Scribd Logo
Upload

Welcome to Scribd!

  • Korg T-Series t1 t2 t3 SM

    Uploaded by

    FKMil
    8 views63 pages
    The korg professional perfomance series T1 T2 T3

    Original Title

    Korg T-series t1 t2 t3 Sm

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Report this Document
    The korg professional perfomance series T1 T2 T3

    Copyright:

    © All Rights Reserved
    Download as PDF or read online from Scribd
    Flag for inappropriate content
    8 views63 pages

    Korg T-Series t1 t2 t3 SM

    Uploaded by

    FKMil
    The korg professional perfomance series T1 T2 T3

    Copyright:

    © All Rights Reserved
    Download as PDF or read online from Scribd
    Flag for inappropriate content
    of 63
    SERVICE MANUAL THE KORG PROFESSIONAL PERFORMANCE SERIES T-SERIES | TIT2T3 CONTENTS 1, SPECIFICATIONS ...... 2, STRUCTURAL DIAGRAM 3. BLOCK DIAGRAM 4. CIRCUIT DIAGRAM 5. P.C.BOARD .. 6. CHECKS 7. REFERENCE 8, PARTSLIST .... 1. SPECIFICATIONS 1) No. of VOICES 2) KEYBOARD 3) TONE GENERATOR 4) WAVEFORMS for SOUND SOURCE 5) QUANTIZATION 6) SAMPLING FREQUENCY TD) No. of PROGRAMS 8) No. of COMBINATIONS 9) SEQUENCER CAPACITY 10) CARD SLOTS 11) INPUT TERMINALS 12) OUTPUT TERMINALS 13) MIDI TERMINALS 14) DISPLAY + 16 voices / 16 oscillators at Single mode 8 voices / 16 oscillators at Double node © 88 key for TL / Type ME (with initial & after touch capabilities ) 76 key for T2 / Type FS (with initial & after touch capabilities ) 61 key for 13 / Type FS (with initial & after touch capabilities ) OC ( optinized covolution ) syster by KORG exclusive LS} ( MB87402, MBB7403A ) 190 waveforas by Sampling & D¥GS and 85 waveforms from DRUM @ PERCUSS]ONS ‘Those are contained in 16x4Mbit MASK ROMs ( G4ibit totally > Further extensible to use sound data from the DS¥-1 and other aodels for MIDI sample dump standards. Then equipped with optional RAMS (using 512Kward x 16bit as the RAM area. ) 16bit 31. 25 Kz 200 ¢ BANK SW. 100 / A+ 100/ By + 100 Approx. 50000 notes, 20 songs / 200 patterns. 8 track. 8 Multi timbers ( dynamic voice allocation ) #1 for PROG / SEQ DATA CARD #2 for PCM DATA CARD Damper pedal. Assignable pedals 1 & 2 1/L & 2/R ( Output impedance less than 10K ohns, Renaining noise less than ~80dBu/JIS-A ) a4 ( Output impedance less than 1K ohms. Remaining noise less than -80dBn/JIS-A) Phones ( Output impedance 100 ohms / STEREO ) IN, THRU, OUT Al & 2. OUT BI & 2 LCD with 240 x 64 full dot aatrix 15) FLOPPY DISK DRIVE Acceptable for a 3.5 inch dia 2HD disk. provided with the following formatting “Normal formatting 4 files / disk. 1 file contains 200 PROGS. 100 COMBI, 64K byte Exclusive data and 50000 note SEQ data. “PCM foraatting 1 file / disk, 1 file contains 200 PROGs, 100 COMBIs. 64K byte Exclusive data. 5000 note SEQ data and 512K vord ( 14B ) PCM data, 16) DIMENSIONS 1478 x 807 x 117. Sam ( TL) 1268 x 355 x 111. 5mm ( 12) 1058 x 355 x 111. Sam ( 73) 17) WEIGHT 35kg (Th). 15.5kg (TZ). 13. 0kg ( 13) 18) POFER CONSUMPTION 139 ADVARSEL! Lithiumbatteri. Eksplosionsfare. Udskiftning ma kun foretages af en sagkyndig, ‘0g som beskrevet i service manualen. Barteriet m3 kun udskitres med batterier af samme fabrikat og type. Usiumparisto! Pariston saa vaintaa ainoastean huoltohenkildst6 saman vaimistajan vastaavalla tyypolld Virheelisesté kasittelysté syntyy rajahdysvaara, FORTI scree on aot ac a 16 PLUK 8 frac tnt 0 cr 8 mc xe 2 Tre # havc 3x10 8 ART AE ART CODE FRO PARE, 41008600 ‘or rave, 548012800 Leo n000 540003800 lo susoezi00 ten tH008 490011000 PC BOARD 1 001137700 901197700 01137700 s4eo2e200 20015700 20020203 WV¥DVIG TWuNLoONUs °z f2o0rsto0 fson3500 sanami¢0 usono00 tusozaeoo ssorsre0 ‘oonteo1 ” “ ‘AEYROARD ANGLE 641010100 é = : ‘REAL 641009800 2 < z ho . f, Za py ee SY ‘573006100 OS GoOQ ra aes lem a reer el Se es cd eee en foot 1s00 011860 Pon CARO rca jrs-8 DF! oF2 Pon RON/RAM I 4 PROGRAM /SEQUENCE CARD neu GA Foc FoD Apc PPI sel Whew 3.5tnch RAM ” ~. 200 Canter —> | | ts KEYBOARD PANEL - JACK 1/0 Leo WVYOVIG 1DO0718 “E 4, CIRCUIT DIAGRAM KUM. 1373 DACILPEACK VO 61-KEYBOARD MATRIX vt Acigeesslues ace ecalme iets rales er] 76/88-KEYBOARD MATRIX KLM 1370 saneanraebl LVSAUFEAMEREEEDIELE coves a owe , Hssaayaaay KLM-1374 POWER SUPPLY JAPAN, UL TRANS Tuno0so. oNu--3rx wNue-ara KLM-1375 POWER SUPPLY CSA TRANS - Tunooso foe + oNu=-3rx wNu--3rx a KLM-1376 POWER SUPPLY 220V, 240V TRANS Traces oNu=-3rx wNue-3rx AFTER TOUCH SENS CIRCUIT MODEL T1 oz = AFTER TOUCH SENS CIRCUIT MODEL T2/T3 KLM-1377 MODEL T1 PANEL CIRCUIT Wz KUM- 1378 KLM-1371/1372 | PANEL CIRCUIT MODEL T2/T3 ewe aiaiebeed 2 Civ oNu--arx om | oe KUR-1371 3701 [lend au ac” (12) KLM-1370 (22V/KLM-1385, VOF /nDE | . ase ene eee eet eee eel eae eee le PCM ROM.RAM SR ene eee ee eee eee = KLM-1374 (FOR 100/117) GuVvOd ‘D'd ‘Ss KLM-13744 ® @ —! nase ene eee eel eet eee eee ele KLM-1375 (FOR 117 CN) cr 2 A z ° = z Ww +E vl =< e cnt oe F caution | KLM~1375A ® °y Bp Hee mee ewe ee eee eee eet ee KLM-1376 (FOR 220/240) . Zz: 2. =: D3 xii, oO: 8 aL KLM-I376A ® 2 KLM-1370 (MOUNT PARTS SIDE) ase eee ee wes eSB eae ee eee ee ee KLM-1370 (NO MOUNT PARTS SIDE) KLM-1371/72 091 1@0 KLM-1377/80 cali a le Fan pene] Su eS we eB es eee ese eens es aes eS ee KLM-1385C ire Fearttin | Ii fh ze KLM-1373 est Nore AS SSS us : A ha! “ee — 6. CHECKS INTRODUCTION This section describes operational procedures and diagnostic self-checks for the Tl / 12 / 73. The followings are subjects to be checked in the self-check node. CAUTION When this checking is done. the data of Tl / T2 / 13 are initialized. Please save the important data like users’ data into the RAM card before you start the checking. FDD (Floppy Disk Drive) ~ Execute Format / Write / Read and check the FDD and FDC ( Floppy Disk Controller, HD632655 ) circuit. 1. AFTER TOUCH Same as the after touch described in item 4 but including to check the function of A/D monitor. PANEL SWs & LEDs Check the S¥s, LEDs and their connections with the panel PCB and check the PPI ( Parallel Port Interface, CXD-1095Q ) circuit. 3. LCD Check the LCD unit and its connections. 4. KEYBOARD & AFTER TOUCH Check the keyboard, its scanner ( ¥B670484 ) circuit and the PCB for after touch. 5. MDE & VDF Check HDB ( ¥B87405 ), DRAM for the MDE, VDF 1 @ 2 ( MB87404 ). ete. 6. TG Check 761 and TG2 ( MB87402. ¥BB7403 ) 7. BASIC OUTPUT SIGNAL Check the PCB circuit for jacks ( OUTPUT terminals ) with reaaining noise. distortion and signal levels, etc 34 8. A/D CONVERTER Check A/D ( UPD7O0IC, 74HC4051, etc. ) circuits and their connections. %*KBASIC OPERATION ‘The check item can be selected by pressing any of BANK / PAGE Sts 0~8 upper row ). ‘The check iten can be shifted to the item just before / next from the item being checked currently by pressing the PAGE — / PAGE + S¥. The check ites can be shifted to the next item by pressing the START / STOP S¥. TO exit from the self-check. press the BANK / PAGE S¥. 9 ( upper row ) and get an indication of "Quit" in the screen. - 3KMEASURING INSTRUMENTS REQUIRED FOR THE CHECK Oscilloscope Noisemeter ( Equalization by 1HFA ) FDD CHECK Turn the POWER ON to start the FDD check while pressing the NUMBER SW 0 LOWER row ) and PROG A SF. 3K Note ! This start-up procedure does not cover the checks for MIDI, PC ROM and battery voltage. Press the NUMBER S¥ 0 ( lower row ) after the self-check mode has started and get an indication of " FDD check " in the screen. ‘The check can be started by pressing the CURSOR POSITION S¥ A~H below the indication of ” Check No.1" in the screen. All the LEDs will light when the check has finished noraally. If there is an error, all the LEDs vill blink and the message wil be indicated in the screen. START-UP OF CHECK MODE Press the NUMBER S¥ 0 ( lower row ) and PROG A SW. and turn the POWER ON to start the check. Confirm that there is no error indication in the screen. Then the screen will proceed to item No.2 When it strats correctly without any error indication. During the start-up, battery voltage for menory back-up will be checked automatically. After that. the itemized check can be started. 35 lf there is an error in this check during the start-up. each error message in the screen will be as follows: Battery voltage for memory back-up ‘The normal voltage ( range ) and the read voltage will be indicated in the hexadecimal notation composed of O~FF. For the above mentioned errors, all the LEDs will blink and the check Will never proceed any nore. PANEL SW& LED 2 Panel Switch & LED Check Push indication Switch Value + If the self-check has started noraally, the screen vill indicate like the above figure and the check will begin with the No. 2 1.Comfirm that all the LEDs light red. The lit LEDs are COMBI. PROG A. PROG B. SEQ, REC, START. STOP, COMBI, E. PROG, GLOBAL, DISK, 2. Press the S¥s according to the indication in the screen and confirm that the touch is normal and the corresponding LED lights. In case of START / STOP. it lights red during pressed and green during released. LCD 1.The LCD screen will get flat in all the area 2.Turn the CONTRAST VR so that the contrast will vary and confirm that there is no blurs in the indication. 3. Press the START / STOP SW to clear the screen 4.[t will proceed to the next ites by pressing the START / STOP SW again. KEYBOARD & AFTER TOUCH 1. Press the key indicated in the screen ( starting from the higher note ) with appropriate pressure one by one. Move to the next key after confirming that the velocity value is between the regulated range ( 20~100 ). If exceeding the range, all the LED will blink. 36 2.The screen will proceed to the after touch when finishing the velocity check for all keys. The indicated value aust be changed suoothly according to the pressing force. 3€The value should reach between 0 and 127, 3. It will proceed to the next item ( MDE, VDF ) by pressing the START / STOP S¥. MDE & VDF 1. Connect the oscilloscope to OUTPUT 1 and set the master volume at ax. 2 Press a C key to get a waveform output with 4 bit length and confirm that the waveform does not change for approx. 2 seconds. ( see FIG.1 ) 3.Press an F key and confirm that no sound by MDE 1 is output 4.1t will proceed to the next item ( TG ) by pressing the START / STOP S¥. TG L-Press a C key / D key and confirm that there is no unusual noise in the OUTPUT respectively. 2. Press an E key and confirm that the waveform like PIG.2 is output. 3. Press an F key and confirm that the waveforms like F1G.3 is output. Pressing a G key will result in the wavefora like FIG. 4. 4.1t will proceed to the next iten ( Basic Output ) by pressing the START / STOP S¥. BASIC OUTPUT SIGNALS 1. Set the MASTER VOLUME at the max and measure the remaining noise. The output signals to be measured are specified by the CURSOR POSITION Sts ANF which correspond to as follows AD #8e OUTPUT I~4 / EWP 8% PHONE L/R 2. Press the VALUE W SW. once to set the output level 8 and start to measure the signal level. Confirm that each output is within the regulated range for the noise level, Signal level, frequency and distorton. 3.Slide the MASTER VOLUME and confirm that the signal level varies smoothly according to the movenent 4. It will proceed to the next item ( A/D CONVERTER ) by pressing the START / STOP SW. 37 A/D CONVERTER 1.Connect EXP-2 to ASS. PEDAL / SW. 1 and 2 located at the rear panel and FOOT S¥. to DAMPER. 2. The screen will indicate JOYSTICK X-Y at first. Confirm that the indicated value changes smoothly according to the movement of the JOYSTICK X-¥. Each ( X,Y ) should reach ~127 or +127 at the side and 0 at the center. 3. It will proceed to the screen indicating A/D other than the JOYSTICK by pressing the START / STOP SI 4.The screen will indicate the values of slider. PEDAL 1, PEDAL 2, and the status of DAMPER. Confira that the value changes snoothly according to the each sovement and reaches between 0 and 127. 5.The screen will proceed to” Quit ” by stepping the DAMPER ON. 1. It can be moved to any of check items by pressing a BANK / PAGE SK. 0~8 ( Upper rom ) during the screen indication ” Quit ” 2. It will proceed to the preload by pressing the CURSOR POSITION key specified as" Quit ” by the screen indication DKRAM CHECK will be carried out internally while moving to the preload after pressing the ” Quit". If there is an error during the RAW CHECK, the screen will indicate the address in reverse color and all the LEDs will blink. The PCM RAM ( Tl and option for 72, 13 ) will be also checked during this stage. 3.Set the preload disk after finishing the RAM CHECK. 4. By pressing the CURSOR POSITION S¥. specified as " LOAD ” by the screen of preload. the preload will be carried out and it will exit from the self-check. 5. The check can be finished after confirming that the preload is done normally. 38 Regulated range / Check item NO.7 Remain Noise | Signal Level | Frequency | Distortion { dBa ] tvj Caz) C#] OUT-1 -83.0 | 40~ 80 488 0.30 | OUT-2 83.0 | 40~ 80 412 0.30 | OUT-3 82.0 | 5.0~ 90 305, 0.30 | OUT-4 82.0 | 506 9.0 244 0. 30 I PH-L 89.0 | 2045 549 0.30 | PH-R 89.0 | 20~ 4.5 610 0.30 | | | | \ A LA ALAS A | \, V vo] | | | L / | | FIG. 1 1 Vidiv FIG.2 0.2 Vidiv FIG.3 0.2 Vidiv (CHECK NO. 5) 2msidiv (CHECK NO.6) 0.2 myidiv (CHECK NO. 6) 0.5 msidiv FIG. 4 0.2 vidiv (CHECK NO. 6) 0.Smsidiv FIG.S 1 vidiv (CHECK NO. 7) 39 7. REFERENCE DATA HD63265SFP PIN FUNCTION ia cS MB622425, PIN FUNCTION pPD23C4000 PIN FUNCTION AO-ALT 00-07. 08-014 = 015/A-1 = WORD / BYTE PIN ASSIGNMENT = ADDRESS. ourPUT OUTPUT 15 ( WORD MODE ) LSB ADDRESS ( BYTE MODE = CHIP ENABLE WODE SELECT BLOCK DIAGRAM 04 0 Oy Ou, On On Ow Ow orperpeperparpatong WORD /BYTE M74HC541GS PIN ASSIGNMENT a e n Bes rr = AS—| Ys Ab I YS ae me Ea 20P2N a »PD7001C PIN ASSIGNMENT BLOCK DIAGRAM so END OF CONVERSION: EBC q DATA LaTCH:DL SERIAL INPUT: st SERIAL CLock :seR SERIAL OUTPUT :s0 uIP sBLecr :

    You might also like