Professional Documents
Culture Documents
BS EN 50363-5:2005+A1:2011
National foreword
ICS 29.035.20
English version
This amendment A1 modifies the European Standard EN 50363-5:2005; it was approved by CENELEC on
2011-03-14. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this amendment the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CENELEC member into its own language and notified to the
Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
© 2011 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Foreword
This European Standard was prepared by the Technical Committee CENELEC TC 20, Electric cables.
The text of the draft was submitted to the formal vote and was approved by CENELEC as EN 50363-5
on 2005-11-01.
EN 50363 (in all its parts) supersedes the equivalent information at present in HD 21.1 S4,
HD 21.14 S1, HD 22.1 S4, HD 22.10 S1, HD 22.14 S2 and prHD 21.15 S1. The existing information in
these HDs will be deleted at the next maintenance review.
Foreword to amendment A1
The text of the draft was submitted to the Unique Acceptance Procedure and was approved by
CENELEC as amendment A1 to EN 50363-5:2005 on 2011-03-14.
_______________
–3–
Contents
1 Scope .................................................................................................................................................4
3 Definitions...........................................................................................................................................4
4 Properties ...........................................................................................................................................4
Table 2 – Requirements for the tests for halogen-free crosslinked insulating compounds .....................5
BS EN 50363-5:2005+A1:2011
EN 50363-5:2005+A1:2011 (E) –4–
1 Scope
This part of EN 50363 specifies the requirements for the physical properties of the harmonised
halogen-free, cross-linked insulating compounds given in Table 1. The relevant test methods are given
in EN 60811 series, EN 50267-2 (series), EN 60684-2 and EN 50396.
NOTE 1 Requirements for smoke emission, which are based on tests on cables and not individual materials, are given in the
relevant cable standard.
2 Normative references
For the purposes of this part of EN 50363, the requirements of EN 50363-0, Clause 2, apply with
regard to normative references.
3 Definitions
For the purposes of this part of EN 50363, the definitions given in EN 50363-0, Clause 3, apply.
4 Properties
Each compound shall meet the particular requirements listed in Table 2, when using the test methods
referenced in columns 4 and 5.
NOTE For cross-references to the latest editions of the test method standards see Table 2 of EN 50363-0.
–5–
Table 2 – Requirements for the tests for halogen-free crosslinked insulating compounds
1 2 3 4 5 6 7
a
Ref No Test Unit Test method described Type of compound
b
in EN 60811
Section Clause EI 5 EI 8
1 Mechanical properties
1.1 Properties before ageing 1-1 9.1
1.1.1 Values to be obtained for
the tensile strength:
- median, min. N/mm² 10,0 5,0
1.1.2 Values to be obtained for
the elongation at break:
- median, min. % 125 125
1.2 Properties after ageing in 1-2 8.1.3.1
air oven
1.2.1 Ageing conditions:
- temperature °C 135 ± 2 !135 ± 2"
- duration of treatment h 7 x 24 7 x 24
1.2.2 Value to be obtained for
the tensile strength:
- median, min. N/mm² - -
c
- variation, max. % ± 30 - 30
1.2.3 Values to be obtained for
the elongation at break:
- median, min. % - 125
- variation, max. % ± 30 ± 30
2 Hot set test 2-1 9
2.1 Conditions of treatment:
- temperature °C 200 ± 3 200 ± 3
- time under load min 15 15
- mechanical stress N/cm² 20 20
2.2 Test requirements:
- max. elongation under % 100 100
load
- max. elongation after % 25 25
unloading
BS EN 50363-5:2005+A1:2011
EN 50363-5:2005+A1:2011 (E) –6–
Table 2 – Requirements for the tests for halogen-free crosslinked insulating compounds
(continued)
1 2 3 4 5 6 7
a
Ref No Test Unit Test method described Type of compound
b
in EN 60811
Section Clause EI 5 EI 8
3 Pressure test at high 3-1 8.1
temperature
3.1 Test conditions:
e
- force exerted by the N 3-1 8.1.4 -
d
blade
e
- duration of heating h 3-1 8.1.5 -
under load
- temperature °C 100 ± 2 -
3.2 Result to be obtained:
- median of the depth of % 50 -
indentation, max.
4 Bending test at low 1-4 8.1
temperature
4.1 Test conditions:
- temperature °C - 15 ± 2 - 15 ± 2
e e
- period of application of h 1-4 8.1.4
low temperature
f f
4.2 Result to be obtained
5 Elongation test at low 1-4 8.3
temperature
5.1 Test conditions:
- temperature °C - 15 ± 2 - 15 ± 2
e e
- period of application of h 1-4 8.3.4
low temperature
5.2 Result to be obtained:
- elongation without % 30 30
break, min.
6 Ozone resistance test
6.1 Method A 2-1 8
- test temperature °C 25 ± 2 25 ± 2
- test duration h 24 24
- ozone concentration % (250 to (250 to
-4 -4
(by volume) 300) x 10 300) x 10
6.2 Method B EN 50396 8.1.3
- test temperature °C 40 ± 2 40 ± 2
- test duration h 72 72
- ozone concentration % (200 ± 50) (200 ± 50)
-6 -6
(by volume) x 10 x 10
f f
6.3 Result to be obtained
–7–
Table 2 – Requirements for the tests for halogen-free crosslinked insulating compounds
(continued)
1 2 3 4 5 6 7
a
Ref No Test Unit Test method described Type of compound
b
in EN 60811
Section Clause EI 5 EI 8
7 Assessment of
halogens
7.1 - pH, min. EN 50267-2-2 4,3 4,3
7.2 - conductivity, max. µS/mm EN 50267-2-2 10 10
7.3 - amount of halogen acid
gas
- HCl and HBr, max. % EN 50267-2-1 0,5 0,5
g
- HF, max. % EN 60684-2 0,1 0,1
a
Information on other tests is given in EN 50363-0, Clause 5.
b
Unless stated otherwise.
!c No limit for the positive tolerance. "
d
For EI 5 a value of k = 1,0 shall be used to calculate the force.
e
See test method referred to in columns 4 and 5.
f
No cracks.
g
This test need not be performed if a negative result is obtained for fluorine in the test to Annex D of HD 21.14.
+A1:2011
BSI - British Standards Institution
BSI is the independent national body responsible for preparing British
Standards. It presents the UK view on standards in Europe and at the
international level. It is incorporated by Royal Charter.
Revisions
British Standards are updated by amendment or revision. Users of British
Standards should make sure that they possess the latest amendments or
editions.
It is the constant aim of BSI to improve the quality of our products and services.
We would be grateful if anyone finding an inaccuracy or ambiguity while using
this British Standard would inform the Secretary of the technical committee
responsible, the identity of which can be found on the inside front cover. Tel:
+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.
BSI offers members an individual updating service called PLUS which ensures
that subscribers automatically receive the latest editions of standards.
Buying standards
Orders for all BSI, international and foreign standards publications should be
addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996
7001 Email: orders@bsigroup.com You may also buy directly using a debit/credit
card from the BSI Shop on the Website http://www.bsigroup.com/shop
In response to orders for international standards, it is BSI policy to supply the
BSI implementation of those that have been published as British Standards,
unless otherwise requested.
Information on standards
BSI provides a wide range of information on national, European and
international standards through its Library and its Technical Help to Exporters
Service. Various BSI electronic information services are also available which
give details on all its products and services. Contact Information Centre. Tel:
+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: info@bsigroup.com
Subscribing members of BSI are kept up to date with standards developments
and receive substantial discounts on the purchase price of standards. For details
of these and other benefits contact Membership Administration. Tel: +44 (0)20
8996 7002 Fax: +44 (0)20 8996 7001 Email: membership@bsigroup.com
Information regarding online access to British Standards via British Standards
Online can be found at http://www.bsigroup.com/BSOL
Further information about BSI is available on the BSI website at http://
www.bsigroup.com
Copyright
Copyright subsists in all BSI publications. BSI also holds the copyright, in the
UK, of the publications of the international standardization bodies. Except as
permitted under the Copyright, Designs and Patents Act 1988 no extract may
be reproduced, stored in a retrieval system or transmitted in any form or by any
means – electronic, photocopying, recording or otherwise – without prior written
BSI Group permission from BSI.
Headquarters 389 This does not preclude the free use, in the course of implementing the standard,
Chiswick High Road, of necessary details such as symbols, and size, type or grade designations. If
London, W4 4AL, UK these details are to be used for any other purpose than implementation then the
Tel +44 (0)20 8996 9001 prior written permission of BSI must be obtained.
Fax +44 (0)20 8996 7001
www.bsigroup.com/ Details and advice can be obtained from the Copyright and Licensing Manager.
standards Tel: +44 (0)20 8996 7070 Email: copyright@bsigroup.com