Professional Documents
Culture Documents
Application User Manual
Application User Manual
LG Innotek
Hanyang Univ. 1271, Sa-dong, Sangrok-gu ,
Ansan-si, Gyeonggi-do 426-791, Korea
Tel:82-31-436-7653
Fax:82-31-436-7991
www.lginnotek.com
RECORD OF CHANGES
RBFS-B921A-AN-05-A Page 1
RBFS-B921A
1. HARDWARE OVERVIEW
This is User manual for RBFS-B921A which is a Class 2 (4dBm Max.) Bluetooth® Module for
Consumer Applications(such as TV).
Each unit consists of a DV kit and a Bluetooth Ass’y Module. The Module shipped with the system
uses the Broadcom BCM2046™ chip and also includes the filter, EEPROM, a crystal and an internal
antenna. The radio module plugs into the carrier board. Hardware upgrades will be shipped in the
format of a new replacement radio module when new versions of the LGIT Module product range
become available. The DV kit provides a serial port (RS232), SPI port, USB port, power supply
socket and audio socket.
RBFS-B921A
HCI Class2 Ass’y Module Audio
socket
TP point
TX/RX
LED
Reset
switch Power
Carrier board LED
USB Power
socket
RBFS-B921A-AN-05-A Page 2
RBFS-B921A
( Unit : mm )
RBFS-B921A-AN-05-A Page 3
RBFS-B921A
2 GND I Ground
4 GND I Ground
6 GND I Ground
8 GND I Ground
10 GND I Ground
TOP View
1 2 3 4 5 6 7 8 9 10
Indicate Mark
RBFS-B921A-AN-05-A Page 4
RBFS-B921A
EEPROM
Antenna
(128k)
VDD
USB
Host
Band Pass BT Chip(HCI) Connector GND
Filter BCM2046 (10pin)
RESET
VREG_CTR
Clock
(26MHz)
RBFS-B921A
Daughter Board Module
RBFS-B921A-AN-05-A Page 5
RBFS-B921A
The LBTS-XX97A Bluetooth Development kit(DV-kit) has been developed primarily to assist LGIT
customers in the development of the host side software and external radio circuits. It will also be
used to assist LGIT customers to evaluate the LGIT Module. The evaluation system consist of two
identical module that allow the user to send both data and voice over bluetooth link. Each unit is
driven from PC for data connection and from a headset for voice connection.
The DV-kit provides serial port(UART/RS232), USB port, SPI port, Audio socket(3.5’), power
supply socket. The signal level on the RS232 port conform to the RS232 standard and are generated
on the DV-kit board.
Audio
socket
TP point
TX/RX
LED
Reset
switch Power
LED
USB Power
socket
RBFS-B921A-AN-05-A Page 6
RBFS-B921A
POWER SUPPLY
Power is supplied by USB cable. Supplied voltage power is regulated as 3.3V, and this regulated
power is used as supply voltage on the DV-kit board.
Regulator accepts voltage within the range of 4.8VDC~15VDC, and supplies 1A.
In case that, user’s application circuits are added to the development kit, total usable power of
additional circuit should not exceed 1A of LDO
RESETB
The LGIT DV-kit allow the users to make RESET signal directly. Reset switch is
Reset by S/W is also available through SPI interface.
USB and UART(RS232) interface enable communication with Bluetooth HCI controller.
LGIT Bluetooth Development kit automatically select one HCI interface whether UART(RS232) or
USB connected.
UART/RS232
RBFS-B921A-AN-05-A Page 7
RBFS-B921A
USB
LGIT’s USB Bluetooth DV-kit support HCI controller of Bluetooth module and USB interface.
Also, this DV-kit fulfills the USB 1.1 specification requirement, functions as regular USB slave port.
Specially designed USB cable enables to connect the devices by using USB(‘B type) connector.
For the first time user, this kit support ‘plug and play’, installation wizard.
Refer to clause 5.
PCM/AUDIO
RBFS-B921A-AN-05-A Page 8
RBFS-B921A
3. HARDWARE SETUP
Remove the Power supplies and the appropriate mains power connector from the carry carry case
and push the mains connector onto the power supplies, making sure that they are fully pressed home.
Plug these two power supplies into the mains but DO NOT connect the DC output connector to the
LGIT Evaluation system units yet. The power supplies should be connected AFTER the
Bluetooth utility software is installed and configured.
UART/RS232
Remove the USB cable from the carry case and connect one end of USB ports on PC’s
(WindowTM2000/XP).
• The power supplies should be connected AFTER the Bluetooth application S/W (utility) is
installed and configured.
• Using Bluetest or BlueChat utility program
USB
Remove the USB cable from the carry case and connect one end of USB ports on PC’s
(WindowTM2000/XP).
• The power supplies should be connected AFTER the Bluetooth application S/W (utility) is
installed and configured.
• Using BlueTool program
RBFS-B921A-AN-05-A Page 9
RBFS-B921A
Installation instructions
1) Download attached file ‘Active Perl’ and ‘Bluetooth_M1’
2) Change the path if required, click ‘unzip’, click ‘OK’ and finally click ‘Close’ to complete
the installation
3) From your PC in the folder run the file ‘Active Perl.exe’
RBFS-B921A-AN-05-A Page 10
RBFS-B921A
C:\WINDOWS\system32
"btw_ci.dll" copy to upper directory
RBFS-B921A-AN-05-A Page 11
RBFS-B921A
• Install USB to UART convert IC Driver – also available download from FTDI of website.
www.ftdichip.com/Documents/InstallGuides.htm
Installation instructions
1) Download attached file ‘DV KIT USB DRIVER.zip’
2) Change the path if required, click ‘unzip’, click ‘OK’ and finally click ‘Close’ to complete
the installation
3) From your PC in the folder installing as below
DV KIT USB Driver\Old version and New version folder.
4) Refer to installation guide book ‘Windows_XP_Installation_Guide - Part III’
RBFS-B921A-AN-05-A Page 12
RBFS-B921A
Start the Bluetool Program on each PC by double Clicking on the Bluetool shortcut on your desktop.
RBFS-B921A-AN-05-A Page 13
RBFS-B921A
Start the Bluetool Program on each PC by double Clicking on the Bluetool shortcut on your desktop.
RBFS-B921A-AN-05-A Page 14
RBFS-B921A
RBFS-B921A-AN-05-A Page 15
RBFS-B921A
RBFS-B921A-AN-05-A Page 16
RBFS-B921A
RBFS-B921A-AN-05-A Page 17