorrect Immobilizer Key
B1402 Immobilizer Key Collation NG
<When unregistered key is used>
B1575 (P0513) Incorrect Immobilizer Key
<When ECM is replaced> B1571 (P1571) Reference Code Incompatibility
127
E type
REGISTRATION MANUAL FOR IMMOBILIZER
S1001BE.fm 128 ページ 2014年4月30日 水曜日 午後2時9分
E type
REGISTRATION MANUAL FOR IMMOBILIZER
IM-00639
128
Vehicle-id:
SIE-id::
Å`