Professional Documents
Culture Documents
STANDARD
Third edition
1990-07-l 5
Reference number
IS0 565: 1990(E)
COPYRIGHT 2002; International Organization for Standardization Document provided by IHS Licensee=Fluor Corporation/2110503105, User=,
10/30/2002 03:32:11 MST Questions or comments about this message: please call
the Document Policy Management Group at 1-800-451-1584.
IS0 565:1990(E)
Foreword
IS0 (the International Organization for Standardization) is a worldwide
federation of national standards bodies (IS0 member bodies). The work
of preparing International Standards is normally carried out through IS0
technical committees. Each member body interested in a subject for
which a technical committee has been established has the right to be
represented on that committee. International organizations, govern-
mental and non-governmental, in liaison with ISO, also take part in the
work. IS0 collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an Interna-
tional Standard requires approval by at least 75 % of the member bodies
casting a vote.
International Standard IS0 565 was prepared by Technical Committee
ISO/TC 24, Sieves, sieving and other sizing methods.
This third edition cancels and replaces the second edition
(IS0 565:1983), of which it constitutes a technical revision (see the In-
troduction).
Annex A of this International Standard is for information only.
--
||
||| | || |
||||
|||| || ||||||| || | |
| | ||---
6 IS0 1990
All rights reserved. No part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without
permission in writing from the publisher.
International Organization for Standardization
Case Postale 56 l CH-1211 Genbve 20 l Switzerland
Printed In Switzerland
ii
COPYRIGHT 2002; International Organization for Standardization Document provided by IHS Licensee=Fluor Corporation/2110503105, User=,
10/30/2002 03:32:11 MST Questions or comments about this message: please call
the Document Policy Management Group at 1-800-451-1584.
IS0 565:1990(E)
--
Introduction
||
||| | || |
ond edition of IS0 565 which was published in 1983, the range of sizes
of openings were extended down to 5 pm by introducing the values of
|||| || ||||||| || | |
the R’IO series, in accordance with IS0 497, for all principal sizes from
32 pm and smaller.
In the meantime it has been recognized that there is little call for some
| | ||---
Table 0.1
f
Series IS0 3
Step Ratio
and IS0 497
...
III
COPYRIGHT 2002; International Organization for Standardization Document provided by IHS Licensee=Fluor Corporation/2110503105, User=,
10/30/2002 03:32:11 MST Questions or comments about this message: please call
the Document Policy Management Group at 1-800-451-1584.
--
||
||| | || |
COPYRIGHT 2002; International Organization for Standardization Document provided by IHS Licensee=Fluor Corporation/2110503105, User=,
10/30/2002 03:32:11 MST Questions or comments about this message: please call
the Document Policy Management Group at 1-800-451-1584.
INTERNATIONAL STANDARD IS0 565:1990(E)
1 Scope 4 Designation
2 Normative reference
COPYRIGHT 2002; International Organization for Standardization Document provided by IHS Licensee=Fluor Corporation/2110503105, User=,
10/30/2002 03:32:11 MST Questions or comments about this message: please call
the Document Policy Management Group at 1-800-451-1584.
IS0 565:1990(E)
| | ||---
Principal sizes Supplementary sizes Principal sizes Supplementary sizes
|||| || ||||||| || | |
R 20/3 R 20 R 4Oi3 R 2Oi3 R 20 R 4Oi3
||||
100 710 710 710
90 90 90 630
||| | || |
80 600
75 560
||
71 500 500 500
--
63 63 63 450
56 425
53 400
50 355 355 355
45 45 45 315
40 300
37,5 280
35,5 250 250 250
31,5 31,5 31,5 224
28 212
26,5 200
25 180 180 180
22,4 22,4 22,4 160
20 150
19 140
18 125 125 125
16 16 16 112
14 106
13,2 100
12,5 90 90 90
11,2 11,2 11,2 80
10 75
995 71
9 63 63 63
8 8 8 56
791 53
67 50
63 45 45 45
596 5,6 596 40
5 38
4,75
36
495
4 4 4 R'lO
3,55
3,35 32
3,15 25
2,8 23 24 20
295 16
2,36 10
2,24 5
2 2 2
13
197
196
194 14 1,4
1,25
1,18
1,12
1 1 1
COPYRIGHT 2002; International Organization for Standardization Document provided by IHS Licensee=Fluor Corporation/2110503105, User=,
10/30/2002 03:32:11 MST Questions or comments about this message: please call
the Document Policy Management Group at 1-800-451-1584.
IS0 565:1990(E)
Annex A
(informative)
Bibliography
[I] IS0 3:1973, Preferred numbers - Series of [4] IS0 3310-2:-1) , Test sieves - Technical re-
preferred numbers. guirements and testing - Part 2: Test sieves
of perforated metal plate.
[2] IS0 497:1973, Guide to the choice of series of
preferred numbers and of series containing [5] IS0 3310-3:1990, Test sieves - Technical re-
more rounded values of preferred numbers. guirements and testing - Part 3: Test sieves
of electroformed sheets.
[S] IS0 3310.1:1990, Test sieves - Technical re-
--
COPYRIGHT 2002; International Organization for Standardization Document provided by IHS Licensee=Fluor Corporation/2110503105, User=,
10/30/2002 03:32:11 MST Questions or comments about this message: please call
the Document Policy Management Group at 1-800-451-1584.
IS0 565:1990(E)
| | ||---
|||| || ||||||| || | |
||||
||| | || |
||
--
UDC 621.928.028
Descriptors: test equipment, sieves, wire cloth, sieve plates, openings, dimensions, hole size.
COPYRIGHT 2002; International Organization for Standardization Document provided by IHS Licensee=Fluor Corporation/2110503105, User=,
10/30/2002 03:32:11 MST Questions or comments about this message: please call
the Document Policy Management Group at 1-800-451-1584.