Professional Documents
Culture Documents
SW70X1(P) SW70X2(P)
SW75X1S(P) SW75X2S(P)
1. Precautions
2. Specifications
3. Features
4. Operating Instructions
FU
LLY
AUT
OM
AT
IC
W
AS
HIN
G
MAC
HINE
CO
LD
HO HIGH
T
MEDIU
7. Troubleshooting
8. Exploded Views
9. Power Cord
1. Precautions
When performing trouble - shooting and part replacement during servicing note the following safety precautions.
Classifications Specifications
Washing and Dehydrating Capacity 5.0 kg / 5.5 kg
Washing Method Heavy duty rotation type (centripetal current)
Standard Volume of Water High Level 50 l
Medium Level 43 l
Low Level 35 l
Extra low level 28 l
Applicable Volume of Water 145 l (high level of water)
Rotation of the Pulsator 126 rpm
Rotation of the Spin Tub 760 rpm
Power Consumption Washing 310 W
Spinning 240 W
Dehydration Method Centrifugal dehydration type
Drain Control Motor driven
Applicable Water Pressure 0.05~0.78Mpa (0.5 kgf / cm2 ~ 8.0 kgf / cm2)
Weight Gross 34kg
Net 31kg
Dimension Gross W 580mm x D 620mm x H 890mm
Net W 540mm x D 560mm x H 850mm
Accessories Water supply hose, drain hose, owner's manual
540
345
1160
1010
850 850
30
3-2 Installation
3-2-1 Level Specifications and Wall - Clearance 3-2-3 Controlling the Front Adjustable Leg
Distances To control the height, turn the adjustable leg.
1. Install the washing machine on a solid and level
floor.
2. Place the machine at least 40cm away from the wall.
3. Placement on an inclined, weak or rough floor may
cause abnormal trembling.
F U LL
Y AUT
OMATI
C WAS HIN
G MAC
HINE
COLD
HOT
WATER SUPPLY
HIGH
MEDIUM
LOW
EXTRA LOW
WATER LEVEL
FUZZY
SOAK
WOOL
SPEEDY
COURSE
WASH
RINSE
SPIN
FUNCTION
REMAINING TIME
DELAY START
MIN
H START/HOLD
POWER
COLD
(b)
HOT HIGH
MEDIU
WATE LOW M FUZZY
R SUPP
EXTRA SOAK
LY LOW WASH
WATE WOOL
REMAIN
R LEVEL SPEED RINSE ING
Y TIME
COUR SPIN
SE MIN
FUNCT
ION H
START/HOL
DELAY D
START POWER
1. Romove the adaptor from the 2. First, using a "+" type screwdriver, 3. Connect adaptor to the water tap
water supply hose. loosen the three screws on the by firmly tightening the screws.
adaptor. Then turn part (b), following the
Next, take the adaptor and hold arrow, and put (a) and (b) toge-
parts (a) and (b) with a gap about ther.
5mm between them.
a
a
b
b
4. Connect the water supply hose 5. Connect the other end of the If the water tap is a screw type,
to the adaptor. Pull down part (c) water supply hose to the inlet connect a water supply hose that
of the water supply hose. When water valve at the back of the fits to the tap as shown.
part (c) is released, the hose is washer.
automatically connected to the Screw the hose clockwise, all the
adaptor, and makes a 'click' way in.
sound.
3m
Do not put the end of the drain Do not place the hose below the
hose into the water. floor level of the drain outlet.
DRAIN HOSE
(Pump)
DOUBLE FALL
GUIDE
POWER CORD
BLEACH INLET
SOUND ABSORPTION
SPIN BASKET PANEL
LINT FILTER
MAGIC HAND
PULSATOR
FRONT
CONTROL PANEL GROUND LEAD
4
1 2 3
F UL L
Y AU
T OMA
T IC W
AS HIN COLD HIGH FUZZY REMAINING TIME
G MAC H
IN E WASH
MEDIUM SOAK MIN
HOT LOW RINSE POWER
WOOL H START/HOLD
EXTRA LOW SPIN
SPEEDY
WATER SUPP
LY WATER LEVEL
COURSE FUNCTION DELAY START
5 8 9
6 7
4-2-7 Course
4-2-4 Power
1. Press this button to select the type of washing cycle.
1. Press this button for power ON/OFF.
2. When the washing operation is completed, the
4-2-8 Function
power automatically turns off and the buzzer
1. The selection order is :
sounds off 5 times.
Fuzzy → Soak → Wool → Speedy
3. Allow at least a 3-second interval before turning the
washing machine again .
4-2-9 Delay Start
1. This function is to finish the washing operation at
the time user set.
2. You may change the delay start time by using this
button. (from 3 hours to 12 hours)
4-3-4 Function Button 3. The display shows the remaining time, including the current
function, when in 'start' status.
1. This key is valid except for weight sensing operation. The time decreases 1-min at a time.
2. After START/HOLD during operation or under reset When in 'Hold' status, the time stays as it is.
condition, as pressing this key display is changing as
follows.
4-3-7 Power
→WASH →RINSE →SPIN →WASH + RINSE
1) This key is always available when the power cord is
→ RINSE + SPIN →WASH→RINSE + SPIN connected.
2) sequence : → ON → OFF → ON
3. The beginning conditions are as follows when function key
is selected. 3) After finishing operation, this key is automatically turned
off.
1. Weight recognizing function works first washing 3. If the water level does not reach to the water level
operating before water is supplied, not in WOOL selected for 60minutes after starting water
course and Manual function operation (Wash, supplying, the water supplying Error is displaying
Rinse, Spin, •••) on the display.
Hot / Cold Hot / Cold Hot / Cold Hot / Cold Hot / Cold 4-4-4 Fuzzy Function
4-5
WASH RINSE 2 RINSE 1 SPIN TOTAL
TIME
WATER
FREQUENCY COURSE WATER INTER- WATER INTER- WATER INTER-
LEVEL SOAK WASH DRAIN SPIN STOP RINSE DRAIN SPIN STOP RINSE DRAIN SPIN STOP MIN
SUPPLY MITTENT SUPPLY MITTENT SUPPLY MITTENT
50Hz FUZZY HIGH 3' 20' 1'30" 1' 1'30" 1' 3' 2' 1'30" 1' 1'30" 1' 3' 2' 1'30" 1' 5' 1' 51'30"
/
60Hz MEDIUM 2'30" 20' 1'15" 1' 1'30" 1' 2'30" 2' 1'15" 1' 1'30" 1' 2'30" 2' 1'15" 1' 5' 1' 49'15"
LOW 2' 20' 1' 1' 1'30" 1' 2' 2' 1' 1' 1'30" 1' 2' 2' 1' 1' 4' 1' 46'
EXTRA LOW 1'30" 20' 45" 1' 1'30" 1' 1'30" 2' 45" 1' 1'30" 1' 1'30" 2' 45" 1' 4' 1' 43'45"
SOAK HIGH 3' 30' 20' 1'30" 1' 1'30" 1' 3' 2' 1'30" 1' 1'30" 1' 3' 2' 1'30" 1' 5' 1' 81'30"
MEDIUM 2'30" 30' 20' 1'15" 1' 1'30" 1' 2'30" 2' 1'15" 1' 1'30" 1' 2'30" 2' 1'15" 1' 5' 1' 79'15"
LOW 2' 30' 20' 1' 1' 1'30" 1' 2' 2' 1' 1' 1'30" 1' 2' 2' 1' 1' 4' 1' 76'
EXTRA LOW 1'30" 30' 20' 45" 1' 1'30" 1' 1'30" 2' 45" 1' 1'30" 1' 1'30" 2' 45" 1' 4' 1' 73'45"
WOOL HIGH 3' 10' 1'30" 1' 1' 1' 3' 2' 1'30" 1' 1' 1' 3' 2' 1'30" 1' 1' 1' 36'30"
SPEEDY HIGH 3' 8' 1'30" 1' 1' 1' 3' 2' 1'30" 1' 1' 1' 3' 2' 1'30" 1' 5' 1' 38'30"
MEDIUM 2'30" 8' 1'15" 1' 1' 1' 2'30" 2' 1'15" 1' 1' 1' 2'30" 2' 1'15" 1' 5' 1' 36'15"
LOW 2' 8' 1' 1' 1' 1' 2' 2' 1' 1' 1' 1' 2' 2' 1' 1' 4' 1' 33'00"
EXTRA LOW 1'30" 8' 45" 1' 1' 1' 1'30" 2' 45" 1' 1' 1' 1'30" 2' 45" 1' 4' 1' 30'45"
LOW 2' 2' 1' 1' 1'30" 1' 2' 2' 1' 1' 4' 1' 19'30"
EXTRA LOW 1'30" 2' 45" 1' 1'30" 1' 1'30" 2' 45" 1' 4' 1' 18'
WASH HIGH 3'00" 20' 1'30" 1' 1'30" 1' 3' 2' 1'30" 1' 1'30" 1' 3' 2' 1'30" 1' 5' 1' 51'30"
RINSE MEDIUM 2'30" 20' 1'15" 1' 1'30" 1' 2'30" 2' 1'15" 1' 1'30" 1' 2'30" 2' 1'15" 1' 5' 1' 49'15"
SPIN LOW 2' 20' 1' 1' 1'30" 1' 2' 2' 1' 1' 1'30" 1' 2' 2' 1' 1' 4' 1' 46'
EXTRA LOW 1'30" 20' 45" 1' 1'30" 1' 1'30" 2' 45" 1' 1'30" 1' 1'30" 2' 45" 1' 4' 1' 43'45"
4-6
F UL
LY
AUT
OMA
TIC
WAS
HI
NG
MACHI
NE
COLD
HOT HIGH
MEDIUM
WATER LOW FUZZY
SUPPLY EXTRA SOAK
LOW WASH
WATER WOOL
REMAININ
LEVEL SPEEDY RINSE
G TIME
COURS SPIN
MIN
E
FUNCTIO
H
N START/HOLD
DELAY
START POWER
Shape
6-2 Disassembly
1) Remove two Screws fixing the Top-Cover and the Cover T.C.
2) Lift up the Cover TC while pushing it in the direction of the arrow. PUSHING
◗ Pressure Sensor
1) Pull out the Lead Wire Terminal of the Pressure Sensor.
2) Remove the Pressure Sensor.
3) Pull out the Air Hose.
◗ Water Valve
1) Pull out the Lead Wire Terminals.
2) Remove the Screws which fix the detergent box to the top-cover.
◗ Checker
1) Pull out the Lead Wire Terminals.
2) Remove the two Screws.
3) Lift out the Checker.
◗ Wire Harness
1) Pull out the Lead Wire Terminals from the PCB.
2) Pull out the Lead Wire Terminals from the parts in back of the
Top Cover.
3) Remove the Wire Harness.
◗ Transformer
1) Pull out the Lead Wire Terminals.
2) Remove the Screw.
3) Remove the Transformer.
1) Lay down the Washing Machine with the rear side facing the
floor.
2) Pull out the Lead Wire Terminal.
3) Remove the Bolt.
4) Remove the Drain Motor Wire from the Link.
5) Lift out the Drain Motor
1) Remove the four Screws fixing the Top Cover, and lift up the Top
Cover gently tilt the Top Cover back to expose the Tub Cover.
2) Remove the four Screws fixing the Tub Cover.
3) Remove the Bolt fixing the Pulsator.
4) Remove the Spin Nut fixing the flange Shaft and the Shaft and
pull out the Spin Basket.
Caution
¥ Disassemble the Spin Nut in a counterclockwise direction.
5) Lay down the Washing Machine with the rear side facing the
floor.
6) Remove the two Bolts fixing the Saddle.
7) Remove the four Bolts fixing the Shaft using the Box and take
out the Shaft Assembly.
6 HANDLE
5 CONNECTING ROD
4 GUIDE
3 JIG PIN
2 SPIN NUT
1 SHAFT
6-3-1 Procedure 3. Insert the connecting rod ⑤ and handle ➅ into the
square box. Then turn the handle clockwise on the
1. Insert the jig ➂ into the spin-nut ② .
axis of the small box to disassemble (Right-hand
thread).*
2. Insert the guide pin ➃ into the groove of the flange -
shaft by rotating it to the right and left.
LOOSEN LOCK
Guide Pin
Inserting Point
SPIN
BASKET *To disassemble the box, give three to four times of
FLANGE instantaneous shocks to the handle in the
SHAFT loosening direction, then disassemble it by turning
the handle when the nut is loosened.
Auto - off error Power does not turn off despite 3 the buzzer sounds five times Press the "Power"
power-off trials by program with a 0.5sec. ON/0.5sec. OFF button.
cycle. Another buttons do
not work.
Water supply error No frequency change for 60 The buzzer sounds five times Press the "Power"
minutes from water supply. with a 0.5sec. ON/0.5sec. OFF button.
cycle. No other buttons
work.
Drain error Water level does not decrease to The buzzer sounds five times Press the "Power"
the reset point within 6 minutes with a 0.5sec. ON/0.5sec. OFF button.
from draining water. cycle. No other buttons work.
Door open error Door is open during The buzzer sounds five times Close the door.
dehydration cycle. with a 0.5sec. ON/0.5sec. OFF
cycle.
1. Entering : Press the power key while pressing down the WATER LEVEL button.
3. If you press the COURSE key, the test mode changes step by step.
→ 01 → 02 → 03 → 04 → 05 → 06
4. The test is conducted if you press the START/HOLD key when the test mode is in a display state.
7-4 Troubleshooting
7-4-1 Troubleshooting of the Power Supply Board
If any of the following occurs, the PCB is defective. Replace the PCB.
1. Pressing a selection button illuminates the LED display, but the buzzer does not sound.
2. Pressing a selection button sounds the buzzer, but does not illuminate the LED.
3. Pressing a selection button illuminates the wrong LED.
Insert the power plug into the receptacle and press the Power button. If the stored parameters do not display,
check the following :
Is the power NO
Connect the power plug securely.
plug connected?
YES
YES
Is the fuse blown? Replace the fuse.
NO
Is the
connection of the power NO
Check the harness.
trans harness OK?
YES
Is the
output of secondary NO
side of power transformer Replace the transformer.
AC 11V(Red)?
YES
Replace the PCB assembly.
7-4-2 Keyboard
¥ When pressing a selection button, the buzzer does not sound, or the LED does not display.
There is no buzzer sound, and the
LED display does not turn on.
YES
Is the power NO
Turn the power switch on.
switch turned on?
YES
YES
Replace the PCB assembly.
YES
Is the
Start/Hold button NO Press the Start/Hold button.
pressed after selecting Open the faucet.
the course?
YES
Does the
water valve make a YES NO
"Jee" sound when water is Is the fauct open? Open the faucet.
supplied ?
NO Is the connection Is the water YES Close the faucet, pull out the water
of the water valve terminal supply stopped?
all right? hose and turn it off.
YES NO
Is the Is there
winding wire of the any foreign material YES Clean the water valve filter with a
water valve electrically attached to the water hose and
the water valve toothbrush, etc.
connected?
filter?
NO NO
YES
NO
YES
Does the pulsator rotate? Replace the water level sensor.
NO
YES
YES
YES
NO
NO
Is the
water coming out Remove foreign materials such as
through the drain hose with YES
Check the drain valve.
the operation of the drawn thread, hair, pin and buttons.
drain valve?
NO
YES
Is the connection NO
of the water level sensor Connect the terminal securely.
terminal OK?
YES
NO
Does washing continue? Turn off the power, and then start again.
YES
Replace the PCB assembly.
YES
NO
YES
Connect the terminal securely.
YES
NO Is water supplied?
NO
Now it is normal
Does the pulsator
operate normally? NO
YES
Is the V belt NO
positioned correctly? Install the V belt correctly.
The motor is defective.
Check for a racing motor due to
excessively strong or weak tension of
YES the V - belt.
YES
Is the connection NO
of the housing all right? Securely connect it.
YES
Is the winding
wire on the one side of the motor
YES
Replace the motor.
disconnected?
NO
Replace the PCB assembly.
YES
Is the position
NO of the brake lever adjusted
properly?
¥ Defective Dehydration
YES
YES
Does the pulsator rotate?
NO
Any operating YES The clutch is defective.
sound from the drain motor
Is the tension heard? Repair it.
YES
Adjust the tension. of the V - belt excessively
high or low?
NO
NO Is the NO
drain motor electrically Replace the drain motor.
YES connected?
Tell the customer to close the lid. Is the lid open?
YES
NO
Is operation of NO The drain motor is
the drain motor alone
Is the terminal possible? short - circuited.
After checking, YES
of the safety switch lifted up
adjust the safety switch. when closing the YES
lid?
YES
One or two unbalances
automatically corrected through YES
the process of water supply Is the load unbalanced?
and washing.
NO
(The third time causes an
Short - circuited motor. When
"unbalance error".
Spread the laundry evenly, Is operation the motor makes a "woong"
NO
and start again.) of the motor alone sound, the condenser ia
possible? defective, or one side of the
motor windings is shorted.
YES
YES
NO
Is the drain hose lowered? Lower the hose.
YES
YES
Is the drain hose bent? Correct the hose.
NO
Any there
NO
operating sounds from the
drain motor?
YES
Is the NO
Is the drain motor electrically Replace the drain motor.
YES wire connecting the connected?
Securely connect it drain valve and the drain
motor dropped
out? YES
NO
Is operation NO
of the drain motor alone The drain motor is shorted.
Is the possible?
YES
outlet of the drain hose
clogged?
YES
Remove the foreign material NO
completely. Is the wire NO
connection secure? Securely connect it.
Has there drawn
thread, or the like attached to
YES the drain valve? YES
NO
Now it is normal.
No draining.
YES
NO
NO NO
Check grounding Check that the original grounding wire of the washing machine is securely grounded.
Connection of the grounding wire? wire to a gas or water pipe made of vinyl chloride is
very dangerous.
Check the safety Check the operation of the brake. If the following braking times are exceeded, readjust
system or repair the brake system.
Dressing the lead wires Tie the lead wires with a separate wire to prevent them from scattering.
Check that they are securely connected.
Check the locking nuts and screws Check that the nuts and screws are securely locked, and be sure to apply screw lock.
Check inside the washing machine Check for any vinyl wires, screws, or foreign materials inside the washing machine.
Check for oil (lubricant) or In particular, check the surrounding areas of driving units for oil (lubricant) leakage, and
water leakage check the moving parts of the drain valve for water leakage.
Checking the connection of the Check the power cord, plug, and receptacle for any damage. Make sure they comply
power cord with the working voltage.
Adjustment of horizontal level Adjust the height of the two adjusting legs (front of the washing machine) so that
of the washing machine the washing machine is horizontally level.
9
10
11
1
7
2
3
8
4
6
14
15
12
16
17
13
18
19
21
20
3
4
6
7
8
9-1
10
9
12
11
13
14
16
17
15
30 17-1 18
25
31 19
32
20
26
33 21
27 22
34 23
28
29 24
35
10
5 11
6 12
14
15
16
20
17
18
19
17
13
WHITE BROWN
BLACK BLUE
GREEN YELLOW / GREEN
WHITE BROWN
BLACK BLUE
GREEN GREEN / YELLOW
WHITE WHITE
BLACK BLACK
GREEN GREEN
WHITE
BLACK BLACK
WHITE GREEN