Inert Gas System —-
j 2 KANGRIM
Instruction Manual
SERVOMEX
General operating and serving in structions- Oxygen Analyzer
Chapter = 1
JRIM HEAVY INDUSTRIES CO.UTD.Captive MB screw (4 off)
Captive M6 screw (4 off
MB mounting stot (4 off
Purge outlet? NPT (fused)
6.
12.
‘sample outlet? NPT
‘Sample inet? NPT.
Cable entiies ? NPT (Soff)
MG earth terminal
Purge inlet? NPT (if used)Xendos 1800 MY Start-Up and Shut-Down Procedure
‘The folowing tips may assist (echnicians in the start-up and shut-down of the 1800M1V_
‘Marine Oxygen Analyzer. These instructions are for the Servomex 1800 MV with the
wet gas bubbler unit.
1800 MV MARINE OXYGEN ANALYZER
‘SUGGESTED START-UP PROCEDURE.
1. Check to see ALL gas valves o unit are closed.
2. Open bubbler fil opening. Fill bubbler bowl approximately 2/3rds fll with
‘lean water, Close il opening
1 flow coutrol valve is closed.
3. Make sure b
4. Apply power to analyzer. Let unit ware up for atleast ywo hours.
iy open zero gas.
6. Set input sample /cal gas regulator to 3 PSL
17. Again check to see gas regulator is set at 3 PSI.
fol valve and set low fo media gas
bubble flow ia the bubbler:
saaely five minutes
9. Let
88 low for
10, Unit is now
ter a successfl calibration, selector valve cam be put (03
‘+0 This is reconrinended (0 avoid problems with condensation, Note that been
technology is diferent fo electrochemical or zirconia type
analyzers, once switehed on the unit eau be lefl powered wp without reducing,
cel lifetime, ***
KangRtim fn1800 MV MARINE OXYGEN ANALYZER SUGGESTED
‘SHUT-DOWN PROCEDURE,
iycer uses a non-depleting “paramaga
{As the Servomex IS00MY oxygen a
measurement cell itis not necessary to shut the an
‘order (o preserve eel life, Leaving the wit switched on ensures i is always ready forse
iyzer down between ussge in
1. Closed off sample input valve fo system, -
2. Check and make sure ALL gas ines i unit are closed.
3. Open zero gas and seta medium flow on gas bubbler.
4. Close off zero gas at supply. Do not adjust bubbler flow valve,
rubbler bowl. Close drain outlet
5, Drain ALL water contents fr
n-rero gas supply.
7. Let zero eas flow for approximately 5 minutes.
scat be at 0
lepending on the
8. Close zero gas at source. Analyzer rea
concentration of the zero 35.
9. Remove power from unit
10, Unit is wow shutdown and cells dry.
Recommended 1800MV Marine Oxygon Analyser Sample System
Cat Panel :
rameaee
Sone
sap
cosine wi
|
ae eon (
ses ake
a
a a
eee
Green (icocetesa ves
(Essa
‘ator pel odes cose cont
Hl
|
t
1
|
IXendos 1800MY Installation Tips
When upgrading from another oxygen analyzer toa Servomex 1800MV Marine
‘Oxygen Analyzer, modifications must be made to your calibration panel to raluce
the risk of damaging the measuring cell by accidentally over-pressurising the cell or
allowing moisture to enter it.
Is are not covered by the
gent can supply simple
is important to note that damaged measuring e
Servomex warranty. If required Servomesx, or an approved.
‘calibration panel or modify your existing calibration panel for use with the 1800MV_
‘Marine Oxygen Analyzer.
astalling and operating the
‘The following tips may assist technician
Servomex 1800MV Marine Oxygen Analyzer.
CAUTION
1 sample pressure and flow rate for the Servomex 1800MV analyzer is
Iethe analyzer is exposed to a higher pressure or flow rate
be damaged and unable fo function properly.
WHEN INSTALLING THE 1800MV UN
FOLLOW THESE PRECAUTIONS,
ist be regulated
uding sample and zero and span calibration gases
103 psig upstream of the 1800MV analyzer
is recommended (o ital an inline pressure regulator before the wet gas
1AM gases i
bubbler Gregulate the delivery ofall gases C03 psi.
tbe taken,
layion of the pressure regulator, extream care mm
Without the inst
when switebing fro
calibration gas, the flow controler on the wet gas bubbler must to be adjusted
downward (o prevent the calibration gas from bei
roller is not adjusted, the bubbler may blow mois
wd possible irreversible cell damage
sample (oa calibration gas.Before switching (0 the
introduced at higher press
re up into the
Hf the flor
call resulting in cell contarninatio
eee me
oe op (0-0 |
+p: 20.9%
- seeseeeee Op 0%
valve close, Galva close, Valve close
2, @Yalve open, Bale open ‘Supply standard gas (90%)
1. Adjust ® Flower meter (Anox 200~400ce/Min) ~—~ Calbation (0%)
adjust @ Set ZERO potenionmeter (Q, 0%) —--—~ Please refer to the allached Fia.2 Analyser
valve close, Baie close:
yale open, vale open,
‘Aaiust 8 Flow moter Aprox 900-400 colin)
7 ust @ Sot SPAN potentonmetor (0 20.9%)
~ Supply calibration Ai (Aprox 20.6%)
Please toler to the attached Fig.02 Analyser