Professional Documents
Culture Documents
that has been entered in Program- terminal 3.
ming Blocks. 4. Apply power to the GEM-P800
DEALER PROGRAM MODE - KEYPAD KEY DEFINITION control panel.
5. After a few seconds the ARMED,
NOTE: READY and SYSTEM TROU-
Blank Key
After 15 minutes of keypad BLE LEDs will flash.
inactivity the keypad will emit Press this key to disable all fea-
GEMINI
6. The keypad will beep 3 times
tures within a LED type Program-
a steady tone indicating the
panel has been left in Dealer indicating the panel default val-
Program Mode. Enter Dealer
ming Block or to blank out digits in ues have been loaded.
Code to exit or press the 1 2 3 4 5 6 7 8 a Direct Entry type Programming 7. Remove wiring between terminal
key to return to Dealer Pro- Block. 15 (PGM) and terminal 3.
gram mode. TUS
ST A 8. Re-install original wiring for ter-
E D
ARM
minal 15 (PGM) and terminal 3.
Hexadecimal Data Entry Note: Any programming in
Dealer Options 1 [96] and Dealer
To Enter a hexadecimal digit enter the
following: Options 2 [97] will not be de-
Set Key faulted. If Dealer Code Lockout
Press this key before has been programmed the panel
A= D= will not default the Dealer Code.
entering a Program-
ming Block Number. &20387(5,=(' 6(&85,7< 6<67(0 B= E= The Event Log will be erased
when the panel is defaulted.
C= F=
Dealer Code ARMED ON Indicates the panel is in Dealer
Program Mode. The panel is
Entering Dealer Program Mode Enter + STATUS OFF
ready for a programming block to
TROUBLE FLASHING
be entered.
NOTE: (4) (5) (6) (7)
Entering Dealer Program Mode is not permitted while the panel
Default Dealer Code shown in parentheses
is Armed, Reporting, or the Bell Output is on. To Enter Dealer
Mode while the Bell is ON or the panel is Reporting or Armed;
power up the panel and enter Dealer Mode within the first 3
minutes. Pressing the key clears the 3 minute timer.
ARMED FLASHING Indicates the panel is Ready to
Dealer Code
exit Dealer Program Mode.
STATUS FLASHING
1
WI851A 8/97
LED Programming Block
Enable features by pressing the key that corresponds to the associated feature; the LED will turn ON. To disable a feature press the key
again; the LED will turn OFF. To disable all features within a LED Type Programming Block press the key; all LEDs will turn OFF.
OFF and 3 have been STA
TUS
²
ED
ARM
OFF
Direct Entry Programming Block
Enter data directly. For hexadecimal entries of A-F, use the key + through keys, respectively. Use
the key to blank out digits in Direct Entry type programming blocks. Default values are shown in parentheses.
Direct Entry
1 Direct Entry Programming Example 1 10 Exit Delay Type
Program the panel for a 60 second Exit Delay. Programming
0 6 0 Exit Delay, seconds Blocks
1. Press (Beep) (Beep). (0) (4) (5) Maximum Entry 255
2. Press ..
44 Dialing Prefix 9 E
(Hexadecimal data entry)
Program Telephone Prefix Number with a 9E.
ARMED OFF Indicates the panel is in Dealer Pro-
1. Press (Beep) (Beep). gram Mode; the next digit entered will
STATUS FLASHING
2. Press be interpreted as a Hexadecimal digit.
Valid entries are 1-6 (A-F).
3. Press TROUBLE FLASHING
4. Press
2
To view data within a programming Block enter the Program Block Number, the 1st digit will be displayed. Press the
pressing the
key to view the 2nd digit, continue
key until all digits within the Programming Block have been viewed. Data will be displayed in the binary format shown in the table below:
NOTE:
Value Data Displayed Value Data Displayed * In the following Programming
Blocks, data that has been entered
0/Blank 8 4 as a ‘0’ will be displayed as an ‘A’:
Subscriber ID Numbers, Phone
Numbers, Pager Leading and Trail-
For Technical Assistance,
1 1 9 1 4 ing digits and Report Codes.
Contact the NAPCO Toll
2 2 *A/0 2 4 Free Helpline
3 1 2 B 1 2 4 (800) 645-9440
4 3 C 3 4
5 D Zone # Bit Value
1 3 1 3 4 1 1 NOTE:
2 2
6 2 3 E 2 3 4 3 4 The Following Program-
4 8 ming Options are not
7 1 2 3 F 1 2 3 4 permitted for UL installa-
tions: [05], [06], [23-2],
Example: Viewing the Dialing Prefix [26-3] and [26-4].
44 Dialing Prefix 9 E
A Dialing Prefix of 9E has been programmed at Programming Block Num-
The UL symbol by a
ber 44 (outside access number). Follow the steps below to view the data.:
programming Block indi-
cates the programming
GEMINI option is not permitted
Press to enter Programming Block 44. The
1 for UL installations.
1 4
1st digit of Programming Block 44 is displayed.
TUS
STA
ED NOTE:
ARM DATA = 9
For information about
programming blocks re-
fer to GEM-P800 Instal-
2 Press the key to view the 2nd digit. GEMINI lation Manual WI850.
2 3 4
TUS
STA
ED
ARM DATA = E
3
01 Home/Away with Delay Zones 04 24 Hour Protection Zones 07 Burg (Steady) Output
Default Default Default
OFF Zone 1 OFF Zone 1 ON Zone 1
OFF Zone 2 OFF Zone 2 ON Zone 2
OFF Zone 3 OFF Zone 3 ON Zone 3
OFF Zone 4 OFF Zone 4 ON Zone 4
OFF Zone 5 OFF Zone 5 ON Zone 5
OFF Zone 6 OFF Zone 6 ON Zone 6
OFF Zone 7 OFF Zone 7 ON Zone 7
OFF Zone 8 OFF Zone 8 ON Zone 8
Default
Exit Delay, seconds Smoke Supervisory Timer, hours OFF Zn 1 LED ON = Audio Verification
(0) (4) (5) Maximum Entry 255 (8) Maximum Entry 8 UL OFF Zn 2 LED ON = *Access Output ( )
OFF Zn 3 LED ON = *Follow Keypad Sounder
11 Entry Delay 18 Test Timer Offset OFF Zn 4 LED ON = *Keyfob/Keyswitch Chirp
*See Note 2
Entry Delay, seconds Test Timer Offset, hours
24 Programmable Output (PGM) Features 2
(0) (3) (0) Maximum Entry 255 (1) (2) Maximum Entry 23 Default
OFF Zn 1 LED ON = Fire
12 Burg (Steady) Output Time-out OFF
6\VWHP )HDWXUHV Zn 2 LED ON = AUX
OFF Zn 3 LED ON = Panic
Bell Time-out, minutes
20 Keypad Features 1 OFF Zn 4 LED ON = Test Timer
(0) (0) (5)
Maximum Entry 255
Default
OFF 25 Programmable Output (PGM) Features 3
13 Fire (Pulsed) Output Time-out Zn 1 LED ON = *Keypad Fire ( )
Default
OFF Zn 2 LED ON = *Keypad AUX ( )
OFF Zn 1 LED ON = AC Fail
Bell Time-out, minutes ON Zn 3 LED ON = *Keypad Panic ( )
OFF Zn 2 LED ON = Low Battery
(0) (0) (0) Maximum Entry 255 OFF Zn 4 LED ON = *Ambush (8th User Code)
*See Note 1 OFF Zn 3 LED ON = *Trouble
21 Keypad Features 2 OFF Zn 4 LED ON = Armed
14 Test Timer Interval
*See Note 3
Default
Test Timer, days ON Zn 1 LED ON = Audible panic 26 Miscellaneous Features 2
Default
(0) (0) (1) Maximum Entry 255 OFF Zn 2 LED ON = Exit/Entry with Urgency
OFF Zn 1 LED ON = Momentary Keyswitch Arming
ON Zn 3 LED ON = Display Bypass (ARMED)
OFF Zn 2 LED ON = Reserved
15 Line Cut Time-to-Fail (Disabled = 000) OFF Zn 4 LED ON = Disable Code Entry Beeps
UL OFF Zn 3 LED ON = Inhibit Fail to Communicate
Line Cut Time-to-Fail, seconds 22 Miscellaneous Features 1 UL OFF Zn 4 LED ON = Inhibit Low Battery Display
(0) (0) (0) Enable Feature-Valid Entries 10-255 Default
OFF Zn 1 LED ON = Abort Delay NOTE 2:
Cannot be programmed with any other Programmable Output (PGM) Feature.
ON Zn 2 LED ON = Easy Arm/Easy Exit
16 Wireless Supervisory Timer
ON Zn 3 LED ON = Swinger Shutdown
NOTE 3:
Supervisory Timer, hours OFF Zn 4 LED ON = Bell on Line Cut (Armed) Includes Bell Cut, Fire Trouble, Receiver Fail-to-Respond, Receiver Tamper,
Receiver JAM, Transmitter Low Battery, Transmitter Supervisory Faliure,
(1) (2) Maximum Entry 26 NOTE 1: Wireless Smoke Low Battery and Wireless Smoke Supervisory Failure.
Additional programming required for reporting, see Blocks [36]&[56].
UL Installations: If Keypad Fire [20-1] is enabled, the keypad must be mounted
within (3) three feet from the Control Panel. 5
OFF Zn 7 LED ON = User 7 Reporting
36 System Reporting, Telco 1
OFF Zn 8 LED ON = User 8 Reporting
33 Receiver Options Default
Default
OFF Zn 1 LED ON = *KP Fire ( )
NOTE 1:
ON Zn 1 LED ON = 2300 Hz Handshake/Kissoff OFF Zn 2 LED ON = *KP AUX ( )/Ambush
Requires features to be enabled, see block [20].
OFF Zn 2 LED ON = Sumcheck ON Zn 3 LED ON = *KP Panic ( )
45 Communicator Features 1
Default
NOTE: ON Zn 1 LED ON = Communicator Enabled
A fixed Dial Tone Detection (E) is included prior to the Dialing Prefix (Block
Number 44). Programming an E is not required for Telco 1, Telco 2 and
ON Zn 2 LED ON = DTMF w/ Rotary Back up
Telco 3. If dial tone detection is not desired select No Dial Tone Detection in OFF Zn 3 LED ON = DTMF only
Communicator Features (Block Number 46). Program a D if a 4 second
delay is required. OFF Zn 4 LED ON = Backup to Telco 2
48 Trailing Digits
42 Receiver Format
46 Communicator Features 2
*(C) *See Note 1
[1] Ademco Slow Default
[2] Radionics Slow (4) OFF Zn 1 LED ON = No Dial Tone Detection
[3] Silent Knight Fast OFF Zn 2 LED ON = 2:1 Rotary Dialing
[4] Universal High Speed OFF Zn 3 LED ON = Backup if < 4 attempts 49 Pager Option
[5] Reserved OFF Zn 4 LED ON = Reserved Default
[6] Point ID OFF Zn 1 LED ON = Skip Alarm Data
[7] Pager
OFF Zn 2 LED ON = Reserved
OFF Zn 3 LED ON = Reserved
OFF Zn 4 LED ON = Reserved
43 Receiver Options
Default
ON Zn 1 LED ON = 2300 Hz Handshake/Kissoff
OFF Zn 2 LED ON = Sumcheck
OFF Zn 3 LED ON = Single Digit
OFF Zn 4 LED ON = No Handshake NOTE 1:
C = TouchTone #. This is the typical terminating digit for
most paging systems. Recommended, but may not be
required by paging system. D = 2 second delay.
OFF Zn 7 LED ON = User 7 Reporting
56 System Reporting, Telco 3
OFF Zn 8 LED ON = User 8 Reporting
53 Receiver Options Default
OFF Zn 1 LED ON = *KP Fire ( )
Default
NOTE 1:
ON Zn 1 LED ON = 2300 Hz Handshake/Kissoff OFF Zn 2 LED ON = *KP AUX ( )/Ambush
Requires features to be enabled, see block [20].
OFF Zn 2 LED ON = Sumcheck OFF Zn 3 LED ON = *KP Panic ( )
(3) 63 System Report Codes
Zone 4 Alarm Code 66 Ambush Report Code
(3) Keypad Fire ( )
Zone 5 Alarm Code (1) (1)
(3) (2) (2)
Keypad AUX ( )
Zone 6 Alarm Code
(2) (3)
(3)
Keypad Panic ( )
Zone 7 Alarm Code
(2) (1)
(3) Enhanced Communicator Features
Test Timer
Zone 8 Alarm Code
(F) (F)
(3) 67 Telephone Number 1
AC Fail
Default
(F) (9)
61 Point ID Report Codes OFF Zn 1 LED ON = Opening after Alarm (Cancel Code)
Low Battery
(F) (8) OFF Zn 2 LED ON = Conditional Closing
Zone 1 Alarm Code
*Trouble OFF Zn 3 LED ON = Reserved
(3) 1 FIRE
Zone 2 Alarm Code 2 PANIC (F) (1) OFF Zn 4 LED ON = Reserved
3 BURGLARY Fire
(3)
4 HOLDUP
Zone 3 Alarm Code 5 GENERAL ALARM
(1) (1)
68 Telephone Number 3
(3) 6 RESERVED *See Note 1
Default
Zone 4 Alarm Code 7 GAS ALARM
8 HEAT ALARM 64 System Restore Code OFF Zn 1 LED ON = Opening after Alarm (Cancel Code)
(3) 9 RESERVED OFF Zn 2 LED ON = Conditional Closing
Zone 5 Alarm Code A AUXILIARY
B 24 HOUR ALARM OFF Zn 3 LED ON = Reserved
(3) (E)
Zone 6 Alarm Code OFF Zn 4 LED ON = Reserved
(3)
Zone 7 Alarm Code
NOTE 1:
(3) Includes Bell Cut, Fire Trouble, Receiver Fail-to-Respond, Receiver Tamper,
Zone 8 Alarm Code Receiver JAM, Transmitter Low Battery, Transmitter Supervisory Faliure, Wire-
less Smoke Low Battery and Wireless Smoke Supervisory Failure.
(3)
9
73 Zone 3 :
RF ID # XXXXXX:X 1. Enter Dealer Mode.
2. Enter (beeps) (beeps)
74 Zone 4 :
3. Enter
75 Zone 5 : 4. Enter (beeps)
Enter the point number to be
associated with the zone. If only
76 Zone 6 : one point of GEM-TRANS2 is
Hexadecimal B Entry
10
A=
B= C= D= E= F=
OFF Zn 1 LED ON = Dealer Code Lockout
OFF Zn 2 LED ON = Answering Machine override (9)
ON Zn 2 LED ON = User 1 Code Lockout
OFF Zn 3 LED ON = Function 6 ( ) Download
OFF Zn 3 LED ON = UL Household Fire
OFF Zn 4 LED ON = Signal Strength Test Mode
OFF Zn 4 LED ON = Fire Trouble on Fire LED
NOTE 1:
International Features
93 Auto Download ID Number
11
RED
GRN
GRAY
BRN
SEE WI850).
Programmable
EZ + +
P$ 0$;
Class 2
5('
*51
%/.
Transformer.
Output
/2
Zone RED GOLD
A'
TM
Doubling RED RED connect to
To RJ31X
switched +
EARTH
.
Resistors
.
.
outlet. (Supervised)
GROUND (Z) (Z) (Z) GEM-RP8
3.9K + WARNING
(Z) +
TO PREVENT RISK
(1) ZONE 4 ZONE 5 ZONE 6
OF ELECTRIC SHOCK
25$1*( *2/'
:+,7( 5(' DISCONNECT TELEPHONE
.
.
.
ZONE 1
12