WELDING PROCEDURE QUALIFICATION RECORD (WPQR)
N, 07DGO0489PO2A.
Manufacturer M Sud s.r. Lucera (FG)
WPQR No, ozr2007 Dated 26/06/2007
‘Manufacturer's welling procedure (WPS) No, 0207 Dated 23/08/2007
RANGE OF APPROVAL
‘Welding process 135 Type Partly mechanized
Joint type. Plates and Pipes BW ssnb-ssiab-bs/ PY
SingleiMuluple pass Multiple
Parent material yeoup(s) 1-1 (subgroups 1.1 and 1.2 only) CEN ISOTR 15608
Parent material thickness (mm) Butt Joint =3 to 16 Fillet Joint 1) =4 t0 9,6 $4096
‘Throat thickness (mm) No restriction
‘Weld deposit thickness (mm) 3 to 16
Outside diameter (mm) Over 150
Piller metal type Solid wire EN 440 G3 Sil
Shielding gas (EN 439) M2L with mas. CO2% = 43 Racking gas (EN 429) With and without
Type of welding curreat DCEP Heat input Kjvem 9,2 to 15,5
Welding position Pa
Preheat min. (°C) 20 Interpass temp. Max, (°C) 250
Posi weld heat treatment’ Ageing None
Other information =
Welders same Santalucia Giuseppe Stamp No, SG
Welding test conducted by CM Sud s.r, - Lucera (FG)
Mechanical test conducted by CONTROL sne- Ravenna(RA} Laboratory test No. 130
Atpresence of RINA Surveyor G. Cortini
We certify that statements in this cenificae are correct and tha the test welds were prepared, welded and tested in accordance
\with the requirements of UNI EN ISO 15614-1: 2005 Standard
Issued at: GENOVA on 28 hme 2007
Aron
RINA - REGISTRO ITALIANO WAVALE
orm WAQRISHI4 | “12005 Thiscesifoneconsttaf pageCertificate No. O7DGOO48IPOAA Page 244
fen | moe | Cath | Jatt, ana | von |e | RAH] oe
2 135 132) G3sil 240 at 32 12,2 -
<
a}
Lé
‘Thickness (rum) 8 ‘Throat thickness (mm) —N.A.
Prncoss, 135
Deposited metal thickness:
Throat NA.
Consumable insert None \
Other t }
Fom WPORISHL4 012005Certilieate No, O7DGOOASIPOZA, Page 34
Gas
Gas Minune Flow rate (Kimin.)
Trailing - : 5 |
Backing - - c |
POSITION
Welding postion PA
Otte =
PREHEAT POSTWELD HEAT TREATMENT
Preheat temperate 20°C Temperature None
Inerpass temperature 250°C Time NAL
Other Oller
ELECTRICAL CHARACTERISTICS
Cunent DCEP
Ampere (iange) See table Vols (Range) See table
Mode of metal transfor Short are (root pass only} and spray are
Tungsten electiode size and type NAL
Other =
frecuNiQuE
Travel speed (eange) See table
String or weave bead String
Oscillation (*) NA.
Method of groeveledye preparstion Grinding
Inerpass cleaning Brushing
Method of back gouging None
Orifice or gas cup size 20mm
Stand off distance (*)
Multiple or single pass murupre
Multiple or single electrodes Single .
‘Torch engle(*) NA.
‘Other (*) for fully mechanizedirobotic only
ns
Tey
\&
Fon WPQR! S614 1-01-2005Certificate No. O7DGODASIPOYA Page 4/4
‘TRANSVERSE TENSILE TEST
Spec. | width | Thickness “Area Total load Rye TH aciaralicilime
(No) | bnm) (am! [rn OM) (Simm?)
TWrla] 193 18 150,58 87900 584 Ductile failure out of weld
Two] 200 29 18,0 39300 505 Ductile failure out of weld
BEND TEST
Type No. Result
ROOT TRANSVERSE 20FF Acceptable
FACE TRANSVERSE 2081 Aceeptable
IMPACT TEST.
Sui size spesevens Sam
— Test Impact values
Spee No, Notch location Notch type ramp. CC} i
WWE WELD. 1S0-Y 20 36-37-35
VHP 2 HAL Is0-¥ 20 21-19-20
HARDNESS TEST
Location ‘Typertoad Maximum value
Poreat moralja) wVI0 187
HAZ) Wv10 236
Weld metal HVIO 219
OTHER TEST
MACROGRAPITIC EXAMINATION Acceptable
MICROGRAPHIC EXAMINATION Not required
NON DESTRUCTIVE EXAMINATION
VISUAL BXAMINATION Acceptable
RADIOGRAPHIC EXAMINATION Acceptable
PENETRANT TEST Acceptable
MAGNETIC PARTICLE Not required
ULTRASONIC TEST Not required .
Issued at: GENOVA ‘on 28 June 2007
h
how bod _
RINA - REGISTRO ITALIANO NAVALE:
ores WEQRISOH4_1 -O12005