Professional Documents
Culture Documents
Sequential Discovery Puzzle Box
Sequential Discovery Puzzle Box
by Durss
In this simple puzzle box you have to open a tiny drawer by deciphering hints engraved on its top.
Some tools included need to be used to unlock other tools and solve enigmas which makes it a "Sequential Discovery"
kind of puzzle
Supplies:
Taping the wood sheet will avoid leaving burn marks on the wood.
Laser cutters usually make burning marks due to the heat and ventilation next to the laser head which doesn't looks
good.
Adding tape makes it so the burning marks are only left on the tape, leaving the wood under it much cleaner.
The image above shows the params i'm using and estimated cutting time on my Glowforge basic.
Download
https://www.instructables.com/ORIG/FC8/26RP/KZE4XIMV/FC826RPKZE4XIMV.svg
Remove the masking tape from all the cut wood parts
Many parts will have to slide between the top and bottom parts of the puzzle.
For them to be able to slide you will have to sand them so they are at least 0.2mm thinner.
Use the 80grit sand paper to scratch as much of the parts then soften it with higher grit if you have any.
Measure with a caliper, if you have one, the thickness before sanding and make sure the part is as evenly
thinner as possible.
The parts that need to be thinner are all the ones on the picture above.
Be careful not to sand the sides that have lines on them, these are important hints to solve the box !
Sanding the parts made sure that they won't be clamped between the top and bottom parts but it probably won't be
enough to make them slide smoothly. There will still be lots of friction.
There are some parts that must slide really well or the puzzle reset won't work properly.
The rst one is the top right part in red on the picture above.
To make sure it slides properly and the mechanism won't stay locked, push it down against the little rod (in blue).
Apply a constant pressure downward on the red part and pull down the green part.
The red part should be free to go down on place of the blue part.
If not then try to very slightly shorten the blue rod.
https://www.instructables.com/ORIG/FFJ/E38M/KZE4XQJM/FFJE38MKZE4XQJM.mp4
Now we need to do the same test for the top left part.
This time put the red part down, make sure the blue part goes inside its groove, and apply constant pressure upward on
red part while pulling down the green part.
The red part should be able to go up.
https://www.instructables.com/ORIG/FAG/FC1O/KZE4XRS1/FAGFC1OKZE4XRS1.mp4
Before glueing the top of the box we need to make sure things slide properly one last time.
1. Push the key holder on the left very gently, it should automatically close at some point
2. The top right part should be pushed down
3. The top left part should be pushed up
4. When everything in "open" state (top right parts on the top, top left part the bottom) , pulling down the
middle part should release the top left/right parts.
If any of these do not work, you might have to sand the sides of the moving parts to reduce the friction against the xed
parts.
The chicago screw of the top part has some thickness that would induce a gap if we tried to glue the top part.
To avoid that we need to dig the red part of the picture for ~1,5mm.
You should have a laser cut line indicating the area to dig.
If you have a wood carving knife it's the best, but you can also do it with a cutter as well. Just be careful with your ngers !
The two cursors named "1" must be inserted on the parts as shown in the second image.
The cursors named "2" must be set inside the grooves on the right of the board and in the proper orientation.
They all have a short lead and a long lead and must be placed as shown on the 3rd and 4th images
Tip : Don't try to close the drawer, magnets will drive crazy, just leave it opened and close it once glue is dry
I won't explain the riddles to solve but the video above shows the steps to reproduce to open the box.
You will want to do that a rst time to close the drawer left open on the previous step.
Once all the steps are done you'll be able to close the drawer and pull down the last cursor to keep it in place.
Just reproduce the other steps backward and the box will be reset.
https://youtu.be/pyS_bSRUrN8
Looks Great!
great project.
did you design everything by yourself?
Absolutely :)
:D
Amazing! :D