Professional Documents
Culture Documents
C Band VSAT Data Communication System An
C Band VSAT Data Communication System An
3, May 2012
KEYWORDS
BER, Convolutional codes, Link budget, Satellite Communication, VSAT.
I. INTRODUCTION
This paper is concerned with VSAT (Very Small Aperture Terminal), VSAT is a main
communication media for Karnataka Power Transmission Corporation Limited (KPTCL)/
ESCOM (Electric supply companies)Supervisory Control And Data Acquisition (SCADA)
network and it also provides voice communication to all KPTCL, ESCOMS stations, and major
generating stations with load dispatch centre (LDC). Implementation deals with the modelling
and simulation of RF communications link involving satellite transponder. A transponder is the
series of interconnected units forming an RF (Radio Frequency) broadband communication
channel between the receiver and transmit antenna in a communication satellite. The typical
extended C-band communications satellite will be examined briefly here. Each transponder is
amplified by either a travelling wave tube amplifier (TWTA) or a solid state power amplifier
(SSPA). Satellites of this are type are very popular for transmitting TV channels to broadcast
stations, cable TV systems (DTH) direct to home systems. other applications include Very small
aperture terminal (VSAT) data communications network, Integration of these information type
is becoming popular as Satellite transponders, can deliver data rates in the range of 1000Kbps
to 256 Mbps. Achieving these high data rates require careful consideration of the design and
performance of the repeater. The methodology, adopted here is QAM technique and software-
tool is Math works with simulink to explore the end to end simulation of communication links
involving satellite transponder.
Fig1shows the block diagram of basic VSAT satellite communication system. Satellite
communication system consists of many earth stations on the ground and these are linked with a
satellite in space. The user is connected to the Earth station through a terrestrial network and
DOI : 10.5121/ijdps.2012.3328 339
International Journal of Distributed and Parallel Systems (IJDPS) Vol.3, No.3, May 2012
this terrestrial network may be a telephone switch or dedicated link to earth station. The user
generates a baseband signal that is processed through a terrestrial network and transmitted to a
satellite at the earth station. The satellite transponder consists of a large number of repeaters in
space, receives the modulated RF carrier in its uplink frequency spectrum from all the earth
station in the network, amplifies these carriers and retransmits them back to the earth stations in
the downlink frequency spectrum. To avoid the interference, downlink spectrum should be
different from uplink frequency spectrum. The signal at the receiving earth station is processed
to get back the baseband signal, it is sent to the user through a terrestrial network.
Satellite Transponder
TX RX
Users Users
340
International Journal of Distributed and Parallel Systems (IJDPS) Vol.3, No.3, May 2012
RX Antenna
The signal received from the satellite is processed through LNA (Low Noise Amplifier) then it
is down-converted, and demodulated. Thus the original baseband signal is obtained.
II. VSAT
The acronym VSAT stands for Very Small Aperture Terminal is the earth station antenna used
at the VSAT earth stations. In VSAT the earth station antenna size is typically less than 2.4 m in
diameter and the trend is towards even smaller dishes not more than 1.8 m in diameter.
According to European Telecommunication standard Institute, VSAT is referred as satellite
transmit –receive system that has an aperture size smaller than 2.8m2. VSAT’s provide cost
effective solutions for the growing telecommunication needs through -out the world. Today’s
satellites are more powerful, enabling the use of smaller and less-expensive antennas on the
ground. Also, the developments include most of the necessary VSAT functions, which makes
VSATs more effective.
The architecture of the networks is of two types. One is star topology and the other is mesh
topology. The star topology is the traditional VSAT network topology, here the communication
link are between the hub and the remote terminal. This topology is well suited for data
broadcasting or data collection. This is not applicable for speech services because the time delay
is too severe (500ms). The access techniques used in a star network can be both FDMA and
341
International Journal of Distributed and Parallel Systems (IJDPS) Vol.3, No.3, May 2012
TDMA. In mesh topology there is a direct communication between the remote VSAT terminals.
This minimizes the time delay which is concerned with speech services. The access method
used in a mesh network is FDMA. Very Small Aperture Terminals (VSATs) are designed for
data transmission and distribution over a wide geographical area amongst a large number of
locations. The small size and low transmit power of a VSAT station are the factors that keep the
price of the earth station at a level that makes a VSAT network an economic alternative to a
terrestrial data network using telephones lines and modems. The hub usually houses a central
host computer, which can act as a data switching centre. The architecture of the network
naturally becomes star shaped, [Maral, 1995]. The links from the hub to the VSAT are called
outbound links. The links from the VSAT to the hub are called inbound links. Both inbound and
outbound links consist of two parts, uplink and downlink. It is not unusual that inbound and
outbound links operate at different transmission speeds, i.e. in asymmetrical mode.
342
International Journal of Distributed and Parallel Systems (IJDPS) Vol.3, No.3, May 2012
1. Bernoulli Binary generator: This block generates random binary numbers using
Bernoulli binary distribution. Data signal generates a stream of information bits to be
transmitted by the transmitter, specifically Bernoulli binary generator is employed as a
data signal generator.
3. Raised Cosine Transmit Filter: The Raised Cosine Transmit Filter block up
samples and filters the input signal using a normal raised cosine FIR filter or a square
root raised cosine FIR filter.
Functional block Parameters -
• Filter type : Square root
• Roll off factor : 0.2
• Up sampling factor: 8
4 High Power Amplifier: Satellite links have a limited power available to them. Efficient
amplifiers are necessary to use this power carefully, so high power amplifiers are used.
Travelling wave tube amplifier (TWTA) is used to amplify radio frequency signals to
high power. Model of a travelling wave tube amplifier (TWTA) using the Saleh model
is used. The saleh model provides an independent gain and phase function that has been
used to compute output wave-form for given input which is not available in other high
power amplifications.
Functional block parameters -
• input scaling factor: –16.1821
• AM/AM parameters [alpha beta] : [2.1587 1.1517]
• AM/PM parameters[alpha beta] : [4.0033 9.1040]
• Output scaling factor: 32.9118
5 Gain (Tx. Dish Antenna Gain): This block models the gain of the transmitting
parabolic dish antenna on the satellite. A parabolic antenna is an antenna that uses a
parabolic reflector, a surface with the cross-sectional shape of a parabola, to direct the
radio waves. The main advantage of the parabolic antenna is that it is highly directive.
Gain = 52.48 dB
343
International Journal of Distributed and Parallel Systems (IJDPS) Vol.3, No.3, May 2012
Simulink model of RF satellite transponder subsystem is shown in Fig 6. Following are the
components of the RF satellite link subsystem:
1. Uplink path: Uplink connects transmit earth station to satellite. Free Space Path Loss
is the major loss that can occur during transmission to satellite. So Free Space Path Loss
block is used to model this loss. This block aattenuates the signal by the free space path
loss.
Uplink free space loss: 221 dB
3. Downlink path: Downlink connects satellite to the receive earth station. In addition
free space path loss Doppler and phase errors are also modeled in this path. Free Space
Path Loss block attenuates the signal. Phase / Frequency Offset block rotates the signal
to model phase and Doppler error on the link.
Downlink path loss: 217dB
Lower half of fig 5 shows the model of Receiver Earth Station subsystem. Following are the
components of the receiver earth station subsystem:
1. Gain (Rx. Dish Antenna Gain) : This block models the gain of the receiver dish
antenna( feed prime focus antenna used in VSATs)
Gain = 36.85 dB
2. Receiver Thermal Noise: This block adds noise that represents the effective system
temperature of the receiver.
Functional block parameters:
Specification method: Noise temperature
344
International Journal of Distributed and Parallel Systems (IJDPS) Vol.3, No.3, May 2012
3. I/Q imbalance: In I/Q (In phase/Quadrature phase) processing receivers, matching the
amplitudes and phases of the I and Q branches is of major concern. In practice,
matching can never be perfect in the analog front-end which results in insufficient
rejection of the image frequency band. I/Q imbalance block is used to model this effect.
This block creates a complex baseband model of signal impairments caused by
imbalances between in-phase and quadrature receiver and aplies an in-phase dc offset,
specified by the I dc offset parameter, and a quadrature offset, specified by the Q dc
offset parameter, to the signal.
DC offset compensation: This block is built to estimate and remove the DC offset
from the signal. It compensates for the DC offset in the I/Q Imbalance block.
4. Automatic Gain Control: The role of the AGC circuit is to provide relatively
constant output amplitude so that circuits following the AGC circuit require less
dynamic range. If the signal level changes are much slower than the information rate
contained in the signal, then an AGC circuit can be used to provide a signal with a well
defined average level to downstream circuits. It is an adaptive system whose average
output signal level is fed back to adjust the gain to an appropriate level for a range of
input signal levels. For example, without AGC the sound emitted from an AM radio
receiver would vary to an extreme extent from a weak to a strong signal; the AGC
effectively reduces the volume if the signal is strong and raises it when it is weaker.
AGC algorithms often use a PID controller where the P term is driven by the error
between expected and actual output amplitude.
6. Raised Cosine Receive Filter: This block applies a matched filter to the modulated
signal using the square root raised cosine pulse shape.
8. Sink: The sink is the BER estimate section, which compares a transmitted data stream
345
International Journal of Distributed and Parallel Systems (IJDPS) Vol.3, No.3, May 2012
with a receive data stream to calculate the Bit error rate of a system. It also outputs the
number of error events that have occurred, and the total number of bits or symbols
compared.
The transponder is a central element in the end-to-end communication link and is one of
the elements in overall performance. There the transmitting earth –station on the up-link
side will cause its share of distortion, as will the receiving earth station on the downlink
side. To obtain maximum power output with the highest efficiency, the amplifier should
be operated at its saturation point. Which produce, AM / AM and AM / PM
conversation. The next significant impairments to digital transmission are from the
filters, which constraints bandwidth and introduce delay distortion. Simple link
budgeting techniques are available for evaluating links with noise.
Table 1 gives the data’s of KPTCL which is used in developing the model.
Pr = (1)
346
International Journal of Distributed and Parallel Systems (IJDPS) Vol.3, No.3, May 2012
Where Pr is power received by the receiving antenna: Pt is the power applied to the transmitting
antenna: G t is the gain of the transmitting antenna, Gr is gain of the receiving antenna, C is the
speed of light (c = 3 x 10 8 m/s): R is the range (path length) in meters: and f is the frequency in
hertz .Almost all link calculations are performed after converting from products and ratios to
decibels. This uses the unit popular unit of decibels, thus converting the equation (1) into
decibels, has the form of a power balance as Pr = Pt + Gt + Gr –Path-loss
All link budgets require knowledge of the free space path loss between the earth station and the
satellite and the noise powers in the operating bandwidth.
The Parameters:
• Distance = 37000 km
• Uplink Frequency = 6946 MHz
• Downlink frequency = 4721 MHz
Gain (Tx and Rx. Dish Antenna Gain): Gain of the antenna is given by -
G= = (π D/λ) 2 (3)
Where is the antenna efficiency, A is the effective area, and λ is the wavelength.
Table 2 and Table 3 helps in the calculation of Transmitter and Receiver Antenna Gains
The maximum VSAT Antenna Gain for uplink was found by taking the maximum carrier
frequency into account as per Table 1. And VSAT Antenna Gain for downlink was obtained
by taking the maximum carrier frequency as shown below.
347
International Journal of Distributed and Parallel Systems (IJDPS) Vol.3, No.3, May 2012
All signal sources in the signal processing and communication‘s can generate frame based data.
In this work, the signal is frame based and samples are propagated through a model and
multiple samples are processed in batches. Frame – based processing takes advantage of
Simulink matrix processing capabilities to reduce overhead. Complex modulation scheme are
best viewed using a scatter diagram. The scatter diagram allows us to visualize the real and
imaginary (in-phase and quadrature) component of the complex signal. Thus Fig.7 shows the
Scatter plot of VSAT _Satellite system in the transmitter and Fig.8 shows the Scatter plot of
VSAT _ satellite system showing the effect of phase offset. Fig 9 shows the receiver
constellation with frequency offset, and fig 10 shows VSAT _satellite received constellation
after RF corrected Impairments.
348
International Journal of Distributed and Parallel Systems (IJDPS) Vol.3, No.3, May 2012
349
International Journal of Distributed and Parallel Systems (IJDPS) Vol.3, No.3, May 2012
350
International Journal of Distributed and Parallel Systems (IJDPS) Vol.3, No.3, May 2012
351
International Journal of Distributed and Parallel Systems (IJDPS) Vol.3, No.3, May 2012
352
International Journal of Distributed and Parallel Systems (IJDPS) Vol.3, No.3, May 2012
Spectrum diagram
Fig11 shows the spectrum of the modulated / transmitted signal has indicated in red colour and
the received signal as shown in blue colour. Both spectrums are almost similar but some effects
of thermal noise caused by the Receiver thermal noise block can be seen in the receiver signal
Spectrum.
353
International Journal of Distributed and Parallel Systems (IJDPS) Vol.3, No.3, May 2012
BER Estimation
Bit Error Rate calculator block compares the Data transmitted message with the
received data message and displays the error as BER as shown below.
To overcome these two BER values, a compensation of phase /frequency offset is added
in the receiver section and the constellation of such correction is visualized in Fig.10.
The final BER values after performing phase/frequency compensation are obtained as
shown below.
Conclusion
The results can be concluded by comparing the three analysis of simulated results.
The first analysis of the case study exhibits the effect of Phase/Frequency offset. Whose values
are high without compensation block.
Fig. 8 shows the constellation diagram at the Receiver before phase and frequency correction.
where there is a phase tilt of 15 degrees andig. 9 shows the effect of frequency of 2 Hz. These
distorted signals can be corrected by using phase/frequency compensation network.
Thus the second analysis of the case study exhibits the BER = 0.00052, .whose value is desired
by considering the effect of phase/frequency offset after passing through satellite Transponder.
As shown in fig 10.
.
The third analysis shows receiver spectrum diagram which gives the effect of thermal noise as
indicated by two colours, red colour indicates transmitted signal and blue colour caused by
receiver thermal noise block.
Thus Table 1 to 3 gives the satellite parameters of load dispatching centre of Karnataka Power
system at Bangalore. Where the same values have been implemented in the model to simulate
the BER results whose values exceeds 10-3 in analysis 1 and the values can be further corrected
by using compensation circuit.
Acknowledgments
The authors are very grateful to the Management of Vidya vardhaka College of Engineering,
Mysore, Karnataka, India. The National Institute of Engineering, Mysore, Karnataka, India.
354
International Journal of Distributed and Parallel Systems (IJDPS) Vol.3, No.3, May 2012
REFERENCES
[1] XiaolongLi, “ Simulink – based Simulation of quadrature amplitude Modulation (QAM)
System”, Proceedings of the 2008 IAJC – IJME, International Conference
[2] Bruce Elbert, “ Simulating the Performance of Communication Links with Satellite
Transponders” Application Technology Strategy, Inc.
[3] M.H. Hadjitheodosiou, Frances P. Coakley and Barry G. Evans, “Next Generation Multiiservice
VSAT Networks” July 2, 1997.
[4] T. Pratt, C . Bostian , J.Allnutt, "Satellite Communication” John Wiley and Sons, 2nd
Edition.
[5] Theodore S. Rappaport, ”Wireless Communications” , Principles and Practice, Prentice – Hall
of India Private Limited, 2nd Edition.
[6] Sanjay Sharma “Wireless and Cellular Communications”, S.K. Kataria and Sons 2nd edition,
Jan 2007.
[8] Ersin Aras “ Analysis of Jammer Resistant, Spread Spectrum, VSAT Communication scheme
for maritime platform using DS-CDMA” , MS in System Engineering, from Naval Postgraduate
School, September 2002.
Authors
T.P. Surekha, received the B.E degree from Mangalore University, Mangalore. And M.Tech degree
from Visvesvaraya Technological University, Belgaum. Presently she is working as Associate professor
in the department of Electronics and Communication Engineering, Vidyavardhaka College of
Engineering, Mysore. Her research interest include Power-line communication System, Automation and
Simulation of Communication System in Power System. Modeling and Simulation of Communication
systems.
T. Ananthapadmanabha received the B.E. degree, M.Tech degree and Ph.D. degree from the University of
Mysore, Mysore. Presently, he is working as Professor and Head in the Department of Electrical
Engineering, The National Institute of Engineering, Mysore. He is also Honorary Secretary of Institute of
Engineers, (India), Mysore Local Centre, Mysore. His research interest include voltage stability,
distribution automation and AI applications in power system. Simulation of Power and Communication
System.
C Puttamadappa, received the B.E degree from Mysore University, Mysore. And M. E degree from
Bangalore University, Bangalore. Ph.D degree from Jadvapur University, Kolkatta. Presently he is
working as professor in the department of Electronics and Communication Engineering, Sapthagiri
college of Engineering, Bangalore, His research interest include Power Electronics, Simulation of
communication systems, and Mobile Wireless Networks.
355