Professional Documents
Culture Documents
Specifications: Roof Rack Bolts 6 53 Spoiler Nuts 6 53
Specifications: Roof Rack Bolts 6 53 Spoiler Nuts 6 53
2008 ACCESSORIES & BODY, CAB Exterior Trim and Ornamentation - Edge & MKX
SPECIFICATIONS
TORQUE SPECIFICATIONS
Description Nm lb-in
Roof rack bolts 6 53
Spoiler nuts 6 53
Microsoft
Friday, September 25, 2009 11:03:01
11:02:58 AM Page 1 © 2005 Mitchell Repair Information Company, LLC.
2008 Ford Edge SE
2008 ACCESSORIES & BODY, CAB Exterior Trim and Ornamentation - Edge & MKX
1. Remove the front bumper cover. For additional information, refer to BUMPERS article.
2. Remove the isolator-to-bumper cover bolts.
3. Remove the isolator-to-radiator grille reinforcement screws.
4. Remove the isolator.
Release the isolator from the clips on the bumper cover.
6. Remove the radiator grille-to-radiator grille reinforcement nuts and remove the radiator grille.
7. To install, reverse the removal procedure.
ROOF RACK
Microsoft
Friday, September 25, 2009 11:02:58 AM Page 3 © 2005 Mitchell Repair Information Company, LLC.
2008 Ford Edge SE
2008 ACCESSORIES & BODY, CAB Exterior Trim and Ornamentation - Edge & MKX
Microsoft
Friday, September 25, 2009 11:02:58 AM Page 4 © 2005 Mitchell Repair Information Company, LLC.
2008 Ford Edge SE
2008 ACCESSORIES & BODY, CAB Exterior Trim and Ornamentation - Edge & MKX
NOTE: The roof rack side rail has a tab located at the front of the ditch moulding
Microsoft
Friday, September 25, 2009 11:02:58 AM Page 5 © 2005 Mitchell Repair Information Company, LLC.
2008 Ford Edge SE
2008 ACCESSORIES & BODY, CAB Exterior Trim and Ornamentation - Edge & MKX
and it is installed under the windshield moulding. When installing the roof
rack side rail, start at the front of the vehicle and work toward the rear.
SPOILER
Microsoft
Friday, September 25, 2009 11:02:58 AM Page 6 © 2005 Mitchell Repair Information Company, LLC.
2008 Ford Edge SE
2008 ACCESSORIES & BODY, CAB Exterior Trim and Ornamentation - Edge & MKX
1. Remove the liftgate trim panel. For additional information, refer to INTERIOR TRIM AND
ORNAMENTATION article.
2. Disconnect the electrical connector and the rear windshield washer hose from the rear spoiler.
Fig. 10: Identifying Electrical Connector & Rear Windshield Washer Hose
Courtesy of FORD MOTOR CO.
NOTE: There are 4 pin-type retainers on the bottom of the spoiler. When removing
the spoiler it is difficult to access the retainers to release them from the
liftgate. It may be necessary to pry upward on the rear spoiler to release it
from the retainers. Do not pry on the window.
Microsoft
Friday, September 25, 2009 11:02:58 AM Page 8 © 2005 Mitchell Repair Information Company, LLC.
2008 Ford Edge SE
2008 ACCESSORIES & BODY, CAB Exterior Trim and Ornamentation - Edge & MKX
Microsoft
Friday, September 25, 2009 11:02:58 AM Page 9 © 2005 Mitchell Repair Information Company, LLC.
2008 Ford Edge SE
2008 ACCESSORIES & BODY, CAB Exterior Trim and Ornamentation - Edge & MKX
Fig. 15: Identifying Rocker Panel Molding End Cap & Screws
Courtesy of FORD MOTOR CO.
2. Remove the 2 screws from the rocker panel moulding inside the rear wheelhouse.
Fig. 16: Identifying Screws From Rocker Panel Moulding Inside Rear Wheelhouse
Courtesy of FORD MOTOR CO.
5. Pull outward to release the rocker panel moulding from the body, starting from the front of the vehicle
moving rearward.
6. To install, reverse the removal procedure.
Microsoft
Friday, September 25, 2009 11:02:58 AM Page 10 © 2005 Mitchell Repair Information Company, LLC.