Professional Documents
Culture Documents
MANUAL BOOK
[ASE2000]
Direct Simulation to FRTU
DNP Protocol
29 September 2017
Content
1. System Configuration
2. Start Operation
2.1. ASE2000 (DNP)
2.2.FRTU (DNP)
2.3. ASE2000 (TCP)
2.4. FRTU (TCP)
3. Start Simulation
3.1 Communication
3.2 Read Class
3.3 Control BO
4. Troubleshoot
Setting Over Serial
System Configuration
Serial
Cable
Power
Cable
Supply DC
Power
Supply
USB
To
Serial
Start Operation
ASE2000 (DNP)
ASE2000 (DNP)
ASE2000 (DNP)
ASE2000 (DNP)
For DNP3.0, checklist minimum “ All stations and Class”
Also in RTU Simulations checklist “Enable Unsolicited”
and “Echo Controls”
Start Operation
ASE2000 (DNP)
4. After that , Double Click “Link Status” in column “ Exchange List”
ASE2000 (DNP)
5. Next , Double Click “Class 1/2/3/0 Data” in column “ Exchange List”
This is use for “read Priorty Class and also can check data/value of Status and Analog”.
Start Operation
FRTU (DNP)
FRTU (DNP)
5. Click Save
Start Simulation
Communication
If get answer data like picture above, it’s means success communication
*Indication success communication is , when transmitt (- - >) and get receive (< - -)
Start Simulation
Communication
5. And make sure , on display FRTU Status indicator for “SCADA” (Tx, Rx and RTS) is blinking
Read Class
Read Class
5. And make sure , on display FRTU Status indicator for “SCADA” (Tx, Rx and RTS) is blinking
Additional Info
1. You can also view “Point Values” in ASE2000, by select View Bar
to view DI and AI data in table and compare it with data sheet (Refer to Appendix DNP)
in manual FRTU
LAN Ex:
IP : 192.168.1.20
Cable
Port : 20001
Master ID : 1
Power
Slave ID : 10
Cable
Supply DC
Power Ex:
Supply IP : 192.168.1.10
Port : 20001
Start Operation
ASE2000 (TCP)
3. Click OK
Start Operation
ASE2000 (TCP)
2. Klik “File” -> “Select Protocol” -> “Select DNP3.0 LAN/WAN” -> OK
Start Operation
ASE2000 (TCP)
ASE2000 (TCP)
IP FRTU
Start Operation
ASE2000 (TCP)
FRTU (TCP)
1. Setting In “TCP/IP”
a. IP Address (set ex :192.168.1.20)
b. DNP Port (set ex :20001)
2. Setting In “Master IP Address”
a. Master IP #1 (set ex : 192.168.1.10)
3. DNP Parameter
Slave : ex 10
Unsolicited (Master) : ex 1
4. Save OK
Start Simulation
Communication
If get answer data like picture above, it’s means success communication
*Indication success communication is , when transmitt (- - >) and get receive (< - -)
Start Simulation
Communication
5. And make sure , on display FRTU Status indicator for “Ethernet” (Link and Act) is blinking
Read Class
Communication
5. And make sure , on display FRTU Status indicator for “Ethernet” (Link and Act) is blinking
Control BO
BO means Binary Output, this function to operate digital control on FRTU
Control BO
How to operation :
1. Choose in row 1 what to operate (you can check by open DNP.config FTU)
2. RTU is automatic set, if not, manually set by check slave ID.
Set the frequency as you want
3. Value point at upper column for index, middle column no need set (for counter)
lower column for step to stop the counter
4. After all setting , click send once or send continous
Troubleshoot