User's Guide
M3 Wireless Digital Transmission System
Thank you for choosing the M3 wireless transmission system. Please read the
following instructions carefully before you use it.
ES
1. This product contains a wireless transmitter and a wireless receiver, Both of them
must be used together.
2. Services required when the apparatus has been damaged in any way, such as:
“Liquid has been spilled or abjects have fallen into the apparatus.
“The unit does not operate normally or changes in performance in a significant way.
“The unit is dropped or the enclosure is damaged.
3. Do not place near heat sources, such as radiators, heat registers, or appliances
which produce heat
4. Guard against objects or liquids entering the device. Do not use or place unit near
water.
5. Clean only with a damp cloth.
6. Only use attachments or accessories specified by the manufacturer.
7. Prolonged listening at high volume levels may cause irreparable hearing loss and
or damage. Always be sure to practice safe
<1ms(Almost no delay)
250 meters(160 teet)*
20-20K Hz,+1dB/-30B
10°C to SO°C
* Note: Actual range is dependent on RF environment,including reflections,
interference and absorption.SV USB
M3 RECEIVER FIGURE
D Power bution QAudio signal indicator LED “Channel select button G)Power Indicator LEDRECEIVER TRANSMITTER
Power On/Off:
1, Press the power button () of the transmitter for 1 second, the ID indicator @) lights up,
and the transmitter starts. Under the working state, press the same bution for 1 second to
shut down the machine, { Usually, turn on the transmitter power first.)
2. Press the power button () of the receiver for 1 second, the ID indicator LED @ lights up,
the receiver is tumed on and connected in pairs automatically, and press the button for 1
second to tum off the receiver when it is working state, ( Note. If the receiver is tured on
first, ID indicator @) wall flicker slowly, and then when the transmitter is turned on, |
indicator (2) will become constant and no longer flicker,)3. Transmitter plugs into the Guitar (your instruments), the Receiver plugs into the
effects pedal, AMP, Audio, etc.
4. Now, let's rock logether.
‘When the transmitter and receiver power are tumed on and the receiver ID indicator (2) is
flickering slowty, then it needs to be rematched. The operation is as follows:
Firstly, in the boot state of the transmitter, press the PAIR. button @) , the ID indicator @
‘will flicker. Then pay attention to whether the ID indicator @) is still flickering slowly when
the receiver is on. If it is still flickering, it is necessary to press the PAIR. button 3 of the
transmitter again. It will be up in 1-4 times. The ID indicator LED @ of the receiver and
Iransmitter is always on and no longer flickers when the code is successful, that is, the two
units rematch successful and will work reguiarty.
(Generally, whan two or more sets are used under the same scene al the same time, we need
to select different frequency channels. Press PAIR. button G , count the number of flickers of
ID indicator lights, If flicker oné time, It means the system works on channel 1, if flicker two
times, it means the system works on channel! 2, if flicker three times, it means the system
works on channel 3, if flicker four times, it means the system works on channel 4. The M3 has
‘8 total of four channels. That is, four systems can be used at the same time. (Each pair of
fransmitters and receivers must be tuned to the same channel at the same time, (hat is, the
code is matched successful before they can be used. Usually they are paired before they
leave the factory.)
~By the pach cord.you cen send the sional oblans
by receiver to the compuler, table PC or cellphone.
-You an quip right pateh cord seooingtoyorom|
equipment type.
-By this way, you can record the voice made from
instrument or sh on the internet,
Three-channel 3.Srim plug
connects mobile phone cr
Ce as a aero Sree
ns okard
1. The indicator CHARGE @) will flicker until there is no electricity. The CHARGE @ LED
lights up when the USB interface is charged, and the indicator lights out when it is full of
electricity
2. When press the POWER button as usual, the ID indicator (2) does not bight. There may
be insufficient power, please try lo charge.