Professional Documents
Culture Documents
Version 1.0
Published March 2014
Copyright©2013 ASRock INC. All rights reserved.
Copyright Notice:
No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRock Inc.
Products and corporate names appearing in this documentation may or may not
be registered trademarks or copyrights of their respective companies, and are used
only for identification or explanation and to the owners’ benefit, without intent to
infringe.
Disclaimer:
Specifications and information contained in this documentation are furnished for
informational use only and subject to change without notice, and should not be
constructed as a commitment by ASRock. ASRock assumes no responsibility for
any errors or omissions that may appear in this documentation.
With respect to the contents of this documentation, ASRock does not provide
warranty of any kind, either expressed or implied, including but not limited to
the implied warranties or conditions of merchantability or fitness for a particular
purpose.
In no event shall ASRock, its directors, officers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of profits, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the documentation or product.
The terms HDMI™ and HDMI High-Definition Multimedia Interface, and the HDMI
logo are trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Chapter 1 Introduction 1
1.1 Package Contents 1
1.2 Specifications 2
Chapter 2 Installation 8
2.1 Installing Memory Modules (SO-DIMM) 9
3.2 A-Tuning 18
3.5 Start8 35
4.4 Tools 51
Chapter 1 Introduction
Thank you for purchasing ASRock Q1900B-ITX/D1800B-ITX motherboard, a
reliable motherboard produced under ASRock’s consistently stringent quality
control. It delivers excellent performance with robust design conforming to
ASRock’s commitment to quality and endurance.
Because the motherboard specifications and the BIOS software might be updated, the
content of this documentation will be subject to change without notice. In case any modi-
fications of this documentation occur, the updated version will be available on ASRock’s
website without further notice. If you require technical support related to this mother-
board, please visit our website for specific information about the model you are using. You
may find the latest VGA cards and CPU support list on ASRock’s website as well. ASRock
website http://www.asrock.com.
English
1
1.2 Specifications
2
Q1900B-ITX/D1800B-ITX
3
BIOS • 64Mb AMI UEFI Legal BIOS with GUI support
Feature • Supports Plug and Play
• ACPI 1.1 compliant wake up events
• Supports jumperfree
• SMBIOS 2.3.1 support
Due to limitation, the actual memory size may be less than 4GB for the reservation for
system usage under Windows® 32-bit operating systems. Windows® 64-bit operating systems
do not have such limitations. You can use ASRock XFast RAM to utilize the memory that
Windows® cannot use.
English
4
Q1900B-ITX/D1800B-ITX
1 2
Keyboard
Mouse
PS2
PS2
CPU_FAN1
64Mb
BIOS
DDR3_A1
3
TPMS1
1
COM1
PARALLEL PORT
Super
I/O
DDR3_B1
VGA1
ATXPWR1
4
RoHS
USB 2.0
HDMI
D1800B-ITX
T: USB0
B: USB1
USB 3.0
USB 2.0
Top:
USB3
USB2
USB4_5
RJ-45 5
1
USB 3.0
MIC IN
Bottom:
LINE IN
Top:
FRONT
Center:
SATA2_ 1
SATA2_2
HD_AUDIO1
CMOS
1 Battery SPEAKER1
1 6
COM2
PLED PWRBTN
SPEAKER2
AUDIO
CODEC
CLRCMOS1
1
CI1
1
1
7
1 HDLED RESET
PANEL1
1 PCIE1
15 14 13 12 11 10 9 8
English
5
No. Description
1 TPM Header (TPMS1)
2 CPU Fan Connector (CPU_FAN1)
3 2 x 204-pin DDR3/DDR3L SO-DIMM Slots (DDR3_A1, DDR3_B1)
4 ATX Power Connector (ATXPWR1)
5 USB 2.0 Header (USB4_5)
6 Chassis Speaker Header (SPEAKER1)
7 System Panel Header (PANEL1)
8 SATA2 Connector (SATA2_1)
9 COM Port Header (COM2)
10 SATA2 Connector (SATA2_2)
11 Chassis Fan Connector (CHA_FAN1)
12 Chassis Intrusion Header (CI1)
13 Clear CMOS Jumper (CLRCMOS1)
14 Front Panel Audio Header (HD_AUDIO1)
15 3W Audio AMP Output Wafer Header (SPEAKER2)
English
6
Q1900B-ITX/D1800B-ITX
13 12 11 10 8 7
9
* There are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications.
ACT/LINK LED
SPEED LED
LAN Port
7
Chapter 2 Installation
This is an Mini-ITX form factor motherboard. Before you install the motherboard,
study the configuration of your chassis to ensure that the motherboard fits into it.
Pre-installation Precautions
Take note of the following precautions before you install motherboard components
or change any motherboard settings.
• Make sure to unplug the power cord before installing or removing the motherboard.
Failure to do so may cause physical injuries to you and damages to motherboard
components.
• In order to avoid damage from static electricity to the motherboard’s components,
NEVER place your motherboard directly on a carpet. Also remember to use a grounded
wrist strap or touch a safety grounded object before you handle the components.
• Hold components by the edges and do not touch the ICs.
• Whenever you uninstall any components, place them on a grounded anti-static pad or
in the bag that comes with the components.
• When placing screws to secure the motherboard to the chassis, please do not over-
tighten the screws! Doing so may damage the motherboard.
English
8
Q1900B-ITX/D1800B-ITX
The SO-DIMM only fits in one correct orientation. It will cause permanent damage
to the motherboard and the SO-DIMM if you force the SO-DIMM into the slot at
incorrect orientation.
English
9
3
2
1
10
English
Q1900B-ITX/D1800B-ITX
Before installing an expansion card, please make sure that the power supply is switched off
or the power cord is unplugged. Please read the documentation of the expansion card and
make necessary hardware settings for the card before you start the installation.
PCIe slots:
PCIE1 (PCIe 2.0 x1 slot) is used for PCI Express cards with x1 lane width cards.
English
11
2.3 Jumpers Setup
The illustration shows how jumpers are setup. When the jumper cap is placed on
the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper
is “Open”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short”
when a jumper cap is placed on these 2 pins.
CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the system
parameters to default setup, please turn off the computer and unplug the power
cord from the power supply. After waiting for 15 seconds, use a jumper cap to
short pin2 and pin3 on CLRCMOS1 for 5 seconds. However, please do not clear
the CMOS right after you update the BIOS. If you need to clear the CMOS when
you just finish updating the BIOS, you must boot up the system first, and then shut
it down before you do the clear-CMOS action. Please be noted that the password,
date, time, and user default profile will be cleared only if the CMOS battery is
removed.
If you clear the CMOS, the case open may be detected. Please adjust the BIOS option “Clear
Status” to clear the record of previous chassis intrusion status.
English
12
Q1900B-ITX/D1800B-ITX
Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these
headers and connectors. Placing jumper caps over the headers and connectors will cause
permanent damage to the motherboard.
The front panel design may differ by chassis. A front panel module mainly consists of power
switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connect-
ing your chassis front panel module to this header, make sure the wire assignments and the
pin assignments are matched correctly.
English
13
Serial ATA2 Connectors SATA2_1 These two SATA2
(SATA2_1: connectors support SATA
see p.7, No. 8) SATA2_2 data cables for internal
(SATA2_2: storage devices with up to
see p.7, No. 10) 3.0 Gb/s data transfer rate.
GND
Front Panel Audio Header PRESENCE# This header is for
MIC_RET
(9-pin HD_AUDIO1) OUT_RET connecting audio devices
(see p.7, No. 14) to the front audio panel.
1
OUT2_L
J_SENSE
OUT2_R
MIC2_R
MIC2_L
1. High Definition Audio supports Jack Sensing, but the panel wire on the chassis must sup-
port HDA to function correctly. Please follow the instructions in our manual and chassis
manual to install your system.
2. If you use an AC’97 audio panel, please install it to the front panel audio header by the
steps below:
A. Connect Mic_IN (MIC) to MIC2_L.
B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.
C. Connect Ground (GND) to Ground (GND).
D. MIC_RET and OUT_RET are for the HD audio panel only. You don’t need to connect
them for the AC’97 audio panel.
E. To activate the front mic, go to the “FrontMic” Tab in the Realtek Control panel and
adjust “Recording Volume”.
Front_R-
Wafer Header Front_R+ speaker to this header.
(4-pin SPEAKER2) Front_L+
Front_L-
(see p.7, No. 15)
1
14
Q1900B-ITX/D1800B-ITX
S_PWRDWN#
F_CLKRUN#
GND
LAD3_L
LFRAME#_L
TPM_RST#
+3V
LAD0_L
+3VSB
GND
15
Serial Port Header RRXD1
DDTR#1 This COM2 header
DDSR#1
(9-pin COM2) CCTS#1 supports a serial port
(see p.7, No. 9) 1
module.
RRI#1
RRTS#1
GND
TTXD1
DDCD#1
English
16
Q1900B-ITX/D1800B-ITX
Drivers Menu
The drivers compatible to your system will be auto-detected and listed on the
support CD driver page. Please click Install All or follow the order from top to
bottom to install those required drivers. Therefore, the drivers you install can work
properly.
Utilities Menu
The Utilities Menu shows the application software that the motherboard supports.
Click on a specific item then follow the installation wizard to install it.
To improve Windows 7 compatibility, please download and install the following hot fix
provided by Microsoft.
“KB2720599”: http://support.microsoft.com/kb/2720599/en-us
English
17
3.2 A-Tuning
A-Tuning is ASRock’s multi purpose software suite with a new interface, more new
features and improved utilities, including XFast RAM and a whole lot more.
Operation Mode
Choose an operation mode for your computer.
English
18
Q1900B-ITX/D1800B-ITX
Tools
Various tools and utilities.
XFast RAM
Boost the system’s performance and extend the HDD’s or SDD’s lifespan! Create a
hidden partition, then assign which files should be stored in the RAM drive.
FAN-Tastic Tuning
Configure up to five different fan speeds using the graph. The fans will automatically
shift to the next speed level when the assigned temperature is met.
English
19
3.3 Intel® Smart Connect Technology
Intel® Smart Connect Technology is a feature that periodically wakes your computer
from Windows® sleep state to refresh email or social networking applications. It
saves your waiting time and keeps the content always up-to-date.
• Set the SATA mode to AHCI. If Windows 8/7 is already installed under IDE
mode, directly changing the SATA mode to AHCI may cause Windows 8/7
to crash while booting. If your system is not in AHCI mode, please follow the
instructions below.
There are certain risks. Please backup any important data before operating to avoid loss.
1. Press Win + R simultaneously in Windows 8/7, type "Regedit" into the word
box then click OK.
20
Q1900B-ITX/D1800B-ITX
Step 2
Once installed, run ASRock Smart Connect from your desktop or go to Windows
Start -> All Programs -> ASRock Utility. English
21
Step 3
Click the Add button. Take Foxmail as an example, add Foxmail to the Application
list.
Step 4
Select Foxmail from the Application List, then click the arrow pointing right to add
this application to the Smart Connect List.
Step 5
English
22
Q1900B-ITX/D1800B-ITX
Step 6
Double-click the Intel® Smart Connect Technology Manager icon in the
Windows system tray.
Step 7
Drag the slider to configure how often the system will connect to the network to
download updates. Shorter durations will provide more frequent updates, but may
cause more power consumption.
2. Click on Windows Start -> the arrow next to Shut down, and click on Sleep.
English
23
4. The system will wake up from sleep state periodically, and then start to update
Foxmail. The screen will not display anything so the computer can maintain
minimum power usage. Afterwards, the system will automatically return to
sleep state again.
5. Upon waking up the system, you will find the new mail that were sent to you
during sleep state are already updated and ready to be read in Foxmail.
English
24
Q1900B-ITX/D1800B-ITX
Have you ever been in a situation where you emergently needed certain files in your
computer, however the computer was gazillion miles away out of reach? ASRock Cloud
includes several technologies and software solutions for remotely controlling your
computer, even if the computer is in off mode. For ASRock motherboards with a Realtek®
LAN chip, ASRock Cloud allows users to remotely wake up their computers via the
internet by using a secondary device, such as a smartphone or tablet. Users may use
Kloudian® Orbweb.ME Professional to remotely wake up and control their computers, or
they could wake up the computer then use any other preferred remote desktop application.
This motherboard supports Wake-On-WAN with the onboard Realtek® LAN, so you can
connect with your PC from anywhere in the world. You will be able to power your PC on
English
or turn it off, monitor and take control of it remotely with another smartphone, tablet or
computer.
*ASRock Cloud is supported on Windows 8.1 or Windows 7.
25
3.4.1 Realtek® Wake-On-WAN
Realtek® Wake-On-WAN allows you to wake up and remote control your home computer
from sleep or shutdown state.
Before configuring this feature, verify the followings on your host computer:
• Make sure that the "PCIE Devices Power On" is enabled in UEFI SETUP
UTILITY > Advanced > ACPI Configuration.
*The UEFI screen is for reference only. The actual screen may differ by model.
• Make sure that the "Shutdown Wake-On-Lan" is enabled in Device Manager >
Network Adapters > Realtek PCIe GBE Family Controller > Advanced.
*The screen is for reference only. The actual screen may differ on different computers.
English
26
Q1900B-ITX/D1800B-ITX
Step 1
Step 2
Step 3
Step 1
On the Orbweb.ME Portal login page, click Sign Up to create an Orbweb.ME account and
name your host computer.
English
27
Step 3
You will receive a verification email. Follow the steps in the email to verify your account.
After verifying your account, you can access your PC through web browsers at
http://orbweb.me.
On the Account Verified page, if you click Go to My Computers, you will see the Orbweb.
ME portal page as a client.
Step 1
Or, if you just finished signing up for your host computer, you can click Configure this
computer in the screen to begin.
Step 2
Click Folder Settings tab and the default shared folders display.
To add a folder, click . Select a folder to add it into Orbweb.ME. Then click Save.
English
You can access the documents in these shared folders on the host computer remotely
through Xplorer from your client device.
28
Q1900B-ITX/D1800B-ITX
The lastest version of Java is required to be installed to use the Remote Desktop and
Xplorer functions.
Remote Wake-Up allows you to remotely put your host computer to sleep and wake your
host computer up from a client device.
If you use a motherboard with dual LAN ports, please disable one of the LAN ports
to use the Remote Wake-Up function. To do so, go to Control Panel > Network and
Sharing Center > Manage Network Connections, right-click Local Area Connections
and select Disable.
Step 1
Go to Orbweb.ME portal login page: http://orbweb.me
Step 2
Log in with your Orbweb.ME account and password.
Step 3
Find the host computer from the list by the computer name you give.
29
Step 4
Click and power options appear. Click to select Restart, Sleep or Shut Down.
Select Restart from the options to restart your host computer remotely.
When you select Sleep or Shut Down, if the host device is WOW(Wake-On-Wan)
compatible, you can put your host computer to sleep (S3/S4) or shut down your host
computer (S5) remotely. The host status in the Status column shows offline and ready to be
awaked and the power option shows wakable .
To wake up the computer, click .
Please be noted that if the host device is not WOW compatible, the host status icon
will turn offline and the power option icon will disappear. You have to physically
wake up computer in order to bring power option icon back to online.
Step 3
30
Q1900B-ITX/D1800B-ITX
Please be noted that if the host device is not WOW compatible, the host status icon
will turn offline and the power option icon will dissappear. You have to physically
wake up computer in order to bring power option icon back to online.
Remote Desktop allows you to remotely access your host computer from a client device.
Step 2
Log in with your Orbweb.ME account and password.
Step 3
Step 5
Enter the Windows password to log in and you will see the desktop of your host computer.
Please refer to the user manual of the Kloudian® Orbweb.ME Professional for more
instructions on how to use Orbweb.ME Professional.
English
31
For iOS or Android Mobile Devices users:
Download and install “Orbweb.ME Professional” app from the App Store (iOS) or Play
Store (Android).
Step 1
Step 2
Log in with your Orbweb.ME account and password.
Step 3
Tap the host computer name that you want to access under the Remote Desktop section.
Step 4
Enter the Windows password to log in and you will see the desktop of your host computer.
English
32
Q1900B-ITX/D1800B-ITX
Using Xplorer
Xplorer allows you to remotely access documents on your host computer from a client
device.
Step 2
Log in with your Orbweb.ME account and password.
Step 3
Step 5
Root directory displays. Click on a folder name to open the folder.
Step 6
Click on a file name to preivew the file.
English
You can also delete, rename, move, and copy a selected file. For more instructions on how
to use Xplorer, refer to the user manual of the Kloudian® Orbweb.ME Professional.
33
For iOS or Android Mobile Devices users:
Download and install “Orbweb.ME Professional” app from the App Store (iOS) or Play
Store (Android).
Step 1
Step 3
You can also delete, rename, move, and copy a selected file. For more instructions
on how to use Xplorer, refer to the user manual of the Kloudian® Orbweb.ME
Professional.
English
Tutorial Video
34
Q1900B-ITX/D1800B-ITX
3.5 Start8
For those Windows 8 users who miss the Start Menu, Start8 is an ideal solution that
brings back the familiar Start Menu along with added customizations for greater
efficiency.
Select between the Windows 7 style and Windows 8 style Start Menu. Then select
the theme of the Start Menu and customize the style of the Start icon.
English
35
Configure
Configure provides configuration options, including icon sizes, which shortcuts you
want Start Menu to display, quick access to recently used apps, the functionality of
the power button, and more.
Control
English
36
Q1900B-ITX/D1800B-ITX
Control lets you configure what a click on the start button or a press on the
Windows key does.
Desktop
Desktop allows you to disable the hot corners when you are working on the desktop.
It also lets you choose whether or not the system boots directly into desktop mode
and bypass the Metro user interface.
About
Displays information about Start8. English
37
Chapter 4 UEFI SETUP UTILITY
4.1 Introduction
ASRock Interactive UEFI is a blend of system configuration tools, cool sound effects
and stunning visuals. Not only will it make BIOS setup less difficult but also a lot
more amusing. This section explains how to use the UEFI SETUP UTILITY to
configure your system. You may run the UEFI SETUP UTILITY by pressing <F2>
or <Del> right after you power on the computer, otherwise, the Power-On-Self-Test
(POST) will continue with its test routines. If you wish to enter the UEFI SETUP
UTILITY after POST, restart the system by pressing <Ctl> + <Alt> + <Delete>, or
by pressing the reset button on the system chassis. You may also restart by turning
the system off and then back on.
Because the UEFI software is constantly being updated, the following UEFI setup screens
and descriptions are for reference purpose only, and they may not exactly match what you
see on your screen.
38
Q1900B-ITX/D1800B-ITX
Please check the following table for the descriptions of each navigation key.
39
4.2 Main Screen
When you enter the UEFI SETUP UTILITY, the Main screen will appear and
display the system overview.
Q1900B-ITX:
D1800B-ITX:
English
40
Q1900B-ITX/D1800B-ITX
Setting wrong values in this section may cause the system to malfunction.
English
41
4.3.1 CPU Configuration
42
Q1900B-ITX/D1800B-ITX
DRAM Voltage
Use this to configure DRAM Voltage. The default value is [Auto].
Share Memory
Configure the size of memory that is allocated to the integrated graphics processor
when the system boots up.
Onboard HD Audio
Enable/disable onboard HD audio. Set to Auto to enable onboard HD audio and
automatically disable it when a sound card is installed.
Front Panel
Enable/disable front panel HD audio.
43
Onboard LAN
Enable or disable the onboard network interface controller.
Deep S5
Configure deep sleep mode for power saving when the computer is shut down.
44
Q1900B-ITX/D1800B-ITX
SATA Controller(s)
Enable/disable the SATA controllers.
AHCI (Advanced Host Controller Interface) supports NCQ and other new features that
will improve SATA disk performance but IDE mode does not have these advantages.
45
4.3.4 Intel® Smart Connect Technology
46
Q1900B-ITX/D1800B-ITX
Serial Port 1
Enable or disable the Serial port 1.
Serial Port 2
Enable or disable the Serial port 2.
Parallel Port
Enable or disable the Parallel port.
Change Settings
Select the address of the Parallel port.
English
Device Mode
Select the device mode according to your connected device.
47
4.3.6 ACPI Configuration
Suspend to RAM
Select disable for ACPI suspend type S1. It is recommended to select auto for ACPI
S3 power saving.
Ring-In Power On
Allow the system to be waked up by onboard COM port modem Ring-In signals.
Allow the system to be waked up by the real time clock alarm. Set it to By OS to let
it be handled by your operating system.
48
Q1900B-ITX/D1800B-ITX
English
49
4.3.7 USB Configuration
USB Controller
Enable or disable all the USB ports.
50
Q1900B-ITX/D1800B-ITX
4.4 Tools
Instant Flash
Save UEFI files in your USB storage device and run Instant Flash to update your
UEFI.
Internet Flash
ASRock Internet Flash downloads and updates the latest UEFI firmware version
from our servers for you. Please setup network configuration before using Internet
Flash.
*For BIOS backup and recovery purpose, it is recommended to plug in your USB
pen drive before using this function.
English
51
Network Configuration
Use this to configure internet connection settings for Internet Flash.
Internet Setting
Select an internet connection mode.
52
Q1900B-ITX/D1800B-ITX
53
4.6 Boot Screen
This section displays the available devices on your system for you to configure the
boot settings and the boot priority.
Fast Boot
Fast Boot minimizes your computer's boot time. In fast mode you may not boot
from an USB storage device. Ultra Fast mode is only supported by Windows 8 and
the VBIOS must support UEFI GOP if you are using an external graphics card.
Please notice that Ultra Fast mode will boot so fast that the only way to enter this
UEFI Setup Utility is to Clear CMOS or run the Restart to UEFI utility in Windows.
Bootup Num-Lock
Select whether Num Lock should be turned on or off when the system boots up.
Boot Beep
English
Select whether the Boot Beep should be turned on or off when the system boots up. Please
note that a buzzer is needed.
54
Q1900B-ITX/D1800B-ITX
CSM
Enable to launch the Compatibility Support Module. Please do not disable unless
you’re running a WHCK test. If you are using Windows 8 64-bit and all of your
devices support UEFI, you may also disable CSM for faster boot speed.
English
55
4.7 Security Screen
In this section you may set or change the supervisor/user password for the system.
You may also clear the user password.
Supervisor Password
Set or change the password for the administrator account. Only the administrator
has authority to change the settings in the UEFI Setup Utility. Leave it blank and
press enter to remove the password.
User Password
Set or change the password for the user account. Users are unable to change the
settings in the UEFI Setup Utility. Leave it blank and press enter to remove the
password.
Secure Boot
Enable to support Windows 8 Secure Boot.
English
56
Q1900B-ITX/D1800B-ITX
Discard Changes
When you select this option the following message, “Discard changes?” will pop
out. Select [OK] to discard all changes.
57
Contact Information
If you need to contact ASRock or want to know more about ASRock, you’re welcome
to visit ASRock’s website at http://www.asrock.com; or you may contact your dealer
for further information. For technical questions, please submit a support request
form at http://www.asrock.com/support/tsd.asp
ASRock Incorporation
2F., No.37, Sec. 2, Jhongyang S. Rd., Beitou District,
6604 LV Wijchen
The Netherlands
Phone: +31-24-345-44-33
Fax: +31-24-345-44-38
U.S.A.
Phone: +1-909-590-8308
Fax: +1-909-590-1026
English
58