Professional Documents
Culture Documents
------------------------------------------------------------------------------------
ALL 42 PAGES AT EDITION 04 COMPUTER GENERATED (IDSS)
------------------------------------------------------------------------------------
CONTENTS
7. NSC-PREPARATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
14. MISCELLANEOUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
04
This procedure describes the loading of new system software-mode and the
copy of actual data from the old software-mode into this new system
software-mode at an operational exchange.
- After the REPLACEMENT all routine tests are replaced with the
data from the old DLS and the same test numbers are active.
For the extended hardware no tests are activated.
04
- SLT/SLP : contains all DATASETS for the new software (CODE and DATA)
- The following tapes or disks are optional.
ELT1/ELP1: contains the software or data corrections necessary for
the data transfer in the old software-mode.
ELT2/ELP2 and ELT3/ELP3 contain additions and corrections for the
new software.
Before loading and execution of optional software check the
delivered "TAPE/DISK INFORMATION" carefully ``
04
04
04
After DISK-INIT PLCE-A contains the new software, the software for
replacement data transfer and control-relations for the replacement.
On the PLCE-A following relations are necessary for the datatransfer:
04
04
+ reset of
R_EXT_HWSW.D_EXT_TAPE
update of relations possible
operator-request will be
saved in new: R_E_STATV4
after UPDATE-NEW-DLS:RESET
a next EXTEND-EXCH is
"NOT SUCCESSFUL"
Remarks:
04
- SYSTEM-VDU (ATOM-PC)
- SYSTEM-PRINTER + enough paper or ELECTRONICAL DUMP-MEDIUM (PC)
- DRIVE for optical disk on PLCE-A (NA=H'C)
- DRIVE for optical disk on PLCE-B (NA=H'D)
- optional MAGTAPE-UNIT on PLCE-A (NA=H'C)
- optional MAGTAPE-UNIT on PLCE-B (NA=H'D)
Note: User-tapes and optical disks have to be removed from the peripherals
by customer.
04
NO: go to step 6
YES: continue
(1) COPY-VOLUME:SRCDEV=DKB2Px,DESTDEV=DKB1;
(x - partition-number)
(1) MANAGE-DURS:IMPLMENT,ALLDURS,MEMUPD=FALSE;
(2) INITIATE-COMPOUND-DIALOGUE:SRCDEV=DKB1,ERRMODE=SKIP,LOGMODE=LOGON,
SRCFILE=x,LOGFILE=y
04
04
RESTART-CE:SBLTYPE=CTLE,NBR=1,NA=H'C;
GO:REPLY=CONFIRM,SEQNBR=argu1;
DISABLE:SBLTYPE=DISC,NBR=1,WTC=0,NA=H'C;
GO:REPLY=CONFIRM,SEQNBR=argu1;
DISABLE:SBLTYPE=CTLE,NBR=1,WTC=0,NA=H'C;
GO:REPLY=CONFIRM,SEQNBR=argu1;
This handling is necessary if you intend to replace the disk with the old
software by a spare-disk. If not, then go to next step.
04
INITIALI:LOADSRC=OPTDISC,PARTNBR=1,SBLTYPE=CTLE,NBR=1,NA=H'C;
After the task has been entered, the PLCE-A is booted from disk
and then it goes to "ISOLATED MODE". In the isolated mode the middle
LED is flashing and the other two LEDs are off.
No report will appear.
After successful isolation the password for PLCE-A is
SYSTEM12-A
04
NO: go to step 3
YES: go to step 5
COPY-VOLUME:SRCDEV=DKA2Px,DESTDEV=DKA1;
(x - partition-number)
UNMOUNT-DISK:LDEV=DKA2P0; NOTE2
If there was a file with logical fileID = 116 copied, then enter
(1) MANAGE-DURS:IMPLMENT,ALLDURS,MEMUPD=FALSE;
If there was a file with logical fileID = 4 copied, then enter
(2) INITIATE-COMPOUND-DIALOGUE:SRCDEV=DKA,ERRMODE=SKIP,
SRCFILE=x,LOGFILE=y;
04
04
ACE-RECONFIG:NOW;
DISPLAY-SCHEDULE;
(1) REMOVE-SCHEDULE:SCHEDID=argu1
(2) ACTIVATE-SCHEDULE:SCHEDID=argu1,CONTR=SCHED&MM&DD&hh&mm;
3. Cancel CRM-timer
VERIFY-CRM-RECORD:DISPLAY;
VERIFY-CRM-RECORD:DELETE;
04
DISPLAY-MEA-STATUS;
DISPLAY-MEA-DATA:IDENTITY=argu1;
DEACTIVA-GEN-STAT:IDENTITY=argu1;
Note: The customer has to be informed that all measurement-jobs have been
deactivated. A recreation must be done by customer according to the
support information SI 134 after replacement `
04
*****************************************************************
* Enter the following commands at the local SYSTEM-terminal *
* in the replacement-exchange (remote or collocated NSC) *
*****************************************************************
Now a last file transfer from the REPLACEMENT-EXCHANGE to NSC can be done
for BILLING-files and other important files by customer.
After execution of step 2 no file-transfer is possible but
files can be saved to tape or to optical disk in the REPLACEMENT-EXCHANGE
to a local medium.
DISPLAY-SITELIST;
MODIFY-CRM-MEDIUM:LOCAL,ALL;
DISPLAY-REROUTE-MAP;
REROUTE-REPORTS:REPGRP=ALL,SITE2=SUPPRESS,SITE1="argu1";
REROUTE-REPORTS:ALMIND=TONONE,SITE1="argu1";
04
*************************************************************************
* This step is a request for customer to save all related billing- *
* and measurement- files to the provided medium (tape, optical disk ..).*
* Enter the commands at the NSC-terminal *
*************************************************************************
DEALLOCA-LOCAL-FILE:ALLFILTY,SITE=argu1;
YES: continue
*****************************************************************
* Enter the following commands in this section *
* at the NSC-terminal in the NSC *
*****************************************************************
DISPLAY-SCHED-JOB:ALLJOB;
Note: The report contains information about the jobs. Remember jobs in
state "STOPPED" or "ERROR" for RESUME-SCHED-JOB after replacement
or for fallback.
04
RESUME-SCHED-JOB:JOBNBR=argu1;
If there are any local-copy jobs in job state "COPIED" and timing type
Note3 is not "immediately" , the copied files have to be deactivated,
DEALLOCA-LOCAL-FILE:VFILTYPE="argu1",SITE="argu2";
SUSPEND-SCHED-JOB:JOBNBR=argu1;
DISPLAY-SCHED-JOB:JOBNBR=argu1
04
DELETE-SCHED-JOB:JOBNBR=argu1;
DISPLAY-SCHED-JOB:ALLJOB;
YES: continue
NO: continue
YES: inhibit the data transfer from the exchange (NSC) to the EDP-Center
MODIFY-EDPC-CONN:CONNECT=OFF,EDPC="argu1";
Inform the personal of EDPC(s) that a replacement will take place and
no modification of any data is allowed by EDPC-personal.
The access of EDPC to the replacement-exchange should be blocked by
modifying the password. The default password is 13971.
04
HANDLE-JTS-DATA:MODIFY,JOBTYPE=RMTMMC,
SITETYP=EDPC,SITE="argu1",OLDPSW=13971,PASSWORD=13972,VFYPSW=13972;
YES: continue
press <F9>
PASSWORD: argu1/
DESTINATION: argu2;
MODIFY-CRM-MEDIUM:ALL,LOCAL.
REROUTE-REPORTS:SITE2=SUPPRESS,REPGRP=ALL,SITE1="argu1".
REROUTE-REPORTS:ALMIND=TONONE,SITE1="argu1".
04
COPY-LOCAL-FILE:ALLFILTY,SITENAME=argu1,DSTDEV=argu2;
DEALLOCA-LOCAL-FILE:ALLFILTY,SITE=argu1;
TRIGGER-SPOOLER-REROUTE:DISPLAY
TRIGGER-SPOOLER-REROUTE:DEVTYPE=argu1,DEVNBR=argu2,NA=H'argu3,
NDEVTYPE=argu4,NDEVNBR=argu5,NEWNA=H'argu6;
Repeat the REROUTE command until all queues are empty, if required
by customer.
04
******************************************************************
** This is the main procedure of the SLT-replacement **
******************************************************************
EXTEND-EXCH;
Note: This process can last several hours, depending on the size
of the exchange. During this time, no semi-permanent data
(e.g. subscriber data) can be changed by operator, because the related
data tables are protected from further changes.
The relation R_EXT_UPD contains the relation-id's which are blocked
for modifications. It is not allowed to modify any data during a
replacement without confirmation by system specialists.
Every 5 minutes, an INTERIM report with the current status of data transfer
is produced.
04
UPDATE-NEW-DLS:RESET;
After the first copy procedure the domain D_ADD_PAR2 is changed for
all files, which were copied. Undo this flag for all DB-files.
( Check for relevant FileIds :
DISPLAY-RELATION:1="R_E_FILE",2="D_ADD_PAR2"&1&"0000"; )
MODIFY-TUPLE:1="R_E_FILE",2="D_NFILEID"&0&"argu1.1",
3="D_ADD_PAR2"&0&"0000";
04
MODIFY-TUPLE:1="R_CDE_CHIN",ALL,
3="D_CDE_SPAR"&0&"0020000000000000000000006000000000000000"
MODIFY-CRM-CONFIG:CALLTYPE=DBLNG,CLEAR;
EXTEND-EXCH:RESTDAT;
04
YES:
Choose the correct commands - flagged by (1) and/or (2) -
for different possibilities.
NO: go to step 3
COPY-VOLUME:SRCDEV=DKA2Px,DESTDEV=DKA1; NOTE2
(x - partition-number)
UNMOUNT-DISK:LDEV=DKA2P0;
(1) MANAGE-DURS:IMPLMENT,ALLDURS,MEMUPD=FALSE;
(2) INITIATE-COMPOUND-DIALOGUE:SRCDEV=DKA,ERRMODE=SKIP,
SRCFILE=x,LOGFILE=y;
04
LOAD-EXCHANGE;
CONFIRM-LOAD-EXCHANGE;
Note: Before loading the exchange PLCE-A needs about 5 minutes for
collecting the loading-data. This is a normal system behavior.
Is a NSC present ?
YES:
BUILD-REMOTE-DISK;
04
NO: go to step 3
YES: go to step 5
COPY-VOLUME:SRCDEV=DKA2Px,DESTDEV=DKA1;
(x - partition-number)
UNMOUNT-DISK:LDEV=DKA2P0; NOTE2
(1) MANAGE-DURS:IMPLMENT,ALLDURS;
(2) INITIATE-COMPOUND-DIALOGUE:SRCDEV=DKA,ERRMODE=SKIP,
SRCFILE=x,LOGFILE=y;
04
*** The customer must decide if the exchange works correctly ***
NO: continue
04
1. Disable PLCE-B
DISABLE:SBLTYPE=DISC,NBR=1,WTC=0,NA=H'D;
DISABLE:SBLTYPE=CTLE,NBR=1,WTC=0,NA=H'D;
GO:REPLY=CONFIRM,SEQNBR=argu1;
To prepare of second disk (PLCE-B disk) two different ways can be used:
Note: HARDINIT will cause heavy traffic to the PLCEs and it takes several
hours. We recommend to choose this option only if there is enough
time available, until normal callhandling traffic starts again.
Choose one strategy `
MOUNT-DISK:LDEV=DKA2P0,VOLIDF=<disk-name>; NOTE1
START-DISK-BACKUP:SLPDLP=Y,SRCDEV=DKA1,DDEVSLP=DKA2P0,DDEVDLP=DKA2P1,
DLPIDF="replbut",SLPIDF="replbut",EXCLUDE,
FILETYPE=TAXATION&STAFILE;
UNMOUNT-DISK:LDEV=DKA2P0; NOTE2
Remove the optical-disk from PLCE-A and insert it onto PLCE-B.
INITIALI:SBLTYPE=CTLE,NBR=1,NA=H'D,LOADSRC=OPTDISC,PARTNBR=1;
04
INITIALI:SBLTYPE=CTLE,NBR=1,NA=H'D,LOADSRC=OPTDISC,PARTNBR=1;
Note: The disk of PLCE-B is still in state 'OPR' - only the bottom LED
of PLCE-B is flashing `
04
2. DIAM connection
#### # # #### ##
# ## # # # ### #
### # # # # # # # ###
# # ## # # # # #
#### # # #### ### #
_______________________________________
04
This section describes general handlings for a fallback to the old software
package, if the functionality with the new software-package is not given.
This section describes the fallback-strategy to the old software
package, if the functionality of the exchange with the new software-package
is not given in a correct way.
(2.) The exchange is "running" simplex with the new software package :
Do system-start-up based on CPM-B.
Go to step 2 .
(3.) The exchange is (still) "running" with the old software package :
Roll back all changes which were done for the SLTR
Go to step &STEP1203 .
RESTART-CE: NA=H'D,SBLTYPE=CTLE,NBR=1
DISABLE: NA=H'D,SBLTYPE=CTLE,NBR=1,WTC=0;
GO: SEQ=argu1,REPLY=CONFIRM
argu1 = see SEQUENCE-NUMBER in DISABLE command ( RRN= 0051 )
04
() UPDATE-NEW-DLS:RESET;
() MODIFY-TUPLE:1="R_CDE_CHIN",ALL,
3="D_CDE_SPAR"&0&"0000000000000000000000006000000000000000";
04
If the new software contains a new MMC-package also the name of the
market segment is changed.
In this case the ATOM-handling works not correctly or is blocked.
DISPLAY-SITELIST;
HANDLE-EXCH-SITELIST:MODIFY,SITEID=argu1,MSEG="argu2";
TRANSFER-NETWORK-DATA:SITEID=argu1;
2. Re-connect of report-transfer
REROUTE-REPORTS:ALMIND=TOSITE1,SITE1="argu1",SITE2="argu2";
REROUTE-REPORTS:REPGRP=ALL,SITE1="argu1",SITE2="argu2";
Definition of arguments:
3. Re-connect of file-transfer
DISPLAY-REROUTE-MAP;
MODIFY-CRM-MEDIUM:ALL,NSCCON;
04
1. NSC-FILE adaption
If the new software contains a new MMC-package then also the market
segment-name is changed. In this case the access of NSC terminals can not
work correctly.
The adaption must be done in the NSC-exchange by modifying the SITELIST and
in the ATOM-PC by installing a new ATOM-package.
DISPLAY-SITELIST;
HANDLE-NSC-SITELIST:MODIFY,SITEID=argu1,MSEG="argu2";
TRANSFER-NETWORK-DATA:ALLSITES,SITELIST;
Start the file-transfer and the alarm and report routing to the NSC.
The following commands have to be entered for all exchanges (destinations)
which are supervised by the NSC (see report of DISPLAY-SITELIST;).
04
REROUTE-REPORTS:SITE1="argu1",SITE2="argu2",ALMIND=TOSITE1;
REROUTE-REPORTS:SITE1="argu1",SITE2="argu2",REPGRP=ALL;
Definition of variables:
MODIFY-CRM-MEDIUM:ALL,NSC;
4. Re-connect of EDP-Center(s)
MODIFY-EDPC-CONN:CONNECT=ON,EDPC="argu1";
HANDLE-JTS-DATA:MODIFY,JOBTYPE=RMTMMC,SITETYP=EDPC,SITE="argu1",
OLDPSW=13972,PASSWORD=13971,VFYPSW=13971;
04
DISPLAY-SCHED-JOB:ALLJOB;
DELETE-SCHED-JOB:JOBNBR=argu1;
Are there any NSC file transfer-jobs in state " ERROR " then:
RESUME-SCHED-JOB:JOBNBR=argu1;
04
1. Modifications by MPTMON-MACRO
DIAM:
- MODIFY-TUPLE:1="R_TCE_LIST",2="D_TCE_INDX"&0&"found index",
3="D_LCE_ID"&0&"1-st DIAM-LCEID";
MODIFY-TUPLE:1="R_TCE_LIST",2="D_TCE_INDX"&0&"found index+1",
3="D_LCE_ID"&0&"2-nd DIAM-LCEID";
- MODIFY-TUPLE:1="R_ANN_DATA",2="D_ANN_HUNT"&0&"0",
3="D_TRA_IDX"&0&"block-nbr";
- MODIFY-TUPLE:1="R_L_ANDEST",2="D_S12ANN"&0&"8",
3="D_ANDEST1"&0&"19000300000000000000";
04
AUTHOR:
UNIT:
DEPARTMENT:
EXTENSION:
END OF DOCUMENT
04