ae
Page 11
EN 1652 : 1997
8.7 Rounding of results
For the purpose of determining conformity to the limits specified in this standard, an observed or a calculated —
value obtained from a test shall be rounded in accordance with the following procedure, which is based upon the _
guidance given in annex B of ISO 31-0 : 1992. It shall be rounded in one step to the same number of figures
used to express the specified limit in this standard, except that for tensile strength the rounding interval shall be
10 N/mm? and for elongation the value shall be rounded to the nearest 1 %.
The following rules shall be used for rounding:
a) if the figure immediately after the last figure to be retained is less than 5, the last figure to be retained
shall be kept unchanged; .
b) if the figure immediately after the last figure to be retained is equal to or greater than 5, the last figure to
be retained shall be increased by one.
| 9 Declaration of conformity and inspection documentation
9.1 Declarat
In of conformity
When requested by the purchaser Isee 5 n)] and agreed with the supplier, the sepplier shall issue for the products
the appropriate declaration of conformity in accordance with EN 1655
9.2 Inspection documentation
When requested by the purchaser [see 5 o)] and agreed with the supplier, the supplier shall issue for the products
the appropriate inspection document in accordance with EN 10203.
10 Marking, packaging, labelling
Unless otherwise specified by the purchaser and agreed by the supplier, the marking, packaging and labeling
shall be left to the discretion of the supplier (see 5 pl
Table 1: Composition of copper
Composition in % {mim} Density’
Material designation Other elements] g/cm?
Element} Cu") Bi co ° Pb (see note)
Symbol_| Number total_Jexcluding| sor
99,
pure cea max. - 10,000 §]0,040%) = 0,005 | 0,03 [Aso ue
min. | 8850] = = = =
cu-rnte | cwooea | mn | 99: Sule = | gos ano] 8.9
min. | 99,55 J —— = = = =
egOF cNoeen max. - 10,000 5} -*) - 0,005 | 0,03 Ao cg
mn, | S850 = =] o005 |= =
Pape owas max. « 10,000 5 - 0,013 | 0,005 | 0,03 Ben Nel 6:8
min, | 95.50 | a =
cubHe | cwozea | mn | 99: ~ Mics - : 8,9
=
') Including Ag, up to a maximum of 0,015 %.
2) For information only. :
+) Oxygen content up to 0,060 % is permitted, subject to agreement between the purchaser and the
supplier
*) The oxygen content shall be such that the material conforms to the hydrogen embrittlement
requirements of prEN 1976.
NOTE: The total Of other elements (than copper) is defined as the sum of Ag, As, Bi, Cd, Co, Cr, Fe, Mn,
Ni, 0, P, Pb, S. Sb, Se, Si, Sn, Te and Zn, subject to the exclusion of any individual elements indicated.Table 3: Mechanical properti
Designations Nominal thickness [Tensile strength] 0,25 Elongation Hardness Grain size
Proof strength
Ry Roo2 Asonn A HV
for thicknesses|for thicknesses,
upto and | over 2,5 mm
including
2,5 mm
Material Material mm Nien? Nim? % % mm
condition
‘up to and
Symbol_| Number from _| including | min | max rn. on. rin [max | min | mae
R200 aa 200 [250 | Imax. 100) = a = = = =
HOG ow = = = = = a, 8] =
[R22 ae ; OT 260-[_ max Ta0T a = e = =
Oa " = = BE = = aO_[ es =
icu-eTP Wo04A
currTe “eWooea a TEOT = —
Kuor — fewoosa | FEZ 0.2 18 Soe eof eee T HO] Li z ae
uDLP |cwo23a = S = = = 5
u-DHP — |ewo2aa
R290 a 1S 230] 360] train 2501 = é = s = E
OSS : = = = = = Eo
[R360 360 Train, 3207 z = 5 = =
HiTo aa L = = = = = 110 | = =
(continued)