Professional Documents
Culture Documents
Far28x7 SM
Far28x7 SM
FAR-2107/2807 series
FAR-2117/2127
FAR-2817/2827
FAR-2827W
FAR-2137S/2837S
FAR-2837SW
Important;
This manual is intended for use by authorized
FURUNO service technicians for the installation
of this equipment.
Under no circumstances should the contents of
this manual be released to the user.
The paper used in this manual
is elemental chlorine free.
9-52 Ashihara-cho,
Nishinomiya 662-8580, JAPAN
Telephone : 0798-65-2111
Fax : 0798-65-4200
*SME35190A00*
*SME35190A00*
*SME35190A00*
Contents
Introduction ..................................................................................... 1
1. Calling up an operational menu...................................................................................1
2. Do not turn off the power immediately after changing the setting ..............................1
3. Changing of IP address ................................................................................................1
4. Display of HDG, SPD and POSN................................................................................1
5. Notes for setting .........................................................................................................1
6. Checking on NMEA data interface..............................................................................2
7. Loop Back test .............................................................................................................2
8. ERROR/ALM..............................................................................................................2
9. Program updating ........................................................................................................2
10. Connection of sub monitor ........................................................................................2
11. LAN connection.........................................................................................................3
12. Connection with ECDIS ............................................................................................4
13. Compatibility of RPU-013.........................................................................................4
1
Contents
2
Contents
3
Contents
4
Contents
5
Contents
6
Contents
7
Contents
8
Contents
25. When the power is restarted immediately after turning the power off,
the ST-BY status starts within 3 minutes. ...............................................................8-6
26. What is the difference among the IMO, A, B, C and W types?
See page. 4-25. ........................................................................................................8-7
27. When the [1:HL OFF] key is pressed, the range ring and all marks disappear.
Is this normal? .........................................................................................................8-7
28. Where is the power switch of MU-201CR and MU-231CR located?
See page.7-74. .........................................................................................................8-7
29. The power cannot be turned on.
See page.6-25. .........................................................................................................8-7
30. NAV data is not inputted.
See page.4-27, 4-50, 6-9 to 6-16. ............................................................................8-7
31. Is there a priority order for NAV-data connecting ports on the TB board?
See page.6-11. .........................................................................................................8-8
32. The position and speed data displayed in red.
See page.3-4 and 6-12. ...........................................................................................8-8
33. Show the list of error message.
See page.6-31. .........................................................................................................8-8
34. Show the manual method for CABLE ATT ADJ.
See page.4-13. .........................................................................................................8-8
35. The sensitivity (gain) has become lower.
See page.3-15, 4-28, 6-42 and 7-51. .......................................................................8-8
36. ARPA targets are quickly lost.
See page.4-8. ...........................................................................................................8-9
37. The antenna does not rotate on FAR-2837SW.
See page.4-24. .........................................................................................................8-9
38. The antenna rotation speed cannot be switched although RSB-097 is installed.
See page.4-68. .........................................................................................................8-9
39. Screen is blank even if the RCU-015 is turned on. ...................................................8-9
40. The [BRILL] box menu is not displayed. And the brilliance cannot be adjusted
even by turning the BRILL control.
See page. 4-41 and 7-73. ........................................................................................8-10
41. The monitor size and picture size does not match each other.
See page. 4-41 and 7-73. ........................................................................................8-10
42. NMEA data is shared in the LAN connection.
See page. 4-51. ........................................................................................................8-10
43. The number of mark points .....................................................................................8-10
44. Can marks and lines created on GD-280 and GD-680 be used? .............................8-10
45. What can be saved on a memory card CU-200?
See page.6-45 to 6-47. ............................................................................................8-10
46. How to erase the MARK. ........................................................................................8-11
47. How to display echoes in color
See page.3-17 and 4-25. .........................................................................................8-11
48. How to create the NAV line
See Chapter 5 of the Operator’s Manual. ...............................................................8-11
49. The NAV LINE from GPS cannot be displayed. .....................................................8-11
9
Contents
50. Is it possible to make the setting of AIS static information and to send AIS
messages from the FAR?
See page.3-13. .........................................................................................................8-12
51. What are the conditions for the loss of AIS targets? ...............................................8-12
52. Show the symbol marks of the AIS and ARPA.
See the Operator’s Manual of the FAR. ..................................................................8-13
53. How should the setting be made on radar side when the ECDIS is connected?
See page.4-83. .........................................................................................................8-13
54. How to display the BARGE MARK
See page.4-38. .........................................................................................................8-13
55. How to connect the EG-3000
See page.6-49. .........................................................................................................8-14
56. How to set “Video Channel” on the VDR side
See page.4-55 and 4-57. .........................................................................................8-14
57. How to update a program
See Chapter 5. .......................................................................................................8-14
58. What boards can be used commonly for X-band and S-band?
See page.5-2 and 6-37 to 6-39. ...............................................................................8-14
59. What are components needing periodic replacement?
See page.6-42, 6-48 and 2-14. ................................................................................8-14
60. How to determine the power cable size. ..................................................................8-15
61. How to measure the frequency of the X-band radar ................................................8-15
62. Can SC-60/120/50/110 be connected with the IMO-type radar for heading data? ..8-15
63. The trackball of the control unit does not move smoothly. .....................................8-16
64. Proper menu setting is not known. How can the setting be reset to the default?
See page.4-1. ...........................................................................................................8-16
65. Although noise appears on the screen, echoes are not displayed.
See page.6-7. ...........................................................................................................8-16
66. Radar echo alignment is abnormal in azimuth direction.
See page.4-24. .........................................................................................................8-17
67. A message related to a communication error between Processor and TR or
Control unit is displayed in the ALERT box. How can the lines between the units
be checked?
See page.6-2 and 6-31 to 6-36. ...............................................................................8-17
68. The ALERT BOX displays VIDEO error.
See page.4-77 and 6-32. .........................................................................................8-18
69. Give the information on SYSTEM FAIL alarm.
See page.4-58. .........................................................................................................8-18
70. Echoes are reversed left to right on the S-band radar. .............................................8-19
71. How to adjust the Magnetron after being replaced.
See page.6-43. .........................................................................................................8-19
72. Give basic information on radars. ............................................................................8-20
1) Comparison between S-band and X-band ..................................................8-20
2) Range resolution: ........................................................................................8-20
3) Minimum range: .........................................................................................8-20
4) Bearing resolution ......................................................................................8-21
5) Propagation distance (Radar horizon) ........................................................8-21
10
Contents
11
Contents
12
Introduction
Introduction
This section describes minimum information required for settings and on equipment.
Note:
After making the “INSTALLATION” settings in the [INITIALIZE] menu,
restart the power.
1
Introduction
2
Introduction
Note: To make the LAN cable, see the Operator’s Manual of HUB-100 for details.
1. Cut neatly except for the leaving 11 mm. Then, fold the shield and the drain wire of
the cable. Moreover, insert into the plug housing
2. Insert until you can find the edge of cable from the housing.
3. Use the crimping tool to finish.
11 mm
Crimp the drain wire.
shield and the drain wire 8 pins
Fold the shield and wind it to the external of the cable. 1 pin
Fold the train line along with the shield.
And then, Cut neatly except for the leaving 11 mm.
Crimping
3
Introduction
4
Chapter 1. Configuration
1.1 Overview
1.1 Overview
1) The system consists of a Processor unit, Monitor unit, Control unit and
Transceiver/Antenna unit. Communication between Transceiver/Antenna unit and
Processor unit, and Control unit by means of serial data (RS-422)
2) The ARPA and the Video plotter functions are incorporated in the SPU board as
standard.
3) The ARPA can acquire a maximum of 100 targets, and AIS can handle a maximum
of
1,000 targets.
4) The video signal for display complies with the DVI (Digital Visual Interface)
standard.
5) The system also has Inter-switch function using the LAN.
6) The antenna cable is a new type RW9600 (13C+2C2V), and the previous type
(24C+2C2V) is not compatible.
7) The I/O terminal block is assembled on the TB board in the Processor unit.
8) Other than the Antenna radiators are not compatible with existing radar systems.
MU-201CR (20.1 inch)
MU-231CR (23.1 inch)
Antenna unit (Monitor unit)
Antenna unit
HUB-100
(HUB)
Transmission
Model Display Unit Band Remarks
Output
FAR-2137S 20.1 inch S-band 30 kW 2 unit type TR up
FAR-2837S 23.1 inch S-band 30 kW 2 unit type TR up
FAR-2837SW 23.1 inch S-band 30 kW 3 unit type TR down
FAR-2827W 23.1 inch X-band 25 kW 3 unit type TR down
FAR-2137S-BB S-band 30 kW 2 unit type TR up
FAR-2117/2127 20.1 inch X-band 12/25 kW 2 unit type TR up
FAR-2117/2127-BB X-band 12/25 kW 2 unit type TR up
FAR-2817/2827 23.1 inch X-band 12/25 kW 2 unit type TR up
1-1
1.1 Overview
1.1.1 Samples
1. FAR-2127 and FAR-2827
Monitor unit
Antenna unit
(MU-201 or 231CR)
DVI
Antenna unit
Monitor unit
(MU-201/231CR)
ANT
Power
(3 phases) Power (AC)
RW-9600
ANT Power (AC)
DVI
Power (AC)
1-2
1.1 Overview
3. FAR-2827W
Antenna unit
MPYCY-19 Waveguide
Monitor unit
Transceiver unit
(MU-231CR)
(RTR-081)
Power (AC)
RW-9600
DVI
4. FAR-2837SW
Antenna unit
ANT Power
(3 phases) Waveguide
Monitor unit
Transceiver unit (MU-231CR)
ANT power (AC) (RTR-082)
Power (AC)
RW-9600
DVI
1-3
1.1 Overview
1.1.2 Inter-switch
For example, when Processor units are connected with the LAN via Hub, each
Processor unit can control the other Transceiver unit. Maximum eight Processor/Display
units can be controlled via Hub as Fig.1.1.6, and any of four Transceiver units are
selected from a Processor/Display unit by clicking the icon of ANT-X.
“X” means a radar number, for example, when switching the radar from No.1 to No.2,
operations for GAIN, STC, FTC and Range change are interlocked with each other and
can operate from either side. When connecting with the Card interface (CU-200), you
can read/write/share the data from respective Radars.
This Inter-switch function is executed by using the IP address associated with the Radar
number. Each Radar number can set on [Menu] -> 0 -> 4:RADAR NO., note that The
RADAR NO. 1 to 4 are Radars (with Antenna unit) and the No.5 to 6 are the monitors
(without Antenna unit).
Monitor x 4
CU-200
LAN: 100BASE-Tx
(Devices are identified by the No.4 FAR-2xx7 series
No.3 FAR-2xx7 series
IP address.)
1-4
1.2 Configuration
1.2 Configuration
1.2.1 System configuration table
Table 1.2.1(1/3) System Configuration
1-5
1.2 Configuration
1-6
1.2 Configuration
1-7
1.2 Configuration
DVI-D Monitor
- MU-201CR
Option (5/10m) - MU-231CR
GYRO 25msec
GC-10 or
AD-100(AD Format)* DVI-D Monitor
- MU-201CR
HDG Sensor(IEC61162-2)* *AD-100 or HDG Sensor (5/10m) - MU-231CR
LOG(IEC61162-1) RS-232C
RPU-013 PC
NAV(IEC61162-1)
Option Network
(100Base-T) RPU-013
RGB EXT. Monitor
RGB Buff
R/G/B/V/H
(75 ohm Co-X x5) DSUB-BNC RPU-013
VDR Convertor
(Max. 100m) HUB-100 Radar No. 1 - 8
(Max. 8 port)
Card I/F
(CU-200)
2 slots
AC PWR 100VAC
100/220VAC 03P9339-
A/B/C/D
440VAC
RU-1803 IEC61162-2
100VAC U-AIS
DC PWR
24VDC or
03P9338-
A/B/C/D LAN
100/220VAC
RU-3424 ECDIS
24VDC INS
Track control (ECDIS)
1-8
1.2 Configuration
1.2.3 Cable
1. Cable length for each unit
FURUNO
RW-9600
15/30/40/50m, Max. 100m 10/20/30m
HUB-100
(LAN cable: FR-FTPC-CV )
DVI-D
5/10m MU-201CR
DVI-D/D MU-231CR
SIGNAL LINK 5M/10M 10/20/30m
RPU-013
(LAN cable: FR-FTPC-CV )
DVI-D
NETWORK
10/20/30m
(LAN cable: FR-FTPC-CY)
CU-200
10m (Power cable: MJ-A3SPF0015-100)
RPU-013
J602: J501: J502: J501:
Key Prossessor Remote Prossessor
RCU-014
RCU-016
1.5/10/20/30m Power 1.5/10/20/30m
SW
(XH10P-W-5P) (XH10P-W-5P-A)
or
J521: J522:
Prossessor Remote
RCU-015
Power
1.5/10/20/30m SW
Max. 31.5m
2. LAN cable
The cross cable is used when RPU-013 and RPU-013 are connected or RPU-013 and
CU-200 without a HUB are connected.
When the HUB-100 is used, either a straight cable or cross cable can be used between each
unit. All the ports of HU-100 are automatically recognized straight/cross cable (Auto-MDIX).
SPU p.c.b
LAN
100Base-Tx NET-100
8 ports
SPU p.c.b
LAN 100Base-Tx LAN 100Base-Tx No.x FAR-2xx7 series
NET-100 HUB-100
cross cable cross cable
CARD CPUp.c.b
or or
straight cable straight cable NET-100
No.x FAR-xx7 series LAN
CU-200
1-9
1.2 Configuration
Terminal p.c.b
RJB-001 RJB-001 Terminal p.c.b
RW-9600 TB-1 TB-1 RW-9600 TB801
J613
1. TX-HV 1. TX-HV DPYCY-6 1 1. TX-HV
2. N.C 2. N.C 2 2. N.C
3. GND DPYCY-6 3 3. 24V(+)
J610
1. 24V(+) 4. 24V(+) 4 4. 24V(-)
2. 24V(-) 5. 24V(-) 5 5. Motor(+)
DPYCY-6
3. Motor(+) 6. Motor(+) 6 6. Motor(+)
4. Motor(+) 7. Motor(-) 7 7. Motor(-)
5. Motor(-) 8. Spare 8 8. Motor(-)
6. Motor(-) 9. Spare 9 9. SPU RF D-A
TTYCYS-4
7. SPU RF D-A 10. SPU RF D-A 10 10. SPU RF D-B
8. SPU RF D-B 11. SPU RF D-B 11 11. RF SPU D-A
9. RF SPU D-A 12. SPU SPU D-A 12 12. RF SPU D-B
10. RF SPU D-B 13. SPU SPU D-B 13 13.Sig. GND
11. Sig. GND 14. Sig. GND 14 14. GND
12. GND 15
15. Spare
TB-2 TB-2 TB802
RG-12/UY
J609
1. IF Vido in 1. IF-OUT 1 1. IF Vido in
2. GND 2. GND 2 2. GND
RW-9600 RW-9600
Max. 15m 70 - 270m Max. 15m
1. Motor 3ph u
2. Motor 3ph v
(Max. 50m)
DPYCY-1.5
3. Motor 3ph w
RPU-013
J604 1. +12V
2. ANT ON N
RJB-001 RJB-001 Terminal p.c.b
Terminal p.c.b
RW-9600 RW-9600
Max. 15m 70 - 270m Max. 15m
1-10
1.2 Configuration
The optional De-icer must be incorporated in the factory. (not a field job)
The De-icer power is 100 VAC, 1 φ , 50/60 Hz. When the De-icer power is except for 100
VAC, a transformer unit (RU-3305) is used.
When mounting a performance monitor (PM-31), change the Gearbox cover with the
PM-31. The antenna revolution speed depends on the type of the Gearbox and the PWR
board of the Processor unit.
FURUNO
PM-31
For De-Icer
DPYCY-1.5
RW-9600
100VAC 1 50/60Hz
100/110/200/220VAC
1 50/60Hz RU-3305
(Transformer)
RU-3305
Scanner
RPU-013
1-11
1.2 Configuration
The De-icer must be incorporated in the factory. (not the field job)
When mounting a performance monitor (PM-31), change the Gearbox cover with the
PM-31.
The Gearbox and Transceiver unit (RTR-081) are connected by a waveguide. Install the
Transceiver unit in such a way as to minimize the length of the waveguide for minimizing
the signal loss by the waveguide. And, it has to keep more than specified bent radius
because the loss becomes greater.
FURUNO
PM-31
DPYCY-1.5
For De-Icer
Wave guide
- WRJ-9 or
MPYCY-19
100VAC 1 50/60Hz
- FR-9
100/110/200/220VAC
1 50/60Hz RU-3305 Length of Waveguide:
. (Transformer)
Recommended dimension is less than 30 m.
T/R unit Specification of bend radius for FR-9
RTR-081 - E side radius: more than 200 mm
- H side radius: more than 400 mm
- Torsion: 10 deg./m or less
RW-9600
Scanner
RPU-013
1-12
1.2 Configuration
The De-icer must be incorporated in the factory. (not the field job)
The performance monitor (PM-51) is built in the Gearbox. The PM-51 can be mounted
in the field job. The antenna revolution speed depends on the type of the Gearbox and
the PWR board of the Processor unit.
Use a transformer unit when the specifications of Antenna motor power are different
from ship’s power supply.
The Antenna motor power is supplied to the Gearbox via the Power supply unit,
PSU-007. The PSU-007 is composed of Relays and Thermal switches.
A note should be taken that an Antenna radiator; SN-30AF (10 ft) of 21/26 rpm does not
adapt with the IMO radar in terms of the bearing discrimination. However, the HSC is
adapted.
SCANNER UNIT
1-13
1.2 Configuration
FURUNO
Transformer unit
DPYCY-1.5
For De-Icer
TPYCY-2.5(Motor)
100VAC 1 50/60Hz
Max. 100m
100/110/200/220VAC
RW-9600
1 50/60Hz RU-3305
(Transformer)
Power ON
220VAC
(Transformer)
(Transformer)
380VAC 3 50Hz
440VAC 3 60Hz
Transformer
Input Output Gear box (ANT motor) / rpm
unit
RU-5693 110 VAC 3 φ 60 Hz 220 VAC 3 φ 60 Hz RSB-101 (RM-9520) / 45
RU-6522 220 VAC 3 φ 50 Hz 200 VAC 3 φ 50 Hz RSB-098 (RM7398) / 21
440 VAC 3 φ 60 Hz 220 VAC 3 φ 60 Hz RSB-101 (RM-9520) / 45
RU-5466-1
440 VAC 3 φ 50 Hz 200 VAC 3 φ 50 Hz RSB-098 (RM7398) / 21
1-14
1.2 Configuration
As for the description on the De-icer and Performance monitor; PM-51, the same as
given in the above clause “3. FAR-2x37S” is applied. The Gearbox and Transceiver unit;
RTR-082 are connected by a waveguide. Install the Transceiver unit in such a way as to
minimize the length of the waveguide for minimizing the loss of the waveguide. And, it
has to keep more than specified bent radius because the loss becomes greater.
FURUNO
Length of waveguide:
LHPX-20D-ASSY
For De-Icer
DPYCY-1.5
TPYCY-2.5(Motor)
MPYCY-12(Cont)
(Transformer)
(Transformer)
Scanner
440VAC 3 50Hz RU-5466-1
200VAC
1-15
1.3 Specifications
1.3 Specifications
1.3.1 TR unit and Antenna Radiator
Table 1.3.1 List of Transceiver Unit
Type of Antenna
XN-5A XN-12AF XN-20AF XN-24AF SN-30AF SN-36AF
Radiator
2817 2817
2817
2827 2827 2137S 2137S
2127-5A 2827
FAR- 2117 2117 2837S 2837S
2827-5A 2117
2127 2127 2837SW 2837SW
2127
2827W 2827W
Antenna length 10 ft 4 ft 6.5 ft 8 ft 10 ft 12 ft
Rotation diameter 334 cm 140 cm 220 cm 270 cm 320 cm 386 cm
TX frequency 9.410 MHz 9.410 MHz 9.410 MHz 9.410 MHz 3.050 MHz 3.050 MHz
Horizontal beam width
0.75 deg. 1.9 deg. 1.23 deg. 0.95 deg. 2.3 deg. 1.8 deg.
(-3 dB point)
Vertical beam width 20 deg. 20 deg. 20 deg. 20 deg. 25 deg. 25 deg.
Side lobe
(maximum value) -28 dB -24 dB -28 dB -28 dB -24 dB -24 dB
Less than +10 deg. -32 dB -30 dB -32 dB -32 dB -30 dB -30 dB
More than +10 deg.
Gain 32 dB 27.5 dB 30.0 dB 31.5 dB 26.2 dB 26.8 dB
Radiator Slotted waveguide array
Polarization Horizontal
1-16
1.3 Specifications
Note:
- B.W (Band Width):
IF frequency: Receiving bandwidth of 60 MHz.
- PRF (Pulse Repetition Frequency):
The Repetition Frequency is not constant to avoid Radar interface from other radars.
The Jamming range is approximately ± 10 % of the Repetition Frequency. When the
Antenna is stopped, the Repetition Frequency is constant.
- ARPA 32NM:
The Repetition Frequency is changed when the ARPA tracking distance is set to
32 NM on [Menu] -> 0 -> 6 -> 9: MAX RENGE.
- 2nd: Repetition Frequency of the 2nd trace mode
The Repetition Frequency is changed when the setting on [Menu] -> 1 -> 1: 2ND
ECHO REJ is ON.
1-17
1.3 Specifications
Range scale 8 12 16 24 32 48 96
Range ring 2 2 4 4 8 8 16
The Number of rings 4 6 4 6 4 6 6
Note:
The ranges in the meshed frames are not available for IMO/A type. For changing the
Model Type, change the setting of “IMO/A, B, C and W” on [Menu] -> 0 -> 4 -> 7.
Type.
1-18
1.3 Specifications
MU-231CR/MU-201CR: RPU-013:
Monitor Unit Input Voltage Processor Unit Input Voltage (100 knot)
Model: FAR-
24 VDC 100 - 115 VAC 220 - 230 VAC
24 VDC 100 - 230 VAC
24/42 rpm* 24/42 rpm* 24/42 rpm*
2117 0.7 A 7.6/8.5 A 2.6/3.0 A 1.6/1.7 A
2.3 A
2127 (100 VAC) 8.8/9.7 A 3.0/3.4 A 1.8/1.9 A
2817 0.9 A 7.6/8.5 A 2.6/3.0 A 1.6/1.7 A
3.2 A
2827 (100 VAC) 8.8/9.7 A 3.0/3.4 A 1.8/1.9 A
2117-BB 7.6/8.5 A 2.6/3.0 A 1.6/1.7 A
2127-BB 8.8/9.7 A 3.0/3.4 A 1.8/1.9 A
2137S 0.7 A (100 VAC) 3.0 A 1.5 A
2837W 3.2 A 1.6 A
2837S 0.9 A (100 VAC) 3.0 A 1.5 A
2837SW 3.0 A 1.5 A
2137S-BB 3.0 A 1.5 A
1-19
1.4 List of Functions
1-20
1.4 List of Functions
1-21
1.4 List of Functions
- Vector time
OFF/30 S/1 M/3 M/6 M/15 M/30 M
Vector can be changed between REL and TRUE.
- Past position display:
10 points/Target selectable
- Activating the guard zone
No.1 Triangle guard zone:
Range between 3 and 6 NM
No.2 Triangle guard zone:
ARPA Within 24 NM or 32 NM
- or Polygonal guard zone:
10 points or less within a range of
24/32 NM
- Tracking range:
0.1 to 32 NM.
- Maximum Antenna revolution
42 rpm (X-band) or 45 rpm (S-band)
- Trial maneuvering
- Tracking parameter:
- Initial vector presentation time
60 sec. or less, selectable
- Data display
Range/Bearing/Course/Speed/CPA/TCPA/BCR/
BCT
- Reference target vector
3 points can be inputted.
- Maximum number of Target:
1000 points
- Vector time
OFF/30 S/1 M/3 M/6 M/15 M/30 M/
Vector can be changed between REL/TRUE.
AIS display
- Past position display
10 points/Target
- Data Display
Range/Bearing/Course/Speed/CPA/TCPA/BCR/B
CT/HDG/ROT
1-22
1.4 List of Functions
1-23
1.4 List of Functions
Note:
See chapter 4 for details of setting radar type IMO/A/B/C/W.
1-24
Chapter 2. Location of2.1 Parts
Processor Unit
F1
100 VAC: 10 A (125 V)
220 VAC: 5 A (250 V)
LAN Port (RJ45) for 24 VDC: 20 A (125 V)
FAR-21X7/28X7,
Network Hub (HUB-100),
CARD I/F (CU-200) or
INS
2-1
2.1 Processor Unit
HV9017 Board
HV-9017A: 12 kW (330 V)
HV-9017B: 25 kW (550 V)
SPU Board
03P9337
PRW Board
AC Power Supply:
03P9339A/B/C/D
DC Power Supply:
03P9338A/B/C/D NET Board
NET100 基板
* 03P9338A/B: 12V SPEC 03P9332
03P9332
(No shipping.)
2-2
2.1 Processor Unit
LAN Port
(100 BASE-T)
GND Terminal
Hinge
** Possible to separate
between bottom and
GC-10 Board upper chassis.
(64P1106A, Optional)
Terminal Board
GYRO Input Terminal
(03P9342)
(Optional)
2-3
2.1 Processor Unit
CR8
(Blinks every Mounting part
0.5 second.) MAIN CPU of NET-100.
(U21)
ARPA CPU
(U74)
DVI-D J204
S2
(Reset SW)
DVI-D J205
DRW CPU
(U19)
2-4
2.1 Processor Unit
100BASE-T
(RJ-45)
CR1 (LED-B)
(Blinks when LAN port is used.)
CR2 (LED-A)
(Lights when data flows through LAN port.) ** This board is also used in CU-200.
2-5
2.1 Processor Unit
CR23 (GRN)
CR21 (RED)
Suffix mark
2-6
2.1 Processor Unit
TP11 (12 V)
TP18
TP19
J104
CR63 (MTR)
TP9
CR64 (RF)
TP4(PR5 V)
TP5 (PR5 V)
TP7
R21 (OVER)
TP6
J101
2-7
2.1 Processor Unit
J105 J106
R106
TP19
TP14(32 V)
TP18
J104
CR63 (MTR)
TP9
CR64 (RF)
CR65 (Tx_HV)
TP8 J103
R88 (12 V) TP1 (S_5 V)
CR23 (1N-ER)
TP3 (PR12 V)
TP7
TP10 (GND)
TP12 (-14 V)
J101
TP6 TP2
2-8
2.1 Processor Unit
J651 (HV)
12 kW: 310-350 V
25 kW: 520-580 V
PSU PSU
J613 (SCANNER)
J604 (PSU)
J618 (To Slave 2)
J606 (HEADING)
(IEC-61162-2) J656
J619 (ECDIS)
J603 (GC-10)
J611 (AIS)
J606 (NAVIGATOR)
J655
J622 (KEY)
2-9
2.1 Processor Unit
a..
b..
L=20 mm 231-131
L=19 mm
734-230
c.
2-10
2.2 Scanner Unit
2-11
2.2 Scanner Unit
J921 (TX_HV)
IF Board (03P9335A)
PM-31 Connection
J921 (HV)
2-12
2.2 Scanner Unit
PM-31 Antenna
(03P9361)
PM-31/B3RX1626
2-13
2.2 Scanner Unit
Motor Type Antenna Speed Scanner Unit Fig. 2.2.6 Antenna Motor
D8G-516 24 rpm RSB-096
D8G-571 42 rpm RSB-097
Gear Retainer
Rotary Joint
2-14
2.2 Scanner Unit
Heading Lead SW
J916
(HD/B.P) B.P GEN Board (03P9347)
J917
3 Units are used.
TB804 (FAR-2837SW: RTR-082)
(Antenna Motor Power Supply)
2-15
2.2 Scanner Unit
MIC (RU-9601)
2-16
2.2 Scanner Unit
IFAMP OUT
(J823) J3
1. Mag.Cur
3. GND
CR9
(RTR-078 and -079 use the board.) (Blinks every second,
CPU (U19) operations)
Fig. 2.2.11 RFC Board, 03P9346A
J833
R62 (ADJ)
(MIC
マグネトロン TUNNIING, +32
V at J833#6)
MG4010 or MAF1425B
03P9348A: 12 kW
03P9348B: 25 kW
03P9348C: 30 kW (S-band)
R57 (-12V at J833-#1)
2-17
2.2 Scanner Unit
60 MHz IF Output
VR1 (Power)
Used to adjust magnetron
current at factory.
03P9244A: X band 12 kW
03P9244B: X band 25 kW
03P9244E: S band 30 kW
2-18
2.2 Scanner Unit
MD Board
(03P9244B)
Pulse Transformer
(RT9023)
Magnetron
(MG5436)
MD Board
(03P9244A)
Magnetron
(MG4010 or MAF1425B) Pulse Transformer
(RT9025)
2-19
2.2 Scanner Unit
TB Board (03P9349)
Waveguide Joint
De-Icer
Heading Lead SW
Drive Gear
TB804
(Antenna Motor Power Supply)
2-20
2.2 Scanner Unit
Gear Retainer
Waveguide
2-21
2.2 Scanner Unit
Waveguide Joint
RF Unit
TB Board (03P9349A)
Cable Entry
Added 2P connector:
IF AMP Board
Ver.33A and after
(03P9335A) RFC Board (03P9346A)
MIC: RU-9601
or RU-9603 TR Limiter
2-22
2.2 Scanner Unit
MD Board
(03P9244B)
Fig. 2.2.21 (a) RTR-081 RF Unit with Shield Cover Removed (1)
Fig. 2.2.21 (b) RTR-081 RF Unit with Shield Cover Removed (2)
2-23
2.2 Scanner Unit
IF AMP Board
(03P9335B) with
shield cover removed
MIC (RU-9427)
TB Board (03P9349A)
Antenna Motor
(RM-7398)
2-24
2.2 Scanner Unit
TB Board (03P9349A)
PM-51
Diode Limiter
2-25
2.2 Scanner Unit
MSS-7497 Board
2-26
2.2 Scanner Unit
Magnetron (MG5223F)
MD Board (03P9244E)
2-27
2.2 Scanner Unit
Antenna Motor SW
Circulator
2-28
2.2 Scanner Unit
Antenna Motor
TB Board
Fig. 2.2.32 RSB-098 Antenna Motor
2-29
2.2 Scanner Unit
Antenna Switch
Waveguide Flange
2-30
2.2 Scanner Unit
2-31
2.2 Scanner Unit
MD Board (03P9244E)
TB Board (03P9349A)
IF AMP Board (03P9335B)
with a shield cover removed
2-32
2.2 Scanner Unit
MD Board (03P9244E)
Circulator
MIC Wiring
Antenna Motor Breaker
Shield Cover
(Current Adjustment)
MIC
(RU-9427)
TR Limiter
2-33
2.3 Monitor Unit
534 (598)
Hanger
4-( φ )13
454 (505)
35° 409
(451)
Hanger Stay
2-M10 x 30
VIDEO IN
(DVI-D)
Fuse
100 VAC: 2 A
220 VAC: 2 A
24 VDC: 6 A
2-34
2.3 Monitor Unit
Fuse (2 A)
Power Supply DVI I/F Board
AC: DC-DC Board (03P9359) (SLB-FRN3-A)
DC: PWR Unit (RKW-12-13RE)
Noise Filter
LF-205A (AC)
MXB-1206-33 (DC)
LED1 (Always ON)
LCD Board
(201PW023-H)
Inverter Board
(210PW021-C)
LCD Unit
(NL128102AC31-02)
2-35
2.3 Monitor Unit
Fan
(MMS-06C12DS 12VDC 0.17A)
FIL Board
(03P9360)
Power Supply
AC: DC-DC Board (03P9359)
DVI I/F Board
DC: PWR Unit (RKW-12-13RE)
(BSM-501 FN1)
Noise Filter
LF-205A (AC)
MXB-1206-33 (DC)
LCD Unit
(FLC59UXC8V-04)
Inverter Board
(NA19002-4241)
LCD Board
(NA21808)
2-36
2.4 Control Unit
Left Button
Wheel
Right Button
Power Switch
Trackball
2-37
2.4 Control Unit
S36 Function
SYSTEM FAIL ALARM
JP1 #1
(ON: Output from J507)
Open (Write Program) RELAY STATUS
Short (Ordinary) #2
(ON: Reversed polarity of the above signal)
#3 Not used
#4 Not used
2-38
2.4 Control Unit
Power Switch
RCU-015: Provided
RCU-016: Not provided
XH10P-W-5P-A
L=1.5/10/20/30 m
J521 (PROCESS0R)
- RCU-013 Connector CR11(U5 CPU RUN)
- RCU-016 connects with RCU-015 Blinks every second.
(Remote Panel.)
トラックボール部
JP1
Open (Write Program)
Short (Default)
J527 (SYSTEM FAIL)
2-39
2.5 Optional Unit
LAN Port
(100BASE-T)
Mini Card Slot (x2) for
C-MAP, NAVIONICS,
and FURUNO chart card. Power Supply
(12 VDC)
Port A Port B
S1 (DIP SW)
#1: INIT #3: IP1
#2: IP2 #4: IP0
CR2 (U12 CPU RUN,
When two CU-200s are installed, on Blinks every second.)
S1-#4 2nd units is set to ON.
NET-100 Board
(03P9332)
2-40
2.5 Optional Unit
100 – 230VAC
Fuse (1 A)
Port Number: 1 to 8
(Lights when in use.)
Link/Act
FDx/Col
10M/100M
RJ45
(a)
03P9364
2-41
2.5 Optional Unit
Fuse (2 A)
A J5 B A J4 B
(Jumper) (Jumper)
A J6 B
2-42
2.5 Optional Unit
SW1
(Gear ratio, Type of
JP2
gyrocompass and
(Stator Voltage)
frequency)
TP1:+5.2V
JP3 JP9
(Rotor Voltage)
J1
(Type of gyrocompass) SW2
(Rotor Voltage, Stator
Voltage, Self-test,
NMEA Transmitting
interval, CPU reset)
J5
(Rotor Signal Input)
J7-12:
J4 (Stator Signal Input) Data Output Port 1-6
J7, J8, J9 (25 ms)
J10, J11, J12 (200 ms)
J6
(NMEA Output Port)
CR21 (CPU RUN,
OK when blinking)
2-43
2.5 Optional Unit
2-44
2.6 Radar Console
1100
960
570
Fig. 2.6.2 RCN-003, Side View Fig. 2.6.3 RCN-003, Rear View
2-45
2.6 Radar Console
Mounting of CU-200
Mounting PSU-007
TB Board
Power Supply Terminal Board
2-46
2.6 Radar Console
PSU-007
2-47
2.6 Radar Console
790
788
400
Mounting CU-200
Cable Entry
2-48
2.6 Radar Console
TB Board
Ground Terminal
Fig. 2.6.11 RPU-013, Open View (1/2) Fig. 2.6.12 RPU-013, Open View (2/2)
2-49
Chapter 3.13.Overview
Menu Tree
of Menu Operation
Note:
1. When the “+” cursor is changed, it shows any selection is made.
The menu selection screen has a timeout of 30 seconds and the Menu box disappears.
2. After you change the some setting, wait for six seconds before turning off the power.
Otherwise, it is not saved.
3. There is a Menu guidance box (xxx/xxx) in the lower right of the screen.
090
100
ARP,
110
AIS DATA BOX
120
160
ALARM2 ALERT BOX
180 170 CU/TM Guidance
VRM1>3.682NM< RESET
VRM2 5.221NM
ALARM TARGET
ACK
CURSOR Box
DATA & ACQ MENU
Left-click Right-click
3-1
3.1 Overview of Menu Operation
3-2
3.1 Overview of Menu Operation
AIS Targets
Expanded data
Click the left button on the
data display area.
ARPA Targets
3-3
3.1 Overview of Menu Operation
Data
Input Data Display Remarks
Display
Select AD-10 or SERIAL in [HDG] box
HDG HDT, AD-10 xxx.x deg T (TRUE)
menu
VBW>VHW xx.x kt WT/Log Select LOG (WT) in [SPD] box menu
Select LOG (WT) in [SPD] box menu
VBW>VHW
xx.x kt WTC/Log Select SET DRIFT -> ON in [SPD] box
Set and drift entry
menu
VBW xx.x kt BT/Log Select LOG (BT) in [SPD] box menu
VTG>RMC xx.x kt BT/GPS Select GPS in [SPD] box menu
SPD
When REF is selected in [SPD] box
Reference speed setting xx.x kt BT/REF menu and REF (reference target) is
acquired
Manual xx.x kt WT/MAN Select MANUAL in [SPD] box menu
Select SET DRIFT -> ON in [SPD] box
Set and drift entry xx.x kt WTC/MAN
menu
VBW
(When LOG (WT) or Show the speed in the X-axis direction
LOG (BT) is selected in of the ship speed on two axes. Speed in
the SPD Menu. the Y-axis direction is a HDG element
VTG>RMC and display in the “SPD.”
SB xx.x kt
(Calculated from
SB: Starboard.
VTG>RMC when GPS
Port side speed is displayed with
is selected in the SPD
minus sign.
menu.)
COG VTG>RMC COG Displays NAV Data (GPS)
Select GPS-1, 2 or LAN in the [OS
SOG VTG>RMC SOG
POSN] box menu.
PPS (GPS PPS mode, fix valid)
RTK (Real Time Kinetic.
Satellite system used in RTK
GGA mode with fixed integers)
Switching by Mode indicator in the
F-RTK (Float RTK. Satellite
POS sentence.
system used in TRK mode with
floating integers)
GGA> RMC > GLL GPS
GGA> RMC >GLL DGPS
Manual DR
3-4
3.2 Box Menu
Pop-up
Box Cyclic change Description
Menu
The range of 4, 8, 16 and 32 NM are not
RANGE UP/DOWN of RANGE
available on the IMO and A type radar.
DISPLAY DISPLAY>DISPLAY+PLOTTER PLOTTER mode is not available on the
MODE > PLOTTER IMO and A type radar.
HEAD UP RM >
HEAD UP TB RM>
PRESENTATION
COURSE UP RM>
MODE
NORTH UP RM>
NOTRH UP TM)
Note:
ANT1>ANT2>ANT3>
ANT [Menu] -> 0 -> 4 -> 2, 3 YES
ANT4>SUB
[ANT] box menu -> 8
PULSE PULSE NARROW to
LENGTH PULSE WIDE
The following items can set in each
Picture menu.
- INT REJECT
- ECHO STRATCH
PICTURE1> PICTURE2> - ECHO AVERAGE
PICTURE3>PICTURE4> - NOISE REJ
PICTURE NEAR>FAR>NEAR BUOY> - AUTO STC YES
FAR BUOY>ROUGH SEA> - AUTO RAIN
SHIP>HARBER>COAST - VIDEO CONTRAST
- SEA CONDITION
- ANT HEIGHT
- STC RANGE
- PULS WIDE
Note:
MARK MARK, WPT YES
Specify in the [MARK] box menu
IL1 is displayed in full lines and IL2 in
dotted lines. The Line setting of range
and bearing is performed with the EBL
IL (Index Line) IL1> IL2
and VRM or wheel.
Note:
[Menu] -> 2 -> 4, 5, 6
You can make all the brilliance settings
BRILL1> BRILL2> BRILL3> of the pop-up menus in this box. Four
BRILL YES
BRILL4> types of settings are available in any
desired combination.
BRILL BAR
Cont’d
3-5
3.2 Box Menu
Cont’d
3-6
3.2 Box Menu
Cont’d
3-7
3.2 Box Menu
OFF>00:15>0030>01:00> -- >
TRAIL MODE Can be set for each 30 seconds. YES
30:00>CONT
When this function is turned on, the
VRM 1, 2 VRM ON/OFF
VRM is displayed.
While CU is active, CU is reset by
clicking the lift button. While TM is
CU/TM RESET
active, TM is reset by clicking the lift
button.
Alarm acknowledge; silence the audible
ALARM ACK
alarm
HDG [HDG] box menu is displayed. YES
SPD [SPD] box menu is displayed YES
OS POSN [OS POSN] box menu is displayed YES
On the bases of the radar ANT position
or conning position; changes the origin
RFE POINT ANT POSN>CONN POSN point of range ring and cursor data.
Note:
Position entered in the [Menu] -> 0 -> 5.
Note:
ARPA OFF/ON [ARPA] Menu,
ARPA YES
(ON:MANU, AUTO MANU) [Menu] -> 4, [Menu] -> 0 -> 6
[Menu] -> 0 -> 8 -> 4
Turns on and off AIS target display.
When [Menu] -> 4 -> 8: AIS
FUNCTION setting is turned off, this
AIS AIS DISPLAY ON/OFF YES
box display is erased.
Note:
[Menu] -> 4 -> 6, 7, 8, 9
Incoming AIS message, an envelope
mark is displayed when “3. AUTO DISP
AIS MSG Arrival
MSG” setting in the [AIS] box menu is
turned on.
VECTOR TRUE>
VECTOR REL
Sets the vector mode and vector time of
VECTOR 30 SEC>1 MIN>2 MIN>
the ARPA and AIS.
3 MIN>6 MIN>12 MIN>
15 MIN>30 MIN
Sets the interval of past position plotting
time of the ARPA and AIS target.
OFF>30 SEC>1 MIN>2 MIN>
PAST POSN Note:
3 MIN>6 MIN>
[Menu] -> 4 -> 5-> 4, 5
[Menu] -> 4 -> 6-> 5, 6
When clicking [CPT LIMT] box icon,
CPA LIMIT CPA ON/OFF
[CPA] and [TCPA] boxes are added.
0.5 NM> ---- > 20 NM
Note:
CPA (0.5 – 10 NM/0.5 NM,
[Menu] -> 3 -> 6 to 9
10 – 20 NM/1 NM step)
1MIN> --- > 60 MIN Note:
TCPA LIMIT
(1 min step) [Menu] -> 3 -> 6 to 9
The guidance box corresponds to the
Guidance [ xxx / xxx ]
right and lift click operation.
3-8
3.2 Box Menu
3.2.2 Content
[HDG]
[OS POSN]
[OS POSN MENU]
1 NAV AID
GPS1/GPS2/
DEAD RECKONING*/
LAN
2 MANUAL L/L
00 ° 00.00 N
000 ° 00.00 W
3 SIO DATA LAN OUTPUT
OFF/ON
3-9
3.2 Box Menu
[SPEED]
[SPEED MENU]
1 SHIP SPEED
LOG(BT)/LOG(WT)/
GPS/MANUAL*/REF*
2 MANUAL SPEED
0.0kt
3 SET DRIFT
OFF/ON*
[TGT LIST]
3-10
3.2 Box Menu
[CURSOR]
[CURSOR MENU]
2
TARGET DATA & ACQ/
TARGET CANCEL/
ARP TGT DATA & ACQ/
TARGET TRACK ON/*
TARGET TRACK OFF/*
REF MARK/
EBL OFFSET
OFFCENTER/
ZOOM/
MARK DELETE/
CHART ALIGN
8
3-11
3.2 Box Menu
[ARP]
1 ARP SELECT
MANUAL 100/
AUTO 25/
AUTO 50/
AUTO 75/
AUTO 100
2 ALL CANCEL
NO/YES
3 REF TARGET VECTOR
OFF/ON
3-12
3.2 Box Menu
[AIS]
[VOYAGE DATA]
1 BACK
2 NAVIGATION STATUS
00
UNDER WAY
USING ENGINE
3 ETA
00/000/0000 00:00
4 DESTINATION
5 DRAUGHT
00m
6 CREW
0000
[STATIC DATA]
1 BACK
TYPE OF SHIP
000
ALL SHIP OF THIS TYPE
CALL SIGN
NAME
EXT GPS ANT POSN
A: 000m B: 000m
C: 00m D: 00m
Cont’d
3-13
3.2 Box Menu
3-14
3.2 Box Menu
[PICTURE]
Optimum picture setting can be made individually according to the sea conditions, for
instance, for seeing a far target or the near target. See the next page for the default setting.
Setting values are not dependant on the type of IMO, A, B C and W.
[PICTURE MENU]
1 INT REJECT
OFF/1/2/3
2 ECHO STRETCH
OFF/1/2/3 [PULSE MENU]
3 ECHO AVERAGE
OFF/1/2/3 1 BACK
2 0.5NM
4 NOISE REJ
OFF/ON S1/S2
3 0.75NM
5 AUTO STC
S1/S2/M1
OFF/ON
4 1.5NM
6 AUTO RAIN
S1/S2/M1
OFF/1/2/3/4
5 3NM
7 VIDEO CONTRAST
S2/M1/M2/M3
1/2/3/4/
6 6NM
A/B/C
M1/M2/M3/L
8 [PULSE]
7 12 -24NM
9 [CONDITION]
M2/M3/L
0 DEFAULT (ENTER X 3)
[CONDITION MENU]
1 BACK
2 SEA CONDITION
1/2/3/4/5
3 ANT HEIGHT
5/7.5/10/15/20/
25/30/ 35/40/45/
more 50 m
4 STC RANGE
+00
Cont’d
3-15
3.2 Box Menu
Pulse Condition
0.5 0.75 1.5 3 6 12-24 Sea STC
NM NM NM NM NM NM Condition Range
PICTURE 1 S1 S1 S2 M1 M2 L 2 +0
PICTURE 2 S1 S1 M1 M2 M3 L 2 +0
PICTURE 3 S1 S1 S2 M1 M2 L 3 +0
PICTURE 4 S1 S1 S2 M1 M2 L 2 +0
NEAR S1 S1 S2 M1 M2 L 2 +0
FAR S1 S1 M1 M3 L L 3 +0
NEAR BUOY S1 S1 M1 M2 L L 2 +0
FAR BUOY S1 S1 M1 M3 L L 2 +0
ROUGH SEA S1 S1 S2 M1 M2 M3 4 +0
SHIP S1 S1 M1 M2 M3 L 2 +0
HARBOR S1 S1 S2 M1 M3 L 2 +0
COST S1 S1 M1 M2 M3 L 2 +0
3-16
3.2 Box Menu
[BRILL]
3-17
3.2 Box Menu
[TRAIL]
[TRAIL MENU]
1 TRAIL MODE
REL/TRUE
2 TRAIL GRAD
SINGLE/MULTI
3 NARROW TRAIL*
OFF/ON
4 TRAIL LEVEL
1/2/3/4
5 TRAIL RESTART
OFF/ON
6 TRAIL COPY
OFF/ON
7 OS TRAIL
OFF/ON
3-18
3.2 Box Menu
[MARK]
[MARK MENU]
3-19
3.2 Box Menu
[ANT INFORMATION]
[ANT INFORMATION]
ANT NO 1
BAND : X-BAND
MODEL: 25 UP
POS : FORE
ANT NO 2
BAND : X-BAND
MODEL: 12
POS : MAIN TOP
ANT NO 3
BAND :
MODEL :
POS :
ANT NO 4
BAND :
MODEL :
POS :
8 SUB MONITOR*
OFF/ON
9 INTER SW PRIORITY
OFF/ON
3-20
3.3 Main Menu Tree
3-21
3.3 Main Menu Tree
1 BACK
Sets whether to display the own ship mark or not. The own
ship mark corresponds to the dimensions of the own ship.
The size of the own ship mark is set in [Menu] -> 0 -> 5 ->
2: LENGTH/WIDE and “REF POINT” is calculated from
the values set in [Menu] -> 0 -> 4 -> 5: RADAR POS and
2 OWN SHIP MARK [Menu] -> 0 -> 5 -> 6: CONNING POS.
If the own ship mark gets smaller than 6 mm on the screen,
it will be represented with a small dot.
Note:
The own ship mark can be changed by specifying the
OWN SHIP MARK in [MARK] box menu -> 2
Sets whether to turn on or off the stern mark. The stern
3 STERN MARK
mark appears opposite to the heading line in a dot line.
Sets whether to display the bearing of the parallel index
line by the true bearing (T) or relative bearings (R.)
Parallel index line:
4 INDEX LINE BEARING
Two index lines (IL) are available. To adjust the index
line interval and bearing, place the cursor on IR and
make adjustments by EBL and VRM.
2 [MARK] Specifies the number of index lines. When one (1) is
5 INDEX LINE selected, “6.INDEX LINE MODE” as listed below is not
displayed.
When “VERTICAL” is selected, you can draw a line
6 INDEX LINE MODE perpendicular to the index line. “HORIZONTLA” is used
to erase a vertical line.
This menu box is displayed when “SERAL, LAN” is set on
[Menu] -> 0 -> 8 -> 5:INS.
7 [INS MARK]
This setting turns on or off the USER CHART, MARK,
LINE, ROUTE and NOTE BOOK from the INS.
This menu box is displayed when [Menu] -> 0 -> 8 -> 5:
INS is set to “OFF.”
7 [BARGE MARK]
Allows the setting of the BARGE MARK and turning on
and off of the display.
8 EBL OFFSET BASE POINT Allows the setting of EBL offset.
9 EBL CURSOR BEARING This is a menu for IMO and A type radars.
This menu is for B and C type radars.
9 [EBL VRM, CURSOR SET] The unit of the VRM and the cursor range can be selected
from NM, SM, km and kyd.
0 RING Sets whether to display the range ring or not.
3-22
3.3 Main Menu Tree
1 BACK
Turns on and off an alarm to be given when the target
2 GURD ALARM MODE
inward or outward the alarm range set in ALARM 1 and 2.
Adjusts the target echo level. It is dependent on the
adjustment of GAIN, STC and FTC. The setting “1”, the
3 GURD ALARM LEVEL
lowest echo detection level, allows detecting very weak
echoes.
This is a function to sound an alarm when the specified
time has elapsed. When you click the left button on the
4 WATCH ALARM [WATCH] box, the counting is reset. The counting is also
reset when you click [ALARM ACK] box or press
3 [ALARM] [ALARM ACK] key.
Adjusts the sound level of alarms outputted from the
5 ALARM SOUND LEVEL Control unit. Alarms are also outputted from the remote
Control unit.
6 [ALARM OUT1] Outputs alarm signals to external equipment when
selected alarms such as Guard Zoon ALARM,
7 [ALARM OUT2]
SYSTEM ERROR and/or etc. Contact signals are
8 [ALARM OUT3]
outputted at the EXT ALM terminals, ALM-1, 2, 3, 4 on
9 [ALARM OUT4] the TB board. Normal Open and Close can also be set.
See Chapter 4 for details.
0 AUDIO ALARM Allows ON/OFF setting of the alarm sound
1 BACK
Sets whether to fix the Guard Zone by the true bearing (T)
2 GURD ZONE STAB
or relative bearing (R.)
Guard Zone No.1 allows the setting of a Guard Zone and
Guard Zone No.2 the setting of a polygon. The setting of
3 GURD POLYGON
Guard Zone No.2 is enabled only when Guard Zone No.1
has been set.
Allows the setting of Trial Maneuver to avoid collision.
Specify the DYNAMIC or STATIC mode and enter the
trial speed rate and trial turn rate corresponding to two ship
speeds. When the [TRIAL] box is active, COG and SOG
entry boxes are displayed. Enter appropriate values in
4 [TRIAL MANEUVER]
respective boxes. Simulation is performed on the basis of
entered data, trial speed rate and trial turn rate. “T” is
displayed during simulation and cleared in 3 minutes. The
entered data is also used for the calculation in [Menu] -> 8
4 [ARP/AIS]
-> 0 -> 3:TURNING LINE.
Allows the setting of symbol color, size, past position color
5 [ARPA SYMBOL]
and past position points of the ARPA.
Allows the setting of symbol color, size, past position
6 [AIS SYMBOL] color, past position points and ROT TAG LIMIT of the
AIS.
If two target symbols of AIS and ARPA are displayed, the
targets are not clearly viewed. To avoid this, AIS targets
7 [FUSION] alone are presented if AIS and ARPA targets meet
conditions set in this menu in terms of the range, bearing
etc.
Turns on and off the AIS functions. If this is set to OFF, the
8 AIS FUNCTION
AIS display in the [AIS] box is turned off.
Setting the condition of lost alarm of AIS
9 AIS LOST ALARM The condition is selected from Active target, All target and
Range. In addition, ALM-1 to 4 is not outputted.
3-23
3.3 Main Menu Tree
1 BACK
Specifies the chart color
2 CHART COLOR
A chart is drawn in PLOTER and RADAR + PLOTER.
3 OWN TRACK INTERVAL
4 OWN TRACK COLOR Sets the track interval and track color of the own ship and
5 TRG TRACK INTERVAL other ship.
6 TRG TRACK COLOR
Sets whether to add the offset value after chart offset to the
5 PLOTTER L/L value of the cursor (+) or not. Offset the L/L position
on the radar map and radar screen.
7 CURSOL L/L ALIGN
During the offset, “ALIGN” is displayed if the cursor icon
is set to L/L. For offset, execute CHART ALIGN in the
[Cursor] menu.
Erases the own track, target track, mark, WPT and NAV
8 [DATA ERASE]
line.
Turns on and off the L/L line, past position, mark land
9 [DISPLAY] density, place name and buoy displayed on the plotter
screen.
[CARD1/2]
1 BACK
Selects the RAM card slot of CU-200.
2 DRIVE SELECT “A” is for the left slot and “B” for the right slot. When the
2nd CU-200 is added, the drives “C” and “D” are added.
Reads data from the RAM card. During reading the data, a
3 [READ CARD] message “WORKING IN PROGRESS” is displayed in
Alert box in the lower right screen.
4 [WR MARK] Each selected data is written on the RAM card.
6 CARD 5 [WR NAV LINE WPT] Mxxxxxxx: WR MARK
6 [WR OWN TRACK] Wxxxxxxx: WR NAV LINE WPT
7 [WR TARGET TRACK] Txxxxxxx: WR OWN TRACK
8 [WR SETTING DATA] Axxxxxxx: WR TARGET TRACK
Sxxxxxxx: WR SETTING DATA
Ixxxxxxx: WR INSTALLATION DATA
9 [WR INSTALLATION DATA] Note:
Writing operation can be checked by the message “WR
CARD DATA” in the Alert box in the lower right screen.
0 NEXT)
Cont’d
3-24
3.3 Main Menu Tree
[CARD2/2]
1 BACK
6 CARD 2 [FILE DELETE] Deletes a selected file stored on the RAM card.
1 BACK
2 DEPT Allows displaying the following data in the data box. To
3 DEPTH GRAPH SCALE display them, turn on the setting in [Menu] -> 9 -> 2 -> 3:
4 DEPTH MARK NAV DATA.
5 CURRENT
6 WIND - DEPTH: DPT>DBT>DBS
7 TEMP - CURRENT: VDR
7 NAV DATA 8 DATE-TIME - WIND: MWV>VWT>VWR
9 LOCAL TIME ADJ - TEMP: MTW
- DATE & TIME: ZDA
- WPT DATA: Selects whether to display the WPT in
the relative bearing or true bearing.
0 WPT DATA
Note:
To display the NAV data, turn on the setting in [Menu] ->
9 -> 2 -> 3:NAV DATA.
[NAV LINE WPT 1/2]
1 BACK
Displays the navigation line received from external
2 NAV LINE DATA
equipment or from registered by the radar.
3 NAV LINE SELECT Selects the Navigation line to be displayed.
4 SKIP NEXT WPT Skips the next waypoint in the navigation waypoints.
5 NAV LINE WIDE Allows the setting of the navigation line width.
8 NAV LINE Allows registering waypoint up to 200 points.
WPT 6 [WPT SET] For registering waypoints, the cursor (+) or L/L are used.
A registered waypoint is also deleted in this box.
7 [WPT LIST] Displays the list of registered waypoints.
Allows the setting of the navigation line based on the
registered waypoints.
8 [NAV LINE SET]
Up to 30 navigation lines can be registered. A registered
navigation line is also deleted in this box.
9 [NAV LINE LIST] Displays the list of registered navigation lines.
Cont’d
3-25
3.3 Main Menu Tree
0 NEXT
[NAV LINE WPT 2/2]
1 BACK
Allows the setting of arrival ranges (presented in a circle)
2 ARRIVAL WPT ALARM of the set waypoints and ON/OFF setting of the alarm.
8 NAV LINE Displays the turning line. The ship data like the trial turn
WPT 3 TURNING LINE rate is registered in [Menu] -> 4 -> 4:TRIAL
MANEUVER.
Displays the registered waypoint number of the mark
4 DISP WPT NO.
displayed.
Displays the registered waypoint name of the mark
5 DISP WPT NAME
displayed.
1 BACK
Sets the kind of data to be displayed in the data box, zoom
OFF/ON (x2, x3) and number of ARPA and AIS.
Related NAV data is displayed by the setting in [Menu] ->
2 [DATA BOX] 7: NAV DATA.
For zooming, place the cursor in the display area, click the
right button, select ZOOM in the [Cursor] menu, place the
cursor at a spot to be zoomed and click the left button.
3 [F1] The specified operation setting can be registered to the [F1]
4 [F2] to [F4] keys and retrieve by pressing the registered key.
5 [F3] For instance, the setting can be as follows;
F1: INT REJECT ON, 2
6 [F4] to
F4: Heading line OFF
Allows specifying the Wheel-Direction and Key-Beep.
And
4 REMOTE KEY:
9 CUSTOMIZE/ - F*-KEY: Normal operation for functions of the
TEST remote control unit
- DISPLAY SELECT: When connected with the
network, [F1] to [F4] keys on the Remote Control
unit are assigned as [ANT X] toggling keys.
5 POP UP GUIDANCE:
When the cursor is placed on a box icon, the trackball
stops moving and a pop-up message shows the
7 [OPERATION]
contents of the icon.
6 OWN SHIP VECTOR:
Allows selecting the display of the own ship vector
(Heading or Course)
7 STERN UP:
A picture is rotated by 180 degrees so as to face the
stern upward on the screen.
8 SHATTLE FERRY: see the next page
The HDG value is added by 180 degrees so as to face
the stern upward on the screen, and the picture is also
turned by 180 degrees.
Cont’d
3-26
3.3 Main Menu Tree
SELF TEST:
Displays the program versions, key test and the serial
input data.
9 CUSTOMIZE/ ARPA TEST:
8 [TEST]
TEST Allow checking ARPA functions with echoes created by
CPU. During the execution, “XX” is displayed in the
display. To terminate, set it to ST-BY. If ARPA test is
executed, the ARPA track is cancelled.
Shuttle Ferry
A shuttle Ferry mode is for the ship that can be steered from the two locations, forward and
reverse. The orientation of radar is presentation rotated at 180 degrees by switching
(contact closure signal) from external equipment via RS-232C port on the TB board of
RPU-013 as shown below.
RPU-013
J601:RS-232C
Normal/Reverse SW
1. NC
Terminal p.c.b 2. RXD
3. TXD
4. NC
5. GND
6. NC
7. NC
8. NC
9. NC
3-27
3.3 Main Menu Tree
1. Main menu
Table 3.3.2 Main Menu
Cont’d
3-28
3.3 Main Menu Tree
1 BACK
2 TARGET ALARM
IN/OUT
MODE
3 TARGET
1/2/3/4
ALARM LEVEL
OFF/6 M/10 M/12 M/15 M/
4. WATCH ALARM
20M
5 ALARM
LOW/MID/HIGH
SOUND LEVEL
1 BACK
2
TARGET ALARM/ All
WATCH ALARM/
GUARD ZONE/
LOST TARGET/
CPA LIMIT/
3 [ALARM]
AUTO ACQ TAG FULL/
6 [ALARM OUT1]
MAN ACQ TAG FULL/
7 [ALARM OUT2]
ARP SYSTEM ERROR/
8 [ALARM OUT3]
AZIMUTH/HEAD LINE/
TRIGGER/VIDEO/
GYRO/LOG/EPFS/XTE/
ARRIVAL WPT/DEPTH/
ALARM ACK OUT
IMO/A
9 ALARM OUT POLARITY NORMAL/INVERT Not
available
Ditto All
IMO/A
9 [ALARM OUT4]
9 ALARM OUT POLARITY NORMAL/INVERT Not
available
0 AUDIO ALARM OFF/ON All
1 BACK
2 GUARD ZONE STAB STAB HDG/STAB NORTH
OFF/STAB GND/
3 GUARD POLYGON
STAB HDG/STAB NORTH
1 BACK
2 TRIAL OFF/STATIC/DYNAMIC All
0 kt 0.00 kt/s
4 [TRIAL MANEUVER] 3 TRIAL SPEED RATE
0 kt 0.00 kt/s
0 kt 0.0°/s
4 TRIAL TURN RATE
0 kt 0.0°/s
1 BACK
4 [ARP/AIS] RED:
RED/GRN/BLU/YEL/CYA/ IMO
2 ARP SYMBOL COLOR
MAG/WHT Not
5 [ARP SYMBOL] available
3 ARP SYMBOL SIZE SMALL/STD/LARGE
RED/GRN/BLU/YEL/CYA/
4 PAST POSN COLOR
MAG/WHT All
5 PAST POSN POINTS 5/10
1 BACK
RED:
6 [AIS SYMBOL] RED/GRN/BLU/YEL/CYA/ IMO/A
2 AIS SYMBOL COLOR
MAG/WHT Not
available
Cont’d
3-29
3.3 Main Menu Tree
Cont’d
3-30
3.3 Main Menu Tree
[DISPLAY (2/2)]
1 BACK
2 NAV LINE (MAP) OFF/ON
5 [PLOTTER] 9 [DISPLAY] All
3 DANGER HIGHLIGHT OFF/ON
4 PROHIBITED AREA OFF/ON
5 BUOY OFF/ON
[CARD1/2]
1 BACK
2 DRIVE SELECT A/B
3 [READ CARD]
1 BACK
4 [WR MARK] 2 NAME
M0000000 All
1 BACK
5 [WR NAV LINE WPT] 2 NAME
6 [CARD] W0000000
1 BACK
6 [WR OWN TRACK] 2 NAME
T0000000
1 BACK IMO
7 [WR TARGET
2 NAME Not
TRACK]
A0000000 available
1 BACK
8 [WR SETTING DATA] 2 NAME All
S0000000
1 BACK
9 [WR INSTALLATION
2 NAME
DATA]
I0000000
0 NEXT
6 [CARD] [CARD2/2] All
1 BACK
2 [FILE DELETE] 1 BACK
1 BACK
3 [CARD INITIALIZE]
2 INITIALIZE START NO/YES
1 BACK
2 DEPTH OFF/m/ft
3 DEPTH
10/20/50/100/200/500
GRAPH SCALE
4 DEPTH MARK 000 m
7 [NAV DATA] 5 CURRENT OFF/ON All
6 WIND OFF/m/s/KT
7 TEMP OFF/ON
8 DATE-TIME OFF/UTC/LOCAL
9 LOCAL TIME ADJ +00:00
0 WPT DATA OFF/REL/TRUE
[NAV LINE WPT(1/2) ]
All
1 BACK
WPT
MARK
OFF/EXT DATA/ :
8 2 NAV LINE DATA INTERNAL DATA/ IMO
[NAV LINE/ WPT MARK Not
WPT] available
3 NAV LINE SELECT --
OFF/ON
4 SKIP NEXT WPT All
0.00 NM
5 NAV LINE WIDTH 0.0 NM
Cont’d
3-31
3.3 Main Menu Tree
1 BACK
2 WPT NO. SELECT 001
3 WPT NAME
6 [WPT SET]
--°--.--- N
4 WPT L/L
---°--.--- E
5 CLEAR DATA NO/YES
7 [WPT LIST] [WPT LIST1 (1/25) - (25/25)] 001 - 200
1 BACK
2 NAV LINE NO. SELECT 01
3 NAV LINE NAME
8 [NAV LINE SET] ――
8 [NAV LINE 4 NAVE LINE ENTRY to
―― All
WPT]
5 CLEAR DATA NO/YES
1 BACK
[NAV LINE LIST]
9 [NAV LINE LIST] 01
(1/30) - (30/30)
0 NEXT
0 NEXT
[NAV LINE WPT (2/2)]
1 BACK
OFF/ON
2 ARRIVAL WPT ALARM
0.00 NM
3 TURNING LINE OFF/ON/REVISED
4 DISP WPT NO. OFF/ON
5 DISP WPT NAME OFF/ON
1 BACK
1 BACK
3 NAV DATA OFF/ON
9 4 ZOOM OFF/2TIMES/3TIMES
[CUSTOMIZE/ STAB GND/ All
2 [DATA BOX]
TEST] STAB HDG/
5 ZOOM DISPLAY
STAB NORTH/
ARP TRACK
6 TARGET DATA 1BOX/2BOX/3BOX/LARGE
Cont’d
3-32
3.3 Main Menu Tree
1 BACK
1 BACK
2
PICTURE/IR/ES/EAV/
NOISE REJ/
ANT SELECT/
PULSE LENGTH/
2 [ECHO]
A/C SEA SELECT/
AUTO RAIN SELECT/
TUNE SELECT/
ANT HEIGHT/
SEA CONDITION/
2ND ECHO REJ/PM/SART
1 BACK
ALARM ACK/STBY TX/
HL OFF/EBL OFF SET/
MODE/OFF CENTER/
CU TM RESET/INDEX LINE/
VECTOR TIME/
3 [STD KEY]
VECTOT MODE/ All
TARGET LIST/TRAIL/BRILL/
MARK/MENU/RANGE UP/
RANGE DOWN/ACQ/
TARGET DATA/
TARGET CANCEL
1 BACK
3 [F1] 2
9
DISP ARP/
[CUSTOMIZE/
DISP AIS/
TEST]
TARGET DATA & ACQ/
PAST POSN INTERVAL/
4 [ARP/AIS] REF MARK/
CPA LIMIT/CPA/TCPA/
GZ1/GZ2/
TARGET LIST SORT/
TRIAL MANEUVER/
ARP-AIS FUSION/
/AIS MESSAGE
1 BACK
2
ECHO COLOR/
BACK COLOR/RING/ TLL:
ALARM1/ALARM2/ IMO/
5 [OPERATION]
WATCH ALARM RESET/ A/B
ZOOM/MARK DELETE/ Not
CHART ALGN/ available
DISPLAY SELECT/
MOB/USER DEFAULT/TLL
PICTURE1/ PICTURE2/
PICTURE3/ PICTURE4/
6 [PICTURE] NEAR/FAR/NEAR BUOY/
FAR BUOY/ROUGH SEA/
All
SHIP/HARBOR/COAST
4 [F2]
5 [F3] Ditto Ditto
6 [F4]
Cont’d
3-33
3.3 Main Menu Tree
1 BACK
2 WHEEL DRIVE NORMAL/REVERSE
All
3 KEY BEEP OFF/LO/MOD/HI
4 REMOTE KEY F*-KEY/DISPLAY SELECT
IMO/A
7 [OPERATION]
5 POP UP GUIDANCE (OFF/ON) Not
available
6 OWN SHIP VECTOR OFF/HDG/COURSE
7 STERN UP OFF/ON All
8 SHAUTTLE FERRY OFF/MODE1/MODE2
9 1 BACK
[CUSTOMIZE/ 1 BACK
TEST] 2 [SELF TEST]
2 START
1 BACK
2 ARP TEST START
3-34
3.3 Main Menu Tree
2. Initialize menu
To access the Initialize Menu, press the [MENU] key five times while pressing the [1: HL
OFF] key.
Cont’d
3-35
3.3 Main Menu Tree
6/12/25UP/
6 MODEL 25DOWN/50/30UP/
30DOWN/60
4 [INSTALL- 7 TYPE IMO/A/B/C/W
All
ATION] 8 ON TIME 000000.0H
9 TX TIME 000000.0H
0 PM GAIN ADJ 0-255
1 BACK
LENGTH 0 m
(0-999)
2 LENGTH/WIDTH
WIDTH 0 m
(0-99)
BOW 0 m
(0-999)
3 SCANNER POSN
PORT 0 m
(99)
BOW 0 m
5 [OWN
(0-999) All
SHIP INFO] 4 GPS1 ANT POSN
PORT 0 m
(0-99)
BOW 0 m
(0-999)
5 GPS2 ANT POSN
PORT 0 m
(0-99)
BOW 0 m
(0-999)
6 CONNING POSN
PORT 0 m
(0-99)
1 BACK
2 TTM OUTPUT OFF/REL/TRUE
3 MAX RANGE 24/32
All
16
4 ECHO LEVEL
(0-31)
5 QV DISPLAY OFF/ON
IMO
6 ARP W/O GYRO OFF/ON Not
available
6 [ARP
1 BACK
PRESET]
800M
2 LAND SIZE
(100-1000)
XN12AF/XN20AF/XN24AF/
3 ANT SELECT XN4A/XN5A/SN30AF/SN36AF/
7 [ACQ PRESET] All
SN4A/SN5A
5 SCAN
4 AUTO ACQ CORRE
(3-10)
1 SCAN
5 AUTO ACQ WEED
(1-5)
Cont’d
3-36
3.3 Main Menu Tree
1 BACK
2 GATE SIZE S/M/L/LL
3 FILTER RESPONSE 1/2/3/4
9 SCAN
4 LOST COUNT
(1-20)
8 [TRACK PRESET] 100 KTS
5 MAX SPEED
(40-150)
6 TRACKING MODE 1/2/3/4
TIME/SCAN/
7 START TIME TGT
50 SEC (20-100)
VECT
/20 SCAN (8-40)
1 BACK
DRIFT=OFF/xxx.x
CPU COUNTER=xxxxx
CPU STATUS=xxxxx
6 [ARP AUTO= x All
PRESET] MAN= x
LOST= x
SCAN= xxxx
MIN HIT= x
9 [ARP E LEVEL= x
SENSOR DATA] 0 NEXT
1 BACK
1= x
2= x
3= x
-------
30= x
31= x
32= x
2 DATA NO
0 DEFAULT
1 BACK
IP 172.031.003.006
RADAR MSK 255.255.000.000
GTW 000.000.000.000
IP 172.031.014.100
7 [NETWORK] All
CARD 1 MSK 255.255.000.000
GTW 000.000.000.000
IP 172.031.0.14.101
CARD 2 MSK 255.255.000.000
GTW 000.000.000.000
1 BACK
2 DEMO ECHO OFF/EG/SPU/PC
8 [OTHER] 3 EAV W/O GYRO OFF/ON All
4 ARP SELECT ARPA/ATA
5 INS OFF/SERIAL/LAN
3-37
3.3 Main Menu Tree
3. Factory menu
To access the Factory Menu, press the [2], [3] and [4] keys in sequence while pressing the
[1: HL OFF] key.
3-38
Chapter 4. System Setting
4.2 Overview of [FACTORY] menu
When you change the setting of a menu or on-screen icon menu, wait for six
seconds or more before tuning off the power. If the power is turned off in less
than six seconds, the data is not saved in the flash memory. After changing the
INSTALLATION and FACTORYmenu, restart the power.
Operation
Item
RCU-014 RCU-015, 016
Place the cursor on STBY-TX and
Press the [ENTER] key 5
Cancel the 3 minutes delay click the right button of the track
times while holding down the
function Note ball 5 times while holding down
[1:HL OFF] key.
the [F1] key.
Place the cursor on the menu and
INITIALIZE menu Press the [MENU] key 5
click the right button of the
(Call up the INITIALIZE times while holding down the
trackball 5 times while holding
menu) [1:HL OFF] key.
down the [F1] key.
Press the [2], [3] and [4] keys
FACTORY menu Press the [F2], [F3] and [F4] keys
in order while holding down
(Call up the FACTORY menu) while holding down the [F1] key.
the [1:HL OFF] key.
The brilliance is set to 50 when
Monitor brilliance Adjust of [BRILL] VR one key of [F1] to [F4] keys is
pressed for longer than 4 seconds.
Note: When the INITIALIZE menu or FACTORY menu is called up, the menu is
retained until the power is turned off.
If the power is turned on immediately after the power off, 3 minutes delay
counting is abbreviated.
4-1
4.2 Overview of [FACTORY] Menu
Sub
Menu Sub Menu-1 Remarks
Menu-2
1 BACK
Switch the language display. (English/Japanese)
2 LANGUAGE E/J When changing the language display, turn off the
power once.
FACTORY Return all the settings to the factory default setting.
3 FACTORY
Select “FACTORY DEFAULT” and click the left
DEFAULT Note
button. Or clicking the [ENTER] key 5 times.
4 FACTORY
See page. 6-17.
TEST
Note:
Following wettings are retained even after “FACTORY DEFAULT” is executed.
3) [FACTORY] menu
[Menu] -> 2 [LANGUAGE]
4-2
4.3 Overview of [INITIALIZE] Menu
Refer
Menu Sub Menu-1 Sub Menu-2 Remarks
to
1 BACK
1BACK
The level of video signals inputted into the processor unit differ
depending on the antenna cable length. This function compensates
the signal loss by the antenna cable.
AUTO/MANUAL 30
2 CABLE ATT ADJ - AUTO: Adjustment is automatically made by calculation based P.4-13
(Auto/Manual: 0 - 73)
on the noise level.
- MANUAL: Make adjustment so as to present a slight amount of
noise by setting GAIN to 80 and STC/FTC to OFF.
This is a function for the alignment of heading line to correct the
000.0
3 HD ALIGN bearing error of a target and its echoes. Limit the bearting error to 0.2
(0-359.9)
degrees or less.
Makes adjustment of TX delay by the electrical circuit and antenna
2 [ECHO ADJ] cable. Adjust range of echo so that a straight target such as a pier is
1 presented as an straight picture on short range. Or makes adjustment
4 TIMING ADJ
(0-4095) so as to allow main bang of about 5 mm radius (20 inch monitor) or
7 mm (23 inch monitor) from the center on the 0.5 NM range when P.4-14
MBS (listed below) is set to “0”.
Makes adjustment suppression for the main bang. Makes adjustment
0
5 MBS so that “MBS (listed above)” disappears on the S1 range of 1.5 NM
(0-255)
or less. (40 dB attenuation)
Selects the antenna height from the sea level. This setting affects
5/7.5/10/15/20/25/ the MANUAL and the AUTO STC operating range.
6
30/35/40/45/ Note: P.4-15
DEFAULT ANT HIGHT
more 50m The value set in this menu box is set as a default for the setting of
[PICTURE] -> 9 -> 3:ANT HEIGHT.
Cont’d
4-3
4.3 Overview of [INITIALIZE] Menu
7 NEAR STC CRVE 2/2.5/3/3.5 Fine adjustment of STC curve by range. The STC curve is primary
8 MID STC CRVE 3/4/5/6 determined by the ANT HEIGHT setting and secondary by the
P.4-15
setting of [PICTURE] ->9: CONDITION and [Menu] -> 0 -> 4 -> 6:
2 [ECHO ADJ] 9 FAR STC CRVE 6/7/8
MODEL.
1 Makes adjustment so that a ring-shaped picture outside the MBS
0 RING SUPPRESSION P.4-14
(0-255) range disappears. (20 dB attenuation)
1 BACK
START 000°
2 BLIND SECTOR 1 This is the only function to stop
ANGLE 000°
transmission in a specified bearing. Set
START 000° the bearing to suspend transmission.
When transmission is not suspended,
3 BLIND SECTOR 2 set the START and the ANGLE to 0
ANGLE 000°
degree.
4-4
4.3 Overview of [INITIALIZE] Menu
1 BACK
Sets whether to use the radar as a monitor (SUB) or not. When this is
P.4-20
2 RADAR MAIN/SUB set to SUB, transmission is disabled. Monitor signals are inputted
P.4-21
from the master radar to the terminal board J616: Master radar.
Sets measure of the Range ring
3 RANGE UNIT NM/SM/km/kyd
Note: IMO and A type not available
Sets the own radar: ANT number when it is connected with a
network. For viewing pictures from other antennas, you can switch
the display by selecting the [ANT INF] box (Inter-switch function).
Information on radars connected with the LAN can be checked on
4
the [ANT INF] box menu.
INSTALLATION P.4-19
4 RADAR NO 1/2/3/4/5/6/7/8 Note-1: Numbers are assigned as follows:
P.4-21
No. 1-4: With TR unit
No. 5-8: Without TR unit
Note-2: The radar IP address can be checked in “INITIALIZE Menu
-> 0 -> 7: NETWORK”. IP address is linked with the radar
number and automatically assigned.
FORE/MAINTOP/
Makes this setting for reference of the antenna location. This
MAIN2ND/
5 RADAR POSN information is shown on the [ANT INF] box menu.
MAIN 3RD AFT/
This setting is not used for signal processing.
PORT/STAR BOAD
Cont’d
4-5
4.3 Overview of [INITIALIZE] Menu
Cont’d
4-6
4.3 Overview of [INITIALIZE] Menu
BOW 0m
This setting is the data for indicating the radar antenna position in the
(0-999)
3 SCANNER POSN own ship mark. If you select ANT POSN in the [REF POINT] box,
PORT 0m
the radar antenna position becomes the reference point.
(99)
BOW 0m Sets the GPS antenna position. This data is used for calculating the
(0-999) cursor position (latitude, longitude).
4 GPS1 ANT POSN
PORT 0m The input ports of the GPS are:
(0-99) - GPS1: NAV port (J606)
BOW 0m - GPS2: LOG (J607), TRACK CONTROL (J620), HDG (J605),
5 (0-999) RS-232 (J601), LAN (INS)
5 GPS2 ANT POSN P.4-30
OWN SHIP PORT 0m The GPS1 or the GPS2 can be switched in “1. NAV AID” of the [OS
INFO (0-99) POSN] box menu.
BOW 0m Sets the conning position.
(0-999) This setting is used for indicating the conning position in the own
ship mark. If you select CONN POSN in the [REF POINT] box, the
conning position becomes the reference point of rangering,
6 CONNING POSN VRM/EBL markers and cursor. But the picture position is not
PORT 0m
changed.
(0-99)
Selecting the CONN POSN as REF POINT, the range and bearing of
the target on the radar display and the target viewed from the
conning position coincide with each other.
4-7
4.3 Overview of [INITIALIZE] Menu
Refer
Menu Sub Menu-1 Sub Menu-2 Sub Menu-3 Remarks
to
1BACK
This is the setting for outputting the tracking
data of the ARPA.
2 TTM OUTPUT OFF/REL/TRUE
Note: Specify the output port by “[Menu]
-> 0 -> 8 -> 5: INS”.
Sets the maximum acquisition range of the
3 MAX RANGE 24/32
ARPA.
No need for changing this setting.
16 There are 32 gradations for received echo
4 ECHO LEVEL
(0-31) levels. Set the threshold of the echo level to be
processed as ARPA.
Displays the echo processed by the ARPA
5 QV DISPLAY OFF/ON
echo.
Not displayed on the IMO type radar.
6 ARP PRESET As a general rule, the ARPA function does not
P.4-31
work without HDG data. This setting allows
6 ARP W/O GYRO OFF/ON
the ARPA to work without HDG, data and is
intended for use in installation on a fixed
position.
1 BACK
No need for changing this setting.
800M This is the setting of the target size. Targets
2 LAND SIZE
(100-1000) smaller than this setting are processed as the
ARPA target.
7 [ACQ PRESET]
XN12AF/XN20AF/
Since the horizontal beam width differs
XN24AF/XN4A/
depending on the antenna, the installed
3 ANT SELECT XN5A/SN30AF/
antenna type is selected so as to have the
SN36AF/SN4A/
appropriate ARPA echo.
SN5A
Cont’d
4-8
4.3 Overview of [INITIALIZE] Menu
Cont’d
4-9
4.3 Overview of [INITIALIZE] Menu
1 BACK
DRIFT=OFF
CPU
COUNTER=xxxxx
CPU STATUS=xxxxx
AUTO= x
Displays the ARPA status.
MAN= x
LOST= x
SCAN= xxxx
MIN HIT= x
E LEVEL= x
9 [ARP SENSOR DATA]
0 NEXT
6 ARP PRESET P.4-31
1 BACK
1= x
2= x
No need for changing the setting. Displays the
3= x
ARPA data for manufactural engineers. Select
-------
the data to be displayed in the “2. DATA NO”
30= x
listed below.
31= x
32= x
Allows the selection of data. The selected data
2 DATA NO
is displayed in the box shown above.
Returns the [ARPA PRESET] setting data to a
0 DEFAULT
default by clicking the left button 3 times.
4-10
4.3 Overview of [INITIALIZE] Menu
Refer
Menu Sub Menu-1 Sub Menu-2 Remarks
to
1 BACK
You can check the IP address to use when the radar is connected
with LAN.
IP
Note: Set the radar number in “[Menu] -> 0 -> 4 -> 4: RADAR
172.031.003.0xx
NO”. The IP address is automatically assigned by the radar
MSK
RADAR number.
255.255.000.000
No.1: 172.031.003.006 --- No.8: 172.031.003.013
GTW
000.000.000.000
Remark:
IP, MSK, GTW addresses can be changed.
7 NETWORK IP
172.031.014.100 P.4-34
MSK
CARD 1 You can check the IP address of CU-200 connected with the radar or
255.255.000.000
the LAN.
GTW
When two CU-200 are connected via the LAN, set the DIP switch in
000.000.000.000
CU-200.
IP
172.031.014.101
Remark:
MSK
CARD 2 IP, MSK, GTW addresses can be changed.
255.255.000.000
GTW
000.000.000.000
1 BACK
Allows selecting demo echoes.
- EG: EG-3000/2000 - SPU: Future development
8 OTHER 2 DEMO ECHO OFF/EG/SPU/PC
- PC: Demo picture of the PC (Application should have been
installed on your PC.)
Set whether to activate the EAV function without HDG data or not.
3 EAV W/O GYRO OFF/ON
It is intended for use in installation on a fixed position.
Cont’d
4-11
4.3 Overview of [INITIALIZE] Menu
The indication in [ARAP] and [ATA] box on the lower right display
4 ARP SELECT ARPA/ATA changes according to the setting. The trial maneuver function is not
available on the ATA.
Selects TTM output port.
OFF: Jxxx [ECDIS]
SERIAL: Jxxx [TRACK CONTROL]
LAN: Jxxx [NETWORK] This port is two way communication.
8 OTHER
Note:
5 INS OFF/SERIAL/LAN - Set “[Menu] -> 0 -> 6 -> 2.TTM OUTPUT” to “REL” or P.4-38
“TRUE”. The TTM is outputted.
- When this is set to OFF, “[Menu] -> 2 -> 7: [BARGE MARK]”
menu is displayed to allow the setting of BARGE MARK.
- When this is set to the SERIAL or the LAN, “[Menu] -> 2 -> 7:
[INS MARK]” menu is displayed to allow the ON/OFF setting
of the mark display from INS.
4-12
4.4 Initialize Setting
The level of video signals inputted into the processor unit differ depending on the
antenna cable length. To adjust the loss correction for it, two types of adjustment
methods are available (AUTO or MANUAL). You can use the both of them. After the
AUTO adjustment, you can make a correction by the MANUAL adjustment.
The adjusted data is saved on the SPU board. Based on this data, “CABLE ATT ADJ” is
executed on the IF board of the TR unit.
When AUTO is executed, a message “CABLE ATT ADJ” is displayed. It takes about 5
minutes to complete the adjustment. Proper noise levels are automatically adjusted and
the adjusted data is saved on the SPU board.
XXX data=X
Step= 1 (-> 2)
att data=XX
LEVEL AVERAGE=XXX
In the MANUAL adjustment, set the 24 NM range, the long pulse, Gain to “80”, STC to
“0”, FTC/EAV/ES/ to OFF and IR to “2”, and then make adjustment so as that the grass
noise slightly appears.
4-13
4.4 Initialize Setting
Photo 4.4.5 Timing has not been adjusted Photo 4.4.6 Picture is absorbed due to too
much timing adjustment
Photo 4.4.7 Proper timing adjustment, the Photo 4.4.8 The main bang disappears
main bang appears near the because of too much MBS adjustment.
center Adjust MBS so that a slight amount of
main bang appear. When ring-shaped
echoes appear outside the main bang,
make adjustments in RING
4-14 SUPPRESSION.
4.4 Initialize Setting
Set the antenna height for the setting of DEFAULT ANT HIEGHT, by “[PICTURE] ->
9 -> 3: ANT HIEGHT”. The STC curve is primary set by ANT HIEGHT.
By adjusting the [A/C SEA] knob, the STC curve moves up and down. The ANT
HIEGHT, SEA CONDITION and pulse length determine turning points of the curve.
And the setting of the STC RANGE changes the turning points of MID STC and FAR
STC. The higher is the antenna and the worse is the sea condition, the more the control
distance of (1<5) STC is extended.
For instance, if the antenna height is 30 m for the X-band radar, the NEAR turning point
is 4 to 5 NM and the MID turning point is 19 to 20 NM. In AUTO STC, the optimum
STC curve and movement of STC curve (upward and downward) are automatically
controlled according to a reception signal level and Range.
4-15
4.4 Initialize Setting
The photos shown below are given as examples for comparison of pictures when the
setting of the SEA CONDITION and the ANT HIEGHT are changed in FAR-2837S.
These are pictures when the range is set to 24 NM, and also AUTO STC, IR, ES and
EAV AUTO RAIN were set to OFF.
When SEA CONDITION is set to 4: bad sea condition, the effect of the STC becomes
greater.
When the antenna height is set higher, the control range of the STC becomes longer.
Note:
You can store the setting according to the sea condition in the [PICTURE] box menu
and assign it to fucntion keys in the [MENU] -> 9 -> 3, 4, 5 and 6.
4-16
4.4 Initialize Setting
1. In case that the antenna motor power is the DC type (RSB-097: FAR-2xx7)
ANT ON, ANT SPEED (H/L level), and B.P signals from the SPU board are
inputted to the PWR board, and the antenna rotation speed is kept constant.
See page.7-67.
ANT Motor
+24VDC 42rpm
MAIN CPU
ANT ON J610
BP ANT SPEED ANT +20VDC 36rpm
REG
Control (ANT Motor)
BP
U21
SPU-013 PWR
RPU-013
BP ANT SPEED
24 rpm: 144 Hz HI: 42 rpm
36 rpm: 216 Hz Low: 36 rpm
42 rpm: 252 Hz
4-17
4.4 Initialize Setting
ANT Motor
AC in AC power
RL
PSU-007
RPU-013 J604
+12V
MAIN CPU
ANT ON Q5
2SC3265Y
U21
SPU-013 Termional
RSB-014
RSB-015
ANT MOTOR
ANT ON
RL RFC p.c.b
ANT Power (AC)
RTR-082
RPU-013
4-18
4.4 Initialize Setting
Important:
To make the unit work as a radar, set the radar number to 1 to 4.
RADAR No. 1 to 4: With ANT unit
RADAR No. 1: 172.031.003.006
RADAR No. 2: 172.031.003.007
RADAR No. 3: 172.031.003.008
RADAR No. 4: 172.031.003.009
To make the unit work only as a monitor of the inter-switch, set the radar number 5 to 8.
RADAR No. 5 to 8: Without ANT unit
RADAR No. 5: 172.031.003.010
RADAR No. 6: 172.031.003.011
RADAR No. 7: 172.031.003.012
RADAR No. 8: 172.031.003.013
Note!!
When changing the IP address (RADAR NO.) of the radar connected with the
LAN, be sure to restart the power for other radars, HUB-100 and CU-200
connected to the LAN.
4-19
4.4 Initialize Setting
4.4.6 RADAR
INITIALIZE -> 4: INSTALLATION -> 2
This is the setting for using this unit as, a sub monitor by signals from the master radar
(external input of analog video).
See page.4-23 for major items that are operable in SUB mode.
Note:
When you turn on the power and switch the setting to SUB (Monitor) in the [ANT-X]
box, the standby display appears correctly to allow you to monitor pictures. When
you switch the unit to the own radar, 3 minute counting starts.
4-20
4.4 Initialize Setting
4.4.7 Inter-switch
To view pictures of other radars of FAR-2xx7 series connected to the LAN, switch the
radar No. (ANT NO.) to the number of the radar that you desire to view. On the
switched picture, you can perform operations such as STC, and Range change. For these
inter switch functions, the IP address linked with the set radar number is used. See
p.4-19 for the setting of the radar number. Basically, it uses that the transfer of pictures
are UDP, and then commands such as key operation are TCP.
To check the information of the radar antenna connected to the LAN, open the [ANT-X]
box menu. You can check BAND, MODEL and POS information of radars (1 to 4)
connected to the LAN.
Operatable Operatable
No.1 Radar: No.2 Radar: No.3 Radar:
Priority ON Inoperatable Priority OFF Inoperatable Priority OFF
Video signal processing such as Echo Stretch, Echo Average and Echo Trail can be
controlled on a processor unit that in side of the received video signals.
Signal processing such as the ARPA acquisition and tracking is performed on its own,
and output this on the network. In the ARPA, you can set the vector mode/time, track
interval, and TCPA/CPA on the switched side.
See the next page for operations among these radars.
4-21
4.4 Initialize Setting
4-22
4.4 Initialize Setting
FAR-2xx7 set
LAN connection
Main function as sub monitor
(Inter switch function)
(SUB function)
PULSE LENGTH Linked
RANGE Linked Enabled
A/C SEA Linked
GAIN Linked
A/C RAIN Linked Enabled
PICTURE Linked Enabled
TX/STBY Linked
ARPA ACQ Linked
TARGET CANCEL Linked
[ARPA]->1: ARPA SELECT Linked
[Menu]->0->6->7->3:ANT SELECT Linked
LOST ACK Linked
ARPA vector Linked
ARPA CPA/TCPA Linked
TUNE MANUAL Linked
TUNE AUTO Linked
[Menu]->0->3->2, 3:BLIND SECTOR Linked
[Menu]->0->4->5: RADAR POSN Linked Enabled
[ARPA]->2: ALL CANCEL Linked
REF POINT Linked
Image processing etc.
Individual operation Enabled
・ES ・EAV ・Echo trail ・Wipper
IR, Auto RAIN Linked
Zoom Individual operation Enabled
Vector time/Vector mode Individual operation
ARPA/AIS plot interval Individual operation
Receives data from the
ARPA acquisition and tracking
other dispaly
Displays data of the other
Guard zone
dispaly
Alarm zone Individual operation Enabled
Displays data of the other
HDG data Displays own data
dispaly
NAV data other than HDG data Displays own data Displays own data
[Menu]->3: TUNE INITIALIZE Own radar only
PM, SART Own radar only
OFF SET, HD OFF Individual operation Enabled
EBL, VRM Individual operation Enabled
IL Individual operation Enabled
Switch display mode and presentation mode Individual operation Enabled
Mark、BRILL operation Individual operation Enabled
4-23
4.4 Initialize Setting
4.4.8 MODEL
INITIALIZE -> 4: INSTALLATION -> 6
Functions change according to the setting of MODEL.
“A, B and C” in the table below represent parameters. For instance, the models
specified as “A” in the column of the STC curve use the same parameters.
Main function
Transmission ANT ON
MODEL setting Transmission
STC pulse B.P output control
repetition
curve waveform calculation signal form
frequency
control RFC board
6 6kW X-band A A A NO A
FAR-2x17
12 A B A NO A
FAR-2x17BB
FAR-2x27
25UP A C A NO A
FAR-2127BB
25
FAR-2817W A D A NO A
DOWN
50 50kW X-band A E A NO B
FAR-2137S
30UP B F B NO A
FAR-2837S
30
FAR-2837SW B G B YES A
DOWN
60 60kW S-band B H B NO B
Note:
B.P output calculation
B.P inputted from the antenna is 256 pulse /rev. in the S-band radar and 360 pulse
/rev. in the X-band radar. This is automatically recognized by MODEL setting. The
B.P output at Slave port is 360 pulse /rev. on both S and X band radar.
4-24
4.4 Initialize Setting
Type
Differences in Main Menus
IMO A B C
Menu – 1:MARK – 7:ECHO AREA
NO NO YES YES
(ECHO AREA can be selected from CIRCLE/WIDE/ALL.)
Menu – 2:MARK – 9:EBL CURSOR
(Only when NM is selected for the unit of the range, switching between YES YES NO NO
REL and TRUE is enabled.)
Menu – 2:MARK – 9: [EBL,VRM, CURSOR SET]
(Selection of the unit of the range from NM/SM/km and kyd. And also, NO NO YES YES
switching between REL and TRUE.)
Menu – 3:ALARM – 6: [ALARM OUT1], 7, 8, 9 –> 9:ALARM OUT
POLARITY NO NO YES YES
(Setting of alarm output polarity)
Menu – 4:ARP/AIS – 5: ARP SYMBOL – 2: ARP SYMBOL COLOR ->
RED NO YES YES YES
(Restriction on ARP symbol color)
Menu – 4:ARP/AIS – 6: AIS SYMBOL – 2: AIS SYMBOL COLOR -> RED
NO YES YES YES
(Restriction on AIS symbol color)
Menu – 5: PLOTTER – 2: CHART COLOR
NO YES YES YES
(Setting of CHART COLOR)
Menu – 5: PLOTTER – 5: TGT TRACK INTERVAL NO YES YES YES
Menu – 5: PLOTTER – 6: TGT TRACK COLOR
NO YES YES YES
(Selection of track color of other ship)
Menu – 5: PLOTTER – 8:[DATA ERASE] – 3:TARGET TRACK
NO YES YES YES
(Erasing of track of other ship)
Menu – 5: PLOTTER – 9: DISPLAY – 2:GRID – OFF/ON
YES YES YES NO
(To display grid or not)
Menu – 5: PLOTTER – 9: DISPLAY – 2:GRID – OFF/L/L/GYOKU
NO NO NO YES
(ON/OFF of GYOKU ”Fishing area” display)
Menu – 5: PLOTTER – 9: DISPLAY – 4: TARGET TRACK
NO YES YES YES
(To display of track of other ship or not)
Menu – 5: PLOTTER – 9: DISPLAY – 6: LAND DENSITY
NO YES YES YES
(To display the land density or not)
Menu – 5: PLOTTER – 9: DISPLAY – 7: PLACE NAME
NO YES YES YES
(To display the place name or not)
4-25
4.4 Initialize Setting
Type
Differences in Main Menus
IMO A B C
Menu – 6: CARD – 7: [WR TARGET TRACK]
NO YES YES YES
(To write the track of other ship or not)
Menu – 8:NAV LINE WPT – 2:NAV LINE DATA – WPT MARK NO YES YES YES
Menu – 9: CUSTOMIZE/TEST – 3: [F1], 4, 5, 6 – 5: [OPERATION] – 2 ->
NO NO NO YES
TLL (Presence or absence of TLL output)
Menu – 9: CUSTOMIZE/TEST – 7: [OPERATION] – 5: POP UP
GUIDANCE NO NO YES YES
(ON/OFF settting of pop up guidance)
Menu – 0:INITIALIZE– 4:INSTALLATION – 3:RANGE UNIT
NO NO YES YES
(Set measure the Range ring)
Menu – 0:INITIALIZE– 6:ARP PRESET – 6:ARP W/O GYRO
NO YES YES YES
(ARPA operation setting without GYRO data)
Table 4.4.5(2/2) Functions for Radar Type (Differences On-Screen Box Menus)
Type
Differences in Icon Menus
IMO A B C
[OS POSN] – 1:NAV AID – DEAD RECKONING
(On the IMO type, manual input is disabled when ON is set in NO YES YES YES
“[Menu]->4->8:AIS FUNCTION”)
[SPD] – 1:SHIP SPEED – MANUAL/REF
(On the IMO type, MANUAL/REF cannot be switched when ON is set in NO YES YES YES
“[Menu]->4->8:AIS FUNCTION”)
[SPD] – 1:SET DRIFT – OFF/ON
(On the IMO type, SET DRIFT is disabled when ON is set in NO YES YES YES
“[Menu]->4->8:AIS FUNCTION”)
[BRILL] (1/2 page) - 1: ECHO COLOR ! COLOR
NO NO YES YES
(On the IMO type, ECHO COLOR COLOR is unable.)
[BRILL] (2/2 page) - 0: NEXT! 0: CHART NO YES YES YES
[TRAIL] - 3: NARROW TRAIL
NO NO YES YES
(Setting of narrow trail)
[MARK] -0: MAP MARK COLOR
NO YES YES YES
(Specification of chart color. CHART is disabled on the IMO type.)
[ANT INF] – 8: SUB MONITOR
NO NO YES YES
(Easy ON/OFF switching between radar and sub monitor)
[COURSOL] – TARGET TRACK ON, TARGET TRACK OFF
NO YES YES YES
(ON/OFF setting of TARGET TRACK is not displayed on the IMO type)
4-26
4.4 Initialize Setting
4-27
4.4 Initialize Setting
2. Adjust [GAIN] VR so as to allow a small amount of noise. The gain at that time is
approximately “70”.
3. Adjust the PM gain by rotaging the wheel of the track ball so as to allow a slight
amount of the second ring. Numerical input (0 to 255) from the keyboard can also be
accepted for the PM GAIN. “255” is the maximum attenuation level (i.e. lowest
video input levels.)
10dB
Noise Level
First ring
No.1 Ring Echo No.2 Ring Echo
4-28
4.4 Initialize Setting
Note:
Why the second ring should be pale?
In the PM unit, the diference in gain between the 1st and 2nd rings is set to 10 dB.
Being pale the 2nd ring and making it the same level as the noise level means that the
1st ring echo is adjusted 10 dB higher than the noise level. If the 1st ring disappears, it
is known that the transmit, receive or transmit/receive gain is reduced by 10 dB. For
this reason, you can find the radar sensitivity from the status of the ring echoes.
Previous PM echo
For exmple, the figure below show the FAR-2805 PM picture, which allows
individual determination of degradation in reception and transmission performance
based on the PM echo.
The 1st ring echo is set to 12 NM and shows the degradation of reception and
transmission output according to its distance. Output is degraded by -3 dB/3 NM. The
interval between ring echoes is 3 dB. If the 4th ring disappears, for instance, you can
find that receive sentences have reduced to 3 dB.
12NM
0dB
-3dB
-6dB
-9dB
4-29
4.4 Initialize Setting
“3: SCANNER POSN” and “6: CONNING POSN” data determine the origin of a radar
graphic data. The figures below show the origin of range ring by the selection of [REF
POINT]. The graphic data, VRM, EBL, ARPA target, cursor and positioning of AIS
target mark are caluculated from the [REF POINT]. Selecting the “CONN POSN”,
those data coincides with the crew’s eye even if the scanner position is away from the
conning position.
“4, 5: GPS ANT POSN” data is used for L/L calculation of the cursor position on the
screen. The displayed position data in the [OS POSN] is the GPS antenna position.
Note:
“[INSTALLATION] -> 5: RADAR POSN” data is used for video signal processing of
echo trails and echo averages.
4-30
4.4 Initialize Setting
- [J619]: ECDIS
- [J620]: TRACK CONTROL
- [NETWORK]: LAN
See page. 4-38 for details.
4-31
4.4 Initialize Setting
Displayed data
Radar video signal
Echo Momentum
echo Interface
Detection estimate Monitor
ANT rotation signal sorting unit
unit unit
LOG/GYRO/GPS
4-32
4.4 Initialize Setting
4-33
4.4 Initialize Setting
4.4.13 NETWORK
INITIALIZE -> 7
1. Checking of IP address
IP address when connected with the LAN can be checked in this menu. The radar IP
address is automatically assigned by setting the radar number in [Menu] -> 0 -> 4 -> 4:
RADAR NO.
Drive assignment
CU-200 IP adress Subnet mask Default gateway [MENU]->[6 CARD]->
2. DRIVE SELECT
CARD 1 172.031.014.100 A (Left slot) / B (Right slot)
255.255.000.000 000.000.000.000
CARD 2 172.031.014.101 C (Left slot) / D (Right slot)
4-34
4.4 Initialize Setting
2. Changing of IP address
Never change the IP address except for special types specified below.
If the IP address is improperly changed, the system may fail to work properly.
In order to allow the Inter switch function of the radar to work properly between
networks, it is required to set up the IP address specified to the network, subnet mask,
default gateway and destination. Connection should be one-to-one connection according
to the 100 Base-Tx. Detailed equipment and specifications are not described here.
The IP address can also be changed on CU-200. (Only one network.) It cannot be shared
among multiple networks.
Note that IP address of CU-200 can be rewrite, and the program versions of CU-200 are
0359209-01.02 or later.
FAR-2xx7 FAR-2xx7
Router
Series Series Note:
The DESTINATION setting
Gateway: Gateway: has to set the IP address of
172.31.3.254 192.168.1.254
the other radar.
RADAR NO.(ANT) :1 RADAR NO.(ANT) :2
IP ADDRESS :172.31.3.6 IP ADDRESS :192.168.1.1
SUBNET MASK :255.255.0.0 SUBNET MASK :255.255.0.0
GATEWAY :172.31.3.254 GATEWAY :192.168.1.254
DESTINATION :192.168.1.1 DESTINATION :172.31.3.6
Procedure
1. Press the [Menu] key 5 times while holding down the [1] key to open the
“INITIALIZE” menu.
2. Select the radar number of the own radar in “INITIALIZE -> 4: INSTALLATION
-> 4: RADAR NO”.
3. When the message “Completed!! Power on restart.” is displayed, restart the power.
4. Press the [2], [3] and [4] keys in order while holding down the [1] key to call up the
“FACTORY” menu.
5. Press the [ENT] key 5 times while holding down the [1] key to call up the
“INITIALIZE” menu.
4-35
4.4 Initialize Setting
Open “INITIALIZE -> 7: NETWORK” menu. You can find “2 [NETWORK SETTIG]”
menu added to the “NETWORK” menu.
6. When you open the “2 [NETWORK SETTIG]” menu, the “1 [RADAR]”, “2
[CARD 1]” and “3 [CARD 2]” menus are displayed.
7. Select “1 [RADAR]” and set the data of the IP address and Subnet mask.
8. When the setting is complete, select “YES” in “6 WRITE SETTING” and click the
left button. When “YES” is selected, the YES. is shown in the box.
9. When the message “Completed!! Power on restart.” Is displayed, restart the power.
10. Call up the “INITIALIZE” menu again and make sure that the address has been
changed in “8 NETWORK”.
2. Select “INITIALIZE -> 4: INSTALLATION -> 4: RADAR NO” and click the left
button.
3. When the message “Completed!! Power on restart.” is displayed, restart the power.
4. Call up the “INITIALIZE” menu again and make sure that the IP address has been
reset to the default in “8 NETWORK”.
4-36
4.4 Initialize Setting
Procedure
1. Follow the same steps 4 to 7 as for the procedure for changing the radar IP address.
2. Select [CARD x] to be changed and set the data of the IP address and Subnet mask.
3. When the setting is complete, select “YES” in “6 WRITE SETTING” and click the
left button. When “YES” is selected, the YES. is shown in the box.
4. When the “YES” display returns to the normal display, restart the power.
5. Call up the “INITIALIZE” menu again and make sure that the IP address has been
changed in “8 NETWORK”.
Note:
Even if the IP address is changed, allocation of the drive is specified A/B for
CARD-1 and C/D for CARD-2.
Note
After the IP address of CU-200 connected with the LAN is changed, be sure to
restart the power for other radars and HUB-100 connected with the LAN.
4-37
4.4 Initialize Setting
4.4.14 INS
INITIALIZE -> 8: OTHER -> 5
This is for the selection of the port of the INS (Integrated Navigational System).
Set [Menu] -> 0 ->6 -> 2:TTM OUTPUT to “REL” or “TRUE”.
* ECDIS-related sentence
ECDIS-related input sentence (INS)
GLL, GGA, FUGLL, DTMOSD, ZDA, DPT, MWV, PAESP, PAESC, PAESF,
PLSPL, PLSPS, PAESW, PAESN
Output sentence
OSD / PAESP / TTM* / PFEC, RAssd / RSD
* To output TTM data
Set [Menu] -> 0 ->6 -> 2:TTM OUTPUT to “REL” or “TRUE”.
Note:
By the above setting, the items of [Menu] -> 2 -> 7 are changed.
- TTM OUTPUT: REL or TRUE
[Menu] -> 2 -> 7: [INS MARK]
Make the setting of USER CHART, CURVED EBL, CHART SYMBOL,
NOTE BOOK and RUTE associated with INS.
- TTM OUTPUT: OFF
[Menu] -> 2 -> 7: [BARGE MARK]
Make the setting of ON/OFF, BARGE MARK SIZE and ARANGEMENT for
the display of BARGE MARK.
4-38
4.5 Jumper Setting of Terminal Board
TERMINAL p.c.b
Set position
GND2
Floating
common
2 3 11 14
ST1 ST2 AIS port: [J655]
GND2 Vcc2
1 Vcc 420kHz HDG port: [J656]
A RDx-B
16
RD RO 3
28 R 330 x 3
B
1 2 RDx-A
AIS/HDG sensor
RE 15
27
RO2
17
(100Ω)
IEC-61162-2
LTC1535
Y TDx-B
DE 13
26
TD DI D
TDx-A
25 Z 12
SLO COMMON
4 GND 18
GND
Logic common
4-39
4.5 Jumper Setting of Terminal Board
- AIS TD
- HDG SENSOR
Terminator Terminator
Not used Used
FAR FAR
4-40
4.6 Setting of Monitor Unit
SPU board
03P9337
Dip SW: S1
4-41
4.7 Setting of AD-100 or GC-10
RPU-013
or Terminal p.c.b
NMEA Ver-2.0
HDT/38.4kbps/25msec
J6(4p) J656(HEADING)
GC-10
4-42
4.7 Setting of AD-100 or GC-10
Note:
When the GC board of the Ver-05 is incorporated in RPU-013, and the power-off function is set to
“Enable” and when power-off is detected, all the output data are stopped. When this happens, set
the HDG value in the [HDG] box menu again.
4-43
4.7 Setting of AD-100 or GC-10
In the factory setting, all the DIP switches are set to OFF and jumpers are set to #1 except that JP1 is set
to #1, #2 and #3.
4-44
4.7 Setting of AD-100 or GC-10
SW 3
SW3-#1
NMEA Ver SW3-#1 OFF: Ver 1.5 / ON: Ver 2.0
(See Table 4.7.5)
SW3-#2 Baud rate SW3-#2 OFF: 4,800 bps / ON: 38,400 bps
Ver03, 04:
SW3-#3 SW3-#3 OFF: AG / ON: HE
Talker name
(Setting according
Ver05:
to the program) SW3-#3 OFF: Disable / ON: Enable
Power-off function
Jumper: JP1 – JP7
#1, #2, #3 AC synchrous
JP1 Gyro type #2, #3, #4 DC synchrous
#4, #5, #6 DC step
#2 20 VAC to 70 VAC, 20 VDC to 100VDC
JP2 Stator voltage
#1 40 VAC to 135 VAC
#2 20 VAC to 70 VAC
JP3 Rotor voltage
#1 40 VAC to 135 VAC
- JP4-#2, JP5-#2
JP4 20 VAC to 45 VAC, 20VDC to 60 VDC
Operating voltage
- JP4-#1, JP5-#1
JP5 30 VAC to 135 VAC, 40 VDC to 100 VDC
JP6 AD format data
25 ms or 200 ms
JP7 TX interval
Table 4.7.4 NMEA output Interval, Output Sentences and Baud rate
When 200 ms, 100 ms or 25 ms is selected for the output interval, the output sentence is HDT only.
When 25 ms is selected, the Baud rate is fixed at 38,400 bps.
4-45
4.7 Setting of AD-100 or GC-10
Fucntion setting
SW3 setting
NMEA version Baud rateNote-1 Talker name/Power-off function
OFF 1.5
SW3-#1
ON 2.0
OFF 4,800 bps
SW3-#2
ON 38,400 bps
AG (Heading/track
OFF
SW3-#3Note-2 Controller (autopilot) general)
ON HE (Heading sensor; gyro/north seeking)
OFF Disable
SW3-#3Note-3
ON Enable
Note-1 When the output interval is set to 25 ms (SW2-#5)and #6 are set to ON, the Baud rate is fixed at
38,400 bps.
Note-2 In the program Ver-03 and 04, the talker name is set here.
Note-3 In the program Ver-05, the power-off function is set and the talker name is fixed to HE.
4-46
4.7 Setting of AD-100 or GC-10
SW3:
JP4 Baud rate
Version
JP5 Ver03, 04: Talker name
Ver05: Power-off function
JP6, 7:
JP6 JP7 AD output interval
(25 ms/200 ms)
4-47
4.8 Add to the Memory Card I/F: CU-200
LAN
No.2 Note:
NETWORK
CU-200 When connecting RPU-013 and CU-200
RPU-013 HUB LAN
directly, Cross cables are used. When the
LAN No.1 HUB-100 is used for the connection,
(Straight cable)
CU-200
LAN either straight cable or cross cable can be
(Straight cable)
used. The HUB-100 automatically detects
LAN (Cross cable)
all the ports and cable types.
.Setting
1.
1. Turn the power off.
2. Set IP0 and INIT of DIP switch (S1) to ON.
3. Turn the power on and wait until CR2 starts to blink.
4. When CR2 starts to blink, turn the power off and return INIT of S1 to OFF.
5. IP address was changed from 172.031.014.100 to 172.031.014.101.
S1 (DIP SW)
#1: INIT #3: IP1 #2: P2 #4: IP0
NET-100 board
4-48
4.8 Add to the Memory Card I/F: CU-200
.Confirmation of IP address
2.
You can check the radar IP address, “Card 1 IP address” and “Card 2 IP address” on
“[MENU] -> 0 -> 7:NETWORK”.
“CARD x IP ADDRESS” appears when CU-200 is recognized.
Assignment of drive
CU-200 IP address
[MENU]->[6 CARD]->2. DRIVE SELECT
CARD 1 172.031.014.100 A (Left slot) / B (Right slot)
CARD 2 172.031.014.101 C (Left slot) / D (Right slot)
Note
After the IP address of CU-200 connected with the LAN is changed, be sure to
restart the power for other radars and HUB-100 connected with the LAN.
4-49
4.9 Selection of NAV DATA Input: [OS POSN]
Table 4.9.2 Priority of Other than POS, COG, SOG and DTM
Order of priority
TRACK
NAV LOG HEADING RS232C NETWORKNote NETWORKNote
CONTROL
(J606) (J607) (J605) (J601) (LAN INS) (LAN NAV)
(J620)
7 6 5 4 3 1 2
Note:
[NETWORK] port is assigned with the port number for the NAV data “10021”and the port
number for the INS data “10028”.
4-50
4.9 Selection of NAV DATA Input: [OS POSN]
Note:
The LAN port is assigned with port numbers “10021” for NAV data and “10028” for INS
data.
Table 4.9.3 Setting of [OS POSN] -> 3.SIO DATA LAN OUTPUT
4-51
4.9 Selection of NAV DATA Input: [OS POSN]
HDG data
xx.xx.xxx S
xxx.xx.xxx E NAV data
HUB
NAV data
NAV data NAV(L/L, SPD) data
NAV(L/L, SPD) data LAN
No.1 FAR- LAN No.2 FAR-
NAV data
NAV(L/L, SPD) data NAV data NAV(L/L, SPD) data
No.1 FAR- LAN LAN No.2 FAR- FAR
HDG data HDG data Input the HDG data for each
xx.xx.xxx S xx.xx.xxx S
xxx.xx.xxx E xxx.xx.xxx E radar.
INS Port No.10028
NMEA Port No. 10021
4-52
4.9 Selection of NAV DATA Input: [OS POSN]
The setting of TTM OUTPUT and INS shown in the Table below is for running TTM
data over the LAN. It is not the setting for sharing NAV data.
Note:
When inputting the POS data from INS to radars, set NAV AID setting to the GPS2 in the
respective radars.
3. Sharing NAV data with No.x radar from INS and with No.2 radar from No.1 radar
This setting assumes that NAV data is outputted from INS through the LAN port.
ECDIS
HUB
4-53
4.9 Selection of NAV DATA Input: [OS POSN]
The setting of TTM OUTPUT and INS shown in the Table below is for running TTM data
over the LAN. It is not the setting for sharing NAV data
4-54
4.10 Setting of RGB BUFF Board: 03P9229B
RPU-013
J3(DVI) DVI
VR-5000
Function Jumper Setting Factory setting
connection setting
H SYNC A-Comm. Reverse
J4 B-Comm.(Center) B-Comm.
polarity setting B-Comm. Retain
V SYNC A-Comm. Reverse
J5 B-Comm. (Center) B-Comm.
polarity setting B-Comm. Retain
Input voltage A - 5 V input B
J6 B
selection setting B - 12 V input (“-5V” is not used.)
Note: Comm: Jumper center
4-55
4.10 Setting of RGB BUFF Board: 03P9229B
03P9229
Board 03P9229A 03P9229B
(FR-1500III,
Parts (FR-2xx5) (FAR-2xx7)
FR-1700)
R9 560 ohm 560 ohm 390 ohm
R10 560 330 390
R12 560 560 390
R13 560 330 390
R15 560 560 390
R16 560 330 390
R20 Not required 75 75
R21 Not required 75 75
R22 Not required 75 75
Label print None A B
1.3
0V Note:
Each signal is measured under unloaded
condition.
4.5 4.5
0V 0V
17 ms 15 us
RGB BUFF board RGB BUFF board
[J5]-B to “Retain”. [J4]-B to “Retain”.
Fig. 4.10.4 V-SYNC Signal Waveform Fig. 4.10.5 H-SYNC Signal Waveform
4-56
4.10 Setting of RGB BUFF Board: 03P9229B
Item Setting
Channel # VD 1 VD 1 VD 1 VD 1
Channel ID FAR-28x7 FAR-21x7 FR-2105 FR2805
(Input the model name) (Input the model name) (Input the model name) (Input the model name)
Source NO.x RADAR NO.x RADAR NO.x RADAR NO.x RADAR
(Input the radar No.) (Input the radar No.) (Input the radar No.) (Input the radar No.)
Source type 1 1 1 1
Horizontal offsetNote-1 127 167 175 245
Vertical offset 37 37 40 17
Pll multiplier 847 847 847 1375
Horizontal sync
Negative Negative Positive Negative
polarityNote-2
Phase 192 192 192 48
Horizontal resolution 1280 1280 1280 1066
Vertical resolution 1024 1024 1024 800
VCO range 48 48 48 44
Save image to web Saved as JPEG Saved as JPEG Saved as JPEG Saved as JPEG
Debug level None None None None
15-bit 15-bit 15-bit
Color mask bit 6 - bit
(11111000 x 3) (11111000 x 3) (11111000 x 3)
Sample rate 15 Secs Fixed 15 Secs Fixed 15 Secs Fixed 15 Secs Fixed
Interlace type Alternate pixel Alternate pixel Alternate pixel Interlaced
Sync type Separate SYNC Separate SYNC Separate SYNC Separate SYNC
Radar model 1 – FR2115 1 – FR2115 1 – FR2115 0-User defined
Contrast/GAIN Red 128 128 128 100
Contrast/GAIN Green 128 128 128 100
Contrast/GAIN Blue 128 128 128 100
Brilliance/OFFSET
128 128 128 100
Red
Brilliance/OFFSET
128 128 128 100
Green
Brilliance/OFFSET
128 128 128 100
Blue
4-57
4.11 Alarm Output Setting
1. RCU-014
Table 4.11.1 Setting of RCU-014:S36
Factory
S36 Function Setting
setting
SYSTEM FAIL ALARM
When RPU-013 and RCU-014 cannot ON Output
communicate with each other due to a
1 ON
problem on RPU-013, set whether to
output SYSTEM FAIL alarm signal from OFF Do not output
RPU-014 or not
Normally Close
ON In the event of alarm,
RELAY STATUS
relay is set to Open.
2 Setting of polarity of the alarm signal ON
Normally Open
(relay output).
OFF In the event of alarm,
relay is set to Close.
3 Unassigned OFF OFF
4 Unassigned OFF OFF
4-58
4.11 Alarm Output Setting
Factory
S6 Function Setting
Setting
SYSTEM FAIL ALARM ON Output
1 ON
The same as described for RCU-014 OFF Do not output
RELAY STATUS ON Normally Close
2 ON
The same as as described for RCU-014 OFF Normally Open
S6 (DIP SW)
Note:
When the communication with processor unit is disabled due to the problem on the control
unit side, “KEY” alarm is displayed in the ALARM box and the control unit gives beeping
sounds. The control unit does not output SYSTEM FAIL ALARM.
4-59
4.11 Alarm Output Setting
ALARM SYSTEM
BZ ON BZ OFF
[ALARM ACK] ON
BZ ON BZ OFF
BZ ON BZ OFF
[ALARM ACK] ON
BZ ON BZ OFF
4-60
4.11 Alarm Output Setting
RPU-013
SPU p.c.b
Terminal p.c.b
U31 EXT ALARM ACK N
I/F
MAIN CPU
4 ALARM1-0
Normal close 1
U21
3 ALARM1-1
Q4 2
U22 U12
I/F (PS7241 1B)
ALARM2-0
Same as
above ALARM2-1
(U11/Q3)
ALARM3-0
Same as KEY
above ALARM3-1
(U10/Q2) J602
SYS FAIL H
ALARM4-0 9
Normal open 1 4 SYS FAIL C
ALARM4-1 10
Q1
2 3
U9
(TLP176G TP)
SYS ACK H J622
1
ALARM 4
ALARM 3
ALARM 2
ALARM 1
GND
2
KEY
8 7 6 5 4 3 2 1 9 12 11
J612
EXT ALARM
ALARM SYSTEM
ALARM SYSTEM
RPU-013
400V max.
100mA max.
1
4-61
4.11 Alarm Output Setting
4-62
4.11 Alarm Output Setting
Output of ALM-1, 2, 3
ALARM OUT POLARITY --> NORMAL
Power ON ALARM Occur ALARM resolved Power OFF
Closs
Delay
Power OFF Initializing
Open
BZ ON BZ OFF
[ALARM ACK] ON
ALARM OUT POLARITY --> INVERT
BZ ON BZ OFF
Power ON ALARM Occur ALARM resolved Power OFF
Closs
Delay
Power OFF Initializing
Open
BZ ON BZ OFF
[ALARM ACK] ON
BZ ON BZ OFF
BZ ON BZ OFF
[ALARM ACK] ON
BZ ON BZ OFF
BZ ON BZ OFF
[ALARM ACK] ON
BZ ON BZ OFF
5sec
5sec
5sec
4-63
4.12 Change of Power Input Type
F1
- 100 VAC: 10 A (125 V)
PWR board
- 220 VAC: 5 A (250 V)
- 24 VDC: 20 A (125 V)
FIL board
J108
220 VAC: Open
100 VAC: Jumper between 1-2, 4-7, 5-8
CR23:INPUT ERROR
4-64
4.12 Change of Power Input Type
Adjustment method
Overvoltage
Type Setting of J108 Setting of input power
protection Factory setting
voltage
adjustment
03P9339C, D
Open 288 VAC 282 to 294 VAC
(220 VAC) Point at which CR23
For is turned on by
03P9339A, B adjusting R21
1-2, 4-7, 5-8 144 VAC 141 to 147 VAC
(100 VAC)
Jumper
Note:
When the setting of “J108” is just changed without adjustments as menteioned above,
the operating voltage of the overvoltage protection circuit does not meet the specified
value.
- 220 VAC -> 100 VAC: approximately 130 VAC.
- 100 VAC -> 220 VAC: approximately 325 VAC.
Operation without re-adjustments may result in a failure of the equipment.
2. Circuit setting
The setting of J108 is the setting of the rectifier circuit and the voltage setting of the input
overvoltage protection circuit as shown below.
Doubler Rectifier
L31
CR26
+
AC IN C31
C26 R41 L32
= 280VAC
- C32 - 310VAC
CR8 J108
C27 R42
7/8 4/5
100VAC: Short
220VAC: Open
R19
4
PW CONT
R18
U11
Q12
R21
Q11
4-65
4.12 Change of Power Input Type
1. Jumper setting
JP1:12V
JP1
Board Type
setting
03P9338A
Jumper 12-24 V
03P9338B
03P9338C
Open 24 V
03P9338D
4-66
4.13 Change of Antenna Speed: RSB-096 and RSB-097
Note: The setting of menu box can change the antenna revolution to 42 rpm or 36 rpm. See the
next page for details.
- JP161/162 - JP161/162
- R168 - R168
- TP17 (B.P) - TP17 (B.P)
4-67
4.13 Change of Antenna Speed: RSB-096 and RSB-097
Change of SPEC
1. Make the setting of jumpers JP161 and 162
2. Make adjustments of the B.P frequency according to the antenna speed. Connect the
frequency counter to TP17 and make adjustments at R168.
Adjustment
ANT speed
PWR board Adjusting
(rpm) Check point Adjusting value
position
03PxxxxA, C 24 144 + 5 Hz
R168 TP17 (B.P)
03PxxxxB, D 42/36 252 + 5 Hz (42 rpm)
RSB-097
42/36rpm
ANT Motor power
(24V/20V) RPU-013
BP
TP17
BP The antenna speed can be changed
SPU
p.b.c
ANT Speed
(Hi/Low) PWR p.c.b by “ANT Speed” signals.
(B/D type)
4-68
4.14 Change of Transmission HV setting: HV-9017
Note:
The nameplate of a unit for overseas model includes the description of TX output. In Japanese
model, TX output is known from the description of “MODEL” and “APPROVED TYPE” on the
nameplate.
MODEL FAR-2127-20AF
RCS2FD9-25KP0N-4
R03019
Nameplat of oversea model
2003-12-19
2004-6
4318-0524
PROCESSOR UNIT MU-201CR
RPU-013 XN20AF-RSB-096
4318-0032
25kW. 30kW. 50kW. 60kW
HV-9017 board
J651: HV
4-69
4.14 Change of Transmission HV setting: HV-9017
4.14.1 Setup
Table 4.14.1 Setting of HV-9017
HV-9017
Radar type Transmission RPU-013
Jumper setting
(TR unit) output SER. NO. Type Adjustment Specification*
JP1 JP2
FAR-2x17
12 kW 4317-xxxx A COM-300V COM-330V Adjustment 310 to 350 V
(RTR-078)
FAR-2x27 of Main
25 kW Inverter
(RTR-079)
FAR-2x37S
30 kW Adjustments on
(RTR-080) the VR1 so that
4318-xxxx B COM-500V COM-330V 520 to 580 V
FAR-2827W 34.7-35.3 VDC
25 kW is achieved
(RTR-081)
between
FAR-2837SW TP1 and TP2.
30 kW
(RTR-082)
* As for the measurements, perform on the TB board: HV J651 and J482 on the HV-9017 board. Refer
to the previous page.
TP1 to TP4
JP1
COM 300 V J482: HV output
500 V
JP2
COM 300 V
330 V
4-70
4.14 Change of Transmission HV setting: HV-9017
(CPU)
TX-HV PROTCT RF TXD/RXD
U19
R76
Including HV
RFC p.c.b DATA/ADD.
(03P9346) monitor signal
(GATE ARRY)
Compareter To MD p.c.b
R74
- TX-HV INHBIT N
U22 TRIG 1-4
R77 +
U17
REF 2P5
U4, 5
Note:
1. TX pulse waveform differs depending on the setting of [Menu] -> 0 -> 4 -> 6:MODEL.
Though this is not related to the operation of protection circuit, be sure to check the
MODEL setting.
2. To check TX high voltage on the TR unit side, set [MENU] -> 0 -> 3-> 5:ANT SW to
OFF and stop antenna rotaion. Then, execute a check.
3. The detected TX high voltage is inputted to U19 (CPU) and this value is used for “HV”
indication on the self-test display. The self-test is executed by [Menu] -> 9 -> 8 -> 2 ->
2.
4-71
4.15 Checking of Thermal Relay Setting
SCANNER UNIT
K2 Thermar
relay
K1 3 OUT
3 IN
Ship’s Main
Fig. 4.15.1 AC Motor Power System Diagram
Back of PSU-007:
Check-marked on relevant unit
Crurent
Applicable Type of thermal
Model name of PSU-007 AC motor power set
gearbox relay
value
PSU-007-70-23-S RSB-098 200 (50 Hz)/220 V (60 Hz) 3 φ 2.3 TR-ONH/3 1.7 A
PSU-007-80-10-S RSB-099 380 (50 Hz)/440 V (60 Hz) 3 φ 1.0 TR-ONH/3 0.8 A
PSU-007-72-28-50/60-S RSB-100 220 V (50 Hz) 3 φ 2.8 TR-ONH/3 2.2 A
PSU-007-72-28-50/60-S RSB-101 220 V (60 Hz) 3 φ 2.8 TR-ONH/3 2.2 A
PSU-007-82-12-60-S RSB-102 440 V (60 Hz) 3 φ 1.2 TR-ONH/3 0.8 A
Note: Figures at the end of the model name of the thermal realy represent the minimum
current.
4-72
4.15 Checking of Thermal Relay Setting
Note: Figures at the end of the model name of the thermal relay represent the minimum
current.
ANT ON
RL RFC p.c.b
ANT Power (AC)
RTR-082
RPU-013
4-73
4.16 Sub Monitor
DSub-BNC
Convertor
DVI/RGB IF
G VIDEO
(03P9229A)
DVI-D Monitor B VIDEO For VDR
H SYNC
V SYNC
J617: DISP-1
RPU-013 (FULL LOG)
(TB p.c.b)
J618: DISP-2 RPU-013
(SEMI LOG) (TB p.c.b)
J616: Master J617: DISP-1
OP HD-IN, OP BP-IN, OP VIDEO-IN, OP TRIG-IN (FULL LOG)
* The jumper setting on the SPU board can switch Full-log and Semi-log.
4-74
4.16 Sub Monitor
RPU-013
SPU p.c.b
AD/DATA OP HD OUT-1
ARPA/MAIN CPU HD
U30
SPU FPGA
OP HD OUT-2
OP BP OUT-1
BP
U46
J617, J618
U41
OP BP OUT-2
RF Tx/Rx SUB Display-1, 2
RFC p.c.b OP TRIG OUT-1
TRIG
U40
OP TRIG OUT-2
Echo data
8bit
SEL VIDEO SEL A/D
(U83) (U76)
HD IN
TEST ECHO BP IN
RF unit TRIG IN J616
GAIN/STC CONT
4-75
4.16 Sub Monitor
5 V, 2 ms/div Note: B.P signals from the antenna are converted at FPGA on the
SPU board according to the MODEL setting.
Note:
If the setting of S-band and X-band is not correctly made in [Menu] -> 0 -> 4 ->
6:MODEL, B.P echo presentation in azimuth direction is incorrect.
12 V 12 V
5 V, 1 ms/div 5 V, 5 us/div
4-76
4.16 Sub Monitor
5 Vp-p
5.5 Vp-p
1 V, 10 us/div 1 V, 10 us/div
Trigger
ANT Stop Slave-1 #8 Open: Video (Full-log) ANT Stop Slave-2 #8 Open: Video (Semi-log)
4-77
4.16 Sub Monitor
5 Vp-p
5 Vp-p
1 V, 10 us/div
1 V, 10 us/div
Trigger
1 V/0.5 ms/div
1 V/0.5 ms/div
4-78
4.16 Sub Monitor
4-79
4.16 Sub Monitor
4-80
4.16 Sub Monitor
Level Read
HD 0V ----- +5 VDC to +12 VDC Negative edge
Duty: 50%
B.P 0V ----- +5 VDC to +12 VDC
360 pulses/REV.
Trigger 0V ----- +5 VDC to +12 VDC Positive edge
Video -5 V Negative
R401 TP58
TP58: 2Vp-p
Tx Trigger
Fig. 4.16.15 TP58 on the SPU Board: Slave-1 Input Fig. 4.16.16 TP58/R141 on the SPU Board
4-81
4.16 Sub Monitor
2. Timing adjustment
Do the timing adjustments of slave display by [Menu] -> 0 -> 2 -> 4:TIMING ADJ. See
page.4-14 for adjustments.
Note:
See page.4-20 for the details for operations when the setting is switched to the sub
monitor.
4-82
4.17 Connecting to the FEA-2x07
Procedure
1. Call up the INITIALIZE menu. Press [MENU] key 5 times while holding down the
[HL OFF] key.
2. Make the following setting on the INITIALIZE menu.
1) Set 4 INSTALLATION -> 7 TYPE to “B”.
2) Make the setting of 5 OWNSHIP INFO -> 3 SCANNER POSN.
Note: Make the setting of GPS1 ANT POSN, GPS2 ANT POSN and
CONNING POSN as appropriate.
3) Set 6 ARP PRESET -> 2 TTM OUTPUT to “TRUE”.
4) Set 8 OTHERS -> 5 INS” to “SERIAL or “LAN”.
5) “7 NETWORK”
- Checking of IP address
When FAR-2xx7 and FEA-2x07 are interfaced with each other, set the IP
address as the installaion parameter (LAN RADAR) of FEA-2x07.
3. Select [MAIN MENU].
Set “2 MARK” to “7 INS MARK” and make the setting of the following items as
appropriate.
- USER CHART
- CURVED EBL
- CHART SYMBOL
- ROUTE
Note:
- OFF: NOTE BOOK is not displayed.
- ON: NOTE BOOK is displayed but NOTE BOOK display disappears when
any operation is performed.
- DISPLAY: Select this to recheck disappeared NOTE BOOK.
4.Call up [OS POSN] icon menu and set “1 NAV AID” to GPS2.
The conning position data of FEA-2x07 is inputted as the position data. Talker (II
and EC) set on ECDIS side is displayed as the talker.
4-83
Chapter 5. Updating Program
5.1 Overview of Updating
5.1 Overview
5.1.1 Program file
Programs to be updated are:
- Processor unit: SPU board
MAIN CPU, ARPA CPU, DRAW CPU and FPGA Program
- Transceiver unit: RFC board
RFC CPU
Each program is updated in the same connection and method. The table below shows
program folders and the contents of their files. The sizes of the files are just for
reference.
Note:
1. FPGAROM.HEX, LDFPGA.BIN and UPFPGA.BAT files are added from SPU
program Ver-14 and after. However, Updating FPGA Program restricts that “Ver” of a
SPU board is after “Ver.22.” Refer to the following page for how to recognize the
SPU board Ver.
2. The SPU program corresponding to the C-MAP is 0359223-02.14 and after. The
Fr2107rc.hex file is for the C-MAP file.
5-1
5.1 Overview
3. Batch file
SPU board: 0359204-02.xx
- uparpa.bat
uppg /lf ldarpa.bin /hf arparom.hex /port 1 /sp 9600 /t 9999
- updraw.bat
uppg /lf lddraw.bin /hf drawrom.hex /port 1 /sp 9600 /t 9999
- upmain.bat
uppg /lf ldmain.bin /hf fr2107r.hex /port 1 /sp 9600 /t 999999999
Correspond to C-MAP
uppg /lf ldmain.bin /hf fr2107rc.hex /port 1 /sp 9600 /t 999999999
- upfpga.bat
uppg /lf ldfpga.bin /hf fpgarom.hex /port 1 /sp 9600 /t 9999
5-2
5.1 Overview
5.1.2 Preparation
1. To check program numbers;
Carry out self-test: [MENU]-9-8-2(SELF TEST).
Program numbers are displayed as below.
<SELF TEST>
PROGRAM No. ROM RAM DIP SW
SPU 0359204-02.xx OK OK 0000
RFC 0359202-01.xx OK OK
KEY 0359203-01.xx OK OK
REMOTE1 *******-**.** ** **
REMOTE2 *******-**.** ** **
CARD 0359209-01.xx OK OK 0000 Program numbers are displayed.
PROCESSOR UNIT MONITOR
-12V -12V
3.3V 3.2
5V 4.8
12V 12.0
SCANNER MOTOR 0.0
RF UNIT MONITOR
TEMPERATURE
TUNE IND
HV
R.MONITOR
MAG CURRENT
HEATER
12V
-12V
5V
32V
TUNE OUT
TRIGGER FREQ
ANT SPEED
0 0 0 0 0 0 0 0
28 0
88 0
Note:
The program for KEY, REMOTE 1, and REMOTE 2 is the same.
5-3
5.1 Overview
RS-232C Port
5-4
5.1 Overview
5) The preset data are not changed even after updating unless the program of the CPU
board is substantially changed. If CU-200 is installed, we recommend you to save
the preset data in the CU-200 card as a precaution. See p. 6-45 for details.
6) There is no need to set the data transfer speed of the serial port of the PC.
The communication speed is 9600bps while an updating program is booted and
38.4kbps after updating is started.
The protocols are as follows:
* Format) - Data bit: 8 - Stop bit: 1 - Parity bit: None
* Flow control) - None
7) When the serial port number of the PC is other than “COM-1,” change and overwrite
batch file to the same as a port number of the PC, or changing COM port of the PC
to “COM-1”.
For example, when updating is performed by means of “USB – RS-232C interface,”
may be serial port number (USB) of the PC is other than “1”.
5-5
5.2 Updating Program
Note:
Do not turn off the power during update of DRAW CPU program.
5-6
5.2 Updating Program
6. When the PC displays “[Waiting For Target Wake up…] Time: xx (sec),” turn on the
power to the radar.
7. Updating starts automatically. While updating, the radar screen keep displaying
“Now Initializing….”
5-7
5.2 Updating Program
9. Turn off the power and update a next program. Start from Step 4.
10. When all programs are updated, updating tasks are complete, turn off the power and
get the connection back as it was.
5-8
5.2 Updating Program
Procedure
1. Turn off the radar power supply.
2. Insert a Mini-program card to the Card slot: J206 on the SPU board.
3. Turn on the radar power supply. Nothing is displayed.
4. Automatically, all programs of the SPU board start updating. The CR4 on the SPU
board switch the lights off in the updating. And also, nothing is displayed.
5. When the CR4 on the SPU board blinks, it is completed. It takes about 5 minutes
until the updating end. Nothing is displayed after the updating.
6. Turn off the radar power supply and remove the card.
Card
5-9
Chapter 6. Maintenance
6.1 Self-test
DANGER
Hazardous Voltage
This equipment uses high voltage electricity which can SHOCK, BURN or use
DEATH. Always make sure the electrical power is turned off before attempting to
change a component or inspecting the inside of the equipment. A residual
charge may exist in capacitors, even with the equipment turned off. Always short
all supply lines to the chassis with an insulated screwdriver or a similar tool
before touching the circuit.
6-1
6.1 Self-test
6.1 Self-test
The self-test executes in “[MENU] -> 9 -> 8 -> 2: SELF TEST”. The items of self-tests
are:
- Buzzer check
- Checking of program number
- Checking of PROCESSOR UNIT MONITOR
- Checking of “RF UNIT MONITOR”
- Key checking
- Checking of input sentences of serial ports on the terminal board in the Processor
unit.
6.1.1 Overview
Procedure
1. The self-test can execute in “[MENU] -> 9 -> 8 -> 2 ->2: START”.
2. Beep sounds and the screen as below are displayed.
Checking of the program number, PROCESSOR UNIT, RF UNIT MONITOR and
key check executes on this screen.
<SELF TEST>
PROGRAM No. ROM RAM DIP SW
SPU 0359204-02.xx OK OK 0000 Checking of the program number,
RFC 0359202-01.xx OK OK
KEY 0359203-01.xx OK OK ROM/RAM and DIP switches
REMOTE1 0359203-01.xx OK OK
REMOTE2 0359203-01.xx OK OK
CARD 0359209-01.01 OK OK 0000
RF UNIT MONITOR
TEMPERATURE 33.2
TUNE IND 1.3
HV 517.4
R.MONITOR 1.4
MAG CURRENT
HEATER
2.5
4.1
RF UNIT MONITOR
12V 11.9
-12V -11.5
5V 4.8
32V 31.6
TUNE OUT 15.0
TRIGGER FREQ 1058
ANT SPEED 22.3
0 0 0 0 0 0 0 0
28 0
Key check
88 0
6-2
6.1 Self-test
6.1.2 Description
1. Self-test screen-1
6-3
6.1 Self-test
ROM/RAM, DIP SW
When executing “SELF TEST” or “FACTORY TEST”, ROM and RAM are checked.
See page.6-18 for “FACTORY TEST”.
OK or NG is displayed by the result of the Read/Write check of RAM, and Check-sum
check of ROM.
6-4
6.1 Self-test
Display Description
-12 V -12 VDC output on the PWR board.
3.3 V +5 VDC output on the PWR board is converted into +3.3 VDC and displayed.
5V +5 VDC output on the PWR board.
12 V +12 VDC output on the PWR board, which is adjusted by R26.
Antenna motor output voltage on the PWR board. +24 VDC antenna motor
voltage is displayed by X-band radar. The power supply to the antenna motor uses
a feedback circuit, which detects the antenna revolution speed and make the
revolution constant. Accordingly the voltage changes depending on wind pressure
applied on the antenna and voltage drop on the antenna unit cable. The voltage is
SCANNER
generally +21 VDC to +27 VDC.
MOTER
Note:
Both S-band radars and X-band radars output the antenna motor power of +24
VDC outputted from the PWR board. The S-band radar, however, do not use
the antenna motor power.
6-5
6.1 Self-test
RF UNIT MONITOR
Each monitor-value is detected in the transceiver unit.
Note that monitor values of TUNE IND, R. MONITOR, HEATER, TUNE OUT,
TRIGGER FREQ and MAG CURRENT vary with the setting of the Range/Pulse length.
See pages 6-42 for details.
TEMP OUT AD
U20
TEMP sensor RFC p.c.,b
R.MON(D MON) AD
RU MIC
IF TUNE
A/D
TUNE IND AD
Antenna IF AMP p.c.b TUNE
TRIGGER 1-4
Mag. MD p.c.b
MAG CURRENT (MAG CURRENT LVL) AD
HV(HV PROTECT) AD
Pulse
Transformer
Display Description
TEMPERATURE Detects the temperature of the RFC board.
Tuning indicator voltage outputted from the IF AMP board. It is used for Auto-tuning
TUNE IND
and the tune indicator.
HV voltage outputted from the HV-9017 board in the Processor unit, which is applied
HV to the pulse transformer. In case of 12 kW: 310 to 350 VDC, and 25 kW or more: 520
to 580 VDC.
R.MONITOR DI MONITOR voltage from the MIC
MAG CURRENT Magnetron current, which is detected in the MD board.
HEATER Magnetron heater voltage outputted from the PWR (RF) board.
12 V +12 VDC voltages outputted from the PWR (RF) board.
-12 V -12 VDC voltages outputted from the PWR (RF) board.
5V +5 VDC voltages outputted from the PWR (RF) board.
+32 VDC voltages outputted from the PWR (RF) board. It is used for the power supply
32 V
of the TUNE circuit of the MIC.
TUNE OUT TUNE control voltage of the MIC. It varies with the MIC.
Shows the transmission trigger frequency. It varies with the pulse length/range and
TRIGGER FREQ
indicates the frequency between 450 Hz and 3000 Hz.
The antenna speed is set from the bearing pulse detected on the B.P GEN board. The
ANT SPEED revolution varies with the types of the gearbox, that is 24/42 rpm in X-band and
21/26/45 rpm in S-band.
6-6
6.1 Self-test
FAR-2827W, 2x27
Table 6.1.5 FAR-2827W: RF Monitor Display
Monitor Item L: 48NM M2: 6NM M1: 3NM S2: 1.5NM S1: 0.125NM
TUNE IND 1.6 1.6 1.5 0.7 1.0
R MONITOR 3.9 3.9 3.9 3.9 3.9
MAG
4.6 3.6 2.8 2.5 1.9
CURRENT
HEATER 1.4 1.4 1.7 1.7 1.7
TUNE OUT 16.0 16.0 16.3 16.2 16.2
FAR-2837SW, 2x37S
Table 6.1.6 FAR-2837SW: RF Monitor Display
Monitor Item L: 48NM M2: 6NM M1: 3NM S2: 1.5NM S1: 0.125NM
TUNE IND 1.5 1.7 1.6 1.4 2.6
R MONITOR 4.3 4.3 4.3 4.3 4.3
MAG
4.3 3.9 3.2 2.7 2.0
CURRENT
HEATER 1.5 1.5 1.5 1.8 1.8
TUNE OUT 9.9 10.0 10.1 10.1 9.8
Note:
HEATER voltage is displayed about 1.4 V in the RF MONITOR, but actual heater
voltages are from 7.4 V to 9.4 V. The checkpoint is J833 - #11(+), #12(-) on RF PWR.
See page 6-44.
6-7
6.1 Self-test
Key check
Key check is a function for checking the panel keys.
The drawing on the left below corresponds to the arrangement of the keys, knobs and
trackball of RCU-014 and the drawing on the right corresponds to those of RCU-015
and RCU-016 (but the power key is excluded.)
The boxes numerically displayed are used for checking of the knobs and track ball
showing changes in a range between 0 and 255. Other boxes correspond to keys and the
corresponding key is highlighted when a box is pressed.
0 0 0 0 0 0 0 0
28 0
88 0
RCU-014 RCU-016
When the Trackball control unit RCU-015 is connected with the Remote control unit
RCU-016, both units use the display on the right. The left-side display is not used.
RPU-015 RPU-016
6-8
6.1 Self-test
2. Self-test screen-2
The IEC-61162 sentences received can be checked on the screen. The sentences
displayed are fixed and the data of input sentence is shown. There is no restriction on
the display by IEC versions of input sentences.
<GPS1>: displays position-related data inputted from the [NAVIGATOR] port: J606 on
the TB board.
<GPS2>: displays position-related data inputted from ports other than the
[NAVIGATOR] port on the TB board.
Restrictions of the sentences differs with the setting of “[Menu] -> 0 -> 4 -> 7: Type”.
- When set to the IMO type: Acceptable sentences are IEC-61162 2nd Edition
(Same as NMEA Ver-03), check the Check Sum, Mode Indicator and Status
fields.
- When set to the type other than IMO: There is no restriction by NMEA
versions of input sentences (Same as NMEA Ver-1.5 and 2.0).
<SELF TEST>
<GPS1>
GGA GPGGA,,3512.150,N,13944.000,E,1,,,,,,
GLL
RMC
RMB Displays the GPS data inputted from
VTG
ZDA the [NAVIGATOR] port: J606.
DTM
BWR
BWC
<GPS2>
GGA
GLL
RMC Displays the GPS data inputted from
RMB ports other than the [NAVIGATOR]
VTG
ZDA port: J606.
DTM
BWR
BWC
<SPEED>
VBW
VHW
VDR
<HEADING>
HDT
<NAV DATA>
WPL Displays the data other than the GPS.
RTE
MWV
VWT
VWR
DPT
DBT
DBS
MTW
VDM
To quit press [F1] key
6-9
6.1 Self-test
<SELF TEST>
<AIS>
VDO
Displays AIS data inputted from
VDM the [AIS] port: J611.
<INS>
ZDA
GGA
GLL
OSD
DPT
MWV Displays the data inputted via LAN or from J620selected
DTM
FUGLL by "[Menu]->0->8->5: INS"
PAESP
PAESC
- LAN setting -- [NETWORK] port
PAESF - SERIAL setting -- [TRACK CONTROL] port: J620
PLSPL
PLSPS
PAESW
PAESN
2) Data format
- Data : 8 bits - Stop bit : 1 bit
- Parity : None - Flow control: None
6-10
6.1 Self-test
3) Priority of ports
- The selection of input ports and priorities of GGA, GLL, DTM, RMC and VTG
sentences for position and SOG/COG is determined by the selection of GPS1 or
GPS2 in “1. NAV AID” of the “OS POSN” menu.
GPS-1: J606: NAVIGATOR
GPS-2: J607: LOG < J605: HDG SENSOR
< J620: TRACK CONTROL < J601: RS-232C
< LAN (INS)
- Other sentences
J606: NAVIGATOR < J607: LOG < J605: HDG SENSOR
< J620: TRACK CONTROL < J601: RS-232C < LAN (NAV)
< LAN (INS)
Description Sentence
Target L/L TLL
Radar system data RSD
ARPA target data TTM
Waypoint arrival alarm AAM
6-11
6.1 Self-test
HDG Heading
SPD Speed, Source When data is invalid in VBW
SB 0.0 kt Log Speed
COG Course over Ground
SOG Speed over Ground, Source The mode is No Fix, DR, Manual
OS POSN or SIM mode in GGA, GLL, VTG
DGPS Position
and RMC.
6-12
6.1 Self-test
Pin
Connector Signal I/O Hardware Sentences Remarks
No.
GGA, GLL, RMC, BWR, BWC, RMB,
ZDA, DPT, DBT, DBS, MTW, MWV,
2 RXD IN
J601: RS-232C VWT, VWR, VDR, WPL, RTE, DTM,
RS-232C (Fixed to 4800 bps) VBW, VHW, VTG, HDT, PFEC, GPatt
Note:
3 TXD OUT TLL, RSD, OSD
Not to be outputted on the IMO type.
It is recommended to use 38.4 kbps for HDT
RS-422
1 HDG A with higher rate (40 Hz per example) to allow
J605: IEC61162-1
the ARPA function.
HDG IN IEC61162-2
Related setting:
SENSOR (Variable between 4800
2 HDG B Note Used when “SERIAL” is selected in “[HDG]
and 38.4 kbps )
box menu -> 1.HDG SOURCE”.
GGA, GLL, RMC, BWR, BWC, RMB,
RS-422/C.Loop Position data sentences can be checked on
ZDA, DPT, DBT, DBS, MTW, MWV,
1 NAV A IEC61162-1 <GPS1> on the self-test screen.
J606: VWT, VWR, VDR, WPL, RTE, DTM,
IN IEC61162-2 Related setting:
NAVIGATOR VBW, VHW, VTG, HDT
(Variable between 4800 Used when “GPS1” is selected in
2 NAV B PFEC, GPatt
and 38.4 kbps Note) “[OS POSN] box menu -> 1.NAV AID”.
RS-422/C.Loop
J607: 1 LOG A IEC61162-1
LOG Position data sentences can be checked on
IN IEC61162-2
(Serial data <GPS2> on the self-test screen.
2 LOG B (Variable between 4800
only) Note
and 38.4 kbps )
J608: 1 AD DATA H
Related setting:
A/D 2 AD DATA C
IN C.Loop AD-10 Format Used when “AD-10” is selected in
CONVERTOR 3 AD CLK H
“[HDG] box menu -> 1.HDG SOURCE”.
4 AD CLK C
Note: Variable between 4800 and 38.4 kbps: The receive speed is detected on the radar side and both receive and transmit speeds are automatically
switched among 4800, 9600, 19.2 k and 38.4 kbps.
6-13
6.1 Self-test
1 AIS TD A
OUT ABM, BBM, SSD, VSD
2 AIS TD B
RS-422
J611: 3 AIS RD A On the IMO-type, the AIS is not displayed when
IEC61162-2
AIS DTM is other than WGS-84, “[Menu] -> 4 -> 8:
IN (Fixed to 38.4 kbps) ALR, VDO, VDM, ACK
4 AIS RD B AIS FUNCTION” cannot be set to ON. On other
type, the AIS is displayed even without DTM.
Related setting-1:
Select “REL” or ” TRUE” in “[Menu] -> 0 -> 6
J619: 1 ARPA A IEC61162-1
OUT TTM -> 2.TTM OUTPUT”.
ECDIS (4800 bps)
Related setting –2:
2 ARPA B Select “OFF” in “[Menu] -> 0 -> 8 -> 5.INS”.
RS-422
IEC61162-1 ECDIS-related sentences:
1 TRK TD A
OUT IEC61162-2 OSD, PAESP, TTM, PFEC, RAssd,
(Variable between 4800 RSD
Related setting –1:
and 38.4 kbps)
2 TRK TD B Select “REL” or ” TRUE” in “[Menu] -> 0 -> 6
ECDIS-related sentences: -> 2.TTM OUTPUT”.
J620: GLL, GGA, FUGLL, DTM, OSD, Related setting –2:
TRACK 3 TRK RD A ZDA, DPT, MWV, PAESP, PAESC, Select “SERIAL” in “[Menu] -> 0 -> 8 -> 5.INS”.
CONTROL RS-422/C.Loop PAESF, PLSPL, PLSPS, PAESW,
IEC61162-1 PAESN
IN IEC61162-2 NAV-related sentences: Position data sentences can be checked on the self-
(Variable between 4800 GGA, GLL, RMC, BWR, BWC, test screen.
between 38.4 kbps) RMB, ZDA, DPT, DBT, DBS,
4 TRK RD B MTW, MWV, VWT, VWR, VDR,
WPL, RTE, DTM, VBW, VHW,
VTG, HDT, PFEC, GPatt
6-14
6.1 Self-test
1 RSV1 TD A
IN Undefined
J621: 2 RSV1 TD B
SERIAL I/F 4 RSV2 TD A
OUT Disabled
5 RSV2 TD B
FURUNO network command Note-1
F-NET
Note-1:
ECDIS-related sentence:
Cannot be received when the FURUNO’s LAN
GLL, GGA, FUGLL, DTM, OSD, ZDA,
header is not added.
DPT, MWV, PAESP, PAESC, PAESF,
IN 100 Base-Tx Note-2:
PLSPL, PLSPS, PAESW, PAESN
The FURUNO’s LAN header is added and sent.
INS NAV-related sentence:
Port No. GGA, GLL, RMC, BWR, BWC, RMB,
Related setting-1:
10028 ZDA, DPT, DBT, DBS, MTW, MWV,
Select “REL” or “TRUE” in “[Menu] -> 0 -> 6 ->
VWT, VWR, VDR, WPL, RTE, DTM ,
LAN: 2.TTM OUTPUT”.
VBW, VHW, VTG, HDT, PFEC, GPatt
FURUNO network command Note-2
Related setting –2:
F-NET
OUT 100 Base-Tx Select “LAN” in “[Menu] -> 0 -> 8 -> 5.ISN”.
ECDIS-related sentence:
OSD, PAESP, TTM, PFEC,RAssd, RSD
IN 100 Base-Tx Sentences except for HDG data. Related setting:
NAV Select “ON” in “[OS POSN] -> 3.SIO DATA
Port No. NMEA sentences in use except for HDG LAN OUTPUT”.
10021 OUT 100 Base-Tx When connecting radars to the LAN, it is possible
data.
to send the own data to other radars.
6-15
6.1 Self-test
6-16
6.1 Self-test
7) Acceptable sentences
Table 6.1.11 Acceptable Sentences
6-17
6.2 FACTORY TEST
Procedure
1. Press the [2], [3] and [4] keys while pressing [1:HL OFF] key.
2. Select “4: FACTORY TEST”. The FACTORY TEST screen as below is displayed.
<FACTORY TEST>
PROGRAM No. ROM RAM DIP SW 1 2 3
SPU 0359204-02.xx OK OK 0000 0044 0003 0003
RFC 0359202-01.xx OK OK 0008 0017
KEY 0359203-01.xx OK OK
REMOTE1 0359203-01.xx OK OK
REMOTE2 0359203-01.xx OK OK
CARD 0359209-01.01 OK OK 0000
6-18
6.2 FACTORY TEST
6.2.2 Contents
FPGA program numbers and version of RFC board
The FPGA program numbers of the SPU board and RFC board is displayed.
1 2 3 Display No.
004F 0007 0004 Version of FPGA on SPU board
0009 001F Version of RFC board and version of FPGA
Display 1 2 3
SPU U46: SPU FPGA Ver U12: Echo FPGA Ver U13: DRW FPGA Ver
Note:
Displays version of the RFC board
by HEX and make the version
RFC U17: FPGA Ver
setting on JP3 to 6.
JP3 (BREV 0: 1), JP5 (BREV 1: 2)
JP6 (BREV 2: 4), JP4 (BREV 3: 8)
6-19
6.2 FACTORY TEST
Note:
The item “RFC” of the display No. 1 indicates the history of the hardware function of
the RFC board. The history setting is made by the setting of JP3 to 6. This setting does
not affect any function.
RFC board
New:
RFC board 03P9346-00 03P9346-00A 03P9346-11A
03P9346-33A
J806: 2P connector
(Improvement of None None None Added
Noise- ring)
X-Band radar Available
Common Common Common
S-Band radar
RFC board Ver. 008 009 009 009
03P9244-55E
S-Band radar MD board 03P9244-33E
(J816 is added.)
The J806:2P connector for the S-band radar on the MD board is added in the 03P9346-33A and after.
- In the X-Band radar: J806 is not used.
- In the S-Band radar: Between J806 on RFC board and J816 on MD board are connected.
The MD board is in the 03P9244-55E, RFC board 03P9346-33A and after.
6-20
6.2 FACTORY TEST
Loopback test
The I/O ports are checked by the loopback test.
Procedure
1. Jumper the ports to be loopback on the TB board of RPU-013 as shown below.
2. Press [2], [3] and [4] keys while holding down the [1:HL OFF] key.
3. The [Factory] menu is displayed. Select “4: Factory test”.
6-21
6.2 FACTORY TEST
Test Test
Result Description
item speed
38.4 Loopback test of AIS port J611. In the test, characters of
AIS OK / -
kbps “FAR2107” are sent. If they are received, it is judged as OK.
Characters of “FAR2107” are sent from the SERIAL I/F (TD)
38.4
HDG OK / - J621 to the HDG port J605. If they are received, it is judged as
kbps
OK.
38.4 Characters of “FAR2107” are sent from the J621: SERIAL I/F
LOG OK / -
kbps (TD) to the J607: LOG port.
38.4 Characters of “FAR2107” are sent from J619: ECDIS (TD) to
NAV OK / -
kbps J606: NAVIGATOR. If they are received, it is judged as OK.
38.4 Loopback test of TRK port. In the test, characters of “AR2107F”
TRK OK / -
kbps are sent. If they are received, it is judged as OK.
4.8 Loopback test of J601: RS-232C. In the test, characters of
RS-232C OK / -
kbps “FAR2107” are sent. If they are received, it is judged as OK.
19.2 The command of the test mode is sent to the control unit. If the
KEY IO OK / -
kbps program number comes back, it is judged as OK.
115.2 The command of the test mode is sent. If the program number
RF IO OK / -
kbps comes back, it is judged as OK.
During the test, the display changes in the order of
“1000->0100->0010->0001”. This change is synchronized with
the J612: EXT ALARM output (ON/OFF).
In ALARM-4 alone, ON/OFF operations are opposite to those of
1000-> ALARM-1 to 3.
ALARM 0100-> 1000: ALARM-1 (#1-2), 0100: ALARM-2 (#3-4),
―
IO 0010-> 0010: ALARM-3 (#5-6), 0001: ALARM-4 (#7-8),
0001 NOTE:
The polarity of ALARM-1 to 4 (ON/OFF) depends on the
setting of “[Menu] -> 3-> 6, 7, 8, 9-> 9: ALARM OUT
POLARITY”.
The setting item is not available on the IMO and A types.
6-22
6.3 LED Check
: RPU-013
6.3.1 Processor unit:
1. SPU board
Table 6.3.1 LEDs on SPU board
MAIN CPU
(U21) CR4
(Blink every second)
ARPA CPU
CR8 (U74)
(Blink every
0.5 second)
DRW CPU
(U19)
6-23
6.3 LED Check
2. NET-100
This board is common to CU-200. LED operation is the same.
SPU board
PWR board TX-HV board
NET-100 board
CU-200
NET-100 board
RPU-013
100BASE-T
(RJ-45)
6-24
6.3 LED Check
3. PWR board
Table 6.3.3 LEDs on PWR board
Part Normal
Board Function
number status
Lights on when the over-current of antenna motor power
supply (+24 VDC) is detected. Restart the power to reset.
CR63
OFF Note:
(MTR)
Since the antenna motor of S-band radar is of AC motor
type, +24 VDC antenna motor power supply is not used.
Lights on when 4 to 5A, over-current of power supply for
CR64 (RF) OFF
TR unit (+24 VDC), is detected. Restart the power to reset.
Lights on when 5 to 7A, over-current of Tx-HV power
CR65 supply (+24 VDC), is detected. Restart the power to reset.
OFF
PWR (AC) (Tx-HV) The TX-HV board also has an over-current protection
(03P9339) circuit.
The LED is turned on when input over/low voltage is
and detected. Operation is restarted when the voltage comes
back to the specified voltage range.
PWR (DC)
(03P9338) AC type
Protection DC type
100 VAC 220 VAC
CR23 141 to 282 to
OFF Over 34 to
147 294 VAC
(IN ER) voltage 38 VDC
VAC
148 to - 24 VDC Spc.
170 VAC 13 to 17 VDC
Low 70 to
- 12 VDC Spc.
voltage 80 VAC
7.3 to 8.5
VDC
6-25
6.3 LED Check
CR63 (MTR)
CR63 (MTR)
CR64 (RF)
CR64 (RF)
CR65 (Tx-HV)
CR65 (Tx-HV)
6-26
6.3 LED Check
4. TX-HV board
CR23(GRW)
CR21(RED)
6-27
6.3 LED Check
5. GC-10 board
Table 6.3.5 LEDs on GC board
CR22
CR21
LED1
6-28
6.3 LED Check
6.3.2 RF unit
Table 6.3.7 LEDs on RFC Board
RTR-082: FAR-2837SW
RTR-079, 078: FAR-2xx7
RTR-081: FAR-2827W
6-29
6.3 LED Check
2. RCU-015/RCU-016
Table 6.3.9 LEDs on PNL Board
RCU-015, 016
6-30
6.4 Error Messages
090
100
ARP,
110
AIS DATA BOX
120
Note-1:
TARGET-FULL (AUTO), TARGET-FULL (MAN)
6-31
6.4 Error Messages
6-32
6.4 Error Messages
Note:
- Conditions of the lost targets on the FA-100 are:
LOST When a target cannot be received for 3 minutes 20 seconds or
more, the target becomes a lost target. And, when it is not
received for 3 minutes 20 seconds or more, it is deleted from
the reception file.
- Conditions of the lost targets on the FA-150 depend on the speed:
For instance, the target becomes a lost target in 10 minutes
while the ship stops, and in 7 seconds when the speed is 23 kt
or more. When there is no reception for 400 seconds or more, it
is deleted from the reception file.
Cont’d
6-33
6.4 Error Messages
Cont’d
6-34
6.4 Error Messages
Displayed when water depth is less than the depth set in “[Menu] -> 7
DEPTH
-> 4:DEPTH MARK”.
Displayed when the cross track error is out of the range set in
XTE
“[Menu] -> 8 -> 5: NAV LINE WIDE”.
Displayed when an applicable target enters or leaves the range set in
TARGET ALARM [ALARM1] and [ALARM2]. The setting of IN/OUT (Enter/Leave) is
made in “[Menu] -> 3 -> 2: TARGET ALARM MODE”.
6-35
6.4 Error Messages
Error display
AIS Description
Radar side
side
TX Tx malfunction Transmission malfunction, transmission stop
Possible cause: Antenna damage.
ANT Antenna VSWR exceeds limit
Continues operation is enabled.
TDMA Rx1 board malfunction. Transmission through
CH1 Rx channel 1 malfunction
the corresponding transmitting channel is stopped.
TDMA Rx2 board malfunction. Transmission through
CH2 Rx channel 2 malfunction
the corresponding transmitting channel is stopped.
DSC Rx board malfunction. Transmission through
CH70 Rx channel 70 malfunction
CH70 is stopped.
MKD connection lost MKD connection is disconnected. Continuous
MKD (MKD: Minimum Keyboard operation is enabled. (Actually this display is not
and Display) present.)
External EPFS lost
Data of an external navigation system is discontinued.
EPFS (EPFS: Electronic position
Continuous operation is enabled.
fixing system)
L/L No sensor position in use Position data for use is not present.
No valid SOG information
SOG SOG information is invalid data.
(SOG: Speed Over Ground)
No valid COG information
COG COG information is valid data.
(COG: Course Over Ground)
HDG Heading lost/invalid HDG data is discontinued / invalid.
No valid ROT information
ROT HDG data and $TI-ROT data are not present.
(ROT: Rate of Turn)
6-36
6.5 Replacement of Major Parts
:RPU-013
1. Processor unit:
6-37
6.5 Replacement of Major Parts
2. Antenna unit
Table 6.5.2 List of Major Parts Incorporated in Antenna Unit
6-38
6.5 Replacement of Major Parts
6-39
6.5 Replacement of Major Parts
6-40
6.5 Replacement of Major Parts
Note:
- Changes of the PWR board type can be coped with by the setting of jumper.
See p.4-64 for details.
- Changes of the HV board type can be coped with by the setting of jumper.
See p.4-70 for details.
6-41
6.5 Replacement of Major Parts
2. Replacement of Magnetron
The Magnetron is a ferromagnetic substance. When replacing the Magnetron, remove
your watch (a watch can be damaged) and remove it by using a non-magnetic
screwdriver. The outline of the replacing procedure is as follows:
Procedure:
1. Refer to the photo illustrating part layout in the following pages and remove the
magnetron.
- FAR-2xx7: page. 2-11 - FAR-2827W: page. 2-20
- FAR-2837S: page. 2-24 - FAR-2837SW: page. 2-30
2. Turn the power on and check the magnetron heater voltage.
3. Wait for about 30 minutes in the ST-BY state.
4. Put the radar in the send state in the long range and check the magnetron current.
5. Wait for about 30 minutes in the send state.
6. Execute tune initialize in “[Menu] -> 1 -> 3:TUNE INITIALIZE”.
7. Reset each preset time to “0” in “[Menu]->0->4->8:ON TIME, 9:TX TIME”.
6-42
6.5 Replacement of Major Parts
3. References
1) Method for adjusting magnetron current
Basically, there is no need for adjusting the Magnetron current. Even if a Magnetron
is replaced, it is not needed to adjust it.
- Make a transmission at L pulse and adjust VR1 on the MD board so that voltage
between J3 - #1 and #3 on the RFC board is within the voltage range specified.
6-43
6.5 Replacement of Major Parts
Checking of
heater voltage
(J833-#11-#12)
R28(Mag. H)
Model HEATER
R32(Mag. L) Tx/L
FAR-2x17 7.4 to 7.6
STBY/S
FAR-2x27 Tx/L 6.5 to 7.5
FAR-2827W STBY/S 8.2 to 8.4
FAR-2x37S Tx/L 7.2 to 7.8
FAR-2x37SW STBY/S 9.1 to 9.3
4. Replacement of MIC
If the MIC is damaged, the R. MONITOR values are substantially varied.
When replacing the MIC alone, it may be damaged if radar waves from other ship get
into it. When replacing the MIC, be sure to do replacing works in a room or a ship so
as to prevent radar waves from getting into the MIC.
After the replacement, be sure to execute “TUNE INITIALIZE”.
- Setting of “TUNE INITIALIZE: [Menu] -> 1 -> 3:TUNE INITIALIZE”
6-44
6.6 Saving to Card I/F Unit: CU-200
If the SPU board is replaced, retrieve the file written in “[Menu] -> 6 -> 3”.
When retrieve the INSTALLATION DATA file: Ixxxxxxxx, and if “POWER ON
RESTART” is displayed in the ALERT BOX, turn off the power once.
See the following pages for the items to be written in “8. WR SETTING DATA” and “9.
WR INSTALLATION DATA”.
6-45
6.6 Saving to Card I/F Unit: CU-200
6-46
6.6 Saving to Card I/F Unit: CU-200
Note:
The settings of “[Menu] -> 0 -> 4 -> 4: RADAR NO” and “[Menu] -> 0 -> 7:
NETWORK” are not saved to the RAM card since they are unique data.
6-47
6.7 Battery Replacement of CG-10
CAUTION!
Take care to avoid short-circuit of the battery. This could create a burn or
fire hazard. Do not dispose of battery in a fire or an incinerator; this may
cause an explosion!
The life of a battery is approximately 5 years although it varies with the operating
conditions of the unit. If “HDG” is represented by “000.0” every time the power is
turned off, the battery has come to the end of its life. Disconnect JP8 and replace the
battery. After the completion of the replacement, re-connect the JP8.
Battery
JP8
6-48
6.8 Connection of EG-3000
Setting:
1. Select “EG” in “[Menu] -> 0 -> 8 -> 2:DEMO ECHO”.
2. Select a type other than IMO type in “[Menu] -> 0 -> 4 -> 7:TYPE”.
3. Select “GPS1” in “1.NAV AID” of the [OS POSN] box menu.
4. Select “MANUAL” in “1.SPEED” in the [SPEED] box menu and enter the ship
speed in this menu.
OP VIDEO IN
TB J616 T.B.
EG-3000 1
GND
8 (NH-8P)
(03P9342)
2 7
MASTER
3
4
OP BP IN
5 4
OP HD IN
(NH-11P) 6 2
7 TB J617
8 (NH-8P)
OP TRIG 1
9 6
SLAVE 1
TB J615
+12V
10 1 (WAGO 5P)
GND
11 2 OPTION
NAV-A TB J606
1 1 (WAGO 3P)
NAV-B
2 2
EG NAV NAVIGATOR
(XH-5P) 3
4
5
AD DATA H TB J608
1 1 (WAGO 4P)
AD DATA C
EG AD-10 2 2
(XH-4P) 3
AD CLK H
3 AD CONVERTOR
AD CLK C
4 4
6-49
Chapter 7. Block Description
7.1 Overview
7.1 Overview
The standard supply units are comprised of Processor unit, Monitor unit, Control unit
and Antenna unit (TR unit). Serial signals are used as control signals between each unit.
The ARPA and video plotter functions are incorporated in the SPU board as standard
and a performance monitor is integrated into the Antenna unit as an option. The inter
switch function operates via LAN connection.
7.1.1 Interface
The communication between TR unit and Processor unit is made via RS-422/115.2 kbps,
and the communication between Processor unit and Control unit via RS-422/19.2 kbps,
both using an asynchronous communication method.
The LAN ports of 100 Base-Tx allows the connection with CU-200 or radars of FAR
series. The connection via HUB-100 allows the connection with up to eight FAR-series
radars and up to two CU-200 units. (Maximum 8 ports)
INS (ECDIS) supports both LAN and serial port (RS-422/4800 bps) connection. See
page.6-13 for details of interface of each port.
Sensor Remote
RS-422
Control unit
SXGA
7-1
7.1 Overview
PM
PM Trig
PM Enable Antenna unit
ANT PM Leve
Motor +12/-12V
IF IF AMP*
D MON IF-VIDEO MIX X band: 03P9335A
HD SW Limitter MIC IF AMP* S band: 03P9335B
TUNE
(03P9335A/B)
PIN ATT
+5V
*S-30k up only
MSS Mag./
Pulse TR Cable ATT Data
(MSS-7497) B.W
(MSS-7497A) MBS Enable STC Detect
TUNE Gain TUNE IND
TUNE Gate DI MON out
TUNE
PSU-007 BP GEN MD STC Cont
(03P9347) (03P9244A/B) To PM
PIN ATT Cont
FET ATT
PM Trig
PM Enable Sample Hold
Trig1-4 PM Leve TEST SIG
HD V Trig +12/-12V TEST SIG Enable
BP Short pulse Mag. CUR +12/-12/5V
Heater
Motor 3ph Tx protect
+12V
RFC
(03P9346A)
+12 RF TX Data HEATER
12/25kW only -12V RF Rx Data -12/+5V
TX HV HEATER OFF
+12/+32V
MU-231CR
Processor unit (RPU-013) SXGA
DVI
+12/-12/-5V
TRK RD OPHD/BP/Trig/Video RSV1 TD
EXT ALM ACK ANT 12V ON RSV2 TD
EXT ALM1-4 GC LED/HOLD/UP/DOWN RSV3 TD
KEY TX/RXD AIS TD/RD NAV RD
LED RS232 TX/RX LOG RD ARPA TD
HOLD -12/Vcc RF Tx/Rx Data AD-10
UP AD-10 GC 5V GYRO RD OP1 HD/BP/Trig/Video
DOWN +24/+12V OP2 HD/BP/Trig/Video
TX HV MOTOR
ANT ON
ANT SPEED R/G/B
BP
24V HV POWER H-SYNC
MONITOR/
GC-10 TX HV (AC: 03P9339) RGB V-SYNC
(64P1106A) (HV9017) DVI IF BUFFER VDR
(DC: 03P9338) 5/+12/-12V
MON MOTOR VLT SPU
POWER FAIL (03P9337) Max 8 port
LAN LAN
NETWORK HUB
Ship’s Main FIL (HUB-100)
(AC: 03P9341) NET-100
(DC: 03P9352) (03P9332)
CARD IF
(CU-200)
7-2
7.1 Overview
RSB-103
PM ANT
Motor
HD SW
BP GEN
PM Trig (03P9347)
PM Enable
PM Leve HD
+12/-12V
BP
TB
(03P9349A) Antenna unit
PM Trig
PM Enable
PM Leve
+12/-12V
RTR-081
T/R unit
IF
DI MON IF-VIDEO MIX
Limitter IF AMP
MIC (03P9335A)
TUNE
PIN ATT
+5V
Mag./
Cable ATT Data
Pulse transformer B.W
MBS Enable STC Detect
TUNE Gain TUNE IND
TUNE Gate DI MON out
TUNE
MD STC Cont
(03P9244E) PIN ATT Cont
FET ATT
Sample Hold
Trig1-4 TEST SIG
V Trig TEST SIG Enable
Short pulse MUG. CUR +12/-12/5V
HD Heater
BP Tx protect
+12V
RFC
(03P9346A)
+12 RF TX Data HEATER
-12V RF Rx Data -12/+5V
+12/+32V HEATER OFF
MU-231CR
Processor unit (RPU-013) SXGA
DVI
+12/-12/-5V
TRK RD OPHD/BP/Trig/Video RSV1 TD
EXT ALM ACK ANT 12V ON RSV2 TD
EXT ALM1-4 GC LED/HOLD/UP/DOWN RSV3 TD
KEY TX/RXD AIS TD/RD NAV RD
LED RS232 TX/RX LOG RD ARPA TD
HOLD -12/Vcc RF Tx/Rx Data AD-10
UP AD-10 GC 5V GYRO RD OP1 HD/BP/Trig/Video
DOWN +24/+12V OP2 HD/BP/Trig/Video
TX HV MOTOR
ANT ON
ANT SPEED R/G/B
BP
24V HV POWER H-SYNC
MONITOR/
GC-10 TX HV (AC: 03P9339) RGB V-SYNC
(64P1106A) (HV9017) DVI IF BUFFER VDR
(DC: 03P9338) 5/+12/-12V
MON MOTOR VLT SPU
POWER FAIL (03P9337) Max 8 port
LAN LAN
NETWORK HUB
Ship’s Main FIL (HUB-100)
(AC: 03P9341) NET-100
(DC: 03P9352) (03P9332)
CARD IF
(CU-200)
7-3
7.1 Overview
RSB-104/105
PM
ANT
Motor
HD SW
BP GEN
(03P9347)
PM Trig
PM Enable
PM Leve HD
+12/-12V BP
TB
(03P9349) Antenna unit
RTR-082
T/R unit
IF
DI MON IF-VIDEO MIX
Limitter IF AMP
MIC (03P9335B)
Motor 3ph TUNE
PIN ATT
+5V
Mag./
Pulse transformer Cable ATT Data
B.W
MBS Enable STC Detect
TUNE Gain TUNE IND
TUNE Gate DI MON out
TUNE
MD STC Cont
(03P9244E) PIN ATT Cont
FET ATT
Sample Hold
Trig1-4 TEST SIG
V Trig TEST SIG Enable
Short pulse MUG. CUR +12/-12/5V
Heater
HD Tx protect
BP +12V
RFC
(03P9346A)
+12 RF TX Data HEATER
-12V RF Rx Data -12/+5V
+12/+32V HEATER OFF
HDG SENSOR
LOG PM Trig PM Trig PWR +24V
PM Enable
PM Enable
PM Leve (03P9348)
PC PM Leve
+12/-12V
MOTOR ON +12/-12V TX HV 25kW only
NAV DATA +12V +24V
ECDS
AIS TB
TRACK CONTROL (03P9349A)
AD-10
ALARM IN/OUT
+24V
TX HV MU-201CR
RF TX Data
MOTOR IF-VIDEO MIX
RF Rx Data
MU-231CR
Processor unit (RPU-013) SXGA
DVI
+12/-12/-5V
TRK RD OPHD/BP/Trig/Video RSV1 TD
EXT ALM ACK ANT 12V ON RSV2 TD
EXT ALM1-4 GC LED/HOLD/UP/DOWN RSV3 TD
KEY TX/RXD AIS TD/RD NAV RD
LED RS232 TX/RX LOG RD ARPA TD
HOLD -12/Vcc RF Tx/Rx Data AD-10
UP AD-10 GC 5V GYRO RD OP1 HD/BP/Trig/Video
DOWN +24/+12V OP2 HD/BP/Trig/Video
TX HV MOTOR
ANT ON
ANT SPEED R/G/B
BP
24V HV POWER H-SYNC
MONITOR/
GC-10 TX HV (AC: 03P9339) RGB V-SYNC
(64P1106A) (HV9017) DVI IF BUFFER VDR
(DC: 03P9338) 5/+12/-12V
MON MOTOR VLT SPU
POWER FAIL (03P9337) Max 8 port
LAN LAN
NETWORK HUB
Ship’s Main FIL (HUB-100)
(AC: 03P9341) NET-100
(DC: 03P9352) (03P9332)
CARD IF
(CU-200)
7-4
7.2 Antenna Unit
1. Control signals
The RFC board and the SPU board of the Processor unit communicate with each other
through RS-422/115.2 kbps by the asynchronous communication method. The overview
of control signals is shown below.
Serial data sent from the SPU board to the RFC board includes GAIN, STC and TUNE
control signals. These signals are processed on the RFC board to control the MD board,
IF board, PWR (RF) board and MIC circuit of the TR unit. The RFC board converts
head line signals, bearing signals, TUNE IND voltage, Magnetron current, DI-Monitor
voltage, and each supply voltage monitored on the TR unit circuit into serial data and
send them to the SPU board.
TR/SCANNER unit
TUNNING
IF PIN ATT
MIC
(03P9335) IF(60MHz)
DI Monitor
Processor unit
(RPU-013) B.W
GAIN/STC IF-Video Sig.
MBS
TUNU
TUNE IND
DI Monitor
Mag.
TUNE GATE
FET ATT
PULTH WIDTH PIN ATT
GAIN GAIN PULSE
STC STC Transformer
FTC TX Trigger
VRM/EBL TUNU
Track Ball MBS
Key SW PM Lelvel/Enable
TRIG
CONT. Power SW RF Tx data TRIG
unit TRIG
SPU HD / BP
TUNE IND
TRIG
(03P9337) Mag.-Current RFC HEATER MD
DI-Monitor (03P9346A) Short pulse
(03P9244)
RF Rx data TX-HV PROTECT
MUG. Current
IF- Video SIg. MIX
V TRIG
Monitor Video Sig.
unit
-12V
+5V
+12V HD BP GEN
+32V BP
HEATER (03P9347)
7-5
7.2 Antenna Unit
4. Monitor of TR unit
The RFC board detects TUNE IND voltage, Magnetron current, DI-Monitor voltage,
and each supply voltage from the circuits. Detected signals are converted into serial data
and sent to the SPU board. By executing [Menu] -> 9 -> 8 -> 2:Self Test, values
detected in the TR unit can be monitored. See page.6-6 for details.
5. HD and B.P
HD and B.P signals are sent from the B.P GEN board to the RFC board. B.P is
outputted at 265 pulses/rev on the S-band radar and 360 pulses/rev on the X-band radar.
These signals are subjected to waveform shaping on the RFC board, converted into
serial data and sent to the SPU board.
Memory Application
The circuit of U17 (FPGA) is
written on it. When the power
ISP PROM
U26 XC18V01S020I is turned on, the program is
(In System Programming)
sent to the FPGA to start the
FPGA.
U28 MBM29LV800BA 90 PFTN 8 M Flash-ROM RFC CPU program
U27 μPD441000LGU B85A 1 M SRAM: RFC CPU work memory
7-6
7.2 Antenna Unit
U17
(FPGA) V TRIG
U6 96MHz
Q1, Q5, Q6 TRIG 1
CLOCK
XC2100E-6TQ144I Q2, Q7, Q8 TRIG 2
RPU-013 BVER 0-3 Q3, Q9, Q10 TRIG 3
Q4, Q11, Q12 TRIG 4 MD
JP3 -J P5 SHORT (03P9244)
3.3V
Vcc INT TX HV INHBI TX-HV PRTECT
U25 U22
2.5V
M3 - L
MAG DETECT S - M2 U8 MAG-CUR-IN
HEATER
U26
(EEPROM)
Data D0-7
ADD. AD1-19
U23
PM Trig PM Trig
PM Enable
PM PM LEVL
INT BP/INT HD
INT UART RX
INT UART TX
FPGA Reset
CLK 16MHz
+12V 3.3V
U28 U27
INT TRG
2P5(2.5V)
U4/U5 (Flash ROM) (RAM)
Rer. VOL
CS/WR/RD
U23 PM Enable
U12 PM LEVL
U30
Reset U29
(Reset)
PROTECT AD
TUNE SYNC
U20 TEMP OUT TUNING BIAS
TUNE SCLK U18
(TEMP. DET) TUNE DIN (D/A) 2.5V
SHORT U3/21
2.5V
U12, 1
U19 TUNE SYNC
U13 TUNE
TUNE SCLK
(RFC CPU) TUNE DIN
(D/A)
Q13
TB J917
Motor ON
U3 IF
M30620FCNFP SDATA/CLK/DATAE
(03P9349) TX SIG
U11
VBW A/B
(03P9335)
J917 U21
BUZ OUT TUNE GAIN
TB803
P12V AD P12V
U12
STC ATT(NC) ISTC ATT P5V AD P5V PWR(RF)
P32V AD P32V
N12V AD N12V
(03P9348)
N12V AD N12V
7-7
7.2 Antenna Unit
Types of
Remarks
MD board
03P9244A For X-band, 12 kW (RTR-078)
03P9244B For X-band, 25 kW (RTR-079, 81)
03P9244E For S-band, 30 kW (RTR-080, 82)
TRIG
TRIG
TRIG
TX data TRIG TX-HV PULSE
RX data
RFC HEATER MD Transformer Mag.
(03P9346A) V TRIG (03P9244)
HEATER
TX-HV PROTECT
MAG. Current
Short
TX-HV
+12V
R3, 4 +12V K1 K4
TX PROTECT
R41, 42
CR1, 2
L1
L4
[J812-10]
R40
Q13, 14 Q15, 16
Q3 TX Pulse
TRIG. 3
[J812-3]
Short Pulse Middle Pulse Long Pulse
Q17, 18 Q19, 20
Q4
TRIG. 4
[J812-4]
V TRIG
[J812-5]
+12V SW REG. VR1
(U1, Q23, U2/Q21
[J812-6] CR4, CR4)
S
Short Pulse(S1) [J812-9]
7-8
7.2 Antenna Unit
1. TX trigger
Four triggers different in pulse length to each drive circuit of the MD board. These
outputs are combined to create high-voltage TX pulses. The waveform of short and
middle TX pulses is a triangular wave. In signal processing, it allows suppressing
relatively weaker echoes such as sea clutter on short range. The photos below show
examples of waveforms of detected TX output of the X-band/25 kW radar.
The pulse length at the point 3 dB below the peak is defined as the pulse length.
0.18 us
0.5 us
1.32 us
200 ns/div
Photo 7.2.3
(e.g.) Waveform of 25 kW L pulse TX output
7-9
7.2 Antenna Unit
VR1
For adjustment of
Magnetron current at
VR1 on the MD board
(No need for adjustment
in the field)
R75
(CPU)
R76
Compareter To MD p.c.b
R74
- TX-HV INHBIT N
U22 TRIG 1-4
R77 +
U17
REF 2P5
U4, 5
7-10
7.2 Antenna Unit
4. RF circuit
Magnetron
While the Magnetron is not operating, TX high voltage (TX-HV) runs through R1/2,
and is changed on capacitor: C1-4. When trigger pulse is applied to MOS-FETs Q1 to
Q4, the FET is turned on and discharges C1 to C4. Voltage is increased on the primary
winding of the pulse transformer and high voltage of 6 kV to 8 kV is generated on the
secondary winding to make the Magnetron oscillate.
Limitter
MIC
Mag. Current
Tx-HV Pulase trans
Heater Heater
Magnetron
RF PWRp.c.b L3
Trigger
R34,35
Charge
R41,42
CR1,2
K1
L1 2 6 4 C801
7-11
7.2 Antenna Unit
- CR802, 803
CR802 and 803 serve to protect the Magnetron. When the trigger is switched from
ON to OFF, counter-electromotive force (overshoot) generated on the Magnetron is
released to the GND line.
- L3 (MD board)
L3 serves to protect the heater power supply circuit. L3 prevents the leakage of
high voltage generated at the pulse transformer from flowing to the heater power
supply circuit.
Circulator
The radar antenna is used commonly for sending and receiving. The circulator performs
switching between sending and receiving. The circulator has three I/O ports and has a
permanent magnet and ferrite core arranged in the center. It serves to output
electromagnetic waves coming from one port to a particular direction. For instance,
electromagnetic waves coming from a port connected to the Magnetron are outputted to
the antenna connecting port and not outputted to a port connected to the MIC to protect
the receiving circuit from a large level of electromagnetic waves. During receiving
signals, receiving waves from the antenna are outputted to the MIC connecting port to
reduce the loss of receiving waves.
Receiving circuit
Receiving waves from the circulator are inputted to the MIC via a diode limiter or TR
limiterNote. If strong sending waves are inputted from other ship, there is a risk of the
MIC being damaged. To protect the MIC from damage, the diode limiter attenuates
strong sending waves. The MIC is comprised of a local oscillation circuit, a LNA circuit,
PIN ATT circuit and a frequency conversion circuit, which converts received signals to
IF signals of 60 MHz.
Note:
- Diode limiter: FAR-2xx7, FAR 2x37S
- TR limiter: FAR-2827W, FAR-2837SW
7-12
7.2 Antenna Unit
03P9335A 03P9335B
IF board for X-band radar IF board for S-band radar
The IF board is comprised of a video detection circuit and the semi-log amplifier circuit
of IF signals (60 MHz). IF signals of 60 MHz and video signals are superimposed and
outputted from the IF board to the Processor unit. Video signals are outputted to allow
connection to an existing type of a sub monitor.
RFC (03P9346A)
PIN ATT CONT
U10 FET ATT
TUNE GATE
TX data SAMPL HOLD
MSB ENABLE
TEST SIG ENABL TUNNING
RX data U17 TEST SIG
(FPGA) PIN ATT*
Data D0-7 U16 STC-CONT +5V* X/S band Echo
(D/A) MIC
DI-MONITOR
STC DETECT
Data D0-7 U7 IF(60MHz)
(A/D)
+12V / +5V / -12V
IF X band* S band*
2.5V (03P9335) PIN ATT none
TUNE SYNC U12, 1 +5V +9V
U13 TUNE
TUNE SCLK (D/A)
TUNE DIN
MIX Sig.
IF SIG.(60MHz)
and
Video SIG.
7-13
7.2 Antenna Unit
TUNE GATE N
J821 1.SDATA Hi: Disale
2. CLK Lo: Enable
3. DATEN CR2 U6 TUNE IND
4, 7, 11. GND Q7,8 BPF U4 (DET) U5 U5
5. VBW B
6. VBW A
8. STC DETECT C28
9. TUNE GAIN Hi: SW ON
10. TUNE IND TUNE GAIN Lo: SW OFF
12. MSB ENABLE U23 S AMPLE HO LD
13. TUNE GATE N S
14. SAMPLE HOLD M, L
T5
Q1 U20 U21 CR10 Q4 U22
IF IN (60MHz)
U27 U28 U16 HPF
[J824]
60MHz IF SIG.
VGA
D-MONI-IN D-MONI-OUT
(0 - 120mVdc) (0 - 2.5Vdc)
U18
[J825-7]
TUNNING TUNE
[J825-1]
IF signals of 60 MHz from the MIC are separated into the tuning amplifier Q7, 8 and
the IF amplifier on the Q1 side. IF signals are separated at U22 to the video detection
circuit on U3 side and the 60 MHz semi-log amplifier on T5 side. Respective outputs
video signals and 60 MHz IF signals are superimposed and sent to RPU-013. At the
input stage of SPU board, superimposed signals are separated at HPF and LPF.
7-14
7.2 Antenna Unit
- VBW-A, B
Tuning circuits are switched to achieve the required bandwidth for improving S/N
of video signals. They are switched according to pulses of S1/2, M1/2/3 and L
pulse.
- STC DETECT
This is a signal to create the AUTO STC curve.
- MBS ENABLE
This is a signal to reduce main bang caused by leaked TX signal. The gain at Q4 is
reduced for the set time. This is the setting of the gate time in [Menu] -> 0 -> 2 ->
5:MBS. This operation starts a little earlier than the TX trigger.
- D MONI OUT
MONI OUT signals are monitor signals of the MIC. Self-test is executed by
[Menu] -> 9 -> 8 -> 2 to check values in RF MONITOR.
- TUNE
This is TUNE control signal inputted into MIC.
7-15
7.2 Antenna Unit
- FET ATT N
This is a control signal for adjusting the ring suppression. When the control time of
the MBS is complete, this signal starts to reduce the gain of Q1 to activate the ring
suppression. The larger is the setting value of [Menu] -> 0 -> 2 -> 0:Ring
Suppression, the more extended is the time for enabling the ring suppression.
- STC CONT
This is the STC control signal to control the gain of U27 and 28.
RPU-013
U19
(RFC CPU)
RFC (03P9346A)
1. B.P signal
B.P signals are created by passing the slits of timing disk through the photo-interrupter
on the B.P GEN board. The timing disk is mounted on the rotary joint shaft in case of
the S-band radar and on the drive gear shaft in case of the X-band radar. The number of
pulses generated from the B.P GEN board is 256 pulses/rev of the antenna on the
S-band radar and 360 pulses on the X-band radar. B.P signals outputted to Slave-1 and
Slave-2 are converted at SPU FPGA on the SPU board and outputted at 360 pulses both
on X-band and S-band radars. See page.4-68 and 4-76 for related information.
7-16
7.2 Antenna Unit
2. HD signal
HD signals are detected by turning on and off the lead switch by the magnet mounted on
the drive gear. This output pulse length varies with the antenna rotation. The period in
which the heading pulse is turned on is in a range of 0 to 90 degrees. The duty ratio is
1:4. See page.4-77 for related information.
Drive gear
Driven gear
J901
1. HD
2. GND
3. BP
4. N.C
5. +12V
+12V
Q3
BP
R4 R7 U1
R13
C4
R3
U3
Q4
R40 HD
[J902-2] [J902-1]
Heading SW
(Reed SW)
magnet
Antenna Motor
7-17
7.2 Antenna Unit
Difference
Name of Applicable
Heater V Heater V
PWR(RF) radar type JP21 R29
(Short pulse) (Long pulse)
X band
03P9348A Open 2.2 k 7.5 V ----
6/12 kW
03P9349B X band 25 kW Open 2.2 k 8.3 V 7.0 V
03P9350C S band 30 kW Short 3.3 k 9.5 V 7.7 V
When supply voltages are supplied from the Processor unit, line voltages drop by the
antenna cable. It causes differences in potential on the ground between the Processor
unit and Antenna unit, thereby resulting in unstable voltage on the earth lines of cables.
For this reason, the power supply to the Antenna unit is featured as follows:
The power to the Antenna unit is supplied in +24 VDC alone except for the TX-HV and
motor line. Required voltage is generated in the Antenna unit based on this power
supply.
HV p.c.b
TX HV MD p.c.b
SW REG. REC
7-18
7.2 Antenna Unit
L11,CR11,C14
CR2 L2
Q3(2SJ265) U11 TP3
(D4F60) (SI 8120) REC +12V
+24V +12V
VOLTAGE
(L1) 60kHz CONTROL R52,59
FILTER PR5V
-24V TP1 R13-16
PR+5V SS L5
U51 TP7
U12 IPk
(uPC317HF)
U41 CR52,C51
+5V
Vcc (MC34063AP1) SW +32V
U1 REG Q11,C13 REC Serise
(AN78L05) COMP VOLTAGE REG
Low -SOFT CONTROL
Voltage START
Protect - Output R62
CONT R57 Q41(2SJ256)
U2(M519578FP) TP6
Q1 CR41,C45
RT41 -12V
REC
L3
L21CR21,C24 TP4
U21 HEATER H
(SI 8015) REC
VOLTAGE R28 J833
CONTROL
HEATER V
125kHz
R32
SS
1. -12V
Q22 JP21
2,7,9,12. GND
C23
HEATER OFF 3. +5V
4,5. +12V
6. +32V
8. HEATER VLT
8. HEATER OFF
L31,CR31,C38 10. HEATER H
L4 U31 TP5
(SI 8010) REC +5V
VOLTAGE
CONTROL PR5V
R47,47
250kHz ss
U22
Q31,C33
-SOFT
START
- Output
CONT
7-19
7.2 Antenna Unit
7-20
7.2 Antenna Unit
MSS7497A MSS7497
ANT motor power supply: 380/440VAC ANT motor power supply: 200/220VAC
Since the antenna size of S-band radar is large, there is a risk that the antenna revolution
mechanism and motor may be damaged due to too large loads if the rated voltage is
applied to the antenna motor suddenly. To prevent this, the antenna revolution is
generally increased without applying the rated voltage onto the motor at the time of
power-on. After rotating loads are decreased, the rated voltage is applied. At the time of
power-on, only two phases of V and W are connected to the motor to make the motor
rotate slowly. The switching circuits of Q1, 2 and 3 are controlled by voltage generated
by full-wave rectification to change the conduction angle of the remaining one phase. S
7-21
7.2 Antenna Unit
- When the stationary state of the antenna rotation has been achieved:
C3 is recharged and maintains about 7.5 VDC.
C4 is recharged through Q1 and Q2 -> Q3 is turned on -> U2 and U3 are turned on ->
C4 is discharged through Q3. In this way, pulses to control U2 and U3 are generated
at C4 and Q3.
200 msec
Power ON
2 6msec >1.2msec
At the time of Power-on (Slow start) Stationary state of the antenna rotation
7-22
7.2 Antenna Unit
The tuning value obtained in full search and small search is saved at U27 (SRAM) of
the RFC board. Searching is performed based on TUNE IND signals.
Small
Tracking Small search
TUNE Initialize Tracking stop search Tracking Tracking
32V
ST-BY Tx
Tune Volt
5V
Changing
Pulse wide
5V
Time
TUNE IND
3V
1V
LP LP M3 M2 M1 S2 S1
Pulse wide
Time
7-23
7.2 Antenna Unit
- Full search
The full search is performed to find the tuning point where the tuning indicator
voltage (TUNE IND) becomes largest within a tuning voltage (TUNE) range
between about 5 V and 25 V. The full search starts by executing [Menu] -> 1 ->
3:TUNE INITIALIZE.
- Small search
The small search is performed to find the tuning point where the tuning indicator
voltage (TUNE IND) becomes largest within a range of +2.5 VDC with the tuning
point obtained in the full search at the center.
The small search is performed as follows:
1. [Menu] -> 1 -> 3:TUNE INITIALIZE is executed, and small searches are
repeated from long pulse to short pulses and respective tuning points are
saved.
2. When operation is switched from ST-BY to TX, two small searches are
repeated based on tuning points of pulse length saved in Step 1. Then the
tuning tracking operation starts.
3. When the pulse length is changed, one small search is performed based on the
tuning points of pulse length saved in Step 1. Then the tracking operation
starts.
- Tuning tracking
The tracking operation is performed every minute.
Tune voltage is changed.
2. Manual tuning
When the operation is changed from the Automatic tuning to the Manual tuning, the
voltage value manually set in the previous time is retrieved. The variable range for it is
5 VDC to 25 VDC. In the Manual tuning, the tuning tracking operation is not performed.
When the operation is changed form the Manual tuning to the Automatic tuning, two
small searches are performed for the pulse length based on the tuning value obtained in
[Menu] -> 1 -> 3:TUNE INITIALIZE.
7-24
7.2 Antenna Unit
STC CONT
IF board
STC DETECT
RFC FPGA
Range Sweep
- Model
A sector - STC Condition
- SEA Condition A/C SEA VR
- Default ANT height
Average of each range - Near/Mid/Far STC curve
10 sec
A+1 sector
7-25
7.2 Antenna Unit
The figure below shows sea clutter and STC CONT voltage created by averaging the
sea clutter level. For instance, if a strong sea clutter signal ahead is erased by the manual
STC, weaker target echoes behind are also erased. If the STC is adjusted so as to leave
echoes behind, sea clutter signals ahead remain. In such a case, optimum pictures are
obtained on the whole by STC-controlling of sea clutter different by each bearing
according to each bearing.
Mid
Near
7-26
7.3 Processor Unit: RPU-013
RFCp.c.b
HDG SENSOR (03P9346A)
LOG
TRACKBALL
PC (RCU-015)
NAV DATA
ECDIS
IF-VIDEO MIX
STD CONT
AIS (RCU-014)
RF TX Data
TRACK CONTROL
Slave Display 1
Slave Display 2
SYSTEM FAIL
AD-10
(FULL-LOG)
POWER SW
(SEM-LOG)
RF Rx Data
ALARM IN/OUT
KEY TX/RD
MOTOR
Master
TX HV
I/O port
+24V
+12V
TRK RD OPHD/BP/Trig/Video
TB EXT ALM ACK ANT 12V ON
EXT ALM1-4 GC LED/HOLD/UP/DOWN RSV1-3 TD
(03P9342) KEY TX/RXD AIS TD/RD NAV RD
RS232 TX/RX LOG RD ARPA TD
-12/Vcc RF Tx/Rx Data AD-10
GC 5V GYRO RD OP1, 2 HD/BP/Trig/Video
+12/-12/-5V
Processor unit
+24/+12V
(RPU-013)
MOTOR
DOWN
TX HV
AD-10
HOLD
LED
UP
ANT ON
ANT SPEED R/G/B
24V- BP H-SYNC
HV POWER V-SYNC
GC-10 TX-HV (AC: 03P9339) RGB
(64P1106A) (HV9017) DVI IF BUFFER
(DC: 03P9338) 5/+12/-12V
MON MOTOR VLT SPU
POWER FAIL LAN
(03P9337) NET-100
Ship’s Main (03P9332)
FIL
(AC: 03P9341) SXGA
(DC: 03P9352)
SXGA
7-27
7.3 Processor Unit: RPU-013
1. Block diagram
J651:HV
TX HV
TX-HV J613: SCANNER UNIT
+12V
J652: POWER
POWER SW
J602: KEY
PWRp.c.b +24V
MOTOR VOLT
J610: SCANNER UNIT
OP BP2
J609: IF VIDEO
Phot-coupler
EXT ALM-ACK
CR11
SYS ACK
J622: KEY
KEY TXD/RXD-A/B
J602: KEY
ANT 12V ON Q5 ANT ON/+12V
J604: SPU-007
GC LED/HOLD/UP/DOWN
J603: GC-10
-12V Vcc(+5V) +12V
J614: CARD I/F POWER
+12V/+5V/-12V
J615: OPTION POWER
TB p.c.b(03P9342)
7-28
7.3 Processor Unit: RPU-013
The figure below shows the interface of the AIS and HEADING SENSOR ports. Inputs
and outputs are isolated by LC1535 both on the TX and RX lines. The resistor of the
RD line is the terminating resistor. Loads on the talker side set ON/OFF of the
resistance. See page.4-39.
TERMINAL p.c.b
GND2
Position for setting of
Floating
common terminating resistor
2 3 11 14
ST1 ST2 AIS port: [J656]
GND2 Vcc2
1 Vcc 420kHz HDG port: [J655]
A RDx-B
16
RD RO 3
28 R 330 x 3
B
1 2 RDx-A
AIS/HDG sensor
RE 15
27
RO2
17
IEC-61162-2
LTC1535
Y TDx-B
DE 13
26
TD DI D
TDx-A
25 Z 12
SLO COMMON
4 GND 18
GND
Logic common
Alarm outputs are contact signals by MOS-FET contact and items to be outputted as
alarms can be selected in [Menu] -> 3 -> 6, 7, 8 and 9. The EXT ALARM terminal on
the TB board operates as follows.
- ALM-1, 2, 3: Normally closed and the driver is U10-12 (PS7241 1B).
Note: Closed during power-off and initializing.
- ALM-4 : Normally opened and the driver is U9 (TLP176G TP).
Note: Opened during power-off and initializing.
See page.4-58.
400V max.
100mA max.
Terminal p.c.b
7-29
7.3 Processor Unit: RPU-013
2. Connector
Table 7.3.1(1/2) Connector on the TB board
7-30
7.3 Processor Unit: RPU-013
7-31
7.3 Processor Unit: RPU-013
1. Block diagram
The SPU board performs picture, LAN, video amplifier, ARPA and video plotter
processing in addition to the control over the whole radar. The CPU is comprised of
three components of Main CPU, ARPA CPU, DRW CPU.
+5V/+3.3V/+12V/-12V
TX ON U38
(From MAIN CPU) A/D
MON MOTOR
(From PWRpcb)) MONOTOR
U3
Display
MEMORY
U86:Video DET Echo Data U12 U2
U85 Echo
Echo MEMORY
IF-VIDEO-MIX 30M SEMI-LOG FPGA U1
U87
U83(Selecter)
HPF Trail
FULL-LOG MEMORY
30M U76
LPF A/D U46
FULL-LOG 8bit SPU
OP1-VIDEO OUT JP6 FPGA U15
OP-VIDEO IN
S1
U9
U64 SDRAM
CR8
FROM U22 To Display
SDRAM
U4
U48 DVI
DATA/ADD BUS
CR4 U6
NAV RD FROM
U52
RSV1 TD
RSV2 TD
ARPA TD U21
MAIN CPU
AIS TD GC LED/UP/DOWN/HOLD
ANT ON
KEY TD/RD EXT ALM ACK
TRK TD/RD EXT ALM 1-4
Serial I/O
U73
RS232C Driver
7-32
7.3 Processor Unit: RPU-013
The figure below shows the overview of functions of FPGA. See page.7-37 for specific
signal processing.
NET-100
(LAN I/F)
ARPA CPU
Echo select
- TX data GEN
(Correlation)
ACQ
processing
Echo data
Echo detct
- Inter SW
Tracking
- RX data
- LAN I/F
CPA/TCPT
Echo data
memory
QV echo
RO-XY converter
FULL LOG Video
Video Contrast
FTC processing
Selcter
(Auto Rain)
8 8 8 8 8
ES
OP video signal AD Con.
IR
ARPA test echo
Trailing data
processing
Test echo/HD/BP/TRIG ARPA
test echo
Trailing data
memory
RO-XY converter
SAMPL TRIG
From/To TX TRG Trigger GEN
RS-422
AZ counter
HD HD
Decode BP PLL BP(8192)
GYRO data
Display data
HD
To
processing
BP
External Display SAMPL TRIG
Display data
RF TXD
UART
RF RXD
(I/O)
memory
EXT TRIG
From EXT BP
RO-XY converter
External Radar EXT HD
Echo FPGA
MAIN CPU
DVI driver
Display - Coler palette
Main CONT priority Display color
- Brilliance
Closs cursor
DVI driver
Closs cursor processing
Graphic data
data
processing
DRW CPU
Graphic data
Graphic data
processing
memory
Graphic data
108MHz Dot
ADD. GEN
CLK
DRW FPGA
7-33
7.3 Processor Unit: RPU-013
Note:
Since the saving of FPGA is transferred to U48 on and after the SPU board Ver-22,
U6, U15 and U54 are eliminated.
7-34
7.3 Processor Unit: RPU-013
RPU-013
SPU p.c.b
AD/DATA OP HD OUT-1
ARPA/MAIN CPU HD
U30
SPU FPGA
OP HD OUT-2
OP BP OUT-1
BP
U46
J617, J618
U41
OP BP OUT-2
RF Tx/Rx SUB Display-1, 2
RFC p.c.b OP TRIG OUT-1
TRIG
U40
OP TRIG OUT-2
Echo data
8bit
SEL VIDEO SEL A/D
(U83) (U76)
HD IN
TEST ECHO BP IN
RF unit TRIG IN J616
FULL LOG OUT
Master Radar
SEMI LOG VIDEO TP58 R401
OP VIDEO IN U85 OP VIDEO IN
GAIN/STC CONT
The level of video signal from external radar can be adjusted by R401 so that the video
signal level of TP58 becomes 2.0 Vp-p.
See page.4-74 to 4-82 for information on connection of video signals to and from
external devices.
7-35
7.3 Processor Unit: RPU-013
3. Structure of screen
The order of presentation of screen is as follows:
1. Color-filled chart, plotter
2. Radar echo, echo trail
3. Radar mark
4. ARPA, AIS
5. Characters: Menu, icon display, cross-cursor
The mask screen controlling the display area of the screen in [Menu] -> 1 -> 7:ECHO
AREA masks the screens 1 through 4 in Fig.7.3.8.
2
12 HDG 210 T
GAIN SPD 10.1Kt
STC
HEAD FTC COG 210 T
3 SOG 10.1Kt
MENU
7-36
7.3 Processor Unit: RPU-013
RFC p.c.b
STC DETECT
STC STC CONT IF p.c.b
SPU p.c.b
AD CON
Setting parameter
- MODEL
- STC RANGE FTC(RAIN)
- SEA CONDITION
- ANT HIGHT
- NEAR/MID/FAR STC CARV
Heading data
Speed data(BT/WT)
ARPA
QV
SEL
NOISE REJ
INT REJECT
VIDEO CONTRAST
ECHO STRETCH
ECHO AVERAGE
WIPPER
Heading/Speed data
or
Own Pos. data
Heading/Speed data
or
Own Pos. data
TRAIL
ZOOM
presentation
7-37
7.3 Processor Unit: RPU-013
- Trail copy
Turn on the setting of Trail Restart (linked with trail rage) and Trail Copy. If the
range change is 3 to 1/3 times relative to the range where the trail is started, all
trails can be displayed promptly. This is because the trail of the previous range is
copied.
Changing Range
Trail Copy
When about 10 seconds or more elapses after the range change, the trailing at the
range starts following the copy of the previous trail. If the range is changed to a
range exceeding 3 to 1/3 times the previous range, a new trailing process starts. If
the range is changed to move than 3 times the previous range, the range up to 3
times the previous range is saved. For the range exceeding 3 times or less than 1/3
times, a new trailing process starts. However, if it is returned to the previous range
within 10 seconds, the saved previous trail is displayed.
7-38
7.3 Processor Unit: RPU-013
- Narrow trail
When the setting of Narrow Trail is turned on, a trail width is presented in one dot.
The narrow trail can be used when selecting the long trial time. This feature is not
available on the IMO and A type radars. The narrow trail is processed for relatively
strong and large echoes, the level of which is 8 to 32 and the signal on screen is 6
dots in azimuth direction and 3 dots in rage direction.
The narrow trail processing can be used for a echo which is in level 8 or higher for
echo level divided into 32 and has a size of 6 dots in a row in the bearing direction
and 3 dots in a row in the distance direction on the screen coordinates. To be more
specific, the narrow trail processing is not done for smaller echoes
7-39
7.3 Processor Unit: RPU-013
- WIPER-1
The input signal is computed using the wiper coefficient K and the signal level is
gradually reduced. The smaller is the signal level, the smaller the wiper coefficient
is. Consequently, weaker signals disappear quicker than stronger signals.
Time
Signal Level:S
n+1 1
2 1
S x K1=S1
3
2
S1 x K2=S2
4 1.0
3
K
S2x K3=S3
0
4 Signal Level
n+1
- WIPER-2
The processing of WIPER-2 operates basically in the same way as for WIPER-1
processing. However, wiper processing and EAV is performed in parallel and the
wiper processing is performed so that final echoes level is same level as EAV only
is used. For instance, if the echo level is set as medium level input in the EAV-2
setting and they are continuous echoes, the wiper-processed echo of the final block
is emphasized more than the previous echo.
7-40
7.3 Processor Unit: RPU-013
3. Zoom
Zoom magnification can be selected in the setting of 4:ZOOM (OFF/2 TIMES/3
TIMES) of [Menu] -> 9 -> 2:DATA BOX menu.
For zoom processing, select “ZOOM” in the [CURSOR] menu. Place the cursor on the
picture to be zoomed and click the left button. The zoomed picture is displayed in the
data presentation area on the right of the screen. The picture in the normal picture
presentation area has a dotted frame showing a zoomed area.
- IR-1: Correlation between the current sweep and last one sweep
- IR-2: Correlation between the current sweep and last two sweeps
- IR-3: Correlation between the current sweep and last three sweeps
For instance, in IR-3 setting, when the same echo is present Output echo
7-41
7.3 Processor Unit: RPU-013
ES1
ES2
7-42
7.3 Processor Unit: RPU-013
ES3
- EAV-1
Used for displaying target signals by distinguishing them from unwanted signals of
sea clutter, rain and others.
- EAV-2
Used for displaying target signals by distinguishing them from pictures of strong
sea clutter, rain and others. With its strong force to suppress the signal strength of
sea clutter, rain and others, it has a strong control force and may suppress weak
target signals. EAV-2 and EAV-1 should be selectively used depending on the
strength of unwanted signals.
- EAV-3
Used for displaying a target in highlight.
Since this feature allows displaying a weaker target by increasing its intensity, it is
used for enhancing the sensitivity particularly of a target in a long distance. Since
unwanted signals of sea clutter, rain and others are also emphasized, video
adjustment is required to remove unwanted signals.
7-43
7.3 Processor Unit: RPU-013
EAV OFF
EAV1
EAV2 EAV3
7-44
7.3 Processor Unit: RPU-013
The figures below show input signals and EAV output level in a simplified way.
Although there are 32 signal levels, they are shown in 0 to 7 levels in the figures.
EAV-1 EAV-2
n n+1 n+2 n+3 Scan n n+1 n+2 n+3 Scan
7(32) 7(32)
7(Max.) 32 level 6 6
Signal Level
Input
Signal Level
5 5
6 4
4 Output
3 3
5
2 2
4 1 1
0 0
3
2 Input-1 Input-1
0 0 7 7 7 7 7 7 7 0 0 0 0 0 0 0 0 7 7 7 7 7 7 7 0 0 0 0 0 0
1
EAV out-1 EAV out-1
0(Min.) 0 0 0 0 1 4 7 7 7 7 4 3 2 1 0 0 0 0 0 1 2 4 7 7 7 4 3 2 1 0 0
Signal Level
6
Signal Level
5 5
4 4
3 3
2 2
1 1
0 0
Input-2 Input-2
0 0 4 4 4 4 4 4 4 0 0 0 0 0 0 0 0 4 4 4 4 4 4 4 0 0 0 0 0 0
6
Signal Level
5 5
4 4
3 3
2 2
1 1
0 0
Input-3 Input-3
0 0 7 0 6 7 0 6 7 6 0 0 0 0 0 0 0 7 0 6 0 0 0 0 0 0
7 6 7 6
EAV out-3 EAV out-3
0 0 0 0 0 1 0 0 1 3 2 1 0 0 0 0 0 0 0 0 1 0 0 1 2 1 0 0 0 0
- Input-1
Shows the EAV output when the strongest signals are inputted in a row
- Input-2
Shows the EAV output when signals of medium intensity are inputted in a row.
EAV outputs become increasingly larger than inputted signals and a little
higher than the input level
- Input-3
Shows the EAV output when there is no signal input in a row. The EAV output
level is not so much increased.
7-45
7.3 Processor Unit: RPU-013
The figures below show input signals of EAV-3 and EAV output level in a simplified
way. Although there are 32 signal levels, they are shown in 0 to 7 levels in the figures
below.
EAV-3
n n+1 n+2 n+3 Scan
7(32)
7(Max.) 32 level 6
Signal Level
5
6
4
5 3
2
4 1
0
3
2 Input-1
0 0 7 7 7 7 7 7 7 0 0 0 0 0 0
1
EAV out-1
0(Min.) 0
0 0 7 7 7 7 7 7 7 6 5 4 3 2 1 0
7(32)
6
Signal Level
5
4
3
2
1
0
Input-2
0 0 4 4 4 4 4 4 4 0 0 0 0 0 0
EAV out-2
0 0 4 5 6 7 7 7 7 6 5 4 3 2 1 0
5
4
3
2
1
0
Input-3
0 0 7 0 6 7 0 0 5 7 6 0 0 0 0
EAV out-3
0 0 7 6 6 7 6 5 5 7 7- 6 5 4 3 2 1 0
7-46
7.3 Processor Unit: RPU-013
- Input-1
Shows EAV outputs when the strongest signals are inputted in a row.
- Input-2
Shows EAV outputs when signals of the medium level are inputted in a row.
The EAV outputs become increasingly larger than inputted signals and finally
reach the highest level.
- Input-3
Shows EAV outputs when no signal is inputted in a row. EAV outputs serve to
maintain the input level and outputs are gradually reduced as signals become
less.
Input Signal
Input Signal
CLK 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Output Signal
Clock
Short/Middle Pulse: 80MHz
+ Output Signal
Long Pulse: 40MHz Average Noise Rej. OFF Noise Rej. ON
In long pulses, for instance, it is possible to receive echoes close to the pulse-length at
1.2 µ sec pulse. The shift lock frequency of the delay circuit is 40 MHz/25 nsec. Since
the delay circuit is comprised of 16 stages, the delay time is 16 x 25 nsec = 0.4 µ sec.
Consequently, there is a delay of 1.2 µ sec pulse + 0.4 µ sec since an echo of 1.2
µ sec pulse length is inputted into the delay circuit until the echo is completely
outputted, to make the echo a little extended. In the short and middle pulses, shift lock
frequency is set at 80 MHz since the pulse length is smaller. The pulse length in S1, for
instance, is 0.07 µ sec.
7-47
7.3 Processor Unit: RPU-013
A C
D
- STC
Processing
1
Range 2
Moving average
deviations xK
B
Target echo
Rain/snow echo
A
FTC setting
FTC effect
4
3
B C=A-B 2
1
OFF
C
FTC VR
(A/C RAIN VR)
D STC
The input signal A is subjected to the processing of moving average deviation. In this
processing, the range of the distance to be extracted is deviated in one sweep and signal
levels of respective distances extracted are averaged.
Averaged signals are multiplied by the coefficient K determined by the FTC setting. The
signal B is subtracted from the input signal A to create the signal C. The signal C is
STC-processed (curve of 1/Square of distance) and outputted. The FTC control knob is
used for adjusting the STC level. The effect of FTC is larger as the FTC setting value is
larger and as FTC VR is turned clockwise.
Rang
n Sweep -----
-----
-----
~ -----
-----
~
+ Moving average
deviation Output
7-48
7.3 Processor Unit: RPU-013
Picture Level
C
B
A
0 0
5dB
7dB
9dB
11dB
Fig. 7.3.19 Change width of picture level and change width curve
Setting of change width of picture level: In the setting of 1/2/3/4, if it is set to”2”, the
change width is 9 dB in the picture levels of 32. If the setting is “4”, the change
becomes steep with the change width of 5 dB. The change width curve “B” shows a
linear change. In case of the change width “C”, changes become smaller as the picture
levels become higher.
7-49
7.3 Processor Unit: RPU-013
A-1 A-4
B-1 B-4
C-1 C-4
7-50
7.3 Processor Unit: RPU-013
Picture-1
- Range: 6NM
- IR: 2
- ES: OFF
- EAV: OFF
- STC: MAN (50)
- RAIN: MAN (50)
- Auto RAIN: OFF
- Video contrast: 2/B
- Pulse: M2
- Sea condition: 2
Picture-2
- Range: 6NM
- IR: 2
- ES: 2
- EAV: 1
- STC: MAN (50)
- RAIN: MAN (50)
- Auto RAIN: OFF
- Video contrast: 3/B
- Pulse: M3
- Sea condition: 2
7-51
7.3 Processor Unit: RPU-013
Picture-3
- Range: 6NM
- IR: 2
- ES: OFF
- EAV: 2
- RAIN: MAN (50)
- Auto STC (54)
- Auto RAIN: OFF
- Video contrast: 2/B
- Pulse: M2
- Sea condition: 3
Picture-4
- Range: 6NM
- IR: 2
- ES: OFF
- EAV: OFF
- STC: MAN (50)
- RAIN: MAN (50)
- Auto RAIN: 2
- Video contrast: 2/A
- Pulse: M2
- Sea condition: 2
7-52
7.3 Processor Unit: RPU-013
NEAR
- Range: 6NM
- IR: 2
- ES: OFF
- EAV: OFF
- STC: MAN (50)
- RAIN: MAN (50)
- Auto RAIN: OFF
- Video contrast: 3/B
- Pulse: M2
- Sea condition: 2
SHIP
FAR
- Range: 6NM
- IR: 2
- ES: 2
- EAV: 3
- RAIN: MAN (50)
- Auto STC: ON (54)
- Auto RAIN: OFF
- Video contrast: 3/C
- Pulse: L
- Sea condition: 3
7-53
7.3 Processor Unit: RPU-013
NEAR BUOY
- Range: 6NM
- IR: 2
- ES: 1
- EAV: 1
- STC: MAN (50)
- RAIN: MAN (50)
- Auto RAIN: OFF
- Video contrast: 3/B
- Pulse: L
- Sea condition: 2
FAR BUOY
- Range: 6NM
- IR: 2
- ES: 2
- EAV: 3
- RAIN: MAN (50)
- Auto RAIN: OFF
- Auto STC (64)
- Video contrast: 3/C
- Pulse: L
- Sea condition: 2
7-54
7.3 Processor Unit: RPU-013
ROUGH SEA
- Range: 6NM
- IR: 2
- ES: OFF
- EAV: 2
- RAIN: MAN (50)
- Auto RAIN: OFF
- Auto STC (54)
- Video contrast: 2/A
- Pulse: M2
- Sea condition: 4
SHIP
- Range: 6NM
- IR: 2
- ES: 2
- EAV: OFF
- STC: MAN (50)
- RAIN: MAN (50)
- Auto RAIN: OFF
- Video contrast: 3/C
- Pulse: M3
- Sea condition: 2
7-55
7.3 Processor Unit: RPU-013
HARBOR
- Range: 6NM
- IR: 2
- ES: OFF
- EAV: OFF
- STC: MAN (50)
- RAIN: MAN (50)
- Auto RAIN: OFF
- Video contrast: 3/B
- Pulse: M3
- Sea condition: 2
COAST
- Range: 6NM
- IR: 2
- ES: OFF
- EAV: OFF
- STC: MAN (50)
- RAIN: MAN (50)
- Auto RAIN: OFF
- Video contrast: 3/B
- Pulse: M3
- Sea condition: 2
7-56
7.3 Processor Unit: RPU-013
5-2. FAR-2837S
Noise REJ.:All OFF
Picture-1
- Range: 6NM
- IR: 2
- ES: OFF
- EAV: OFF
- STC: MAN (50)
- RAIN: MAN (50)
- Auto RAIN: OFF
- Video contrast: 2/B
- Pulse: M2
- Sea condition: 2
Picture-2
- Range: 6NM
- IR: 2
- ES: 2
- EAV: 1
- STC: MAN (50)
- RAIN: MAN (50)
- Auto RAIN: OFF
- Video contrast: 2/A
- Pulse: M3
- Sea condition: 2
7-57
7.3 Processor Unit: RPU-013
Picture-3
- Range: 6NM
- IR: 2
- ES: OFF
- EAV: 2
- RAIN: MAN (50)
- Auto STC (54)
- Auto RAIN: OFF
- Video contrast: 2/B
- Pulse: M2
- Sea condition: 3
Picture-4
- Range: 6NM
- IR: 2
- ES: OFF
- EAV: OFF
- STC: MAN (50)
- RAIN: MAN (50)
- Auto RAIN: 2
- Video contrast: 2/A
- Pulse: M2
- Sea condition: 2
7-58
7.3 Processor Unit: RPU-013
NEAR
- Range: 6NM
- IR: 2
- ES: OFF
- EAV: OFF
- STC: MAN (50)
- RAIN: MAN (50)
- Auto RAIN: OFF
- Video contrast: 3/B
- Pulse: M2
- Sea condition: 2
FAR
- Range: 6NM
- IR: 2
- ES: 2
- EAV: 3
- RAIN: MAN (50)
- Auto STC: ON (54)
- Auto RAIN: OFF
- Video contrast: 3/C
- Pulse: L
- Sea condition: 3
7-59
7.3 Processor Unit: RPU-013
NEAR BUOY
- Range: 6NM
- IR: 2
- ES: 1
- EAV: 1
- STC: MAN (50)
- RAIN: MAN (50)
- Auto RAIN: OFF
- Video contrast: 3/B
- Pulse: L
- Sea condition: 2
FAR BUOY
- Range: 6NM
- IR: 2
- ES: 2
- EAV: 3
- RAIN: MAN (50)
- Auto RAIN: OFF
- Auto STC (64)
- Video contrast: 3/C
- Pulse: L
- Sea condition: 2
7-60
7.3 Processor Unit: RPU-013
ROUGH SEA
- Range: 6NM
- IR: 2
- ES: OFF
- EAV: 2
- RAIN: MAN (50)
- Auto RAIN: OFF
- Auto STC (54)
- Video contrast: 2/A
- Pulse: M2
- Sea condition: 4
SHIP
- Range: 6NM
- IR: 2
- ES: 2
- EAV: OFF
- STC: MAN (50)
- RAIN: MAN (50)
- Auto RAIN: OFF
- Video contrast: 3/C
- Pulse: M3
- Sea condition: 2
7-61
7.3 Processor Unit: RPU-013
HARBOR
- Range: 6NM
- IR: 2
- ES: OFF
- EAV: OFF
- STC: MAN (50)
- RAIN: MAN (50)
- Auto RAIN: 2
- Video contrast: 3/B
- Pulse: M3
- Sea condition: 2
COAST
- Range: 6NM
- IR: 2
- ES: OFF
- EAV: OFF
- STC: MAN (50)
- RAIN: MAN (50)
- Auto RAIN: OFF
- Video contrast: 3/B
- Pulse: M3
- Sea condition: 2
7-62
7.3 Processor Unit: RPU-013
Operating
Protection Output line Remarks
current
+24 VDC TX-HV 5 to 7 A With delay of 0.1 s
Output short-circuit +24 VDC ANT
4 to 5 A With delay of 0.1 s
protection operating power supply
current 2.8 A or more: Turned of with a
ANT motor line 2.8/6.4 A
delay of 2 to 3.5 s
Output over current +12 VDC 5.5 A
protection operating -12 VDC 0.54 A
current +5 VDC 8.5 A
7-63
2. Block diagram of power board
U63
CUR PR4
R196-198
J108 +24V HV
100VAC:Short J103
220VAC:Open U62 CUR PR3
TP6/7 TP13
J181 CR26 C26/27
Dubler ON/OFF +24V R191-194 +24V
CR71, J105-9,10
100-220VAC L1 R40/124 L31/32 C77/78
-24V RT191
K1 C31/32 REC FAN 24V
Line FIL T2/3, J106
REC Q31-34
Q23 U31/32 TP12 U191: -12V -12V
L33/34 CR72/73, -14V uPC79N12H J104-15,15
PR12_A C79 -12V AVR
SW Reg. REC TP16
TP5
TP11
K1, Q21/1819/22 PR5V _C SW CONT +5V
CR1, C5 CR74, +12V UI131/132 CR133,
REC Triac, K1 Cont. C80 Q131/132 L132,C142 J104-6,7
REC SW Reg. REC
PWR ON2 PWR ON1
CUR PR1 +6.5V +12V
J105-8
CR7, C13 E1/2 +12V
R81 R88 J104-8,9
REC TP1 U21:RC9501 U25 +12V ADJ.
T1,Q1/2, +6.5V 2NINV SW Cont. U81 U23 Q141
CR5,C8,U1
CR2/3/4 PR12_A POWER FAIL
REC/AVR R48
ININV J104-1
SW Reg. TP3 45kHz ADJ.
100VAC:Short (Self OSC) CR6,C11/12,L2 +12V
PR12_A
220VAC:Open REC
Q13/14 Q41/42
J108
7-64
U11:RC9520 U12 DT Cont.
Soft start
Input Volt TP8/9 U24
Hi/Low DET. PR12_A
T4/5,U51/52
R21 Q51-54 TP14 TP19
RCU-014 PWR ON1 L51/52 CR101 Q181, CR181,L181,
Over VLT ADJ L53/54 +32V MOTOR
RCU-015 C51/52 C103/104 Q163-167 C183 J105-1,2
+6.5V SW Reg. REC
J105-7 REC REC
SW Reg. R88
PSW_H SW CONT R106 MON MOTOR VLT
- Q151,CR161
U4 U2 Q4 Q3 +32V SW CONT J104-2
+ CUR PR2 AVR
U112 R105 ADJ. E1/2
E1/2
Window +12V
U3 U161:MB3759PF
Comparator
- U22:RC9501 U27 SW Cont.
+ SW Cont. IN1
PR12_A 2NINV +6.5V IN2 TP17
U13 Q16 Q17 ININV U26 BP
Q43/44 U162:MB4206PF J105-5
POWER SW PR12_A ANT SPEED
DT Cont. F-V Converter J104-4
Soft start
CR23 JP161
PWR ON2
R168
CR4/62, U112
Q61/62/63/65 U61
PR12_A U151: R168:ANT Rotation
Over Current +6.5V Q153,C157
JP162
power
U63
CUR PR4
R196-198 +24V HV
J103
U62 CUR PR3
TP6/7 TP13
J181 +24V R191-194 +24V
CR71, J105-9,10
L31-33 C77/78
24VDC -24V RT191
C31-36 REC FAN 24V
T2/3, J106
Line FIL Q31-34
U31/32 TP12 U191: -12V -12V
L33/34 CR72/73, -14V uPC79N12H J104-15,15
PR12_A C79 -12V AVR
REC TP16
SW Reg.
TP11
SW CONT +5V
CR1, C5 CR74, +12V UI131/132 CR133,
REC C80 Q131/132 L132,C142 J104-6,7
REC SW Reg. REC
CUR PR1 +6.5V +12V
J105-8
E1/2 +12V
R81 R88 J104-8,9
TP1 U21:RC9501 +12V ADJ.
U25
T1,Q1/2, +6.5V 2NINV SW Cont. U81 U23 Q141
CR5,C8,U1
CR2/3/4 PR12_A POWER FAIL
REC/AVR R48
ININV J104-1
SW Reg. TP3 45kHz ADJ.
(Self OSC) CR6,C11/12,L2 +12V
PR12_A
REC
Q21/22
DT Cont.
7-65
Soft start TP8/9 U24
PR12_A
T4/5,U51/52
RCU-014 Q51-54 TP14 TP19
L51/52 L53/54 CR101 Q181, CR181,L181,
C103/104 +32V Q163-167 C183 MOTOR
RCU-015 C51/52 J105-1,2
+6.5V SW Reg. REC
J105-7 REC REC
SW Reg. R88
PSW_H SW CONT R106 MON MOTOR VLT
JP1 Q151,CR161
- +32V SW CONT J104-2
+ U4 CUR PR2 AVR
U3 ADJ.
Q23/24 U112 R105 E1/2
E1/2
Window DT Cont. +12V
U3 U11:RC9528 U161:MB3759PF
Comparator Soft start
- INPUT Low/Hi U22:RC9501 U27 SW Cont.
+ Volt DET. SW Cont.
CR23 IN1
2NINV +6.5V IN2 TP17
U2 U26
ININV BP
Q4 Q3 U162:MB4206PF J105-5
POWER SW PR12_A ANT SPEED
F-V Converter J104-4
JP161
R168
CR4/62, U112
Q61/62/63/65 U61
PR12_A U151: R168:ANT Rotation
Over Current +6.5V Q153,C157
JP162
Power-ON
1. Generating control voltage for power supply circuit
AC power supply inputs are rectified at CR1 and C5 and generates power supply of
+12 VDC, +6.5 VDC and +5 VDC for the power supply control circuits on the
power supply circuit of a self-excited oscillation type comprised of Q1, Q2 T1 and
CR2 to 4.
7-66
7.3 Processor Unit: RPU-013
ANT Motor
+24VDC 42rpm
MAIN CPU
ANT ON J610
BP ANT SPEED ANT +20VDC 36rpm
REG
Control (ANT Motor)
BP
U21
SPU-013 PWR
RPU-013
7-67
7.3 Processor Unit: RPU-013
SPU board
DVI-D
J104- Vcc DVI-D
#4/5/6(+5V) MONITOR
PWR board (MU-201CR)
J201- J204-#14(+5V) (MU-231CR)
#4/5/6(+5V)
DVI-D
7-68
7.3 Processor Unit: RPU-013
T1 500V
REC
(CR11) J482
300V
MAIN INV TP3 TP1 SUB INB TP4
J481 JP2 1. Tx-HV
SW (45kHz) (+35V) SW (45kHz) 330V 500V JP1
1. +24V (Q1:2SK1420) (Q2:2SK1432)
300V REC 300V
REC
2. -24V (CR3) 260V (CR12) 2. GND
160V
-24V
160V
-10V
-24V
CONT.
CONT.
VR1 0
E1
+24V
-10V
RT CT DT OC CR23
R2/3 C7
CR6 C7
TP2 -24V
(RD10EB1) CR1
-10V
The TX-HV board is comprised of a main inverter and sub inverter. Each inverter is
controlled by U1 and the switching frequency is about 45 kHz and determined by R2, 3
and C7. U1 incorporates the IC for pulse length control of MB3757 with its peripheral
circuitry molded.
CR23 lights up when the power is supplied to this board and CR21 lights up when over
current of about 0.7 A is detected on the TX-HV. VR1 should be adjusted so that the
output voltage of the main inverter of TP-1 is 35 VDC. TX-HV voltage is set at JP1 and
JP2. The voltage setting is 310 to 350 VDC in case of a 10 kW –radar (FAR-2x17) and
520 to 580 VDC incase of radar of 25 kW or more (FAR-2x27).
7-69
7.3 Processor Unit: RPU-013
CR2 CR1
(DATA) (LINK)
J302
J207 U3
25MHz 1. Tx P
Tx data 2. Tx N
U1 LAN
ADD. / DATA LAN I/F Rx data 3. Rx P
6. Rx N
U2
EEPROM
The LAN cable between FAR-2xx7 radars, and between FAR-2xx7 and CU-200 is a
cross cable. When HUB-100 is used for the connection, either a straight cable or cross
cable can be used. All the ports of HUB-100 are provided with Auto-MDIX feature and
automatically recognize cable types.
SPU p.c.b
LAN
100Base-Tx NET-100
8 ports
SPU p.c.b No.x FAR-2xx7
LAN 100Base-Tx LAN 100Base-Tx
NET-100 HUB-100
cross cable cross cable
CARD CPUp.c.b
or or
No.x FAR-xx7 straight cable
straight cable NET-100
LAN
CU-200
7-70
7.4 Control Unit
For connection between units, connect the [PROCESSOR] side with a higher-level unit.
The interface is RS-422 based on asynchronous communication method (19,200 bps).
Alarm sounds and panel brilliance data are outputted from RPU-013 to the control unit,
and key and control knob information and track ball data re outputted from the control
unit to RPU-013. The cable length from RPU-013 to the last control unit is 31 m at
longest taking supply voltage drop into consideration.
TB p.c.b
7-71
7.4 Control Unit
The figure below is the block diagram of connection of RCU-013 and RCU-014. See
page.4-58 for information of System Fail.
RPU-013
RCU-014
PROCESSOR REMOTE
SPU KEY U6 U6
p.c.b J501 (RS422 I/F) (RS422 I/F) J502
RS422 I/F J602
SN751178NS
SN751178NS
KEY TXD H/C TD UP H/C TD DN H/C
1, 2 1, 2 TX/RX 0 TX/RX 1 1, 2
SN751178NS
PROCESSOR
KEY RXD H/C RD UP H/C RD DN H/C
3, 4 3, 4 3, 4
PWR SW
PWR 5 5 S36
5
p.c.b GND (DIP SW) GND
6, 8 6, 8 POWER SW 6, 8 RCU-016
12V 12V IN 12V IN
U21 TERMINAL U8
7 7 7
MAIN CPU p.c.b CPU
U9
BZ REMOTE
SYS FAIL H SYS FAIL H
9 9 4 SOUND
9
1
SYS FAIL N
SYS FAIL C SYS FAIL C
10 10 10
3 2
U12
(PS7241 1B)
J622 RADAR OK
SYS FAIL H
1 1 1
GND SYS FAIL C GND
2 2 2
U14 J506
KEY
SYS ACK N
11 SYS ACK H KEY & EMRI
3 ILLUMI
12 GND
EXT ALARM ACK N 4
9
1 J507 Rotary
Encoder
ALARM 1 ALARM 2
to SYSTEM FAIL
ALARM 3 OPERATOR FITNESS 8
J612
EXT ALARM
7-72
7.5 Monitor Unit
MU-201CR MU-231CR
Remarks
(20. inches) (23.1 inches)
The number of output dots
Output signal differs according to the
1024 x 1280 dots 1024 x 1360 dots
from RPU-013 setting of S1 of the SPU
board.
Monitor display
1024 x 1280 dots 1200 x 1600 dots
process dots
Dots in radar
496 dots 496 dots
effective radius
Radar effective
308 mm 340 mm
radius
SPU board
OFF/OFF ON/OFF
S1-#1/2
7-73
7.5 Monitor Unit
LCD panal
NL128102AC31-02
Power ON +5V
F1: 2A
+12V
100-240VAC +24V AC/DC power
FL1 RC+
(FL-205A) (RKW12-13RE) RC-
Ship’s Main
Inverter Board
TB1
LCD panal
NL128102AC31-02
F1: 5A
+12V
24VDC +24V DC/DC Board
FL1 RC+
(MXB-1206-33) (03P9359) RC-
Ship’s Main
TB1 Inverter Board
7-74
7.5 Monitor Unit
2. MU-231CR
The power-on signal of the monitor unit is inputted into the DVI I/F board as signals of
#14 pin (+5 V POWER) of the DVI connecter. The DVI I/F board outputs DDC +5 V
signals based on these signals to control ON/OFF of the power supply unit and outputs
“RC+/-” signals via the filter board. The DVI I/F board also converts SXGA signals into
UXGA signals.
LCD panal
DVI I/F Board
(BSM501FN1) FLC59UXC8V-04
Power ON +5V
DVI LCD I/F Board
(SXGA)
+12V
F1: 2A
DDC+5V
VVR
VCNT
100-240VAC +24V AC/DC power
FL1
(LF 205A) (RKW12-13RE-P)
Ship’s Main +12V
TB1 Inverter Board
RC+
RC-
Filter Board
FAN (03P9360)
LCD panal
DVI I/F Board
(BSM501FN1) FLC59UXC8V-04
DVI SXGA -->
LVDS UXGA
Power ON +5V
Data/CLOCK
Power ON +5V
+12V
F1: 6A
DDC+5V
VVR
24VDC +24V DC/DC Board VCNT
FL1
(MXB-1206-33) (03P9359)
Ship’s Main +12V
TB1 Inverter Board
RC+
RC-
Filter Board
FAN (03P9360)
7-75
7.5 Monitor Unit
MU-201CR MU-231CR
Model MU-120C MC-155C MU-151C MU-201C
(Standard) (Standard)
Connection
Yes Yes Electrically connectable No Yes
with FAR
Picture size
20.1 23.1 12.1 15 15 20.1
(inch)
Monitor 1024 x 1280 1200 x 1600 800 x 600 1024 x 768 1024 x 768 1024 x 1280
resolution (SGXA) (UXGA) (SVGA) (XGA) (XGA) (SXGA)
- DVI-D
- RGB analog
- Mini D-SUB15 pin RGB analog
Input Mini D-SUB
DVI-D RGB analog Mini D-SUB
connector 15 pin
- RCA 15 pin
- DVI-D
NTSC/PAL
100-240
Power 100-240 VAC
12-24VDC VAC 100-240 VAC
supply /24 V
/24 VDC
SPU board
OFF/OFF ON/OFF OFF/ON OFF/ON
S1-#1/2
Note-1
Note-1, Note-2
Remaks Note-2
Note-3, Note-4
Note-3
Note-1
Set S1-#1/2 of the SPU board to OFF/ON. In this setting;
- Brilliance control signals included in DVI signals are not outputted.
- The [BRILL] icon bar is not displayed at the lower left of the screen.
Note-2
When connection with FAR is made by RGB analog signals, the connection should be
made by way of DVI I/F and RGB BUFF boards offered as option. See the
Installation Manual of FAR radar for the method of connection.
Note-3
For connection with the DVI-D connector, make connection directly. RCA signals are
not supported.
Note-4
Due to difference in monitor resolution, signals are omitted and this makes characters
illegible
7-76
Chapter 8. Q & QA& A
3. Which cable should be used for LAN CA, Cross CA or Straight CA?
See page.3, 7-70 and the Operator’s Manual of “HUB-100”.
Use a cross cable for connection between FAR and FAR, and FAR and CU-200.
For connection of FAR and CU-200 via HUB-100, either a cross cable or straight
cable of Category 5 can be used. The LAN cable kit FR-FTPC-10/20/30 m,
armored cable is available as option. All the ports of HUB-100 are provided with
the Auto-MDIX function, and automatically recognize a connecting cable.
Note:
Use a straight cable in case a hub is not provided with the Auto-MDIX.
SPU p.c.b
LAN
100Base-Tx NET-100
8 ports
SPU p.c.b
LAN 100Base-Tx LAN 100Base-Tx No.x FAR-2xx7 series
NET-100 HUB-100
cross cable cross cable
CARD CPUp.c.b
or or
straight cable straight cable NET-100
No.x FAR-xx7 series LAN
CU-200
8-1
Q&A
6. Can antenna cables for FR-1425 and FR-2120 be used for FAR-2127 and
FAR-2137S?
Cables for older types of radars RW-4873 (armored-cable RW-6895) can be used
with new-type IMO radar. There will be no problem if the cable length is 30 m or
less. Re-install wiring.
Note:
- Two cables of the older type are required for 24 V+/‐ power supply which
was not used for older types of radars.
- Although the new cable RW-9600 has fewer cores, it allows a larger current
capacity than the older types of cables (available only in 0.5 and 1.25 sq. mm
sizes) since the new cable size is a 1.5 or 2.5 sq. mm.
7. What types of the color LCD monitor can be used for connection?
See page.4-41 and 7-76.
Monitors compatible with SXGA are MU-120C, MU-155C, MU-200C, MU-201C
and. MU-120C and MU-155C are not compatible in terms of the display size.
For connecting with these monitors, make the setting of the DIP switch S1 on the
SPU board. Set “S1-#1” to OFF and “#2” to ON.
8. Can any number be assigned for the radar in the setting of [Menu] -> 0 -> 4 ->
4: RADAR NO.? See page.4-19.
Assign 1 to 4 to let the unit serve as Radar.
Assign 5 to 8 to let the unit serve as a sub monitor. Information on radars
connected to the LAN can be checked on the [ANT-X] box menu.
8-2
Q&A
10. What kinds of operations are allowed when switching to another radar
by the Inter-switch?
See page.4-21 and 4-23.
The setting of GAIN, STC and RANGE can be changed. Echo processing of ES,
EAV, Echo trail and etc. is performed on the switched side.
Operation such as ARPA acquisition and tracking is performed on the original
processor unit. The inter-switch can perform operations such as target acquisition,
vector mode/time, tracking interval and TCPA/CPA on the side of units.
12. Is there any specific order in the connection of RCU-014, 015 and 016.
See page.7-71.
Connect the processor unit (RPU-013) with RCU-014 or RCU-015. Since
RCU-016 does not have a power switch, it cannot be directly connected to
RCU-013. Connect RCU-016 to RCU-014 or RCU-015.
8-3
Q&A
15. Can the same ports be used for connecting a sub monitor?
See page.4-74.
There are two ports for connecting to the sub monitor, one for outputting semi-log
video signals and the other for full-log video signals. Select an appropriate port by
understanding the characteristics of each.
To use both ports for outputting same video signals semi-log or full-log, it is
required to modify the SPU board (03P9337).
To make the outputs of SUB DISPLAY-2 (SEMI-LOG: J618) same as the outputs
of SUB DISPLAY-1 (FULL-LOG: J617), follow the procedure below.
17. Which format should be used for HDG, AD format or NMEA format?
See page.4-42.
Either AD format or NMEA format can be used.
However, in case of AD format, input data to J608 on the TB board at the output
interval of 25 msec. In case of the NMEA format, input the HDT sentence to
J605 on the TB board at the speed of 38.4 kbps (IEC61162-2) and output interval
of 25 msec.
8-4
Q&A
19. Which chart card is read when 2 chart cards are inserted into CU-200?
- When two chart cards are inserted:
Priority is given to a card that includes Detailed Data of the chart and includes
the own ship position within the range of the chart.
- If both cards include Detailed Data of the chart, the card that was displayed
before updating is read.
Note:
- The FAR receives the chart data from CU-200 when the display is updated, for
example, the change of the range and others.
- Contents of Detailed Data: depth contour, place name, etc
20. Can the PSU-007 use commonly for different supply voltages?
See page.4-72.
As for the PSU-007, the supply voltages cannot use commonly. Four types of
the PSU-007 are available according to different types of gearboxes (antenna
motor). The models of thermal relays and their setting differ depending on the
motor power supply. The PSU-007 has a label showing a compatible gearbox on
its.
Power type PWR board (ANT: rpm) FIL board TX-HV board
03P9339A (24 rpm)
100 VAC
03P9339B (42 rpm) 12 kW: HV-9017A
03P9341
03P9339C (24 rpm) - FAR-2x17
220 VAC
03P9339D (42 rpm) 25/30 kW: HV-9017B
03P9338C (24 rpm) - FAR-2x27
24 VDC - FAR-2827W
03P9338D (42 rpm) - FAR-2x37S
03P9352 - FAR-2837SW
03P9338A (24 rpm)
12 VDC
03P9338B (42 rpm)
8-5
Q&A
25. When the power is restarted immediately after turning the power off,
the ST-BY status starts within 3 minutes.
When the power is restarted in a short while after turning it off, the Magnetron
has still been warmed up. In this case, 3 minutes delay time is not necessary,
resulting in shortened delay time. Since the delay time is determined by
detecting the voltage of the capacitor C304 on the SPU board, the delay time
varies depending on the detected voltage.
8-6
Q&A
27. When the [1:HL OFF] key is pressed, the range ring and all marks
disappear. Is this normal?
It is a normal procedure. When the [1: HL OFF] key is pressed, HD lines and all
marks except radar echoes disappear to see echoes.
8-7
Q&A
8-8
Q&A
2) Check that the data of [Menu] -> 0 -> 6 -> 8:TRACK PRESET is not changed
from the default. If the default setting is changed, execute [Menu] -> 0 -> 6 ->
0:DEFAULT to return the ARP preset setting to the default.
3) Check whether targets are displayed correctly in [Menu] -> 0 -> 6 -> 5:QV
DISPLAY. If QV echoes are weaker than actual echo, try changing the set of
[Menu]-> 0 -> 6 -> 4:ECHO LEVEL.
5) When the ship speed data is inputted by the GPS and a target is lost by changes
of ship speed, remove the ship speed signal from the log.
6) Try re-adjustments of the setting of [Menu] -> 0 -> 2 -> -2:CABLE ATT ADJ.
8-9
Q&A
40. The [BRILL] box menu is not displayed. And the brilliance cannot be
adjusted even by turning the BRILL control.
See page.4-41 and 7-73.
Check the setting of S1 of the SPU board. The setting of S1 is set to the “BB”
type.
41. The monitor size and picture size does not match each other.
See page.4-41 and 7-73.
Check the setting of S1 of the SPU board.
44. Can marks and lines created on GD-280 and GD-680 be used?
It is possible by converting GD-200/680 data into the GD-3000 format using the
conversion software “GD8891wim”. All data cannot be converted and some marks
may be presented by different shape.
8-10
Q&A
8-11
Q&A
50. Is it possible to make the setting of AIS static information and to send
AIS messages from the FAR?
See page.3-13.
It is possible in the setting of the [AIS] box menu.
- [AIS] -> 5 [TRANSMIT MESSAGE]
AIS messages created here are sent by AI ABM and BBM sentences to the
AIS unit and sent as AIS messages.
ABM:MSG 12, MSG 6 BBM:MSG 14, MSG 8
- [AIS] -> 6 [VOYAGE DATA]
Voyage information set from the FAR to set in the AIS unit using AI SSD, and
VSD sentences.
Voyage information set from the AIS unit also displays the information of AI
VDO sentences, except the information of “CREW”.
For instance, voyage information set in the AIS unit is outputted to the serial
port as AI VDO in about 5 seconds and displayed.
- [AIS] -> 7 [STATIC DATA]
The own ship information (static information) outputted by AI VDO
sentences from the AIS unit is displayed.
AI VDO sentences are sent every 6 minutes from the AIS unit or outputted
when data is changed. Wait 6 minutes to check updating.
51. What are the conditions for the loss of AIS targets?
It is presented when the lost target is detected on the radar side. These conditions
differ from conditions for the loss of a target on the AIS unit.
The conditions for a lost target on the FAR are;
- When the target cannot be received 5 times in the report intervals of the target
- When the target cannot be received for 6 minutes
Note:
- Conditions of the lost target on the FA-100 side are;
When the target cannot be received for 3 minutes 20 seconds or more, the
target becomes a lost target and when it is not received for another 3 minutes
20 seconds or more, it is deleted from the reception file.
8-12
Q&A
SOG Victor
& COG ROT
Heading
Sleeping Terget Lost Target Activated Target Target selected Dangerous Target
for data display
ARPA symbol
Automaticallty ACQ
Manually ACQ
flashing flashing
after acquistion
Initial stage Steady tracking CPA alarm CPA alarm ACK Lost Target
In 60 Scans, flashing
changes to Guard zone
1 R R On target passing
through operator-set
On selected target On reference target guard zone
53. How should the setting be made on radar side when the ECDIS is
connected?
See page.4-83.
Major settings are made in [Menu] -> 0 -> 8 -> 5:INS and [Menu] -> 0 -> 6 ->
2:TTM OUTPUT.
8-13
Q&A
58. What boards can be used commonly for X-band and S-band?
See page.5-2 and 6-37 to 6-39.
The list of boards is shown in page.6-37 to 6-39. The SPU board can be
commonly used. For boards of Ver-22 or later, the SPU FPGA program can be
updated from the PC as well as the main program. Programs of the SPU Ver-014
or later support this function.
8-14
Q&A
When TPYCY-2.5, for instance, is used a cable for power supply to the antenna
motor (220VAC/3 phase), the cable length that can contain the voltage drop
within 5% is:
62. Can SC-60/120/50/110 be connected with the IMO-type radar for heading
data?
It can be connected to a ship in a range between 300 GT to 500 GT. Since it is
mandatory for a ship of 500 GT or more to be equipped with a gyrocompass,
input the data from the gyrocompass. It is OK to connect SC-60/120/50/110 for a
backup purpose.
8-15
Q&A
63. The trackball of the control unit does not move smoothly.
When the outer ring of the trackball is turned to the left, the trackball can be
removed. Clean the trackball, inside the ring and roller of the trackball in the
same manner to clean the mouse of the PC.
Trackball
Roller of trackball
64. Proper menu setting is not known. How can the setting be reset to the
default?
See page.4-1.
Press the [2], [3] and [4] keys in order while holding down the [1:HL OFF] key
to call up FACTORY menu. Select “FACTORY DEFAULT” in this menu and
press the [ENT] key 5 times. Be sure to make the setting of the INITIALIZE
menu.
65. Although noise appears on the screen, echoes are not displayed.
See page.6-7.
Check TX high voltage, Magnetron heater voltage and Magnetron current in
[Menu] -> 9 -> 8 -> 2:SELF TEST. If the overcurrent is detected on the PWR
(RF) board due to a failure in the Magnetron, the pulse transformer or the MD
board, try checking by disconnecting the connector of MD board and TX high
voltage line.
8-16
Q&A
- Between Processor unit (SPU board) and control unit (CONT board):
RS-422/19.2 kbps
The ALERT BOX displays a KEY error. The program numbers of connected
keys, REMOTE 1 and REMOTE 2 are displayed as “******” in [Menu] ->
9 -> 8 -> 2:SELF TEST.
Note:
When the CPU of the CONT board of the control unit is operated, CR10
(RCU-015), CR11 (RCU-015 and 016) on the CONT board blink every
second.
8-17
Q&A
- LAN: 100BASE-Tx
When the communication is not enabled, restart all units connected to the LAN.
For the status of communication, check the LEDs on CU-200 and NET-100 of
RPU-013. CR-1 lights up when data is running over the LAN, and CR-2 blinks
when the unit is linked with the LAN. See page.6-24 for the layout of LEDs. For
another method for checking on the LAN communication, check [ANT] box menu
to see the communication between radars connected to the LAN. When [Menu] ->
6:CARD cannot be accessed, it means that communication is not being conducted
with CU-200.
Condition:
24 NM GAIN: 80, STC: 80
ES, EAV AUTO FTC: OFF
0V IR: 2
1.5 V Note:
The level changes according to adjustments
in [Menu] -> 0 -> 2 -> 2: Cable ATT ADJ.
8-18
Q&A
8-19
Q&A
2) Range resolution:
The distance R is determined by the pulse length: ( τ ).
R (m)=150 x τ
For instance, if the pulse length is 0.07 µ s for S1 pulse
R = 150 x 0.07
R = 10.5 m
3) Minimum range:
The pulse length ( τ ) determines the minimum range R.
R (m)=150 x τ
In the actual situation, the relation between the antenna height and vertical beam
width produce a shadow sector (target is not located within the vertical beam
width). This makes it impossible to detect targets at a close range. If the antenna
height is lowered to make the minimum detection range shorter, this makes the
maximum detection range shorter.
The minimum detection range can be calculated in the following equation:
Rmin = H / tan ( θ v/2)
where Antenna height (m) and vertical beam width ( θ v deg.).
Assuming that the antenna height is 30 m and the vertical beam width is 20
degrees (in case of the antenna XN-24AF)
Rmin = 30 / tan (20/2)
Rmin = 170.1 m
8-20
Q&A
4) Bearing resolution
It refers to the limit of the bearing angle in which approaching targets at the
same range can be separately displayed on the screen. This is dependent on the
directivity of the antenna (beam width). The beam width of the antenna
(XN-24AF) is 0.95 degrees.
The relation between the antenna effective length D (m) and beam width θ
(deg.) is expressed in the following equation:
θ (deg.) = 70 x λ (m)/D (m)
D (NM) = 2.23 ( h1 + h 2 )
Radar antenna height: h1 Target height: h2
Generally speaking,
there is a relation shown by this equation: A = G× λ 2/(4× π )
P × G 2 × λ2 × σ
S1=
(4 × π ) 3 × R 4
However, since there is a need to take composite waves created by direct waves
and sea-reflected waves into consideration in the equation of the radar wave
propagation over the sea, the actual value differs from the value obtained in the
equation above. The transmission output and antenna 3
area determines the detection range. For instance, when
TX output is doubled, the detection range is increased
2
by 1.19 times and the antenna area is doubled, the ANT
8-21
Q&A
7) False echoes
False echoes are echoes that appear on the screen at a position where there is no
target as if there is a target. The causes and characteristics of the false echoes are:
- Virtual image
A relatively large target close to your ship may be represented at two
positions on the screen. One of them is the true echo directly reflected by the
target and the other is a false echo which is caused by the mirror effect of a
large object on or close to your ship as shown in the figure below. If your
ship comes close to a large metal bridge, for example, such a false echo may
temporarily be seen on he screen.
- Multiple echoes:
Multiple echoes occur when a transmitted pulse returns from a solid object
like a large ship, bridge, or breakwater. A second, a third or more echoes
may be observed on the display at double, triple or other multiples of the
actual range of the target as shown below. Multiple reflection echoes can be
reduced and often removed by decreasing the gain (sensitivity) or properly
adjusting the A/C SEA control.
- Sidelobe echoes:
Every time the radar pulse is transmitted, some radiation escapes on each
side f the beam, called “sidelobes.” If a target exists where it can be detected
by the side lobes as well as the main lobe, the side echoes may be
represented on both sides of the true echo at the same range. Side lobes show
usually only on short ranges and from strong targets. They can be reduced
through careful reduction of the gain or proper adjustment of the A/C SEA
control.
- Shadow sectors
Funnels, stacks, masts, or derricks in the path of the antenna block the radar
beam. If the angle subtended at the antenna is more than a few degrees, a
non-detecting sector may be produced. Within this sector targets can not be
detected.
8-22
Q&A
Target
False echoes
8-23
Appendix 1) Sentences
AP1.1 Overview of NMEA-0183 Ver-3.00
1. Connection
Multiple LISTENER may be connected to single TALKER. The LISTENER receive
circuit shall consist of an opto-isolator and should have protective circuits to limit
current, reverse bias and power dissipation at the opto-diode as shown in Figure 1.1.1
The receive circuit shall be designed for operation with a minimum differential input
voltage of 2.0 Volts and shall not take more than 2.0 mA from the line at that voltage.
For reasons of the compatibility with equipment designed to earlier versions of this
standard, it is noted that the “idle, marking, logical “1”, OFF or stop bit state” had
previously been defined to be in the range –15 to +0.5 Volts. The “active, spacing,
logical “0”, ON or start bit state” was defined to be in the range +4.0 to +15 Volts while
sourcing not less than 15 mA.
2. Data configuration
Data is transmitted in serial asynchronous form in accordance with ANSI standards. The
first bit is a start bit and is followed by data bits, least-significant-bit first as illustrated
by Figure 1.1.2. The following parameters are used:
AP1-1
AP1.1 OVERVIEW of NMEA-0183 Ver-3.00
The following sentences are used: e.g) the DTM sentence is:
$ -- DTM , ccc , a , x.x , a , x.x , a , x.x , ccc *hh <CR><LF>
1) 2) 3) 4) 5)
1) “$” or “!” HEX 24 or HEX 21 – Start of sentence
2) <address field> TALKER identifier and sentence formatter
3) [“,”<data field>] Zero or more data fields
4) “*”<checksum field> Checksum field
5) <CR><LF> Hex 0D 0A – End of sentence
The first field shall be an address field containing the identity of the TALKER and the
sentence formatter which specifies the number of data fields in the sentence, the type of
data they contain and the order in which the data fields are transmitted. The remaining
portion of the sentence may contain zero or multiple data fields.
The maximum number of characters in a sentence shall be 82, consisting of a maximum
of 79 characters between the starting delimiter “$” or “!” and the terminating <CR>
<LF>.
A checksum field shall be transmitted in all sentences. The checksum field is the last
field in a sentence and follows the checksum delimiter character “*”.
The checksum is the 8-bit exclusive OR (no start or stop bits) of all characters in the
sentence, including “,” delimiters, between but not including the “$” and the “*”
delimiters. The hexadecimal value of the most significant and least significant 4 bits of
the result is converted to two ASCII characters (0-9, A-F (upper case)) for transmission.
The most significant character is transmitted first.
AP1-2
AP1.1 OVERVIEW of NMEA-0183 Ver-3.00
AP1-3
AP1.1 OVERVIEW of NMEA-0183 Ver-3.00
AP1-4
AP1.2 Configuration of NMEA Ver-3.00 Sentence
INPUT
1.2.1 ACK - Acknowledge Alarm
$--ACK , xxx *hh<CR><LF>
1
AP1-5
AP1.2 Configuration of NMEA Ver-3.00 Sentence
AP1-6
AP1.2 Configuration of NMEA Ver-3.00 Sentence
AP1-7
AP1.2 Configuration of NMEA Ver-3.00 Sentence
AP1-8
AP1.2 Configuration of NMEA Ver-3.00 Sentence
AP1-9
AP1.2 Configuration of NMEA Ver-3.00 Sentence
AP1-10
AP1.2 Configuration of NMEA Ver-3.00 Sentence
AP1-11
AP1.2 Configuration of NMEA Ver-3.00 Sentence
AP1-12
AP1.2 Configuration of NMEA Ver-3.00 Sentence
AP1-13
AP1.2 Configuration of NMEA Ver-3.00 Sentence
AP1-14
AP1.2 Configuration of NMEA Ver-3.00 Sentence
AP1-15
AP1.2 Configuration of NMEA Ver-3.00 Sentence
Output sentences
1.2.27 AAM - Waypoint arrival alarm
$--AAM , A , A , x.x , N , c—c *hh<CR><LF>
1 2 3 4 5
AP1-16
AP1.2 Configuration of NMEA Ver-3.00 Sentence
AP1-17
AP1.2 Configuration of NMEA Ver-3.00 Sentence
AP1-18
AP1.2 Configuration of NMEA Ver-3.00 Sentence
AP1-19
AP 1.3 Configuration of the Sentence from ARPA(FAR)
ARPA(FAR) to ECDIS(FEA.)
AP1-20
AP 1.3 Configuration of the Sentence from ARPA(FAR)
ARPA(FAR) to ECDIS(FEA.)
7 Antenna number
AP1-21
AP 1.3 Configuration of the Sentence from ARPA(FAR)
ARPA(FAR) to ECDIS(FEA.)
AP1-22
AP1.4 Configuration of the Sentence from ECDIS(FEA)
ECDIS(FEA) to ARPA(FAR.)
ARPA(FAR.)
AP1-23
AP1.4 Configuration of the Sentence from ECDIS(FEA)
ECDIS(FEA) to ARPA(FAR.)
ARPA(FAR.)
AP1-24
AP1.4 Configuration of the Sentence from ECDIS(FEA)
ECDIS(FEA) to ARPA(FAR.)
ARPA(FAR.)
AP1-25
AP1.4 Configuration of the Sentence from ECDIS(FEA)
ECDIS(FEA) to ARPA(FAR.)
ARPA(FAR.)
AP1-26
AP1.4 Configuration of the Sentence from ECDIS(FEA)
ECDIS(FEA) to ARPA(FAR.)
ARPA(FAR.)
AP1-27
Appendix 2) Specifications
Appendix 2) Specifications
1. ANTENNA RADIATORS
1. Type Slotted waveguide array
2. Beam width and sidelobe attenuation
X-band S-band
Radiator type
XN12AF XN20AF XN24AF SN30AF SN36AF
Length 4 ft 6.5 ft 8 ft 10 ft 12 ft
Beam width(H) 1.8° 1.23° 0.95° 2.3° 1.8°
Beam width(V) 20° 20° 20° 25° 25°
Sidelobe within ±10° -24 dB -28dB -28 dB -24 dB -24 dB
Sidelobe outside ±10° -30 dB -32 dB -32 dB -30 dB -30 dB
3. Polarization Horizontal
4. Rotation FAR-2117/2127/2827: 24 rpm or 42 rpm
FAR-2137S/2837S: 21/26 rpm or 45 rpm
FAR-2827W: 24 rpm
FAR-2837SW: 21/26 rpm
2. RF TRANSCEIVER
1. Frequency X-band: 9410 MHz ±30 MHz, S-band: 3050 MHz ±30 MHz
2. Output power FAR-2117/2817: 12 kW FAR-2127/2827/2827W: 25 kW
FAR-2137S/2837S/2837SW: 30 kW
Unwanted emissions comply with ITU-R RR.
3. Pulselength, PL, PRF and range
Pulselength S1 S2 M1 M2 M3 L
PL (µs) 0.07 0.15 0.3 0.5 0.7 1.2
PRF (Hz) 3000* 3000* 1500 1000 1000 600**
0.125, 6, 12, 24,
Range scale 0.5, 0.75, 0.75, 1.5, 3, 6, 12, 3, 6, 12,
0.25, 0.5, 48, 96,
(nm) 1.5, 3 3, 6 24 24
0.75, 1.5 120#
*: 2200 Hz with ARPA on, 32 nm range
**: 450 Hz on 96 and 120 nm ranges #: Non-IMO type only
4. IF 60 MHz
5. Noise figure 6 dB (typical)
6. Duplexer Ferrite circulator with diode limiter for
FAR-2117/2127/2137S/2817/2827/2837S
Ferrite circulator with TR limiter for FAR-2827W/2837SW
AP2-1
Appendix 2) Specifications
3. DISPLAY UNIT
1. Screen Yellow or green echoes in 32 levels. Rasterscan
non-interlace at 48.3kHz horizontal, 60 Hz vertical. Non-IMO
type has yellow or green monochrome plus 3-color display
according to echo strengths.
4. INTERFACE
1. IEC 61162-1 Ed. 2 RSD, TTM, AIS related data, etc.
2. Compass Built-in interface (option) for sync signal (20-135 V, 50-400
Hz), or stepper signal (20-135 VDC), any polarity, for
gyrocompass, GPS compass SC-60/120 by IEC 61162-2
3. Speed log NMEA format data
4. Others Echo sounder, GPS navigator, water temperature, etc.
AP2-2
Appendix 2) Specifications
5. POWER SUPPLY
1. Display unit 24 VDC or 115/230 VAC, 1ø, 50/60 Hz
FAR-21x7: 24 VDC, 2.3 A; 100-230 VAC, 0.7A (100 V)
FAR-28x7: 24 VDC, 3.2 A; 100-230 VAC, 0.9 A (100 V)
440 VAC, 1 ø, 50/60 Hz with optional transformer RU-1803
2. Processor unit FAR-2117/2817/2117-BB:
1 2 1 2
24VDC: 7.6A /8.5A , 100-115 VAC: 2.6A /3.0A ,
1 2
220-230 VAC: 1.6A /1.7A
FAR-2127/2827/2127-BB:
1 2 1 2
24 VDC: 8.8A /9.7A , 100-115 VAC: 3.0A /3.4A ,
1 2
220-230 VAC: 1.8A /1.9A
1: 2:
24 rpm, 42 rpm
3. Antenna unit (S-band) 200/220/380/440 VAC 115/230 VAC, 1ø, 50 or 60 Hz
4. Console 115/230 VAC, 1ø, 50/60 Hz, 440 VAC, 1ø, 50/60 Hz with
optional transformer RU-1803
6. ENVIRONMENTAL CONDITIONS
1. Ambient temperature (Complies with IEC 60945)
Indoor units -15°C to +55°C
Antenna unit -25°C to +55°C (storage +70°C)
2. Relative humidity 95% at 40°C
3. Waterproofing Antenna unit: IPX6 (IEC 60529)
Indoor units: IPX0 (IEC 60529)
4. EMC Full compliance with IEC 60945 Ed. 4
(to 2 GHz cabinet radiation)
AP2-3
Appendix 2) Specifications
7. OPTIONAL EQUIPMENT
SWITCHING HUB HUB-100
1. Access Format CSMA/CD
2. Switching Format Store and Forward
3. Transmission Speed Half-duplex: 10Mbps/100Mbps
Full-duplex: 20Mbps/200Mbps
4. Necessary Cabling 10BASE-T: Category 3 or higher STP cable
100 BASE-TX: Category 5 or higher STP cable
5. Max. Cable Length 100 m
6. Ports 8 ports
- All ports auto-MDIX compliant (straight or cross cable,
automatic recognition)
- All ports EMC compliant (STP cable port)
- All ports equipped with 3 LED injectors
(Link/Act, Full-duplex/Collision, 100Mbps/10Mbps)
7. Buffer Memory SRAM buffer
8. MAC Address Table 1024
9. Dimensions and Mass
Dimensions 47(H)x270(W)x1458(D) (mm) includes fixing screws
Mass Less than 1.6 kg
10. Environmental Conditions
Ambient Temperature -15 to +55°C
Relative Humidity 95% (at 40°C)
EMC IEC 60945
Waterproofing IPX0 (IEC 60529)
11.Power and Power Consumption
Power 100-230 VAC
Power Consumption 100mA/100 VAC
ARPA can fail to track a target when the relative speed exceeds 100 kt.
AP2-4
(組)アンテナ部
ANTENNA RADIATOR ASSEMBLY
XN12AF
(008-485-250)
(組)アンテナ部
ANTENNA RADIATOR ASSEMBLY
XN20AF
(008-485-260)
(組)アンテナ部
ANTENNA RADIATOR ASSEMBLY
XN24AF
(008-485-270)
クランプ
CABLE CLAMP
CKS-10-L
-6カクセムスA
(000-106-350)
HEX.WASHER HEAD BOLT *A*
M6X12 SS41 虹
標準 (組)スキャナカバー
SCANNER COVER ASSEMBLY RSB-096 (組)駆動部
RSB-096/097 DRIVING GEAR ASSY
(008-487-180) RSB-096
(008-535-380)
RSB-097 (組)駆動部
DRIVING GEAR ASSY
RSB-097
(008-535-400)
SM-XHコネクタ
SM-XH CONNECTOR
カバーヨウパッキン
03-2130(P2-3P)
PACKING
03-001-3263
(300-132-631)
(組)スキャナカバー
SCANNER COVER ASSEMBLY
RSB-096/097
(008-487-180)
カバーヨウパッキン
PACKING
03-001-3263
(300-132-631)
A
PM付き (組)スキャナカバーPM
SCANNER COVER WITH PM31/ANT (組)アンテナ取付台
PM-31 RADIATOR BRACKET WITH BODY
(008-536-340) RSB-096/097 6カクタッピン
(008-537-160) HEX. TAPPING SCREW
4X8 SUSフランジツキ
A 矢視図 ケーブル(クミヒン)
CABLE ASSEMBLY
SMAPS/PL-MSF358*L150
(000-147-436)
(組)SM-XHコネクタ
SM-XH CONNECTOR
03-2109(R6-6P)
(008-534-850)
AP P R OV E D T IT LE
F AR 2117/2127/2817/2827/2117-B B /2127-B B
D - 1
C HE C K E D R S B -096/097
2003.11.17
DR AWN DWG . NO. C 3519-E 02-A
T.Harazuka
コネクタクミヒン (組)MIC MDキバントリツケイタ組立品 D - 2
CONNECTOR ASSY
L-110 RTR-078 (P)MD ±ナベセムスB (組)XHコネクタ
PRINTED CIRCUIT BOARD XH CONNECTOR
WASHER HEAD SCREW *B*
03P9244 A 03-2105(12-12P)
MIC (008-517-590) M3X8
(008-534-810) ダイオードリミッタ
RTR-078 RU-9603 RTR-079 (P)MD DIODE LIMITER
(組)XHコネクタ (000-147-158) RTR-078 (P)PWR (P)RFC
XH CONNECTOR PRINTED CIRCUIT BOARD RU-9099
RTR-079 RU-9601 PRINTED CIRCUIT BOARD PRINTED CIRCUIT BOARD
03-2102(7P) 03P9244 B (000-126-369)
(000-147-156) 03P9348 A 03P9346
(008-517-600)
(008-536-280) (008-536-310)
ガイドカナグ
RTR-079 (P)PWR J3ハリマーク
W.G. GUIDE
PRINTED CIRCUIT BOARD J3 LABEL
03-001-5303
03P9348 B 03-154-5612
±ナベセムスA (008-536-290) (100-312-800)
WASHER HEAD SCREW *A* サーキュレータ
M4X12 CIRCULATOR
(組)アンプケース
BL-SMコネクタ RC-3686
AMP CASE ASSEMBLY
BL-SM CONNECTOR (000-106-850)
RTR-078/079
03-2129(ファン-R2P)
(008-536-690)
±ナベセムスB スクウェアブッシュ
WASHER HEAD SCREW *B* BUSH RTR-079のみ
M3X8 SB-1909-F シールドカバー組配品
標準 スキャナカバー
NORMAL SCANNER COVER ASSEMBLY
RSB-0074/75/92/96/97 ガイドカナグ
(008-487-180) W.G. GUIDE ブラインドリッド シメツケグランド シメツケグランド
03-001-5303 LID GLAND GLAND
P.MONITOR スキヤナカバーPM (300-153-032) -6カクセムスB ±ナベセムスB JIS F8801 A20ヨウ シンチュウ JIS F8801 20ヨウ シンチュウ JIS F8801 30ヨウ シンチュウ
SCANNER COVER WITH PM31/ANT HEX. WASHER HEAD BOLT (B) WASHER HEAD SCREW *B* (000-870-242) (000-870-194) (000-801-588)
PM-31 ドウハカン M4X20 SUS304 M4X8
(008-536-340) -6カクセムスB WAVEGUIDE (000-882-041) (000-881-445)
03-023-3002 グランドヨウザガネ
HEX. WASHER HEAD BOLT (B)
(100-112-981) ブラインドプレート WASHER
M4X20 SUS304
SEALING PLATE JIS F8801 20C シンチュウ
(000-882-041)
03-023-3006 (000-870-211)
ツリカナグ WGトリツケイタ(1) (100-120-881) ±ナベセムスA VAゴムパッキン ブラインドリッド
HOOK カバーヨウパッキン W.G.FIXING PLATE(1) WASHER HEAD SCREW *A* RUBBER PACKING LID
03-001-3264-0 PACKING 03-023-3003 M4X15 VA-20 JIS F8801 A30 シンチュウ
03-001-3263 (100-112-991) (000-881-147) (000-870-244)
(000-801-402)
(300-132-631) Oリング
グランドヨウザガネ
Eコーナ導波管 O-RING
タイ WASHER
カバ-ヨウボルト E-CORNER WAVEGUIDE AS568-128 1115-70
CABLE GLAND BODY JIS F8801 A30B シンチュウ
HEXAGONAL HEAD BOLT 03-023-3001 (000-851-842)
JIS F8801 20ヨウ シンチュウ (000-870-204)
03-001-3262-2 (100-112-970)
(300-132-622) クランプ (000-870-187)
WGトリツケイタ(2) WIRE CLIP VAゴムパッキン
W.G.FIXING PLATE(2) NO.98-01 RUBBER PACKING
タイ
03-023-3004 (000-515-851) VA-30
スキヤナカバ- CABLE GLAND BODY
(100-113-001) (000-801-589)
SCANNER COVER (組)回転結合器 JIS F8801 A30 シンチュウ
03-001-3261 ROTARY JOINT ASSEMBLY (000-801-587)
-6カクセムスB
RSB-103 カイテンバン.クドウギヤ
HEX. WASHER HEAD BOLT *B*
ロツカ-チエ-ン (008-487-200) ±ナベセムスA DRIVE GEAR WITH TIMING DISK
M4X12 SUS304
CHAIN WASHER HEAD SCREW *A* 03-001-3233/3232
(000-882-040)
ST-16 ステン 13リンク M4X8 (300-132-334)
(000-881-144)
-6カクセムスB ±ナベセムスB SW-XHコネクタ -6カクセムスA
HEXAGONAL HEAD BOLT WASHER HEAD SCREW *B* SW-XH CONNECTOR ASSEMBLY HEX.WASHER HEAD BOLT *A* BPプリント
M8X20 SUS304 M3X15 03-2119(リードスイッチ-2P) M6X12 SS41 虹 PRINTED CIRCUIT BOARD
(000-862-147) (000-881-407) (008-534-720) (000-881-986) 03P9347
(008-536-250)
リードSWトリツケイタ
-6カクセムスB 03-154-3311-2
スライドレール NUT
(100-304-332) (J902)XHコネクタ
03-154-3345 HEX. WASHER HEAD BOLT M6 SUS304
03-2099(5-5P)
(100-308-181) M6X18 SUS304 FW モ-タトリツケイタガイド RFTBプリント
(008-534-730)
(000-800-461) M6 SUS304 MOTOR FIXING PLATE GUIDE PRINTED CIRCUIT BOARD
SW 03-001-3291-0 03P9349A
M6 SUS304 (300-132-910) (008-539-620)
アンテナSWハリマーク ±ナベセムスB
ANTENNA SW LABEL WASHER HEAD SCREW *B*
03-145-3111 M3X8
(100-270-041) (000-881-404) スキャナカバー
モータートリツケイタ
03-154-3321 SCANNER COVER ASSEMBLY
(100-304-341) ドウジククランプ RSB-0074/75/92/96/97
COAX CLAMP
03-154-3322 (008-487-180)
ロッカクボルト
(100-304-350)
HEXAGONAL HEAD BOLT アンテナトリツケダイ ANTENNA BRACKET タンシダイ
M6X40 SUS304
標準 RSB-103-N モ-タ TERMINAL BOARD
(000-862-178)
NORMAL (008-541-680) SCANNER MOTOR (24RPM) FP439AS
D8G-516 30W DC24V (000-147-217)
氷結防止 RSB-103-I
ケーブル(クミヒン) (000-631-715)
DE-ICER (008-541-690) コネクタ(231)
CABLE ASSEMBLY
SMAPS/PL-MSF358*L150 MLP-02P CONNECTOR
231-311/026-FUR
(000-149-689)
スキヤナーカバーPM スキャナーSW
03-154-3401 コネクタ(231)
SCANNER SW CONNECTOR
RSB-096/97-N/I-A/103 ±ナベセムスB M-MLコネクタ 231-314/026-FUR
(008-539-150) WASHER HEAD SCREW *B* 03-2010 (000-147-415)
(組)SM-XHコネクタ
M4X10 (008-504-820)
SM-XH CONNECTOR
(000-881-446)
03-2109(R6-6P)
モーターカバー 6カクタッピンネジ
スキャナーSWフタ
ボールチェーン MOTOR END COVER HEX. TAPPING SCREW
SCANNER SW COVER
SWITCH COVER CHAIN 03-001-3236 4X8 SUS304 フランジツキ
03-154-3832
TM-14-2 L=150 (300-132-360) (000-867-561)
SWフタパッキン
SW GASKET
03-154-3833 SWメイバン
SW NAMEPLATE
PERFORMANCE MONITOR MODULE 03-006-3217
PM-31 スキャナーSWベース MODEL FAR-2827W
(008-536-330) SCANNER SW BASE
03-154-3831
スキャナカバー 6カクボルト
SCANNER COVER HEXAGONAL HEAD BOLT
RSB-098-102-080/104/5 M10X25 SUS316L
(008-538-710)
(000-150-828)
カバーヨウボルト スキャナカバー
HEXAGONAL HEAD BOLT SCANNER COVER
03-163-3161 カイテンケツゴウキ
03-001-3262 ROTARY JOINT ASSEMBLY
アンテナガイド
ボルトヨウパッキン ANTENNA GUIDE RSB-098∼102-080
BOLT GASKET (008-539-870)
03-163-3152
03-163-3165 (100-315-680)
落下防止金具
SAFETY STRAP
03-163-3163
MSSホジョイタ 6カクアナツキボルト
±ナベセムスB MSS SUPPORTING PLATE SOCKET HEAD CAP SCREW
WASHER HEAD SCREW *B* 03-163-3562 M6X16 SUS304 コテイカナグ
M3X8 (100-319-740) カイテンケツゴウキ
波形スプリングピン PWRFCカナグ1(D) (000-809-035) DRIVE GEAR RETAINER
(000-881-404) PWRFC PLATE 1 (D) ROTARY JOINT ASSEMBLY
SPRING PIN 03-015-3228
4X28 SUS 03-163-5515 (100-090-680)
(100-317-670) SPRING WASHER
MSSトリツケイタ M6 SUS304
MSS MOUNTING PLATE クドウギヤ
(000-864-260)
03-163-3561 DRIVE GEAR
スキャナパッキン (100-315-951) アダプター RSB-104 ギヤードモータ MOTOR
03-163-3301
SCANNER GASKET ADAPTOR (100-315-750) RM7398
03-163-3162 03-012-5402 (000-113-840-05)
(301-254-020) RSB-105 ギヤードモータ MOTOR
イチギメボルト
POSITIONING BOLT RM7435
ヘンカンキ 03-015-3231 (000-114-399-05)
RSB098-102-080/104/5 (100-090-700)
TRDハリマーク
TRD LABEL
RSB-104 (P)MSS PRINTED CIRCUIT BOARD 03-163-5516
MSS7497 (100-320-170) ロッキングエッジサドル モータートリツケイタ
(008-513-010) LOCKING EDGE SADDLE 標準 アンテナトリツケダイ RADIATOR BRACKET MOTOR MOUNTING PLATE
ケイコクハリマーク 03-163-3311
WARNING LABEL LES-1017 NORMAL RSB-104/105-N
RSB-105 (P)MSS PRINTED CIRCUIT BOARD (100-315-761)
03-160-1042 (000-150-111) (008-543-500)
MSS7497A
(008-513-020) (100-302-750) 氷結防止 アンテナトリツケダイ RADIATOR BLACKET
タンシダイ DE-ICER RSB-104/105-I
SW
TERMINAL BOARD (008-544-900)
M10 SUS304
LC-02-30T6 3P FW (000-864-261)
(000-116-599) M12 SUS304 イチギメピン NUT
カーリーロック (000-864-132) POSITIONING PIN(M)
M10 SUS304
CABLE CLAMP SW 03-163-3115 (000-863-930)
KLBS-350-16-01A M12 SUS304 (100-315-610)
() (000-864-263)
MODEL FAR-2837SW
APPROVED CHECKED DRAWN UNIT RSB-104/105 空中線部
4 Feb.2005 4 Feb.2005 4 Feb.2005 SCANNER UNIT
H.Kuwamura T.Yoshida N.nakanishi DWG.NO. C3528-E02-A
D - 5
クランプ ナツトザイ(RU-9099)
⑤ スクウェアブッシュ
BUSH ② シールドカバー(25KW)組配品 CABLE CLAMP NUT
SHIELD COVER (25KW) ASSY. CKS-10-L 03-126-5324
(組)RF部 SB-1909-F アンプカバー ±ナベセムスA
(000-106-350) TRリミッタ (100-246-470)
IF AMP COVER WASHER HEAD SCREW *A* TR LIMITER
RF UNIT (組)PHコネクタ 03-154-5603 M4X30
ロッカクボルト スリワリ
RU-9290 HEXAGONAL HEAD BOLT
RTR-081 PH CONNECTOR (組)PHコネクタ (100-304-422) (000-881-156) (000-136-735)
03-2157(12-12P) PH CONNECTOR ① (組)アンプケース
AMP CASE SW
M4X20 SUS304
(008-540-160) 03-2156(14-14P) M4 SUS
(000-862-115)
(008-540-220) RTR-081 サーキュレータ
±ナベセムスA (008-540-210) PW (008-540-190)
M4 CIRCULATOR
WASHER HEAD SCREW *A* (P)IF SW RC-3686
SW ロッカクボルト スリワリ
M4X12 PRINTED CIRCUIT BOARD
① (000-881-146) 03P9335A N
M4 シールドカバー(25KW)
SHIELD COVER (25KW)
HEXAGONAL HEAD BOLT M4 SUS (000-106-850)
±ナベセムスA
(008-537-420) M4X10 SUS304 WASHER HEAD SCREW *A*
M4 (組)BL-XHコネクタ 03-144-5109
③(組)MIC (100-266-810) (000-862-110) M4X20
(組)アンプケース MIC WITH XH CONNECTOR アンプケースツイカコウズ FAN MOTOR アンプケーストリツケイタ (000-881-110)
AMP CASE RTR-079/081
ADDITIONAL WORK FOR IF AMP 03-2120(ファン-2P) AMP CASE MOUNTING PLATE アダプター.2.ツイカコウ
RTR-081 (008-535-540) 03-154-5022 (008-534-780) 03-154-5021 ADOPTER (2)
(008-540-190) (100-317-601) クランプ (100-317-591) 03-010-5310
CABLE CLAMP (301-053-100)
コネクタ(クミヒン) ±バインドセムスF ケイコクラベル(1) (組)XHコネクタ CKS-07-H プリセットラベル
CONNECTOR ASSY WASHER HEAD SCREW WARNING LABEL 1 XH CONNECTOR (000-570-259) RFシヤーシ PRE-SET LABEL
FX2B-40-L=360 M4X8 クロム 86-003-1011 ±ナベセムスB RF CHASSIS 86-960-9001
03-2158(12-12P) 03-154-5601
(000-150-105) (000-806-407) (100-236-231) WASHER HEAD SCREW *B* (000-801-747)
(008-540-230) (100-304-402)
(組)VHコネクタ M3X10 タンシダイ
フタ(X)
To
rem avo
par ove id ele WARN
クランプ
ts cov
ING
ファイバーW
ins er. ctrica
ide No
感電 . use l sho
r-s
サーの恐 erv ck, do
警
TERMINAL
ない ビスれあ ice
abl not
数多 で下 マンり。
(000-881-405)
くあ さい 以外 告 e
り、 。内 の方
万一 部に はカ
VH CONNECTOR
さわ は高 バー
ると 電圧 を開
±ナベセムスB
危険 部分 け
CABLE CLAMP
。
(100-317-550)
7 6
5 4 TB801
3 2
1 14 13
12 11
±ナベセムスA
10 9
VH CONNECTOR
8 7
TBホゴカバー
6 5
4 3
PWR CASE
2 1
03-2159(3-P2P)
3 2
1
TB804 -
TB PROTECTION COVER ±ナベセムスB キヤツプスペ-サ 03-154-5615 WASHER HEAD SCREW *A* 03-1902(3P)
(008-540-240) WASHER HEAD SCREW *B* パルストランス
03-154-5023 CAP SPACER (100-304-450) M4X15 PULSE TRANSFORMER (008-486-900)
M4X10 CS-10S TFコン
(100-321-880) (000-881-145) RT-9023 TF CAPACITOR
(000-881-446) (000-809-335) FETオサエイタ
タンシダイ (000-123-394) ECQ-V1H104JL3
TERMINAL BOARD コネクタ(クミヒン) FET SUPPORTING PLATE
(000-129-126)
FP439AS CONNECTOR ASSY
TNC-PS-3C L430MM
③ (組)MIC
MIC WITH XH CONNECTOR
03-144-5107
(100-264-190)
000147217 コネクタクミヒン キンゾクサンカヒマクR
TBキバントリツケイタ(X) (000-150-109)
CONNECTOR ASSY ④ MDキバントリツケイタ組立品 METAL OXIDE FILM RESISTOR
TB PCB MOUNTING PLATE (X) ホキョウイタ MD PCB MOUNTING PLATE ASSY. BSR10HA1K OHMJ
REINFORCEMENT PLATE
L-110 +ナベコネジ
03-154-5006 (000-145-230)
ソトハTW
エッジサドル 03-154-5005 (組)XHコネクタ PAN HEAD SCREW
(100-317-541) ±ナベセムスA TOOTH LOCK WASHER
EDGE SADDLE (100-317-530) XH CONNECTOR MIC M4X20
WASHER HEAD SCREW *A* M3
+アプセットUIセムスB EDS-3 03-2102(7P) RU-9601 (000-861-131)
FIXING SCREW M4X10
(000-108-152)
M6X16 SUS304 ⑤ (組)RF部 (000-147-156) (000-881-145) マグネトロン
(000-800-420) RF UNIT MAGNETRON
クランプ
ケーブルオサエイタ(X)
±ナベセムスB
④ MDキバントリツケイタ組立品
MD PCB MOUNTING PLATE ASSY.
(組)VH-ELコネクタ
VH-EL CONNECTOR WIRE CLIP MG5436
CABLE SUPPORTING PLATE (X) WASHER HEAD SCREW *B* №98-01 (000-140-762)
03-2103(2-R2P)
03-154-5004 (008-534-790) (000-515-851)
M4X20
(100-317-520) (P)MD SW
(000-881-451) PRINTED CIRCUIT BOARD (組)NH-XHコネクタ クランプ M4 N
03P9244 B NH-XH CONNECTOR CLAMP
ケーブルクランプ(X) M4
CABLE CLAMP (X) (008-517-600) 03-2104(13-13P) CKS-10-H
ボウスイフィルム.RF. (008-534-800) (000-570-242)
03-154-5003 MDキバントリツケイタ
ケース(X) WATERPROOFING FILM RF
(100-317-510) MD PCB MOUNTING PLATE
CASE (X) 03-010-5123 MODEL FAR-2827W
PW 03-154-5001 (100-070-631) 03-144-5105
±ナベセムスB M4 SUS (100-264-170)
WASHER HEAD SCREW*B* SW (100-317-491) ヘンカンWG
M4X25 M4 SUS アースマーク CONVERSION WAVEGUIDE ホウネツシート
EARTH LABEL FET INSULATION SHEET APPROVED CHECKED DRAWN UNIT RTR-081 送受信部
(000-881-452) チヨウボルト 03-154-5011
03-144-1438 (100-317-570) 03-144-5106
WING BOLT
(100-266-480) (100-264-180) 22 DEC.2004 22 DEC.2004 22 DEC.2004 TRANSCEIVER UNIT
M4X10 SUS304
(000-862-516) H.Kuwamura T.Yoshida S.KUBOTA DWG.NO. C3527-E01-A
D - 6
イチギメピン(C) サ-キユレ-タ クランプ クランプ キバンシヤーシ (組)MDケース
POSITIONING PIN(C) CABLE CLAMP WIRE CLIP PCB CHASSIS
CIRCULATOR
NO.98-01 03-163-5017
MD PCB CASE ASSY.
03-163-3514 RC-4910S CKS-10-L
(100-315-801) (000-106-350) (000-515-851) (100-317-400)
(000-126-346)
ロツカクセムスB スリワリ
HEX.WASHER HEAD BOLT
ハリマーク(S) (P)MD
M6X25 SUS304 PRINTED CIRCUIT BOARD
Eコ-ナWG サーキユレータトリツケイタ2 LABEL(S)
(000-802-771) CIRCULATOR MOUNTING PLATE2 03-163-5051 03P9244E
E CORNER WAVEGUIDE
03-163-5008 (100-317-473) (008-539-590)
03-016-5301 (P)PWR ホウネツシ-ト
TRリミツタ (100-050-091) (100-317-321)
TR LIMITER PRINTED CIRCUIT BOARD FET INSULATION SHEET
SバンドMIC サーキユレータトリツケイタ1 (組)BL-SMコネクタ 03P9348C 03-144-5106
MIC TL378A CIRCULATOR MOUNTING PLATE1 BL-SM CONNECTOR
(000-149-672) (008-539-600) (100-264-180)
RU-9427 03-163-5007 シヤーシ 03-2154(ファン-R2P)
(000-141-059) (100-317-310) CHASSIS (008-540-660) FETオサエイタ(S)
+アプセッットセムスB 03-163-5021 FET SUPPORTING PLATE (S)
WASHER HEAD SCREW アダプタ (100-317-411) (P)RFC 03-163-5018
ADAPTER ±ナベセムスB
M5X16 SUS304 PRINTED CIRCUIT BOARD WASHER HEAD SCREW *B* (100-319-300)
(000-801-516) 03-163-5006 ±ナベセムスB 03P9346A
(100-317-300) M4X15
WASHER HEAD SCREW *B* (008-545-220)
(組)シャーシ (000-881-448)
M4X35
(組)MIC
② (組)キバンシャーシ
(000-808-650) CHASSIS ASSY.
MIC ASSEMBLY
RTR-082-104/105 ケースフタ ③ PCB CHASSIS ASSY.
(008-540-540) CASE COVER
03-163-5026 (組)PHコネクタ
(100-317-460) PH CONNECTOR ±バインドセムスF ケイコクラベル(1)
コネクタ(クミヒン) WARNING LABEL 1
CONNECTOR ASSY
03-2162(14-14P) WASHER HEAD SCREW MDケース
(008-540-690) M4X8 86-003-1011 MD PCB CASE
TMP-1.5D-QEV L240 (組)PHコネクタ (100-236-231)
(000-806-407)
(000-150-107)
(組)XHコネクタ
PH CONNECTOR
03-2161(12-12P)
④ 03-163-5015
(100-317-381)
ケーブルケース クランプ フタ(S)
XH CONNECTOR CABLE CASE CABLE CLAMP (008-540-680)
LID (S)
(組)サーキュレータ/MIC
03-2146(7P)
(008-540-580)
03-163-5025
(100-317-451)
CKS-10-L
(000-106-350)
① CIRCULATOR/MIC
コネクタ(クミヒン)
CONNECTOR ASSY
IF-フタ
IF AMP PCB COVER
03-163-5002
(100-317-260) ⑤ (P)IF
TNC-PS-3C L290MM 03-163-5024
(000-147-705) PRINTED CIRCUIT BOARD
+ナベセムスネジBK ケイコクハリマーク +ナベセムスBK (100-317-440)
(組)SM-XHコネクタ 03P9335B
WASHER-HEAD SCREW WARNING LABEL WASHERHEAD SCREW BK SM CONNECTOR
ホゴカバー
M4X12 03-160-1042 M4X15 PROTECTION COVER (008-543-330)
03-2153(P2-2P) ±ナベセムスB
(000-804-658) (100-302-750) (000-805-724) (008-540-650) 03-163-5028
WASHER HEAD SCREW *B*
タンシダイ (組)XHコネクタ (100-319-290)
XH CONNECTOR
M4X10
⑤(組)IFケース +アプセットUIセムスB ±ナベセムスB
タンシバン TERMINAL BOARD (000-881-446) FIXING SCREW
TERMINAL PLATE 03-2152(12-12P) IF AMP PCB CASE ASSY. WASHER HEAD SCREW *B*
LC-02-30T6 2P (008-540-640) M6X20 SUS304
03-163-3553 M3X8
(000-116-597) (組)XHコネクタ (000-807-434)
(100-315-910) スクウエアブツシユ (000-881-404)
ゼツエンダイ XH CONNECTOR ③ (組)基板シャーシ マグネトロン BUSH
INSULATION BOARD 03-2172(2-2P)
PCB CHASSIS ASSY. MAGNETRON
03-163-3552 (組)NH-XHコネクタ (008-544-930) SB-1909-F
コウアツマ-ク(2) MG5223F
(100-315-900) NH-XH CONNECTOR (000-109-081) (000-126-024)
HIGH VOLTAGE WARNING LABEL
コネクタ(クミヒン)
16-018-3206
トランスダイ(2)
TRANS MOUNTING PLATE (2)
03-2150(13-13P)
(008-540-620) CONNECTOR ASSY
(組)XHコネクタ
④ ② (組)シャーシ
(100-297-770) K2 リレー XH CONNECTOR (組)MDケース IFケース
03-163-5014 FX2B-40-L=360 03-2149(3-2P) MD PCB CASE ASSY. CHASSIS ASSY.
RELAY IF AMP PCB CASE
(100-317-371) (000-150-105) K1 リレー (008-540-610) RTR-082-104/105
TFコン -104 TR-0NH/3 1.7A ケツロボウシザイ 03-163-5023
+ナベセムスBK RELAY (008-540-560)
TF CAPACITOR ロツカクボルト スリワリ WEEP PROTECTION BLOCK (100-317-431)
(組)メイテンロック WASHERHEAD SCREW BK (000-137-509) HG3-DC12V AP6231 HEXAGONAL HEAD BOLT
MATE-N-LOK M4X8 ECQ-V1H104JL3
(000-129-126)
-105 TR-0NH/3 0.8A (000-454-822) ⑧パルストランス M6X16 SUS304
03-030-5206
(100-134-470)
03-2155(P2P) (000-149-950)
(000-137-508) XK1 リレーソケット PULSE TRANSFORMER (000-862-129)
(008-540-670) (組)VHコネクタ
VH CONNECTOR RELAY SOCKET
03-2147(3P) AP68379
T801トランス(パルス) (組)VHコネクタ (000-145-343) ボウスイシ-ト(アンテナ)
(008-540-590)
PULSE TRANSFORMER VH CONNECTOR WATERPROOF SHEET (ANTENNA) キヤツプスペ-サ
トランスダイ(1)
RT-9273 03-2148(2-2P) CAP SPACER
(000-136-734)
TRANSFORMER MOUNT (1)
(組)XHコネクタ (008-540-600)
03-002-4119
CS-10S
(組)IFケース
03-163-5013 (100-093-860)
(100-317-361)
XH CONNECTOR ①(組)サーキュレータ/MIC (000-809-335) IF AMP PCB CASE ASSY.
03-2151(4P) CIRCULATOR/MIC
マキセンR ソトハTW (008-540-630)
WIREWOUND RESISTOR TOOTH LOCK WASHER RTR-082-104/105 タンシダイ
BGR10THA560J
(000-150-144)
M3
DIODE(RECTI) ⑦
(組)TB基板取付板(S) (008-540-530) ⑥ TERMINAL BOARD
MD-12N1 TB PCB MOUNTING PLATE (S) ASSY. ケースアシ(1) LC-02-30T6 3P
(000-133-735)
CASE BASE PLATE (1) (000-116-325)
タンシダイ 03-163-5032
(100-321-200) ケイコクハリマーク
TERMINAL クランプ WARNING LABEL
STK-A8 保護カバー2
±ナベセムスB
PROTECTION COVER 2 CABLE CLAMP 03-160-1042
WASHER HEAD SCREW *B* (000-135-509) +アプセットセムスB CKS-13-L (100-302-750)
M3X10 ファイバーW 03-163-5029 WASHER HEAD SCREW
(100-320-320) (000-104-832)
(000-881-405) FIBRE WASHER クランプ
M3
M6X12 SUS304
パルストランス CABLE CLAMP
キンゾクサンカヒマクR
(000-808-428)
CKS-10-L
PULSE TRANSFORMER
⑧ RTR-082
METAL OXIDE FILM RESISTOR
BSR10HA1K OHMJ
⑥ (組)端子台板
TERMINAL BOARD BASE ASSY.
メクラブタ
BLIND PLATE ケースカナグ
(000-106-350)
(008-541-700) (000-145-230)
03-030-0401 CASE FIXING PLATE タンシダイイタ
カバー2 (100-091-640) 03-163-5003 TERMINAL BOARD BASE
COVER 2 (100-317-271)
タンシダイ 03-163-5027
03-163-5005 (100-319-312)
TERMINAL BOARD +アプセットUIセムスB (100-317-290)
FIXING SCREW ハリマーク(S)
FP439AS
LABEL(S)
(000-147-217) M6X16 SUS304 (組)端子台板
(P)RFTB (000-800-420) ケースアシ(2) 03-163-5051
CASE BASE PLATE (2) (100-317-473) TERMINAL BOARD BASE ASSY.
PRINTED CIRCUIT BOARD ケーブルオサエイタ(S)
03P9349A 03-163-5033
CABLE SUPPORTING PLATE (S)
(008-539-620) 03-163-5012
PW (100-321-210)
アースハリマーク
MODEL FAR-2837SW
M4 SUS304
TBキバントリツケイタ(S) (100-317-350) カバー1 EARTH LABEL
TB PCB MOUNTING PLATE (S) SW COVER 1 10-044-4133
03-163-5022
±ナベセムスB
M4 SUS304 03-163-5004
(100-317-281)
(100-304-060) APPROVED CHECKED DRAWN UNIT RTR-082 送受信部
(100-317-420) ケーブルクランプ(S) ケース(S)
WASHER HEAD SCREW *B*
ドウジククランプ
COAX CLAMP M4X25 CABLE CLAMP (S) 蝶ボルト 2種
WING BOLT
±バインドセムスF
WASHER HEAD SCREW
CASE (S) 22 DEC.2004 22 DEC.2004 22 DEC.2004 TRANSCEIVER UNIT
03-163-5011 03-163-5001
03-154-3322 ⑦ (組)TBキバントリツケイタ(S) (000-881-452) M4X10 SUS304 M4X8 C2700 MBCR2 (100-317-252)
(100-304-350) TB PCB MOUNTING PLATE (S) ASSY. (100-317-340)
(000-806-407)
H.Kuwamura T.Yoshida S.KUBOTA DWG.NO. C3528-E01-A
D - 7
PSUハリマーク
LABEL PSU
リレー
03-163-9814
(100-319-781) コウアツマ-ク(2) RELAY
HIGH VOLTAGE WARNING LABEL HG3-DC12V AP6231
16-018-3206 (000-454-822)
(100-297-770)
PSUシャーシ
PSU CHASSIS
03-163-9811
(100-315-980)
+ナベセムスネジBK
SCREW BK
+ナベセムスネジBK M4X20
SCREW
M3X15
リレーソケット
RELAY SOCKET
AP68379
タンシダイ (000-145-343)
TERMINAL BOARD
PSUクランプイタ
LK-2P
PSU CLAMPING PLATE
(000-533-501)
03-163-9813
(100-316-000)
+-ナベセムスネジB
SCREW MODEL FAR-2137S/2137S-BB/2837S
M4X10 +アプセツトUIセムスB PSUクランパー
FIXING SCREW PSU CLAMPER APPROVED CHECKED DRAWN UNIT
M6X16 SUS PSU-007 電源制御部
03-163-9812
20 OCT.2004 20 OCT.2004 20 OCT.2004 POWER SUPPLY UNIT
(100-315-991)
H.Kuwamura T.Yoshida S.kubota DWG.NO. C3521-E02-A
D - 8
ケイコクラベル(1)
(P)NET100 フインガ-ガ-ド (組)BL-SMコネクタ
WARNING LABEL 1 FINGER GUARD
PRINTED CIRCUIT BOARD (P)SPU FAN
86-003-1011 FG-06ULB
03P9332 PRINTED CIRCUIT BOARD 03-2082(ファン-R2P)
(000-144-485) (008-534-870)
(008-536-210) 03P9337
カバー
蝶番 (008-536-460)
COVER
HINGE
03-163-8001 クランプ
TH-TM-5 スクウエアブッシュ
(100-304-553) SPUシールドケース SPU取付板 CLUMP
(000-872-005) BUSH
SPU SHIELD CASE SPU MOUNTING PLATE SB-1909-F CKS-05-L
SPU取付板組立品
03-163-8025 ナット材 03-163-8012
SPU MOUNTING PLATE ASSY.
(100-308-300) NUT
(100-304-573)
10-071-6308 ※
電源カバー組立品 ※
フアンダクト
POWER SUPPLY COVER ASSY. (100-289-380) ※
※ FAN DUCT
ファンダクト組配品 03-163-8017
SPU取付板組立品 ファンダクト組配品
FAN DUCT ASSY. (100-304-621)
SPU MOUNTING PLATE ASSY. FAN DUCT ASSY.
電源カバー組立品 (組)XHコネクタ
J3
+-ナベセムスネジ
WASHER HEAD SCREW *A*
M4X8
クランプカナグ
CLAMP FIXTURE
03-163-7506
カバー組立品
W1 ケーブル(クミヒン) 矢視図
A
COVER ASSY. CABLE ASSEMBLY カバー組立品
RCU-014 XH10P-W-5P L=10M COVER ASSY.
(000-149-056)
RCU-014A XH10P-W-6P L=2.3M レクトラDスプリング
(000-150-000) LECTRA D SPRING
#6601-P
(000-802-139)
+ナベSタイトUIザツキ クランプダイ エンコーダダイアル
PAN HEAD S-TIGHT SCREW CLAMP PLATE ホゴシート DIAL
03-163-7505 PROTECTION SHEET 03-163-7503
3X8 SWRM10 MFZN2-C
(000-804-539) 03-163-7507 (100-305-161)
(100-305-402)
(組)XH-PADコネクタ
XH-PAD CONNECTOR
03-2118(12-16P) +ナベセムスBK エンコーダダイアル組立
(008-534-740) WASHER HEAD SCREW DIAL ASSY.
M3X8
(000-804-626)
(P)PNL レクトラDスプリング
PRINTED CIRCUIT BOARD # LECTRA D SPRING
03P9343 #6601-P
(008-536-360) # # (000-802-139)
#
# ツマミ
ブザーコテイゴム KNOB
BUZZER FIXING RUBBER 03-163-7504
ラバーキー(E) 03-163-7512 (100-305-171)
E RUBBER KEY (E) ホウネツシ-ト(1) (P)BUZ
03-163-7551 HEAT SINK RUBBER(1) PRINTED CIRCUIT BOARD ツマミ組立品
(100-305-441) 10-071-2007 03P9362 KNOB ASSY.
ラバーキー(J) (008-536-370)
J RUBBER KEY (J)
03-163-7561
(100-306-270) デイストレスカバ-フクロ
DISTRESS SWITCH COVER
DSC-60
+-ナベセムスB コキュウシート (005-950-570)
WASHER HEAD SCREW *B* RESPIRATION SHEET
03-163-7511 エンコーダダイアル組
M3X8
DIAL ASSY.
ツマミ組
ソウサパネル KNOB ASSY.
KEYBOARD PANEL
03-163-7501 スライドシート
(100-305-645) SLIDE SHEET
03-163-7509
TB1
トラックボール
TRACK BALL
TA4726
(000-147-139)
MODEL FAR2117/2127/2817/2827/2117-BB/2127-BB
FAR2137S/2837S/2837SW/2827W/2137S-BB
D - 9
クランプ
CABLE CLAMP
CK-07H
シールドケース スペーサ
SHIELD CASE SPACER
03-163-7805 03-163-7806
(100-305-513)
SW +バインドセムスF グロメツト
M3 BINDER HEAD SCREW GROMMET
+-ナベセムスネジB M3X8 クロム G-49
WASHER HEAD SCREW *B* (000-881-960)
M3X8
(組)XH-PADコネクタ
XH-PAD CONNECTOR ASSEMBLY スペ-サ
SPACER
03-2123(12-16P)
SQ-8
(008-536-710) カバー
COVER
03-163-7802
スペ-サ (100-305-672)
SPACER スペーサ
SQ-25 SPACER
CZ-413
(000-147-166)
PW
M3
ラバーキー(E)
RUBBER KEY (E)
(P)KEYTB 03-163-7851
PRINTED CIRCUIT BOARD (100-305-561)
03P9344
(008-536-380) ボタンカバー
BUTTON COVER
コキュウシート RCU-016 03-163-7841
スペ-サ
SPACER RESPIRATION SHEET (100-305-571)
SQ-25 03-163-7511 デイストレスカバ-フクロ
DISTRESS SWITCH COVER
RCU-015
DSC-60
SW (005-950-570)
サンタンシオサエイタ M3 操作パネル
3-PORT CLAMP PLATE FRONT PANEL
03-163-7803 03-163-7801 操作パネル
(100-305-661) FRONT PANEL
ギャップパッド
GAP PAD
GP1-0.5-011-016
+-ナベセムスA
TB1
トラックボール WASHER HEAD SCREW *A*
TRACK BALL M4X8
TA4726 (000-881-144)
(000-147-139)
MODEL
FAR-2117/2127/2817/2827/2117-BB/2127-BB
FAR-2137S/2827W/2837S/2837SW/2137S-BB
APPROVED CHECKED DRAWN UNIT RCU-015/A/016
D - 10
操作部
29 OCT.2004 29 OCT.2004 29 OCT.2004 CONTROL UNIT
H.Kuwamura T.Yoshida S.KUBOTA DWG.NO. C3519-E05-B
D - 11
ハイメンカバー(20) コネクタカバー(20)
REAR COVER (20) ケイコクラベル(1) CONNECTOR COVER (20)
03-163-1091 WARNING LABEL 1 03-163-1093
(100-305-083) 86-003-1011 (100-305-102)
シールドケース(20)
PCB ハリマークAC(20)
LABEL AC (20) SHIELD CASE (20)
PRINTED CIRCUIT BOARD AC 03-163-1031 03-163-1062
(本図はAC仕様)
03P9359 (100-305-011) (100-308-470)
(000-147-376)
ハリマークDC(20)
(組)DCデンゲン DC LABEL DC (20) コネクタ(クミヒン)
03-163-1041
DC POWER PACK (100-305-020) CONNECTOR ASSY.
AC
MU-231CR VH6P-XH2P
(008-543-580) PCB (000-150-738)
PRINTED CIRCUIT BOARD コネクタ(クミヒン)
SLB-FRN3-A DC CONNECTOR ASSY.
(組)ACデンゲン
(000-150-737) VH6P-VH6P
AC POWER PACK (本図はAC仕様)
(000-150-739)
MU-231CR ハイメンパネル(20)
(008-543-560) REAR PANEL(20)
03-163-1023
(100-304-991)
フイルタ(クミヒン)
AC FILTER ASSEMBLY
AC MU-201CRヨウ (ACシヨウ)
(000-149-060)
シャーシ(20)組立品 フイルタ(クミヒン)
CHASSIS (20) ASSY. DC DC FILTER ASSEMBLY
MU-201CRヨウ (DCシヨウ)
LCD一式の時 (000-149-061)
フレームC(20)
FRAME C (20)
03-163-1022 LCD
(100-304-982) 201MU-1
(000-149-059)
シャーシ(20)
CHASSIS (20)
03-163-1021
(100-304-972)
PCB(インバータ)
PRINTED CIRCUIT BOARD バックライトユニット
201PW21F BACK LIGHT MODULE
(000-150-305) 201LHS2F
(000-150-304)
MODEL FAR-2117/2127/2137S
ケイコクラベル(1) コネクタカバー(23)
WARNING LABEL 1 CONNECTOR COVER (23)
86-003-1011 03-163-2062
(100-305-362)
ハイメンカバー(23)
REAR COVER (23) PCB
03-163-2061 PRINTED CIRCUIT BOARD
(100-305-353) 03P9359
(000-147-376)
(組)DVI I/F BOARD
PRINTED CIRCUIT BOARD
MU-231CR フインガーガード
(008-536-530) FINGER GUARD
FG-06ULB (組)ACフィルタ
(000-144-485) (組)DCデンゲン
AC AC FILTER ASSEMBLY
(008-536-500) DC POWER PACK
ファンモータ
FAN MOTOR (組)DCフィルタ MU-231CR
MMS-06C12DS-R02 DC DC FILTER ASSEMBLY (008-543-580)
(000-128-408) (008-536-510)
(P)FILTER (組)ACデンゲン
PRINTED CIRCUIT BOARD (本図はAC仕様) AC POWER PACK
03P9360 MU-231CR
(008-536-520) (008-543-560)
フレームC(23)
FRAME C (23)
03-163-2022 ハイメンパネル(23)
(100-305-301) REAR PANEL (23)
03-163-2023
(100-305-313)
シャーシ(23) シャーシ(23)組立品
CHASSIS (23) CHASSIS (23) ASSY. レイインキヨクカン
03-163-2021 (組)LCD CCFL
(100-305-294) LCD FLCL-23
MU-231CR (000-149-467)
(008-536-490)
LCD関連部品
LCD SERVICE PARTS
シャーシ(23)組立品
CHASSIS (23) ASSY.
MODEL FAR-2817/2827/2827W/2837S/2837SW
コフタ
SMALL LID
(P)NET100 03-163-9014
NET100 BOARD
(100-304-512)
03P9332
(008-536-210) カバー
COVER
Oリング 03-163-9012
付属品 (100-305-633)
Accessovies (組)MJ-VHコネクタ
MJ-VH CONNECTOR
03-2095(R3-3P)
(008-534-680)
イタバネ
コフタウライタ PLATE SPRING
BACK LID 03-163-9016
03-163-9015 (100-306-080)
スペ-サ (P)CARDCPU (100-304-523)
SPACER CARDCPU BOARD
SQ-16 03P9333
(000-801-854) (008-536-200)
コフタウライタ組立品
BACK LID ASSY.
コフタウライタ組立品
BACK LID ASSY.
マエパネル組立品
FRONT PANEL ASSY.
N
付属品 ケショウパネル
Accessovies COSMETIC PANEL
03-163-9021
シヤーシ (100-304-531)
CHASSIS
03-163-9011
(100-304-482) マエパネル
FRONT PANEL
03-163-9013
(100-305-622)
(P)CARDCON
CARDCON BOARD
03P9345
(008-536-220)
マエパネル組立品
FRONT PANEL ASSY.
MODEL FAR-2117/2127/2817/2827/2137S/2837S/
2117-BB/2127-BB/2137S-BB
APPROVED CHECKED DRAWN UNIT CU-100 メモリーカードインターフェイス
30 Sep.2004 30 Sep.2004 30 Sep.2004
MEMORY CARD INTERFACE UNIT
H.Kuwamura T.Yoshida S.kubota DWG.NO. C3519-E08-B
Contents of Drawings
Contents of Drawings
S-0
Contents of Drawings
S-0A
D
C
B
A
110/115/220/230VAC,
03-2088(6-14P) DPYC-1.5 *1
2
1
14
13
1φ,50-60Hz RU-3305 *2
J1
DPYCY-1.5 *1
100VAC,1φ,50-60Hz
J5(VH)
03-2090(3P)
RW-4747
1
*4
GYRO
BRN GYRO_R2 J613(TB)
64P1106A
RW-9600,φ22.1,
BOARD
J680 RED 2 GYRO_R1 TX_HV 1
*2
3 NC 2 15/30/40/50m MAX.100m
NC
3 NC
TB901
TB-801
チャ チャ BRN
CONVERTER
1 1 TX_HV
1
アカ
J4(VH)
2 J610 2 NC
2 100VAC_C
1 100VAC_H
03-2091(5P) キ
4 GYRO_S2 4 24V_MINUS
J911
24V_MINUS 2
F.G.
DATA1-C
DATA1-H
ダイ
アカ
チャ
5
4
3
2
1
*5
*1
*4
*3
*2
*1
MOTOR(+) 3 5 MOTOR(+)
6 アオ BLU 4 GYRO_T ハイ(太) GRY[B]
:
MPYC-7
:
:
:
:
MOTOR(+) 6 MOTOR(+)
5
SHIFT1-C 4
SHIFT1-H 3
2
1
4
NOTE
PPL
YEL
ORG
RED
BRN
ムラサキ 5 GYRO_FG ムラサキ(太) PPL[B]
J7(NH)
GYROCOMPASS 7 MOTOR(-) 5 7 MOTOR(-)
1
2
3
4
5
6
MOTOR(-) 6 8 MOTOR(-)
アカ RED 9 SPU_RF_D_A
SPU_RF_D_A 7
OPTION
J608(TB) J603(XH) SPU_RF_D_B 8 ミドリ GRN 10 SPU_RF_D_B
AD_DATA_H クロ BLK 11 RF_SPU_D_A
1 RF_SPU_D_A 9
P
-12V
GND
+5V
GND
+12v
シロ WHT
USER SUPPLY
2 AD_DATA_C RF_SPU_D_B 10 12 RF_SPU_D_B
空中線部
*1 ミドリ(太) GRN[B]
J615(TB)
3 AD_CLK_H SG 11 13 SG
5
4
3
2
1
TTYCS-4 P アカ(太) RED[B]
PM-31
SHIPYARD SUPPLY
RSB-096/097
ミドリ チャ
( SHIPYARD SUPPLY )
キ J609 TB-802
アカ
PERFORMANCE MONITOR
IF_VIDEO
BRN
ダイ IF_VIDEO
パフォーマンスモニター
GRN
RED
YEL
ORG
3
2
1
6
5
4
3
2
1
J3
TOTAL : UP TO 31.5m
J4
NC
NC
GND
VCC
GND
GND
合計 : 31.5m以下
+12V
+12V
03P9342
TB BOARD
XH10P-W-5P-A
コンバータ
XH10P-W-6P
-5/-12V
J3 1.5/10/20/
RGBビデオ
2.3m,φ9
DVI-RGB-1
CONVERTOR
RGB VIDEO
2
DVI1TX2_N 1 30m,φ9
2 J602 J501/J521 J502/J522 J501
DVI1TX2_P
*2
A_GND 3
4 KEY_TXD_A 2 2 KEY_TXD_A KEY_TXD_A 2 2 KEY_TXD_A
NC
5 KEY_RXD_B 3 3 KEY_RXD_B KEY_RXD_B 3 3 KEY_RXD_B
NC
6 KEY_RXD_A 4 4 KEY_RXD_A KEY_RXD_A 4 4 KEY_RXD_A
NC
03P9229A
J9 NC 7
8 GND 6 6 GND GND 6 6 GND
1
RCU-015
RCU-014
10 8 19
DSUB-BNC-1
GND GND SLB-FRN4-A A_GND
11 9 20
CONTROL UNIT
CONVERTOR *2
GND V_SYNC NC
BNCコネクタコンバータ
BNC CONNECTOR
12 NC GND 10 NC 21
13 H_SYNC VCC 11 A_GND 22
14 Y_SYNC GND 12 DVI1TXC_P 23 J605(TB)
15 NC -5_-12V 13 DVI1TXC_N 24 HDG_A 1
P *1
*4
*3
*2
*1
3
HDG_B 2
TTYCS-1Q
:
:
:
:
HDG_GND 3
注記
HDG SENSOR
(IEC-61162-2)
J616(NH)
1 GND J607(TB)
*1
2 OP_HD_IN LOG_A 1
TTYCS-1
P
3 GND LOG_B 2
オプション
造船所手配
SPEED LOG
4 OP_BP_IN NC 3
ユーザー手配
(IEC-61162-1)
5 GND
6 OP_TRIG_IN
7 GND J606(TB)
RW-4864,φ9.5 *1
MASTER RADAR 8 OP_VIDEO_IN NAV_A 1
TTYCS-1
NAV_B 2 P
J617(NH)
NAVIGATOR
NC 3 (IEC-61162-1)
1 GND
2 OP_HD_1
3 GND J619(TB)
4 OP_BP_1
*1
ARPA_A 1
5 GND ARPA_B 2 P TTYCS-1
ECDIS
6 OP_TRIG_1 NC 3 (IEC-61162-1)
SUB DISPLAY1 RW-4864,φ9.5 7 GND
(FULL-LOG) 8 OP_VIDEO_1
J618(NH) J601
SHIP'S ALARM SYSTEM
最長 100m ( 100mを超える場合はRJB-001が必要 )
GND
船内アラームシステム
4
NC 1 RS-232C CABLE
2 OP_HD_2 2
RXD PC
3 GND 3
TXD
*5 : 交流は両極切りブレーカ(造船所手配)を経由すること
4 OP_BP_2 4
NC
5 GND
GND 5
6 OP_TRIG_2
RS-232C
NC 6
*1 *5 SUB DISPLAY2 RW-4864,φ9.5 7 GND 7
NC
BREAKER (SEMI-LOG) 8 OP_VIDEO_2
NC 8
*1 TB1 TB1
100-120/200-240VAC DPYC-2.5 0.6m NC 9
H
1φ, 50-60Hz 1 1 H
SCALE
DRAWN
C
2 2 C
DWG.No.
CHECKED
APPROVED
J204 DVI-D MONITOR J611(TB)
*1
トランス
1 DVI0TX2_N 1
DPYC-1.5 AIS_TD_A
Feb. 2, '05 440VAC 2 DVI0TX2_P AIS_TD_B 2 P
RU-1803
NC AIS_RD_B 4
TTYCS-4
MASS
TRANSFORMER
5 NC AIS_GND 5 AIS
6 NC (IEC-61162-2)
7 NC
Y. Hatai
8 NC
RCN-001/002
C3519-C05- C
SLIM CONSOLE
9 DVI0TX1_N J620(TB)
TAKAHASHI.T
E. MIYOSHI
100-230VAC
kg
10 DVI0TX1_P TRK_TD_A 1
11 A_GND
スリムコンソール
TRK_TD_B 2 *1
5
12 NC TRK_RD_A 3
制御部
P TTYCS-1
13 TRK_RD_B 4
RPU-013
NC TRACK_CONTROL
14 VCC GND 5
(IEC-61162-1)
TTYCS-1
TB1 15
*1
1.3m GND
IV-1.25sq.
*1
1 16 NC
17 DVI0TXD_N
PROCESSOR UNIT
2 *1
18 DVI0TXD_P J612(TB)
3
2
1
TTYCS-7
19 A_GND ALARM1_0 1
ALARM1_1 2 P
20 NC
AC
AC
GND
21 NC ALARM2_0 3
DVI-D/D ALARM2_1 4 P
22 A_GND
J3 ALARM3_0 5
表示部
SINGLELINK5M,φ7 23 DVI0TXC_P P
ALARM3_1 6 *1 LAN CABLE (CAT5) OR
TMDS_DATA2(-) 1 24 DVI0TXC_N OPERATOR_FITNESS_0 7
2 P FR-FTPC-CY, 10/20/30m, φ13
HUB-100
TMDS_DATA2(+) OPERATOR_FITNESS_1 8
(8PORTS)
DVI-D MONITOR P
名 称
5 TXN
SWITCHING HUB
NC J205 SYS_FAIL_H 11 2
P シロ/ダイ WHT/ORG
DDC_CLOCK 6 1 DVI0TX2_N SYS_FAIL_C 12 3 RXP
アオ BLU
DDC_DATA 7 2 DVI0TX2_P 4 NC
シロ/アオ WHT/BLU P
*2
NC 8 3 A_GND 5 NC
ダイ ORG
TMDS_DATA(-) 9 4 NC 6 RXN
10 シロ/チャ WHT/BRN NC
7
MU-231CR (FR-2817/2827)
MU-201CR (FR-2117/2127)
TMDS_DATA(+) 5 NC チャ BRN
TMDS_DATA1/3_SHIELD 11 6 NC 8 NC
NC 12 7 NC
6
NC 13 8 NC
相互結線図
+5V_POWER 14 9 DVI0TX1_N
GND 15 10 DVI0TX1_P
HOT_PLUG_DETECT 16 11 NETWORK MPS588-C J302
A_GND P5E-4PTX-BL, 10m, φ6.3
TMDS_DATAB(-) 17 12 NC TXP 1 1 TXP
CU-200
NC 20 15 NC 4 4 NC
LAN
GND
NC 21 NC 5 5 NC
CARD I/F UNIT
カード I/F ユニット
16 NC
TMDS_CLOCK_SHIELD 22 17 DVI0TXD_N RXN 6 6 RXN
INTERCONNECTION DIAGRAM
*3 A_GND
ア−ス銅版 *1 23 DVI0TXC_P GND 2 2 GND
COPPER STRAP DVI CABLE 3 FG
24
S - 1
DVI0TXC_N
W=50 EXT. MONITOR
FAR-2117/2127/2817/2827 (RCN001/002)
D
C
B
A
*4
*3
*2
*1
*5
:
:
:
:
:
NOTE
A-D CONVERTER
OPTION
USER SUPPLY
TTYCS-4
*1
110/115/220/230VAC,
DPYC-1.5 *1
1φ,50-60Hz RU-3305 *2
SHIPYARD SUPPLY
P
P
1
DPYCY-1.5 *1
100VAC,1φ,50-60Hz
( SHIPYARD SUPPLY )
4
3
2
1
03-2088(6-14P) *4
2
1
14
RW-9600,φ22.1,
J1
RW-4747
15/30/40/50m MAX.100m
J608(TB)
J603(XH)
AD_CLK_C
AD_CLK_H
AD_DATA_C
AD_DATA_H
03-2090(3P)
J5(VH)
BRN 1 J613(TB)
GYRO
GYRO_R2
64P1106A
TX_HV 1
BOARD
TB-801
TB901
3 NC
RED 2 GYRO_R1
J680 チャ BRN
*2
3 NC 2 1 TX_HV
NC
CONVERTER
1 J610(TB) 2 NC
2 アカ 24V_PLUS 1 3 24V_PLUS
J4(VH)
PM ENABLE
PM TRIG
GND
-12V
+12V
PM LEVEL
アオ(太) BLU[B]
5
4
3
2
1
YEL
6
キ 2 GYRO_S2
03-2091(5P) キ
4 MOTOR(+) 3 5 MOTOR(+)
ミドリ GRN 3 ハイ(太) GRY[B]
F.G.
DATA1-C
DATA1-H
ダイ
アカ
チャ
GYRO_S3
SHIFT1-C
SHIFT1-H
*1 5 MOTOR(+) 4
6 MOTOR(+)
5
4
3
2
1
ムラサキ PPL 5
YEL
ORG
RED
BRN
1
2
3
4
5
6
J7(NH)
GYROCOMPASS MOTOR(-) 6 8 MOTOR(-)
J/P922
03-2089(5P) アカ RED
J615(TB)
RF_SPU_D_A 9 クロ BLK 11 RF_SPU_D_A
チャ 1 +12V
RF_SPU_D_B
シロ WHT
10 12 RF_SPU_D_B
空中線部
*5
*4
*3
*2
*1
アカ 2 GND ミドリ(太) GRN[B]
SG 11 13 SG
:
3 -5V
:
:
:
:
アカ(太) RED[B]
注記
PM-31
GND 12 14 GND
RSB-096/097
4 GND
2
ANTENNA UNIT
BRN
PERFORMANCE MONITOR
ダイ
GRN
RED
YEL
ORG
パフォーマンスモニター
オプション
造船所手配
3
2
1
6
5
4
3
2
1
ユーザー手配
J3
J4
NC
NC
GND
VCC
GND
GND
+12V
+12V
03P9342
TB BOARD
XH10P-W-6P XH10P-W-5P-A
コンバータ
-5/-12V
J3 1.5/10/20/
RGBビデオ
J501
DVI-RGB-1
CONVERTOR
RGB VIDEO
DVI1TX2_N 1 30m,φ9
J602 J501/J521 J502/J522
DVI1TX2_P 2
3 KEY_TXD_B 1 1 KEY_TXD_B KEY_TXD_B 1 1 KEY_TXD_B
*2
A_GND
4 KEY_TXD_A 2 2 KEY_TXD_A KEY_TXD_A 2 2 KEY_TXD_A
NC
KEY_RXD_B 3 3 KEY_RXD_B KEY_RXD_B 3 3 KEY_RXD_B
NC 5
6 KEY_RXD_A 4 4 KEY_RXD_A KEY_RXD_A 4 4 KEY_RXD_A
NC
PWR_SW 5 5 PWR_SW PWR_SW 5 5 PWR_SW
03P9229A
J9 NC 7
8 GND 6 6 GND GND 6 6 GND
1 VS NC
最長 100m ( 100mを超える場合はRJB-001が必要 )
*1 8 15
6 GND GND 4 GND GND J507/J527
*2 操作部
操作部
3
8 10 17 J622
C(コモン)端子に接続、他方はH(ホット)端子に接続。
CABLE(75Ω) x 5 GND GND 6 GND DVI1TXD_N
*6 : 交流は両極切りブレーカ(造船所手配)を経由すること
2
RCU-015
RCU-014
SYS_FAIL_C
または OR
DSUB-BNC-1
交流電源の片方がアースに落ちている場合は、そのラインを
CONTROL UNIT
SLB-FRN4-A
11 GND V_SYNC 9 NC 20
CONVERTOR *2
CONTROL UNIT
12 10 21
BNCコネクタコンバータ
BNC CONNECTOR
NC GND NC
13 H_SYNC VCC 11 A_GND 22
14 Y_SYNC GND 12 DVI1TXC_P 23 J605(TB)
15 NC -5_-12V 13 DVI1TXC_N 24 HDG_A 1
P *1
HDG_B 2
TTYCS-1Q
HDG_GND 3 HDG SENSOR
(IEC-61162-2)
*5,*6 J607(TB)
*1 TB1 TB4 TB1 *1
100-120/200-240VAC DPYC-2.5 H LOG_A 1
1 1 1 H P TTYCS-1
1φ, 50-60Hz LOG_B 2 SPEED LOG
C
*7 : CU-200/RPU-013間はクロスケーブル、CU-200/HUB-100間はストレートケーブルを使用
2 2 2 C NC 3 (IEC-61162-1)
3 DVI-D MONITOR
J204
4 1 DVI0TX2_N J606(TB)
*6 *1 5 2 *1
DVI0TX2_P
トランス
440VAC NAV_A 1
DPYC-1.5 6 3 A_GND NAV_B 2 P TTYCS-1
1φ, 50-60Hz 4 NAVIGATOR
コンソール
NC
RU-1803
NC 3 (IEC-61162-1)
RCN-003/004
5
スタンダード
NC
*2
6 NC
TRANSFORMER
7 NC J619(TB)
STANDARD CONSOLE
8 NC ARPA_A 1
*1
TB1 1.3m 9 TTYCS-1
DVI0TX1_N ARPA_B 2 P
4
1 10 DVI0TX1_P
ECDIS
NC 3 (IEC-61162-1)
2 11 A_GND
12 NC
13 NC
14 VCC J601
15
制御部
DVI-D/D GND NC 1
RPU-013
16 RS-232C CABLE
NC RXD 2
J3 SINGLELINK5M,φ7 PC
表示部
17 DVI0TXD_N
1 TXD 3
TMDS_DATA2(-) 18 DVI0TXD_P
2 NC 4
TMDS_DATA2(+) 19 A_GND GND 5
PROCESSOR UNIT
TMDS_DATA2/4_SHIELD 3 20 NC
MONITOR UNIT
6
RS-232C
NC
SCALE
DRAWN
NC 4 21 NC NC 7
DWG.No.
CHECKED
NC 5 22
APPROVED
A_GND NC 8
DDC_CLOCK 6 23 DVI0TXC_P
7 NC 9
DDC_DATA 24 DVI0TXC_N
Nov. 2, '04 NC 8
TMDS_DATA(-) 9
TMDS_DATA(+) 10
DVI-D MONITOR J611(TB)
MU-231CR (FAR-2817/2827)
MU-201CR (FAR-2117/2127)
TMDS_DATA1/3_SHIELD 11 J205
MASS
NC 12 AIS_TD_A 1
1 DVI0TX2_N P
NC 13 AIS_TD_B 2
2 DVI0TX2_P AIS_RD_A 3
+5V_POWER 14 3 P *1
A_GND AIS_RD_B 4
15
Y. Hatai
GND 4 NC 5
TTYCS-4
AIS_GND AIS
C3519-C06- C
HOT_PLUG_DETECT 16 5
TAKAHASHI.T
NC
E. MIYOSHI
kg
TMDS_DATAB(-) 17 6
(IEC-61162-2)
NC
TMDS_DATAB(+) 18 7 NC
TMDS_DATA0/5_SHIELD 19 8 NC J620(TB)
5
NC 20 9 DVI0TX1_N
NC 21 TRK_TD_A 1
10 DVI0TX1_P
TMDS_CLOCK_SHIELD 22 TRK_TD_B 2 *1
11 A_GND TRK_RD_A 3
TMDS_CLOCK(+) 23 12 P TTYCS-1
NC TRK_RD_B 4 TRACK_CONTROL
TMDS_CLOCK(-) 24 13 NC GND 5
14 VCC
(IEC-61162-1)
15 GND
16 NC
*1 17
*1
ア−ス銅板 DVI0TXD_N J612(TB) SHIP'S ALARM
3
2
1
18 DVI0TXD_P
TTYCS-7 SYSTEM
ALARM1_0 1
COPPER STRAP 19 ALARM1_1 2 P
A_GND 船内アラーム
W=50
AC
AC
20
GND
NC ALARM2_0 3 システム
ALARM2_1 4 P
*3 21 NC
DVI CABLE 22 A_GND ALARM3_0 5
EXT. MONITOR ALARM3_1 6 P
23 DVI0TXC_P
24 OPERATOR_FITNESS_0 7
DVI0TXC_N P NR203PF-VVS1.25
HUB-100
OPERATOR_FITNESS_1 8
(8PORTS)
*3 J616(NH) MPS588-C
NAME
TYPE
EXT_ALM_ACK_N 9 P5E-4PTX-BL
名 称
1 GND P 1 TXP
スイッチング ハブ
GND 10
2
LAN
OP_HD_IN 2 TXN
SWITCHING HUB
SYS_FAIL_H 11
3 P
TXN
TXP
GND
NC
RXN
NC
RXP
RXP
NC
NC
SYS_FAIL_C 12 3
NETWORK
4 OP_BP_IN 4 NC
8
7
6
5
4
3
2
1
*2
5 GND 5 NC
6 OP_TRIG_IN 6 RXN
7 GND 7 NC
RW-4864,φ9.5
MASTER RADAR 8 OP_VIDEO_IN 8 NC
J617(NH)
6
相互結線図
1 GND
2 OP_HD_1
3 GND
P5E-4PTX-BL MPS588-C J302
4 OP_BP_1
1 TXP
5 GND
CU-200
2 TXN
6 OP_TRIG_1
MARINE RADAR/ARPA
(FULL-LOG) 8 OP_VIDEO_1
5 NC
CARD I/F UNIT
カード I/F ユニット
*7
J618(NH) 6 RXN
7 NC
INTERCONNECTION DIAGRAM
1 GND
2 8 NC
OP_HD_2
3 GND J614(TB)
4 MJ-A3SPFD J1
OP_BP_2 MJ-A3SPF0015 シロ WHT
+12V 1 1 +12V
*2
5 GND クロ BLK
GND 2 2 GND
SUB DISPLAY2 RW-4864,φ9.5 6 OP_TRIG_2
7 GND 3 FG
(SEMI-LOG)
S - 2
8 OP_VIDEO_2
FAR-2117/2127/2817/2827 (RCN003/004)
D
C
B
A
(空中線部用) FOR ANTENNA UNIT
*5
*4
*3
*2
*1
TPYC-2.5 *1
110VAC,3φ,60Hz RU-5693 *2
:
:
:
:
:
GND
NOTE
TPYC-2.5 *1
IV-8sq. *1
220VAC,3φ,50Hz RU-6522 *2
保護アース PE
200VAC,3φ,50Hz TPYC-2.5 *1
440VAC,3φ,60Hz RU-5466-1 *2
220VAC,3φ,60Hz
OPTION
K2
380VAC,3φ,50Hz TPYC-2.5 *1
1 3φ(U)
440VAC,3φ,60Hz 3 3φ(V)
USER SUPPLY
PSU-007
電源制御部
SHIPYARD SUPPLY
220VAC,3φ,50Hz
220VAC,3φ,60Hz
( SHIPYARD SUPPLY )
440VAC,3φ,60Hz
POWER SUPPLY UNIT
TB1
03-2088(6-14P) J604 DPYC-1.5 *1
2
1
14
13
ANT_12V_ON 1 1 ANT_12V_ON
J1
2 2 GND
GND NC
3φ(W) 9
3φ(V) 6
3φ(U) 4
XK1
03-2090(3P)
GYRO
J5(VH)
64P1106A
BRN 1 GYRO_R2
2
110/115VAC,1φ,
RED GYRO_R1 *1
DPYC-1.5
CONVERTER
BOARD *2
J680 3 NC 220/230VAC,50-60Hz RU-3305 *2
TB BOARD
NC
GYRO_CLK-C
GYRO_CLK-H
GYRO_DATA-C
GYRO_DATA-H
アカ 100VAC,1φ,50-60Hz
TPYCY-2.5
*1
J4(VH)
2
J7(NH)
3 ダイ ORG 1 GYRO_S1
5
4
3
2
1
4 キ YEL 2 GYRO_S2 J613(TB) *4
キ
15/30/40/50m MAX.100m
RW4747
GYROCOMPASS 7 1 TX_HV
03-2089(3P)
03-2091(5P)
チャ BRN
ダイ ORG
アカ RED
YEL
J610(TB) 2 NC
TB-902
3 3φ(W)
2 3φ(V)
1 3φ(U)
*5
*3
*4
*2
*1
1 AD_DATA_H J603(XH) 3 5
P ハイ(太) GRY[B]
2
:
:
:
:
:
-12V
GND
+5V
GND
+12v
4 6
注記
*1 2 AD_DATA_C
5 ムラサキ(太) PPL[B] 7
3 AD_CLK_H
J615(TB)
TTYCS-4 P シロ(太) WHT[B]
5
4
3
2
1
A-D CONVERTER 4 AD_CLK_C 6 8
SPU_RF_D_A 7 アカ RED 9 SPU_RF_D_A
空中線部
BRN
6
5
4
3
2
1
ダイ シロ WHT
造船所手配
オプション
RF_SPU_D_B 10 12 RF_SPU_D_B
RED
GRN
YEL
ORG
SG 11 ミドリ(太) GRN[B] 13 SG
ユーザー手配
アカ(太) RED[B]
6
5
4
3
2
1
14 GND
3
2
1
GND 12
J3
J4
TB-802
NC
NC
J609
GND
VCC
GND
GND
+12V
+12V
IF_VIDEO IF_VIDEO
PM-51
コンバータ
モニター
MONITOR
ANTENNA UNIT RSB-098/099
-5/-12V
RGBビデオ
J3
DVI-RGB-1
CONVERTOR
RGB VIDEO
TB 03P9349
RSB-100/101/102(FOR_45RPM)
PERFORMANCE
DVI1TX2_N 1
パフォーマンス
DVI1TX2_P 2
A_GND 3
*2
NC 4 TOTAL : UP TO 31.5m
NC 5 合計 : 31.5m以下
03P9229A
NC 6 XH10P-W-6P XH10P-W-5P-A
J9 2.3m,φ9
RGB-BUFF基板
NC 7 J602(XH) J501/J521 J502/J522 1.5/10/20/ J501
DVI-RGB変換基板
30m,φ9
*3 1 VS NC 8 KEY_TXD_B 1 1 KEY_TXD_B KEY_TXD_B 1 1 KEY_TXD_B
J2 2 GND DVI1TX1_N 9 2 2
最長 100m ( 100mを超える場合はRJB-001が必要 )
4 NC GND 2 6 GND NC 13 GND 6 6 GND GND 6 6 GND
3
交流は両極切りブレーカ(造船所手配)を経由すること
COAXIAL 7 GND B_VIDEO 5 9 B NC 16 SYS_FAIL_H 9 9 SYS_FAIL_H NC 9 9 NC
CABLE(75Ω) x 5 8 GND GND 6 10 GND DVI1TXD_N 17 10 10 SYS_FAIL_C NC 10 10 NC
SYS_FAIL_C
*2
DSUB-BNC-1
10 GND GND 8 A_GND 19
CONVERTOR *2
11 GND V_SYNC 9 NC 20
SLB-FRN4-A
J507/J527
または
BNCコネクタコンバータ
BNC CONNECTOR
12 NC GND 10 NC 21
操作部
操作部
RCU-015
RCU-014
1
RCU-016
SYS_ACK_C 2 4 SYS_ACK_C
J616(NH)
1 GND J605(TB)
2 OP_HD_IN HDG_A 1
3 GND P *1
HDG_B 2 TTYCS-1Q
4 OP_BP_IN HDG_GND 3 HDG SENSOR
5 GND
6 OP_TRIG_IN
(IEC-61162-2)
7 GND J607(TB)
RW-4864,φ9.5 LOG_A *1
MASTER RADAR 8 OP_VIDEO_IN 1
LOG_B P TTYCS-1
2 SPEED LOG
J617(NH) NC 3 (IEC-61162-1)
1 GND
2 OP_HD_1
4
3 GND J606(TB)
4 OP_BP_1 *1
NAV_A 1
5 GND P TTYCS-1
NAV_B 2 NAVIGATOR
6 OP_TRIG_1 NC 3
SUB DISPLAY1 7 GND (IEC-61162-1)
RW-4864,φ9.5
(FULL-LOG) 8 OP_VIDEO_1
J619(TB)
J618(NH) *1
1 ARPA_A 1 TTYCS-1
GND P
2 ARPA_B 2 ECDIS
OP_HD_2
NC 3 (IEC-61162-1)
3 GND
SCALE
DRAWN
4 OP_BP_2
DWG.No.
CHECKED
5 GND
APPROVED
J601
6 OP_TRIG_2
SHIP'S ALARM SYSTEM
NC 1
船内アラームシステム
MASS
C
2 2 C NC 7
J204 DVI-D MONITOR NC 8
NC 9
C3521-C02- C
1
Y. Hatai
*1 DVI0TX2_N
トランス
2 DVI0TX2_P
TAKAHASHI.T
DPYC-1.5
E. MIYOSHI
440VAC 3 A_GND
kg
RU-1803
2 P
5
6 NC AIS_TD_B
TRANSFORMER
100-230VAC
7 NC AIS_RD_A 3 *1
RCN-001/002
8 NC AIS_RD_B 4 P
SLIM CONSOLE
TTYCS-4
9 DVI0TX1_N AIS_GND 5 AIS
10 DVI0TX1_P (IEC-61162-2)
スリムコンソール
11 A_GND
J620(TB)
制御部
12 NC
TTYCS-1
*1
RPU-013
13 NC TRK_TD_A 1
IV-1.25sq.
*1
14 VCC TRK_TD_B 2 *1
15 GND TRK_RD_A 3
P TTYCS-1
16 NC TRK_RD_B 4
3
2
1
TRACK_CONTROL
TB1 17 DVI0TXD_N GND 5
PROCESSOR UNIT
1.3m (IEC-61162-1)
18 DVI0TXD_P
AC
AC
1
GND
19 A_GND
2 20 NC J612(TB) *1
21 TTYCS-7
NC ALARM1_0 1
VIDEO IN DVI-D DVI-D/D 22 A_GND ALARM1_1 2 P
モニター部
SINGLELINK5M,φ7
(8PORTS)
名 称
P
MONITOR UNIT
2 DVI0TX2_P 4
DDC_CLOCK 6 EXT_ALM_ACK_N 9 シロ/アオ WHT/BLU P NC
3 A_GND 5
DDC_DATA 7 GND 10 P ダイ ORG RXN
6
MU-231CR (FAR-2837S)
MU-201CR (FAR-2137S)
NC 8 4 NC シロ/チャ WHT/BRN
SYS_FAIL_H 11 7 NC
TMDS_DATA(-) 9 5 NC P チャ BRN
6 SYS_FAIL_C 12 8 NC
6
TMDS_DATA(+) 10 NC
相互結線図
TMDS_DATA1/3_SHIELD 11 7 NC
NC 12 8 NC
NC 13 9 DVI0TX1_N
+5V_POWER 14 10 DVI0TX1_P NETWORK
11 A_GND MPS588-C J302
GND 15 P5E-4PTX-BL, 10m,φ6.3
TXP 1 1 TXP
CU-200
12 NC
MARINE RADAR/ARPA
14 VCC RXP 3
TMDS_DATAB(+) 18 NC 4 4 NC
15
CARD I/F UNIT
カード I/F ユニット
TMDS_DATA0/5_SHIELD 19 GND
16 NC NC 5 5 NC
NC 20 RXN 6 6 RXN
INTERCONNECTION DIAGRAM
21 17 DVI0TXD_N
*2
NC NC 7 7 NC
TMDS_CLOCK_SHIELD 22 18 DVI0TXD_P
19 NC 8 8 NC
TMDS_CLOCK(+) 23 1.5m A_GND
TMDS_CLOCK(-) 24 20 NC J614(TB) MJ-A3SPFD J1
FAR-2137S/2837S (RCN001/002)
0.6m 21 NC MJ-A3SPF0015-100,10m,φ6
+12V 1 1 +12V
*3 22 A_GND
GND 2 2 GND
DVI CABLE 23 DVI0TXC_P
*1 3 FG
S - 3
ア−ス銅版 24 DVI0TXC_N
COPPER STRAP
EXT. MONITOR
W=50
D
C
B
A
TPYC-2.5 *1
110VAC,3φ,60Hz RU-5693 *2
TPYC-2.5 *1
(空中線部用) FOR ANTENNA UNIT 220VAC,3φ,50Hz RU-6522 *2
*5
*4
*3
*2
*1
TPYC-2.5 *1
440VAC,3φ,50Hz RU-5466-1 *2
:
:
:
:
:
NOTE
K2
TPYC-2.5 *1
PSU-007
200VAC,3φ,50Hz 1 1 3φ(U)
2 3 3φ(V)
電源制御部
220VAC,3φ,60Hz
3 5 3φ(W)
OPTION
380VAC,3φ,50Hz
TB2
440VAC,3φ,60Hz
POWER SUPPLY UNIT
USER SUPPLY
(高速回転用)FOR HSC(45RPM)
220VAC,3φ,50Hz
1
SHIPYARD SUPPLY
A-D CONVERTER
220VAC,3φ,60Hz
440VAC,3φ,60Hz TB1
( SHIPYARD SUPPLY )
1 ANT_12V_ON
TTYCS-4
2 GND
*1
3φ(W) 9
3φ(V) 6
3φ(U) 4
XK1
P
P
3
2
1
TB3
4
3
2
1
03-2088(6-14P) 110/115VAC,1φ, DPYC-1.5 *1
2
1
14
2 GND
220/230VAC,50-60Hz RU-3305 *2
J1
J608(TB)
J604(TB)
*1
J603(XH)
AD_CLK_C
AD_CLK_H
100VAC,1φ,50-60Hz DPYCY-1.5
TPYCY-2.5
J5(VH)
1 ANT_12V_ON
BRN 1 RW4747
GYRO
GYRO_R2 RW-9600,φ22.1,
64P1106A
TX_HV 1
BOARD
RED 2
*2
J680 3 NC NC
チャ チャ BRN
TB-801
CONVERTER
1
3 NC
アカ 1 TX_HV
J4(VH)
ダイ 1 ダイ(太) ORG[B] 2 NC
03-2091(5P)
ORG GYRO_S1
TB-902
3
3 3φ(W)
2 3φ(V)
1 3φ(U)
キ 24V_PLUS 1 3 24V_PLUS
YEL 2
2 100VAC_C
1 100VAC_H
キ
24V_MINUS 2 4 24V_MINUS
ミドリ アオ(太) BLU[B]
F.G.
DATA1-C
DATA1-H
ダイ
アカ
チャ
*1 5 GYRO_S3 MOTOR(+) 3 5 NC
空中線部
5
SHIFT1-C 4
SHIFT1-H 3
2
1
PPL 5 ムラサキ(太) PPL[B]
YEL
ORG
RED
BRN
7 GYRO_FG MOTOR(-) 5
J7(NH)
GYROCOMPASS 03-2089(5P) シロ(太) WHT[B]
7 NC
MOTOR(-) 6 8 NC
アカ RED
SPU_RF_D_A 7 9 SPU_RF_D_A
ミドリ GRN
2
*3
*5
*4
*1
*2
SPU_RF_D_B 8 クロ BLK 10 SPU_RF_D_B
RF_SPU_D_A 9 11 RF_SPU_D_A
J615(TB)
:
:
:
:
J911
シロ WHT
注記
PM TRIG 5
GND 4
-12V 3
+12V 2
PM LEVEL 1
PM ENABLE 6
3 -5V
RSB-100/101/102(FOR_45RPM)
4 GND TB-802
ミドリ 5 -12V J609(TB)
PM-51
キ IF_VIDEO
モニター
MONITOR
IF_VIDEO
BRN
造船所手配
オプション
ダイ
GRN
RED
YEL
ORG
PERFORMANCE
ユーザー手配
TB 03P9349
パフォーマンス
3
2
1
6
5
4
3
2
1
J3
J4
NC
NC
GND
VCC
GND
GND
+12V
+12V
03P9342
TB BOARD
XH10P-W-6P XH10P-W-5P-A
コンバータ
-5/-12V
J3 1.5/10/20/
RGBビデオ
J501
DVI-RGB-1
CONVERTOR
RGB VIDEO
DVI1TX2_N 1 30m,φ9
2 J602 J501/J521 J502/J522
DVI1TX2_P KEY_TXD_B
3 KEY_TXD_B 1 1 KEY_TXD_B KEY_TXD_B 1 1
*2
A_GND
4 KEY_TXD_A 2 2 KEY_TXD_A KEY_TXD_A 2 2 KEY_TXD_A
NC
5 KEY_RXD_B 3 3 KEY_RXD_B KEY_RXD_B 3 3 KEY_RXD_B
NC
6 KEY_RXD_A 4 4 KEY_RXD_A KEY_RXD_A 4 4 KEY_RXD_A
NC
J9 PWR_SW 5 5 PWR_SW PWR_SW 5 5 PWR_SW
03P9229A
NC 7
1 8 GND 6 6 GND GND 6 6 GND
VS NC
NC GND GND NC
最長 100m ( 100mを超える場合はRJB-001が必要 )
DVI-RGB CONVERSION BOARD
5 NC G_VIDEO 3 7 G VCC 14
*1
6 GND GND 4 8 GND GND 15 J507/J527
*2 操作部
*6 : 交流は両極切りブレーカ(造船所手配)を経由すること
1 SYS_FAIL_H
RCU-016
操作部
SYS_FAIL_C
または OR
交流電源の片方がアースに落ちている場合は、そのラインを
10 GND GND 8 A_GND 19 SYS_ACK_C 2 4 SYS_ACK_C
DSUB-BNC-1
CONTROL UNIT
SLB-FRN4-A
11 GND V_SYNC 9 NC 20
CONVERTOR *2
CONTROL UNIT
C(コモン)端子に接続し、他方はH(ホット)端子に接続します。
12 10 21
BNCコネクタコンバータ
BNC CONNECTOR
NC GND NC
13 H_SYNC VCC 11 A_GND 22
14 Y_SYNC GND 12 DVI1TXC_P 23 J605(TB)
15 NC -5_-12V 13 DVI1TXC_N 24 HDG_A 1
P *1
HDG_B 2
TTYCS-1Q
HDG_GND 3 HDG SENSOR
(IEC-61162-2)
*5,*6 J607(TB)
*1 TB1 TB4 TB1 *1
100-120/200-240VAC LOG_A 1
DPYC-2.5 H 1 H P TTYCS-1
1 1 LOG_B 2 SPEED LOG
*7 : CU-200/RPU-013間はクロスケーブル、CU-200/HUB-100間はストレートケーブルを使用
1φ, 50-60Hz C
2 2 2 C NC 3 (IEC-61162-1)
3 J204 DVI-D MONITOR
*6 4 1 DVI0TX2_N
*1 J606(TB)
トランス
440VAC 5 2 DVI0TX2_P *1
DPYC-1.5 NAV_A 1
1φ, 50-60Hz 3 A_GND P TTYCS-1
6 NAV_B 2
RU-1803
4 NC
NAVIGATOR
NC 3
コンソール
5 NC
(IEC-61162-1)
*2
RCN-003/004
スタンダード
TRANSFORMER
NC
7 NC J619(TB)
4
8 NC *1
STANDARD CONSOLE
TB1 ARPA_A 1
9 DVI0TX1_N ARPA_B 2 P TTYCS-1
1 10 DVI0TX1_P
ECDIS
NC 3 (IEC-61162-1)
2 11 A_GND
12 NC
表示部
13 NC
14 VCC J601
15
制御部
GND 1
DVI-D/D NC
RPU-013
RS-232C CABLE
MONITOR UNIT
16 NC
J3 SINGLELINK5M,φ7 RXD 2 PC
17 DVI0TXD_N
1 TXD 3
TMDS_DATA2(-) 18 DVI0TXD_P
2 NC 4
TMDS_DATA2(+) 19 A_GND
SCALE
DRAWN
GND 5
PROCESSOR UNIT
TMDS_DATA2/4_SHIELD 3 20
DWG.No.
CHECKED
NC
MU-231CR (FR-2837S)
MU-201CR (FR-2137S)
6
RS-232C
NC
APPROVED
NC 4 21 NC
5 NC 7
NC 22 A_GND
6 NC 8
DDC_CLOCK 23
Nov. 4, '04
DVI0TXC_P 9
7 NC
DDC_DATA 24 DVI0TXC_N
NC 8
TMDS_DATA(-) 9
TMDS_DATA(+) 10
J611(TB)
MASS
11 DVI-D MONITOR
TMDS_DATA1/3_SHIELD J205
NC 12 AIS_TD_A 1
1 DVI0TX2_N P
NC 13 AIS_TD_B 2
2
C3521-C03- C
DVI0TX2_P
Y. Hatai
14 AIS_RD_A 3 *1
+5V_POWER 3 A_GND P
AIS_RD_B 4
TAKAHASHI.T
GND 15 TTYCS-4
E. MIYOSHI
4 NC AIS_GND 5 AIS
16
kg
HOT_PLUG_DETECT 5 NC
TMDS_DATAB(-) 17 (IEC-61162-2)
6 NC
TMDS_DATAB(+) 18 7 NC
5
TMDS_DATA0/5_SHIELD 19 8 NC J620(TB)
NC 20 9 DVI0TX1_N
NC 21 TRK_TD_A 1
10 DVI0TX1_P
TMDS_CLOCK_SHIELD 22 TRK_TD_B 2 *1
11 A_GND TRK_RD_A 3
TMDS_CLOCK(+) 23 12 P TTYCS-1
NC TRK_RD_B 4 TRACK_CONTROL
TMDS_CLOCK(-) 24 13 NC GND 5 (IEC-61162-1)
14 VCC
15 GND
16 NC
*1 *1
17 DVI0TXD_N J612(TB) SHIP'S ALARM
ア−ス銅板
3
2
1
18 DVI0TXD_P
TTYCS-7 SYSTEM
ALARM1_0 1
COPPER STRAP 19 A_GND ALARM1_1 2 P
船内アラーム
AC
AC
W=50 20
GND
NC ALARM2_0 3
ALARM2_1 4 P システム
*3 21 NC
DVI CABLE 22 A_GND ALARM3_0 5
ALARM3_1 6 P
EXT. MONITOR 23 DVI0TXC_P
24 OPERATOR_FITNESS_0 7
DVI0TXC_N P NR203PF-VVS1.25
HUB-100
OPERATOR_FITNESS_1 8
(8PORTS)
J616(NH) MPS588-C
EXT_ALM_ACK_N 9 P5E-4PTX-BL
NAME
TYPE
1 GND P
名 称
1 TXP
スイッチング ハブ
GND 10
2 OP_HD_IN
LAN
2 TXN
SWITCHING HUB
SYS_FAIL_H 11
3 P
TXN
TXP
GND
NC
RXN
NC
RXP
RXP
NC
NC
SYS_FAIL_C 12 3
NETWORK
4 OP_BP_IN 4 NC
8
7
6
5
4
3
2
1
*2
5 GND 5 NC
6 OP_TRIG_IN 6 RXN
7 GND 7 NC
RW-4864,φ9.5
MASTER RADAR 8 OP_VIDEO_IN 8 NC
J617(NH)
6
1 GND
相互結線図
2 OP_HD_1
3 GND P5E-4PTX-BL
MPS588-C J302
4 OP_BP_1
1 TXP
5 GND
CU-200
2 TXN
6 OP_TRIG_1
3 RXP
7 GND
MARINE RADAR/ARPA
船舶用レーダー/ARPA
*7
J618(NH) 6 RXN
1 GND 7 NC
2 OP_HD_2 8 NC
INTERCONNECTION DIAGRAM
3 GND
J614(TB) MJ-A3SPFD J1
4 OP_BP_2 MJ-A3SPF0015 シロ WHT
+12V 1 1 +12V
*2
5 GND クロ BLK
6 OP_TRIG_2 GND 2 2 GND
FAR-2137S/2837S (RCN003/004)
(SEMI-LOG)
D
C
B
A
*1
TB901
*5
*4
*3
*2
*1
*8 DPYCY-1.5
1 100VAC_H
PM ENABLE
PM TRIG
GND
-12V
+12V
PM LEVEL
:
:
:
:
:
100VAC,1φ,50-60Hz
NOTE
J911
2 100VAC_C 5
4
3
2
1
6
氷結防止用
*1 3 NC
DE-ICER DPYC-1.5
RSB-103
110/115/220/230VAC, RU-3305 *2
空中線部
OPTION
1
2
3
4
5
6
PM-31
MONITOR
モニター
J/P922
1φ,50-60Hz
ANTENNA UNIT
USER SUPPLY
PERFORMANCE
パフォーマンス
*1
保護アース PE
IV-3.5sq.
WITH DE-ICER
氷結防止あり
1
SHIPYARD SUPPLY
( SHIPYARD SUPPLY )
MOTOR_C 8
MOTOR_C 7
MOTOR_H 6
MOTOR_H 5
GND 9
GND 8
PM-ENABL 7
PM-LEVEL 6
PM-TRIG 5
-12V 4
BP 3
HD 2
+12V 1
NC 11
NC 10
RW-4747
TB801
TB803
NO DE-ICER
A-D CONVERTER
氷結防止なし
TTYCS-4
OR WRJ-9
MAX.30m
MPYCY-19
P
P
*1
4
3
2
1
1
TB803
14
TB804
11 NC
10 NC
3 BP
2 HD
2 NC
J1
9 GND
8 GND
J608(TB)
4 -12V
1 +12V
FR-9-20/30/50(20/30/50m)
J5(VH)
5 PM-TRIG
3 MOTOR_C
1 MOTOR_H
7 PM-ENABL
6 PM-LEVEL
BRN 1
GYRO
GYRO_R2 TX_HV 1 RW-9600,φ22.1,
64P1106A
BOARD
*2
J680 3 NC チャ BRN
チャ 1 TX_HV
CONVERTER
1 J610(TB) 2 NC
2 アカ ダイ(太) ORG[B]
J4(VH)
ダイ ORG 1 GYRO_S1 24V_PLUS 1 3 24V_PLUS
3 キ(太) YEL[B] 4 24V_MINUS
キ YEL 2 GYRO_S2 24V_MINUS 2
2
03-2091(5P) キ
4 アオ(太) BLU[B]
ミドリ GRN 3 MOTOR(+) 3 5 MOTOR(+)
ダイ
アカ
チャ
F.G.
DATA1-C
DATA1-H
*1 5 GYRO_S3
アオ BLU 4 MOTOR(+) 4 ハイ(太) GRY[B] 6 MOTOR(+)
MPYC-7 6 GYRO_T
ムラサキ(太) PPL[B]
5
SHIFT1-C 4
SHIFT1-H 3
2
1
ムラサキ PPL 5 7 MOTOR(-)
YEL
ORG
RED
BRN
GYROCOMPASS 7 GYRO_FG MOTOR(-) 5
J7(NH)
03-2089(5P) MOTOR(-) 6 シロ(太) WHT[B] 8 MOTOR(-)
RTR-081
*3
*5
*1
*4
*2
SPU_RF_D_B 8 ミドリ GRN 10 SPU_RF_D_B
J615(TB)
クロ BLK
:
:
:
:
RF_SPU_D_A 9 11 RF_SPU_D_A
注記
チャ 1 +12V シロ WHT
RF_SPU_D_B 10 12 RF_SPU_D_B
アカ 2 GND ミドリ(太) GRN[B]
-5V
SG 11 13 SG
3 アカ(太) RED[B]
GND GND 12 14 GND
4
TRANSCEIVER UNIT
BRN
造船所手配
オプション
ダイ
GRN
RED
YEL
ORG
ユーザー手配
3
2
1
6
5
4
3
2
1
J3
J4
NC
NC
GND
VCC
GND
GND
+12V
+12V
03P9342
TB BOARD
XH10P-W-6P XH10P-W-5P-A
コンバータ
-5/-12V
*1
J3 1.5/10/20/
RGBビデオ
J501
DVI-RGB-1
CONVERTOR
RGB VIDEO
DVI1TX2_N 1 30m,φ9
2 J602 J501/J521 J502/J522
IV-8sq.
DVI1TX2_P KEY_TXD_B
3 KEY_TXD_B 1 1 KEY_TXD_B KEY_TXD_B 1 1
*2
A_GND
4 KEY_TXD_A 2 2 KEY_TXD_A KEY_TXD_A 2 2 KEY_TXD_A
NC
5 KEY_RXD_B 3 3 KEY_RXD_B KEY_RXD_B 3 3 KEY_RXD_B
NC
6 KEY_RXD_A 4 4 KEY_RXD_A KEY_RXD_A 4 4 KEY_RXD_A
NC
*8 : 船内配電盤では3Aのブレーカを使用
J9 PWR_SW 5 5 PWR_SW PWR_SW 5 5 PWR_SW
03P9229A
NC 7
1 8 GND 6 6 GND GND 6 6 GND
VS NC
5 NC G_VIDEO 3 7 G VCC 14
最長 100m ( 100mを超える場合はRJB-001が必要 )
*1
6 GND GND 4 8 GND GND 15 J507/J527
*2 操作部
操作部
SYS_FAIL_C
C(コモン)端子に接続し、他方はH(ホット)端子に接続
*6 : 交流は両極切りブレーカ(造船所手配)を経由すること
または OR
DSUB-BNC-1
交流電源の片方がアースに落ちている場合は、そのラインを
CONTROL UNIT
SLB-FRN4-A
11 GND V_SYNC 9 NC 20
CONVERTOR *2
CONTROL UNIT
12 10 21
BNCコネクタコンバータ
BNC CONNECTOR
NC GND NC
13 H_SYNC VCC 11 A_GND 22
14 Y_SYNC GND 12 DVI1TXC_P 23 J605(TB)
15 NC -5_-12V 13 DVI1TXC_N 24 HDG_A 1
HDG_B 2 P *1
HDG_GND 3
TTYCS-1Q
HDG SENSOR
(IEC-61162-2)
*5,*6 *1 J607(TB)
TB1 TB4 TB1 *1
100-120/200-240VAC DPYC-2.5 H LOG_A 1
1 1 1 H LOG_B 2 P TTYCS-1
1φ, 50-60Hz C SPEED LOG
2 2 2 C NC 3 (IEC-61162-1)
3 DVI-D MONITOR
*7 : CU-200/RPU-013間はクロスケーブル、CU-200/HUB-100間はストレートケーブルを使用
J204
*6 *1 4 1 DVI0TX2_N
トランス
J606(TB)
440VAC DPYC-1.5 5 2 DVI0TX2_P NAV_A 1
*1
TTYCS-1
RU-1803
1φ, 50-60Hz 3 A_GND NAV_B 2 P
6 NAVIGATOR
4 NC
*2
NC 3 (IEC-61162-1)
4
コンソール
5 NC
TRANSFORMER
RCN-003/004
スタンダード
6 NC
7 NC J619(TB)
8 NC ARPA_A 1
*1
TB1
STANDARD CONSOLE
12 NC
MU-231CR
13 NC
14 VCC J601
15
制御部
GND
MONITOR UNIT
DVI-D/D NC 1
RPU-013
16 RS-232C CABLE
NC RXD 2
J3 SINGLELINK5M,φ7 17
PC
SCALE
DRAWN TMDS_DATA2(-) 1 18
DVI0TXD_N TXD 3
DWG.No.
CHECKED
DVI0TXD_P
APPROVED
2 NC 4
TMDS_DATA2(+) 19 A_GND GND 5
PROCESSOR UNIT
TMDS_DATA2/4_SHIELD 3 20 NC 6
RS-232C
4 NC
NC 21
Nov. 4, '04
NC NC 7
NC 5 22 A_GND
6 NC 8
DDC_CLOCK 23 DVI0TXC_P
7 NC 9
DDC_DATA 24 DVI0TXC_N
MASS NC 8
TMDS_DATA(-) 9
TMDS_DATA(+) 10
DVI-D MONITOR J611(TB)
TMDS_DATA1/3_SHIELD 11 J205
Y. Hatai
C3527-C03- B NC 12 AIS_TD_A 1
1 DVI0TX2_N P
NC 13 AIS_TD_B 2
2
TAKAHASHI.T
DVI0TX2_P AIS_RD_A 3
E. MIYOSHI
+5V_POWER 14 3 P *1
A_GND 4
kg
15 AIS_RD_B TTYCS-4
GND 4 NC AIS_GND 5
HOT_PLUG_DETECT 16 5
AIS
NC
TMDS_DATAB(-) 17 6
(IEC-61162-2)
5
NC
TMDS_DATAB(+) 18 7 NC
TMDS_DATA0/5_SHIELD 19 8 NC J620(TB)
NC 20 9 DVI0TX1_N
NC 21 TRK_TD_A 1
10 DVI0TX1_P
TMDS_CLOCK_SHIELD 22 TRK_TD_B 2 *1
11 A_GND TRK_RD_A 3
TMDS_CLOCK(+) 23 12 P TTYCS-1
NC TRK_RD_B 4 TRACK_CONTROL
TMDS_CLOCK(-) 24 13 NC GND 5
14 VCC
(IEC-61162-1)
15 GND
16 NC
*1 *1
ア−ス銅板 17 DVI0TXD_N J612(TB) SHIP'S ALARM
3
2
1
18 DVI0TXD_P
TTYCS-7 SYSTEM
ALARM1_0 1
COPPER STRAP 19 A_GND ALARM1_1 2 P
船内アラーム
AC
AC
W=50 20
GND
NC ALARM2_0 3
*3 ALARM2_1 4 P システム
21 NC
DVI CABLE 22 A_GND ALARM3_0 5
ALARM3_1 6 P
EXT. MONITOR 23 DVI0TXC_P
24 OPERATOR_FITNESS_0 7
DVI0TXC_N P
HUB-100
OPERATOR_FITNESS_1 8 NR203PF-VVS1.25
(8PORTS)
J616(NH) MPS588-C
NAME
TYPE
EXT_ALM_ACK_N 9 P5E-4PTX-BL
名 称
1 GND P 1 TXP
スイッチング ハブ
GND 10
2 OP_HD_IN
LAN
2 TXN
SWITCHING HUB
SYS_FAIL_H 11
P
6
3
TXN
TXP
GND
NC
RXN
NC
RXP
RXP
NC
NC
SYS_FAIL_C 12 3
NETWORK
4 OP_BP_IN 4 NC
8
7
6
5
4
3
2
1
*2
5 GND 5 NC
6 OP_TRIG_IN 6 RXN
RW-4864,φ9.5 7 GND 7 NC
MASTER RADAR 8 OP_VIDEO_IN 8 NC
J617(NH)
1 GND
相互結線図
2 OP_HD_1
3 GND
P5E-4PTX-BL MPS588-C J302
4 OP_BP_1
1 TXP
5 GND
CU-200
2 TXN
6 OP_TRIG_1
3 RXP
SUB DISPLAY1 RW-4864,φ9.5 7 GND
4 NC
MARINE RADAR/ARPA
(FULL-LOG) 8 OP_VIDEO_1
5 NC
CARD I/F UNIT
カード I/F ユニット
船舶用レーダー/ARPA
6 RXN
*7
J618(NH)
1 GND 7 NC
2 OP_HD_2 8 NC
FAR-2827W (RCN003/004)
3
INTERCONNECTION DIAGRAM
GND J614(TB)
4 MJ-A3SPF0015 MJ-A3SPFD J1
OP_BP_2 シロ WHT
+12V 1 1 +12V
*2
5 GND クロ BLK
GND 2 2 GND
6 OP_TRIG_2
SUB DISPLAY2 RW-4864,φ9.5 7 GND 3 FG
(SEMI-LOG) 8 OP_VIDEO_2
S - 5
D
C
B
A
*5
*4
*3
*2
*1
:
:
:
:
:
NOTE
*8 DPYCY-1.5 *1
氷結防止用 100VAC,1φ,50-60Hz
TB901
DE-ICER DPYC-1.5 *1
110/115/220/230VAC, RU-3305 *2 1 100VAC_H
OPTION
1φ,50-60Hz 2 100VAC_C RSB-105
RSB-104
3 NC
空中線部
200VAC,3φ,50Hz
USER SUPPLY
空中線部モーター用 220VAC,3φ,60Hz J911
1 PM LEVEL
(380/440VAC)
(200/220VAC)
ANTENNA UNIT
SHIPYARD SUPPLY
380VAC,3φ,50Hz
2 +12V
モニター
MONITOR
440VAC,3φ,60Hz 3
1
-12V
PM-51
WITH DE-ICER
氷結防止あり
*1
保護アース PE
IV-3.5sq.
( SHIPYARD SUPPLY )
TPYC(Y)-2.5 *1 4 GND
PERFORMANCE
パフォーマンス
110VAC,3φ,60Hz RU-5693 *2 5
TPYC(Y)-2.5 *1 PM TRIG
220VAC,3φ,50Hz RU-6522 *2 6 PM ENABLE
TPYC(Y)-2.5 *1
440VAC,3φ,50Hz RU-5466-1 *2
TB 03P9349
NC
NC
GND
GND
PM-ENABL
PM-LEVEL
PM-TRIG
-12V
BP
HD
+12V
RW-4747
NO DE-ICER
TB803
氷結防止なし
3φ(W) 3
3φ(V) 2
TTYCS-4 *1 3φ(U) 1
9
8
7
6
5
4
3
2
1
11
10
TB902
A-D CONVERTER
P
P
TPYCY-2.5 *1
03-2088(6-14P) TB911
2
1
14
3 3φ(W)
2 3φ(V)
1 3φ(U)
J603(XH)
AD_CLK_C
AD_CLK_H
TB912
TB803
9 GND
8 GND
AD_DATA_C
AD_DATA_H
03-2090(3P)
J5(VH)
4 -12V
1 +12V
J613(TB)
3 3φ(W)
2 3φ(V)
1 3φ(U)
BRN 1 *4
GYRO
GYRO_R2
64P1106A
TX_HV 1
BOARD
7 PM-ENABL
6 PM-LEVEL
*2
3 NC 2 15/30/40/50m MAX.100m
J680 NC TB-801
チャ チャ BRN
CONVERTER
1 1 TX_HV
2 アカ J610(TB) 2 NC
J4(VH)
3 ダイ ORG 1 GYRO_S1 ダイ(太) ORG[B] 3 24V_PLUS
24V_PLUS 1
キ YEL 2 GYRO_S2 キ(太) YEL[B]
03-2091(5P) キ
4 24V_MINUS 2 4 24V_MINUS
ミドリ GRN 3
F.G.
DATA1-C
DATA1-H
ダイ
アカ
チャ
*1 5 GYRO_S3 MOTOR(+) 3 アオ(太) BLU[B] 5 NC
2
5
SHIFT1-C 4
SHIFT1-H 3
2
1
ムラサキ PPL 5
YEL
ORG
RED
BRN
GYROCOMPASS 7 GYRO_FG ムラサキ(太) PPL[B]
J7(NH)
MOTOR(-) 5 7 NC
03-2089(5P) シロ(太) WHT[B]
MOTOR(-) 6 8 NC
RTR-082
*3
*5
*4
*1
*2
SPU_RF_D_A 7 アカ RED 9 SPU_RF_D_A
送受信部
:
ミドリ GRN
:
:
:
:
SPU_RF_D_B 8 10 SPU_RF_D_B
注記
J615(TB)
クロ BLK 11 RF_SPU_D_A
チャ 1 +12V RF_SPU_D_A 9 シロ WHT
アカ GND RF_SPU_D_B 10 12 RF_SPU_D_B
2 ミドリ(太) GRN[B]
-5V SG 11 13 SG
3 アカ(太) RED[B]
GND GND 12 14 GND
4
TRANSCEIVER UNIT
造船所手配
オプション
IF_VIDEO IF_VIDEO
BRN
ダイ
ユーザー手配
GRN
RED
YEL
ORG
3
2
1
6
5
4
3
2
1
J3
J4
NC
NC
GND
VCC
GND
GND
+12V
+12V
03P9342
TB BOARD
XH10P-W-6P XH10P-W-5P-A
コンバータ
-5/-12V
J3 1.5/10/20/
RGBビデオ
J501
DVI-RGB-1
CONVERTOR
RGB VIDEO
DVI1TX2_N 1 30m,φ9
J602 J501/J521 J502/J522
IV-8sq.
DVI1TX2_P 2
KEY_TXD_B 1 1 KEY_TXD_B KEY_TXD_B 1 1 KEY_TXD_B
3
*2
A_GND
4 KEY_TXD_A 2 2 KEY_TXD_A KEY_TXD_A 2 2 KEY_TXD_A
NC
保護アース PE
*8 : 船内配電盤では3Aのブレーカを使用
6 KEY_RXD_A 4 4 KEY_RXD_A KEY_RXD_A 4 4 KEY_RXD_A
NC
J9 PWR_SW 5 5 PWR_SW PWR_SW 5 5 PWR_SW
03P9229A
NC 7
*3 1 8 GND 6 6 GND GND 6 6 GND
VS NC
交流電源の片方がアースに落ちている場合は、
3 B_VIDEO R_VIDEO 1 5 R NC 12 SYS_FAIL_C 10 10 SYS_FAIL_C NC NC
4 NC GND 2 6 GND NC 13
最長 100m ( 100mを超える場合はRJB-001が必要 )
DVI-RGB CONVERSION BOARD
*1 5 NC G_VIDEO 3 7 G VCC 14
6 GND GND 4 8 GND GND 15 J507/J527
COAXIAL
*2 操作部
操作部
*6 : 交流は両極切りブレーカ(造船所手配)を経由すること
CABLE(75Ω) x 5 8 GND GND 6 10 GND DVI1TXD_N 17 J622 2
RCU-015
RCU-014
SYS_FAIL_C
または OR
DSUB-BNC-1
SLB-FRN4-A
CONTROL UNIT
11 GND V_SYNC 9 NC 20
CONVERTOR *2
CONTROL UNIT
12 10 21
BNCコネクタコンバータ
BNC CONNECTOR
NC GND NC
13 H_SYNC VCC 11 A_GND 22
14 Y_SYNC GND 12 DVI1TXC_P 23 J605(TB)
そのラインをC(コモン)端子に接続し、他方はH(ホット)端子に接続
15 NC -5_-12V 13 DVI1TXC_N 24 HDG_A 1
HDG_B 2 P *1
HDG_GND 3
TTYCS-1Q
HDG SENSOR
(IEC-61162-2)
*5,*6 *1 TB1 TB4 TB1 J607(TB)
100-120/200-240VAC DPYC-2.5 H LOG_A 1
*1
1φ, 50-60Hz 1 1 1 H P TTYCS-1
C LOG_B 2 SPEED LOG
2 2 2 C NC 3 (IEC-61162-1)
*7 : CU-200/RPU-013間はクロスケーブル、CU-200/HUB-100間はストレートケーブルを使用
3 DVI-D MONITOR
*6 J204
*1 4 1
トランス
440VAC DVI0TX2_N J606(TB)
DPYC-1.5 5 2 DVI0TX2_P *1
1φ, 50-60Hz NAV_A 1
RU-1803
6 3 A_GND NAV_B 2 P TTYCS-1
4 NAVIGATOR
コンソール
NC
*2
NC 3 (IEC-61162-1)
RCN-003/004
5 NC
TRANSFORMER
スタンダード
6 NC
4
7 NC J619(TB)
*1
STANDARD CONSOLE
8 NC ARPA_A 1
TB1 9 TTYCS-1
DVI0TX1_N ARPA_B 2 P
1 10 DVI0TX1_P
ECDIS
NC 3 (IEC-61162-1)
2 11 A_GND
表示部
12 NC
MU-231CR
13 NC
14 VCC J601
MONITOR UNIT
15
制御部
DVI-D/D GND NC 1
RPU-013
16 RS-232C CABLE
NC RXD 2
J3 SINGLELINK5M,φ7 17
PC
DVI0TXD_N TXD 3
TMDS_DATA2(-) 1 18 DVI0TXD_P
SCALE
DRAWN TMDS_DATA2(+) 2 19 A_GND
NC 4
DWG.No.
CHECKED
GND 5
PROCESSOR UNIT
APPROVED
TMDS_DATA2/4_SHIELD 20 NC 6
RS-232C
4 NC
NC 21 NC
5 NC 7
NC 22 A_GND 8
Nov. 2, '04
6 NC
DDC_CLOCK 23 DVI0TXC_P
7 NC 9
DDC_DATA 24 DVI0TXC_N
NC 8
TMDS_DATA(-) 9
TMDS_DATA(+) 10
MASS
DVI-D MONITOR J611(TB)
TMDS_DATA1/3_SHIELD 11 J205
NC 12 AIS_TD_A 1
1 DVI0TX2_N P
NC 13 AIS_TD_B 2
Y. Hatai
GND 15 4 TTYCS-4
E.MIYOSHI
NC AIS_GND 5 AIS
16
kg
HOT_PLUG_DETECT 5 NC
TMDS_DATAB(-) 17 6
(IEC-61162-2)
NC
TMDS_DATAB(+) 18 7 NC
5
TMDS_DATA0/5_SHIELD 19 8 NC J620(TB)
NC 20 9 DVI0TX1_N
NC 21 TRK_TD_A 1
10 DVI0TX1_P
TMDS_CLOCK_SHIELD 22 TRK_TD_B 2 *1
11 A_GND TRK_RD_A 3
TMDS_CLOCK(+) 23 12 P TTYCS-1
NC TRK_RD_B 4 TRACK_CONTROL
TMDS_CLOCK(-) 24 13 NC GND 5
14 VCC
(IEC-61162-1)
15 GND
16 NC
*1 *1
17 DVI0TXD_N J612(TB) SHIP'S ALARM
3
2
1
ア−ス銅板 18 DVI0TXD_P
TTYCS-7 SYSTEM
ALARM1_0 1
COPPER STRAP 19 A_GND ALARM1_1 2 P
船内アラーム
AC
AC
20
GND
NC ALARM2_0 3
W=50 ALARM2_1 4 P システム
*3 21 NC
DVI CABLE 22 A_GND ALARM3_0 5
ALARM3_1 6 P
EXT. MONITOR 23 DVI0TXC_P
24 OPERATOR_FITNESS_0 7
DVI0TXC_N P NR203PF-VVS1.25
HUB-100
OPERATOR_FITNESS_1 8
(8PORTS)
J616(NH) MPS588-C
EXT_ALM_ACK_N 9 P5E-4PTX-BL
1 GND P 1 TXP
スイッチング ハブ
GND 10
NAME
TYPE
2 OP_HD_IN
LAN
名 称
2 TXN
SWITCHING HUB
SYS_FAIL_H 11
3 P
TXN
TXP
GND
NC
RXN
NC
RXP
RXP
NC
NC
SYS_FAIL_C 12 3
NETWORK
4 OP_BP_IN NC
6
4
8
7
6
5
4
3
2
1
*2
5 GND 5 NC
6 OP_TRIG_IN 6 RXN
RW-4864,φ9.5 7 GND 7 NC
MASTER RADAR 8 OP_VIDEO_IN 8 NC
J617(NH)
1 GND
2 OP_HD_1
3 GND
相互結線図
2 TXN
6 OP_TRIG_1
3 RXP
SUB DISPLAY1 RW-4864,φ9.5 7 GND
4 NC
(FULL-LOG) 8 OP_VIDEO_1
5 NC
CARD I/F UNIT
カード I/F ユニット
MARINE RADAR/ARPA
*7
J618(NH) 6 RXN
1 7 NC
船舶用レーダー/ARPA
GND
2 OP_HD_2 8 NC
3 GND J614(TB)
4 OP_BP_2 MJ-A3SPFD J1
MJ-A3SPF0015 シロ WHT
INTERCONNECTION DIAGRAM
FAR-2837SW (RCN003/004)
+12V 1 1 +12V
*2
5 GND クロ BLK
GND 2 2 GND
6 OP_TRIG_2
SUB DISPLAY2 RW-4864,φ9.5 7 GND 3 FG
(SEMI-LOG) 8 OP_VIDEO_2
S - 6
D
C
B
A
*1
*5
*4
*3
*2
*1
TB901
PM ENABLE
PM TRIG
GND
-12V
+12V
PM LEVEL
DPYCY-1.5
:
:
:
:
:
J911
NOTE
6
5
4
3
2
1
100VAC,1φ,50-60Hz 1 100VAC_H
氷結防止用 2 100VAC_C
*1 3 NC
1
2
3
4
5
6
DE-ICER
OPTION
DPYC-1.5
PM-31
MONITOR
モニター
J/P922
110/115/220/230VAC, RU-3305 *2
1φ,50-60Hz PERFORMANCE
パフォーマンス
USER SUPPLY
1
SHIPYARD SUPPLY
RSB-103
空中線部
( SHIPYARD SUPPLY )
ANTENNA UNIT
MOTOR_C 8
MOTOR_C 7
MOTOR_H 6
MOTOR_H 5
GND 9
GND 8
PM-ENABL 7
PM-LEVEL 6
PM-TRIG 5
-12V 4
BP 3
HD 2
+12V 1
NC 11
NC 10
TB801
TB803
03-2088(6-14P)
2
1
14
13
OR WRJ-9
J1
MAX,30m
GYRO
03-2090(3P)
J5(VH)
MPYCY-19
64P1106A
*1
BRN 1 GYRO_R2
RED 2 GYRO_R1
導波管 WAVEGUIDE
CONVERTER
BOARD *2
J680 3 NC
NC
GYRO_CLK-C
GYRO_CLK-H
GYRO_DATA-C
GYRO_DATA-H
TB803
アカ
03P9342
J4(VH)
2
TB804
J7(NH)
ダイ 1
11 NC
10 NC
3 BP
2 HD
ORG GYRO_S1
TB BOARD
FR-9-20/30/50(20/30/50m)
2 NC
3
9 GND
8 GND
5
4
3
2
1
4 -12V
1 +12V
4 キ YEL 2 GYRO_S2
5
3 MOTOR_C
1 MOTOR_H
*1 J613(TB) *4
7 PM-ENABL
6 PM-LEVEL
キ
MPYC-7 6 アオ BLU 4 GYRO_T TX_HV 1 RW-9600,φ22.1,
GYROCOMPASS 7 ムラサキ PPL 5 GYRO_FG 15/30/40/50m MAX.100m
NC 2 TB-801
03-2089(3P)
03-2091(5P)
チャ BRN
チャ BRN
ダイ ORG
アカ RED
YEL
1 TX_HV
J610(TB) 2 NC
J608(TB) 24V_PLUS 1 ダイ(太) ORG[B] 3 24V_PLUS
*5
*3
*4
*2
*1
1 AD_DATA_H J603(XH) 24V_MINUS 2 キ(太) YEL[B] 4 24V_MINUS
P
2
:
:
:
:
:
-12V
GND
+5V
GND
+12v
アオ(太) BLU[B]
注記
*1 2 AD_DATA_C MOTOR(+) 3 5 MOTOR(+)
3 AD_CLK_H ハイ(太) GRY[B]
J615(TB)
TTYCS-4 MOTOR(+) 4 6 MOTOR(+)
5
4
3
2
1
P ムラサキ(太) PPL[B]
A-D CONVERTER 4 AD_CLK_C MOTOR(-) 5 7 MOTOR(-)
MOTOR(-) 6 シロ(太) WHT[B] 8 MOTOR(-)
RTR-081
BRN
ダイ
造船所手配
オプション
クロ BLK
RED
RF_SPU_D_A 9 11 RF_SPU_D_A
GRN
YEL
ORG
シロ WHT
ユーザー手配
RF_SPU_D_B 10 12 RF_SPU_D_B
6
5
4
3
2
1
ミドリ(太) GRN[B]
3
2
1
SG 11 13 SG
アカ(太) RED[B]
J3
J4
GND 12 14 GND
TRANSCEIVER UNIT
NC
NC
GND
VCC
GND
GND
+12V
+12V
TB-802
コンバータ
J609
-5/-12V
RGBビデオ
J3 IF_VIDEO IF_VIDEO
DVI-RGB-1
CONVERTOR
RGB VIDEO
DVI1TX2_N 1
DVI1TX2_P 2
A_GND 3
*2
NC 4 TOTAL : UP TO 31.5m
NC 5 合計 : 31.5m以下
03P9229A
NC 6 XH10P-W-6P XH10P-W-5P-A
*1
J9 2.3m,φ9
RGB-BUFF基板
NC 7 J602(XH) J501/J521 J502/J522 1.5/10/20/ J501
DVI-RGB変換基板
30m,φ9
*3 1 VS NC 8 KEY_TXD_B 1 1 KEY_TXD_B KEY_TXD_B 1 1 KEY_TXD_B
IV-8sq.
J2 2 GND DVI1TX1_N 9 2 2
最長 100m ( 100mを超える場合はRJB-001が必要 )
4 NC GND 2 6 GND NC 13 GND 6 6 GND GND 6 6 GND
3
交流は両極切りブレーカ(造船所手配)を経由すること
COAXIAL 7 GND B_VIDEO 5 9 B NC 16 SYS_FAIL_H 9 9 SYS_FAIL_H NC 9 9 NC
CABLE(75Ω) x 5 8 GND GND 6 10 GND DVI1TXD_N 17 10 10 SYS_FAIL_C NC 10 10 NC
VDR SYS_FAIL_C
9 NC H_SYNC 7 DVI1TXD_P 18
DSUB-BNC-1
10 GND GND 8 A_GND 19
CONVERTOR *2
11 GND V_SYNC 9 NC 20 J507/J527
SLB-FRN4-A
BNCコネクタコンバータ
BNC CONNECTOR
または
12 NC GND 10 NC 21
操作部
操作部
1
RCU-016
RCU-015
RCU-014
J622 2
*2
CONTROL UNIT
SYS_ACK_C 2 4 SYS_ACK_C
J616(NH)
1 GND J605(TB)
2 OP_HD_IN HDG_A 1
3 GND P *1
HDG_B 2 TTYCS-1Q
4 OP_BP_IN HDG_GND 3 HDG SENSOR
5 GND
6 OP_TRIG_IN
(IEC-61162-2)
7 GND J607(TB)
RW-4864,φ9.5 LOG_A *1
MASTER RADAR 8 OP_VIDEO_IN 1
LOG_B P TTYCS-1
2 SPEED LOG
J617(NH) NC 3 (IEC-61162-1)
1 GND
2 OP_HD_1
4
3 GND J606(TB)
4 OP_BP_1 *1
NAV_A 1
5 GND P TTYCS-1
NAV_B 2 NAVIGATOR
6 OP_TRIG_1 NC 3
7 GND (IEC-61162-1)
RW-4864,φ9.5
SUB DISPLAY1 8 OP_VIDEO_1
(FULL-LOG) J619(TB)
J618(NH) *1
1 ARPA_A 1 TTYCS-1
GND P
2 ARPA_B 2 ECDIS
OP_HD_2
NC 3 (IEC-61162-1)
3 GND
SCALE
DRAWN
4 OP_BP_2
DWG.No.
CHECKED
5 GND
APPROVED
J601
6 OP_TRIG_2
SHIP'S ALARM SYSTEM
NC 1
船内アラームシステム
7 GND
RS-232C CABLE
*1 *5 SUB DISPLAY2 RW-4864,φ9.5 RXD 2
Feb. 2, '05
8 OP_VIDEO_2
PC
BREAKER (SEMI-LOG) TXD 3
*1 TB1 TB1 NC 4
100-120/200-240VAC DPYC-2.5 H 0.6m GND 5
1φ, 50-60Hz 1 1 H NC 6
MASS
C
2 2 C NC 7
Y. Hatai J204 DVI-D MONITOR NC 8
NC 9
C3527-C02- C
*1 1 DVI0TX2_N
トランス
2 DVI0TX2_P
TAKAHASHI.T
DPYC-1.5
E. MIYOSHI
440VAC 3 A_GND
kg
RU-1803
2 P
5
6 NC AIS_TD_B
TRANSFORMER
100-230VAC
7 NC AIS_RD_A 3 *1
8 NC AIS_RD_B 4 P
TTYCS-4
SLIM CONSOLE
J620(TB)
制御部
12 NC
TTYCS-1
*1
RPU-013
13 NC TRK_TD_A 1
IV-1.25sq.
*1
14 VCC TRK_TD_B 2 *1
15 GND TRK_RD_A 3
P TTYCS-1
16 NC TRK_RD_B 4
3
2
1
TRACK_CONTROL
TB1 17 DVI0TXD_N GND 5
PROCESSOR UNIT
1.3m (IEC-61162-1)
18 DVI0TXD_P
AC
AC
1
GND
19 A_GND
2 20 NC J612(TB) *1
21 TTYCS-7
NC ALARM1_0 1
VIDEO IN DVI-D DVI-D/D 22 A_GND ALARM1_1 2 P
モニター部
SINGLELINK5M,φ7
(8PORTS)
名 称
MU-231CR
P
MONITOR UNIT
2 DVI0TX2_P 4
DDC_CLOCK 6 EXT_ALM_ACK_N 9 シロ/アオ WHT/BLU P NC
3 A_GND 5
DDC_DATA 7 GND 10 P ダイ ORG
6 RXN
NC 8 4 NC シロ/チャ WHT/BRN
SYS_FAIL_H 11 7 NC
TMDS_DATA(-) 9 5 NC P チャ BRN
6 SYS_FAIL_C 12 8 NC
6
TMDS_DATA(+) 10 NC
相互結線図
TMDS_DATA1/3_SHIELD 11 7 NC
NC 12 8 NC
NC 13 9 DVI0TX1_N
+5V_POWER 14 10 DVI0TX1_P NETWORK
11 A_GND MPS588-C J302
GND 15 P5E-4PTX-BL, 10m,φ6.3
TXP 1 1 TXP
CU-200
12 NC
MARINE RADAR/ARPA
TMDS_DATAB(-) 17 13 NC
3 RXP
船舶用レーダー/ARPA
14 VCC RXP 3
TMDS_DATAB(+) 18 NC 4 4 NC
15
CARD I/F UNIT
カード I/F ユニット
TMDS_DATA0/5_SHIELD 19 GND
16 NC NC 5 5 NC
NC 20 RXN 6 6 RXN
INTERCONNECTION DIAGRAM
21 17 DVI0TXD_N
*2
NC NC 7 7 NC
TMDS_CLOCK_SHIELD 22 18 DVI0TXD_P
19 NC 8 8 NC
TMDS_CLOCK(+) 23 1.5m A_GND
TMDS_CLOCK(-) 24 20 NC J614(TB) MJ-A3SPFD J1
0.6m 21 NC MJ-A3SPF0015-100,10m,φ6
+12V 1 1 +12V
*3 22 A_GND
GND 2 2 GND
DVI CABLE 23 DVI0TXC_P
*1 3 FG
ア−ス銅版 24 DVI0TXC_N
S - 7
*5
*4
*3
*2
*1
100VAC,1φ,50-60Hz
2 100VAC_C
:
:
:
:
:
NOTE
DE-ICER DPYC-1.5 *1
RSB-105
110/115/220/230VAC, RU-3305 *2 3 NC RSB-104
空中線部
200VAC,3φ,50Hz 1φ,50-60Hz
空中線部モーター用 220VAC,3φ,60Hz J911
OPTION
1
(380/440VAC)
(200/220VAC)
ANTENNA UNIT
モニター
+12V
MONITOR
440VAC,3φ,60Hz 3
PM-51
-12V
USER SUPPLY
TPYC(Y)-2.5 *1 4
PERFORMANCE
GND
パフォーマンス
TB
110VAC,3φ,60Hz RU-5693 *2 5
1
PM TRIG
SHIPYARD SUPPLY
TPYC(Y)-2.5 *1
220VAC,3φ,50Hz RU-6522 *2 6 PM ENABLE
TPYC(Y)-2.5 *1
( SHIPYARD SUPPLY )
03P9349
440VAC,3φ,50Hz RU-5466-1 *2 NC
NC
GND
GND
PM-ENABL
PM-LEVEL
PM-TRIG
-12V
BP
HD
+12V
TB803
3φ(W) 3
3φ(V) 2
3φ(U) 1
9
8
7
6
5
4
3
2
1
11
10
TB902
03-2088(6-14P)
2
1
14
13
J1
GYRO
03-2090(3P)
J5(VH)
64P1106A
20/30m
MAX,30m
MPYCY-12
BRN 1
TPYCY-2.5
GYRO_R2
*1
RED 2
*1
GYRO_R1
CONVERTER
BOARD *2
LHPX-20D-ASSY
TB911
J680 3 NC
3 3φ(W)
2 3φ(V)
1 3φ(U)
1
NC
GYRO_CLK-C
GYRO_CLK-H
GYRO_DATA-C
GYRO_DATA-H
アカ
03P9342
J4(VH)
2
J7(NH)
ダイ ORG 1 GYRO_S1
TB BOARD
3
11 NC
10 NC
3 BP
2 HD
5
4
3
2
1
TB912
TB803
9 GND
8 GND
4 キ YEL 2 GYRO_S2
4 -12V
1 +12V
*1 5 J613(TB) *4
5 PM-TRIG
キ
アオ BLU 4
7 PM-ENABL
6 PM-LEVEL
03-2091(5P)
チャ BRN
チャ BRN
ダイ ORG
アカ RED
YEL
1 TX_HV
J610(TB) 2 NC
J608(TB) 24V_PLUS 1 ダイ(太) ORG[B] 3 24V_PLUS
*5
*3
*4
*2
*1
1 AD_DATA_H J603(XH) 24V_MINUS 2 キ(太) YEL[B] 4 24V_MINUS
P
2
:
:
:
:
:
-12V
GND
+5V
GND
+12v
アオ(太) BLU[B]
注記
*1 2 AD_DATA_C 3 5
3 AD_CLK_H ハイ(太) GRY[B]
J615(TB)
TTYCS-4 P 4 6
5
4
3
2
1
A-D CONVERTER 4 AD_CLK_C 5 ムラサキ(太) PPL[B] 7
6 シロ(太) WHT[B] 8
RTR-082
BRN
ダイ
造船所手配
オプション
クロ BLK
RED
RF_SPU_D_A 9 11 RF_SPU_D_A
GRN
YEL
ORG
シロ WHT
ユーザー手配
RF_SPU_D_B 10 12 RF_SPU_D_B
6
5
4
3
2
1
ミドリ(太) GRN[B]
3
2
1
SG 11 13 SG
アカ(太) RED[B]
J3
J4
GND 12 14 GND
TRANSCEIVER UNIT
NC
NC
GND
VCC
GND
GND
+12V
+12V
TB-802
コンバータ
J609
-5/-12V
RGBビデオ
J3 IF_VIDEO IF_VIDEO
DVI-RGB-1
CONVERTOR
RGB VIDEO
DVI1TX2_N 1
DVI1TX2_P 2
A_GND 3
*2
NC 4 TOTAL : UP TO 31.5m
NC 5 合計 : 31.5m以下
03P9229A
NC 6 XH10P-W-6P XH10P-W-5P-A
*1
J9 2.3m,φ9
RGB-BUFF基板
NC 7 J602(XH) J501/J521 J502/J522 1.5/10/20/ J501
DVI-RGB変換基板
30m,φ9
*3 1 VS NC 8 KEY_TXD_B 1 1 KEY_TXD_B KEY_TXD_B 1 1 KEY_TXD_B
IV-8sq.
J2 2 GND DVI1TX1_N 9 2 2
最長 100m ( 100mを超える場合はRJB-001が必要 )
4 NC GND 2 6 GND NC 13 GND 6 6 GND GND 6 6 GND
3
交流は両極切りブレーカ(造船所手配)を経由すること
COAXIAL 7 GND B_VIDEO 5 9 B NC 16 SYS_FAIL_H 9 9 SYS_FAIL_H NC 9 9 NC
CABLE(75Ω) x 5 8 GND GND 6 10 GND DVI1TXD_N 17 10 10 SYS_FAIL_C NC 10 10 NC
VDR SYS_FAIL_C
9 NC H_SYNC 7 DVI1TXD_P 18
DSUB-BNC-1
10 GND GND 8 A_GND 19
CONVERTOR *2
11 GND V_SYNC 9 NC 20 J507/J527
SLB-FRN4-A
BNCコネクタコンバータ
BNC CONNECTOR
または
12 NC GND 10 NC 21 1
操作部
操作部
RCU-016
RCU-015
RCU-014
CONTROL UNIT
J616(NH)
1 GND J605(TB)
2 OP_HD_IN HDG_A 1
3 GND P *1
HDG_B 2 TTYCS-1Q
4 OP_BP_IN HDG_GND 3 HDG SENSOR
5 GND
6 OP_TRIG_IN
(IEC-61162-2)
7 GND J607(TB)
RW-4864,φ9.5 LOG_A *1
MASTER RADAR 8 OP_VIDEO_IN 1
LOG_B P TTYCS-1
2 SPEED LOG
J617(NH) NC 3 (IEC-61162-1)
1 GND
2 OP_HD_1
4
3 GND J606(TB)
4 OP_BP_1 *1
NAV_A 1
5 GND P TTYCS-1
NAV_B 2 NAVIGATOR
6 OP_TRIG_1 NC 3
7 GND (IEC-61162-1)
RW-4864,φ9.5
SUB DISPLAY1 8 OP_VIDEO_1
(FULL-LOG) J619(TB)
J618(NH) *1
1 ARPA_A 1 TTYCS-1
GND P
2 ARPA_B 2 ECDIS
OP_HD_2
NC 3 (IEC-61162-1)
3 GND
SCALE
DRAWN
4 OP_BP_2
DWG.No.
CHECKED
5 GND
APPROVED
J601
6 OP_TRIG_2
SHIP'S ALARM SYSTEM
NC 1
船内アラームシステム
7 GND
RS-232C CABLE
*1 *5 RW-4864,φ9.5 RXD 2
Feb. 2, '05
8 OP_VIDEO_2
PC
BREAKER SUB DISPLAY2 TXD 3
*1 TB1 TB1 NC 4
100-120/200-240VAC DPYC-2.5 (SEMI-LOG) H 0.6m 5
GND
1φ, 50-60Hz 1 1 H NC 6
MASS
C
2 2 C NC 7
J204 DVI-D MONITOR NC 8
NC 9
C3528-C03- C
Y. Hatai
*1 1 DVI0TX2_N
トランス
2 DVI0TX2_P
TAKAHASHI.T
DPYC-1.5
E. MIYOSHI
440VAC 3 A_GND
kg
RU-1803
2 P
5
6 NC AIS_TD_B
TRANSFORMER
100-230VAC
RCN-001
7 NC AIS_RD_A 3 *1
8 NC AIS_RD_B 4 P
TTYCS-4
9 DVI0TX1_N AIS_GND 5 AIS
SLIM CONSOLE
10 DVI0TX1_P (IEC-61162-2)
11 A_GND
J620(TB)
制御部
12 NC
TTYCS-1
*1
RPU-013
スリムコンソール
13 NC TRK_TD_A 1
IV-1.25sq.
*1
14 VCC TRK_TD_B 2 *1
15 GND TRK_RD_A 3
P TTYCS-1
16 NC TRK_RD_B 4
3
2
1
TRACK_CONTROL
TB1 17 DVI0TXD_N GND 5
PROCESSOR UNIT
1.3m (IEC-61162-1)
18 DVI0TXD_P
AC
AC
1
GND
19 A_GND
2 20 NC J612(TB) *1
21 TTYCS-7
NC ALARM1_0 1
VIDEO IN DVI-D DVI-D/D 22 A_GND ALARM1_1 2 P
モニター部
SINGLELINK5M,φ7
(8PORTS)
名 称
MU-231CR
P
MONITOR UNIT
2 DVI0TX2_P 4
DDC_CLOCK 6 EXT_ALM_ACK_N 9 シロ/アオ WHT/BLU P NC
3 A_GND 5
DDC_DATA 7 GND 10 P ダイ ORG
6 RXN
NC 8 4 NC シロ/チャ WHT/BRN
SYS_FAIL_H 11 7 NC
TMDS_DATA(-) 9 5 NC P チャ BRN
6 SYS_FAIL_C 12 8 NC
6
TMDS_DATA(+) 10 NC
相互結線図
TMDS_DATA1/3_SHIELD 11 7 NC
NC 12 8 NC
NC 13 9 DVI0TX1_N
+5V_POWER 14 10 DVI0TX1_P NETWORK
11 A_GND MPS588-C J302
GND 15 P5E-4PTX-BL, 10m,φ6.3
TXP 1 1 TXP
CU-200
12 NC
MARINE RADAR/ARPA
14 VCC RXP 3
TMDS_DATAB(+) 18 NC 4 4 NC
15
CARD I/F UNIT
カード I/F ユニット
TMDS_DATA0/5_SHIELD 19 GND
16 NC NC 5 5 NC
NC 20 RXN 6 6 RXN
INTERCONNECTION DIAGRAM
21 17 DVI0TXD_N
*2
NC NC 7 7 NC
TMDS_CLOCK_SHIELD 22 18 DVI0TXD_P
19 NC 8 8 NC
TMDS_CLOCK(+) 23 1.5m A_GND
TMDS_CLOCK(-) 24 20 NC J614(TB) MJ-A3SPFD J1
0.6m 21 NC MJ-A3SPF0015-100,10m,φ6
+12V 1 1 +12V
*3 22 A_GND GND 2 2 GND
23
S - 8
*7
RU-3305
*6
*5
1φ,50-60Hz
*4
*3
*2
*1
氷結防止用
TB901
:
:
:
:
:
:
:
注記
DE-ICER 100VAC,1φ, DPYCY-1.5 *1 1 100VAC_H
*1
PE
440VAC,1φ, DPYC-1.5 トランス 50-60Hz 2 100VAC_C
50-60Hz TRANSFORMER 3 NC
空中線部
RU-1803 *2
IV-3.5sq.
*1
保護アース
RSB-096/097
オプション
造船所手配
*1 *5
ANTENNA UNIT
*3
ユーザー手配
100-120/ *4 BREAKER *1 J1 J603(XH) J613 RW-9600,15/30/40/50m,
1
BOARD
1φ,50-60Hz 1 H NC 2 チャ BRN TX_HV
2 C 03-2090(3P) J5(VH) 11 3 GC_UP J610 2 NC
1 GYRO_R2 12 4 GC_DOWN 24V_PLUS 1 ダイ(太) ORG[B] 3 24V_PLUS
*1 2 13 5 GC_0V 4
J680 GYRO_R1 24V_MINUS 2 キ(太) YEL[B] 24V_MINUS
64P1106A *2
MPYC-7 1 チャ BRN 3 14 6 5
GYROCOMPASS NC GC_5V MOTOR(+) 3 アオ(太) BLU[B] MOTOR(+)
GYRO CONVERTER
2 アカ RED J4(VH) J7(NH) 03-2091(5P) J608 MOTOR(+) 4 ハイ(太) GRY[B] 6 MOTOR(+)
3 ダイ ORG 1 GYRO_S1 DATA1-H 1 チャ BRN 1 AD_DATA_H MOTOR(-) 5 ムラサキ(太) PPL[B] 7 MOTOR(-)
P
4 キ YEL 2 GYRO_S2 DATA1-C 2 アカ RED 2 AD_DATA_C MOTOR(-) 6 シロ(太) WHT[B] 8 MOTOR(-)
PM-31
船内配電盤では3Aのブレーカを使用
P
6 アオ BLU 4 GYRO_T SHIFT1-C 4 キ YEL 4 AD_CLK_C SPU_RF_D_B 8 ミドリ GRN 10 SPU_RF_D_B
7 ムラサキ PPL 5 GYRO_FG FG 5 RF_SPU_D_A 9 クロ BLK 11 RF_SPU_D_A
03-2089(5P) RF_SPU_D_B 10 シロ WHT 12 RF_SPU_D_B
*1 11
SG 11 ミドリ(太) GRN[B] SG
TTYCS-4
PERFORMANCE MONITOR
IF_VIDEO IF_VIDEO
最長 100m ( 100mを超える場合はRJB-001が必要 )
03P9342
*1
TB BOARD
J2 J1 J9 J3
VGA CABLE
交流は両極切りブレーカ(造船所手配)を経由すること
RGB EXT. MONITOR 1 R_VIDEO R_VIDEO 1 5 R 1
2 G_VIDEO GND 2 6 GND 2 TOTAL : UP TO 31.5m
3 B_VIDEO G_VIDEO 3 7 G 合計 : 31.5m以下
4 NC GND 4 8 GND XH10P-W-5P-A
XH10P-W-6P
RW-4747
5 NC B_VIDEO 5 9 B 1.5/10/20/
*1 6 GND GND 6 10 GND 1.5/10/20/
SLB-FRN4-A
CO-AX(75Ω)x5 30m,φ9 30m,φ9
2
03P9229A
8 GND GND 8 4 GND KEY_TXD_B 1 1 KEY_TXD_B KEY_TXD_B 1 1 KEY_TXD_B
DVI-RGB変換基板
DSUB-BNC-1
9 NC V_SYNC 9 1 VS 23 KEY_TXD_A 2 2 KEY_TXD_A KEY_TXD_A 2 2 KEY_TXD_A
CONVERTOR *2
10 GND GND 10 2 GND 24 KEY_RXD_B 3 3 KEY_RXD_B KEY_RXD_B 3 3 KEY_RXD_B
BNCコネクタコンバータ
BNC CONNECTOR
11 GND VCC 11 KEY_RXD_A 4 4 KEY_RXD_A KEY_RXD_A 4 4 KEY_RXD_A
12 NC GND 12 PWR_SW 5 5 PWR_SW PWR_SW 5 5 PWR_SW
13 H_SYNC -5/-12V 13 GND 6 6 GND GND 6 6 GND
CU-200/RPU-013間はクロスケーブル、CU-200/HUB-100間はストレートケーブルを使用
15 NC GND 8 8 GND GND 8 8 GND
SYS_FAIL_H 9 9 SYS_FAIL_H NC 9 9 NC
NC
NC
GND
GND
+12V
+12V
-5/-12V
GND
VCC
J3
J4
10 10
*5
DVI-RGB-1 *2
*4
*3
SYS_FAIL_C 10 10 SYS_FAIL_C NC NC
*2
*1
RGBビデオコンバータ
6
5
4
3
2
1
3
2
1
RGB VIDEO CONVERTOR
:
:
:
:
:
*2
NOTE
RCU-016
操作部 CONTROL UNIT
100-240VAC
1φ,50-60Hz
J507/J527
J615 1 SYS_FAIL_H
チャ BRN 1 +12V
J622 2 SYS_FAIL_C
OPTION
操作部
アカ RED 2 GND
RCU-015
RCU-014
SYS_ACK_H 1 3 SYS_ACK_H
ダイ ORG 3 +5V
SYS_ACK_C 2 4 SYS_ACK_C
キ YEL 4 GND
USER SUPPLY
5
BREAKER
*1 *5
ミドリ GRN -12V
CONTROL UNIT
IV-8sq. *1
SHIPYARD SUPPLY
保護アース PE
( SHIPYARD SUPPLY )
J601
NC 1
RXD 2
DPYC-2.5
*1
TXD 3 *1
3
DVI-D MONITOR NC 4
RS-232C CABLE
2 C
1 H
J3 J204 GND 5 PC
TB1
1
DVI-D/DSINGLELINK5M/10M, 1
TMDS_DATA2(-) DVI0TX2_N NC 6
RS-232C
RPU-013
11 11
NC 3
16 16
MU-231CR (FR-2817/2827)
MU-201CR (FR-2117/2127)
TMDS_DATAB(+) 18 18 DVI0TXD_P J607
TMDS_DATA0/5_SHIELD 19 19 A_GND LOG_A 1
TTYCS-1 SPEED LOG
NC 20 20 NC P
LOG_B 2 (IEC-61162-1)
IV-8sq.
21 21
*1
NC NC NC 3
TMDS_CLOCK_SHIELD 22 22 A_GND
TMDS_CLOCK(+) 23 23 DVI0TXC_P
保護アース PE
*1
4
*6 : USE CROSS CABLE BETWEEN CU-200 & RPU-013 AND STRAIGHT CABLE BETWEEN CU-200 & HUB-100.
2 *1
TRK_TD_B 2
TRK_RD_A 3
TTYCS-1
P TRACK_CONTROL
24 TRK_RD_B 4
GND 5 (IEC-61162-1)
J621
J1 MJ-A3SPFD J614
MJ-A3SPF0015,10m,φ6 シロ WHT RSV1_TD_A 1
SCALE
DRAWN 1 +12V
+12V 1 RSV1_TD_B 2 NOT USED
DWG.No.
CHECKED
クロ BLK
APPROVED
GND 2 2 GND GND 3
CU-200
FG 3 RSV2_TD_A 4
RSV2_TD_B 5
J302 MPS588-C NETWORK
P5E-4PTX-BL,10m,φ6.3 GND 6
Feb. 2, '05
TXP 1 1 TXP
CARD I/F UNIT
カード I/F ユニット
TXN 2 2 TXN *1
J611
3 3 TTYCS-4
MASS
RXP RXP AIS_TD_A 1
*2
NC 4 4 NC P AIS
AIS_TD_B 2
LAN
NC 5 5 NC (IEC-61162-2)
AIS_RD_A 3
RXN 6 *6 6 RXN P
Y. Hatai
AIS_RD_B 4
C3519-C01- K
NC 7 7 NC AIS_GND 5
5
*1
kg
TAKAHASHI. T
E. MIYOSHI
NC 8 8 NC
IV-1.25sq.
*1
LAN CABLE(CAT5) OR J612
*1
MPS588-C FR-FTPC-CY,10/20/30m,φ13 TTYCS-7
ALARM1_0 1 ALARM SYSTEM
TXP 1 シロ/ミドリ WHT/GRN P
P ALARM1_1 2
TXN 2 ミドリ GRN ALARM2_0 3
RXP 3 シロ/ダイ WHT/ORG P
ALARM2_1 4
4 アオ BLU
HUB-100
NC ALARM3_0 5
P P
NC 5 シロ/アオ WHT/BLU ALARM3_1 6
6 ダイ ORG
スイッチング ハブ
RXN OPERATOR_FITNESS_0 7
NC 7 シロ/チャ WHT/BRN P
SWITCHING HUB
OPERATOR_FITNESS_1 8
NC 8 チャ BRN EXT_ALM_ACK_N 9
P
03-163-6001-4
GND 10
*2
AC 1 100-230VAC SYS_FAIL_H 11
AC 2 *1 P
NR203PF-VVS1.25, SYS_FAIL_C 12
*1
GND 3
3.5m, φ8.6
IV-1.25sq.
J616(NH)
RW-4864,φ9.5
GND 1
保護アース PE
MASTER RADAR
OP_HD_IN 2
NAME
TYPE
名 称
GND 3
OP_BP_IN 4
GND 5
OP_TRIG_IN 6
GND 7
OP_VIDEO_IN 8
6
J617(NH)
RW-4864,φ9.5
GND 1 SUB DISPLAY1
相互結線図
OP_HD_1 2
GND 3
(FULL-LOG)
OP_BP_1 4
GND 5
OP_TRIG_1 6
MARINE RADAR/ARPA
GND 7
船舶用レーダー/ARPA
OP_VIDEO_1 8
J618(NH)
RW-4864,φ9.5
INTERCONNECTION DIAGRAM
GND 5
OP_TRIG_2 6
GND 7
FAR-2117/2127/2817/2827 (AC SET)
OP_VIDEO_2 8
D
C
B
A
*6
氷結防止用
*1 TB1
110/115/220/230VAC,
03-2088(6-14P) DPYC-1.5 *1 DE-ICER
2
1
14
13
DPYC-6 1φ,50-60Hz RU-3305 *2
12-24VDC 1 U
PE
*1
2 V DPYCY-1.5 *1
J1
100VAC,1φ,50-60Hz
J5(VH)
03-2090(3P)
保護アース
*1 *4
IV-3.5sq.
BRN 1 GYRO_R2
64P1106A
J613(TB)
GYRO
100/110/115 DPYC-2.5 RED 2
RW-9600,φ22.1,
GYRO_R1 TX_HV 1
BOARD
1 U + 5 J680
*2
200/220/230VAC 3 NC 15/30/40/50m MAX.100m
整流器
2 V - 6 NC 2 TB-801
TB901
チャ BRN 3 NC
RU-3424
1 チャ
1 TX_HV
CONVERTER
1
アカ
RECTIFIER
2
J4(VH)
J610 2 NC
ダイ ORG 1 ダイ(太) ORG[B]
2 100VAC_C
1 100VAC_H
3 GYRO_S1
3 24V_PLUS
PM ENABLE
PM TRIG
GND
-12V
+12V
PM LEVEL
キ YEL 2 24V_PLUS 1
キ
4 GYRO_S2 キ(太) YEL[B]
4 24V_MINUS
J911
24V_MINUS 2
5
4
3
2
1
F.G.
DATA1-C
DATA1-H
5 ミドリ GRN 3 GYRO_S3 アオ(太) BLU[B]
*1 MOTOR(+) 3 5 MOTOR(+)
アオ BLU 4 ハイ(太) GRY[B]
IV-8sq. *1
MPYC-7 6 GYRO_T 6 MOTOR(+)
MOTOR(+)
5
SHIFT1-C 4
SHIFT1-H 3
2
1
4
YEL
03-2091(5P) ダイ ORG
アカ RED
チャ BRN
GYROCOMPASS 7 ムラサキ PPL 5 GYRO_FG ムラサキ(太) PPL[B]
J7(NH)
1
2
3
4
5
6
MOTOR(-) 6 8 MOTOR(-)
アカ RED
SPU_RF_D_A 7 9 SPU_RF_D_A
ミドリ GRN
*2
*1
J608(TB)
*4
*3
*5
J603(XH) SPU_RF_D_B 8 10 SPU_RF_D_B
クロ BLK
:
:
1
:
:
:
AD_DATA_H 9 11 RF_SPU_D_A
NOTE
P RF_SPU_D_A
2 シロ WHT
AD_DATA_C RF_SPU_D_B 10 12 RF_SPU_D_B
空中線部
*1 ミドリ(太) GRN[B]
J615(TB)
3 AD_CLK_H SG 11 13 SG
-12V 5
GND 4
+5V 3
GND 2
+12v 1
TTYCS-4 P アカ(太) RED[B]
PM-31
4 AD_CLK_C 12 14 GND
RSB-096/097
GND
OPTION
A-D CONVERTER
ANTENNA UNIT
ミドリ チャ
キ J609 TB-802
アカ
PERFORMANCE MONITOR
USER SUPPLY
BRN
ダイ IF_VIDEO IF_VIDEO
GRN
パフォーマンスモニター
YEL
RED
ORG
SHIPYARD SUPPLY
3
2
1
6
5
4
3
2
1
J3
J4
TOTAL : UP TO 31.5m
NC
NC
GND
GND
GND
VCC
合計 : 31.5m以下
+12V
+12V
03P9342
TB BOARD
RW-4747
XH10P-W-5P-A
コンバータ
XH10P-W-6P
-5/-12V
J3
RGBビデオ
1.5/10/20/ 1.5/10/20/
DVI-RGB-1
CONVERTOR
RGB VIDEO
2
DVI1TX2_N 1
J602 30m,φ9 J501/J521 J502/J522 30m,φ9 J501
DVI1TX2_P 2
IV-8sq. *1
3 KEY_TXD_B 1 1 KEY_TXD_B KEY_TXD_B 1 1 KEY_TXD_B
A_GND
4 KEY_TXD_A 2 2 KEY_TXD_A KEY_TXD_A 2 2 KEY_TXD_A
NC
5 KEY_RXD_B 3 3 KEY_RXD_B KEY_RXD_B 3 3 KEY_RXD_B
NC
6 KEY_RXD_A 4 4 KEY_RXD_A KEY_RXD_A 4 4 KEY_RXD_A
NC
5 5 5 5
03P9229A
J9 7 PWR_SW PWR_SW PWR_SW PWR_SW
DVI-RGB変換基板
*3 +12V 7 7 +12V +12V 7 7 +12V
J2 9
操作部
8 10 17 J622 2 SYS_FAIL_G
RCU-015
RCU-014
または OR
DSUB-BNC-1
GND GND A_GND
CONTROL UNIT
CONVERTOR *2
11 9 20
CONTROL UNIT
GND V_SYNC NC
SLB-FRN4-A
BNCコネクタコンバータ
BNC CONNECTOR
12 NC GND 10 NC 21
13 H_SYNC VCC 11 A_GND 22
*4
*3
*2
*1
*5
14 Y_SYNC GND 12 DVI1TXC_P 23 J605(TB)
:
:
:
:
:
15 13 24
注記
NC -5_-12V DVI1TXC_N HDG_A 1 *1
P
3
HDG_B 2
TTYCS-1Q
HDG_GND 3 HDG SENSOR
(IEC-61162-2)
J616(NH)
1 GND J607(TB)
オプション
造船所手配
*1
2 OP_HD_IN LOG_A 1
ユーザー手配
P TTYCS-1
3 GND LOG_B 2 SPEED LOG
4 OP_BP_IN NC 3 (IEC-61162-1)
5 GND
*2 6 OP_TRIG_IN
7 GND J606(TB)
RW-4864,φ9.5 *1
MASTER RADAR 8 OP_VIDEO_IN NAV_A 1 TTYCS-1
NAV_B P
2 NAVIGATOR
NC 3 (IEC-61162-1)
J617(NH)
1 GND
2 OP_HD_1 J619(TB)
*6 : 船内配電盤では3Aのブレーカを使用。
CU-200/RPU-013間はクロスケーブル、
*1
3 GND ARPA_A 1 TTYCS-1
4 OP_BP_1 ARPA_B 2 P
ECDIS
5 GND NC 3 (IEC-61162-1)
*2 6 OP_TRIG_1
7 GND
CU-200/HUB-100間はストレートケーブルを使用。
RW-4864,φ9.5
最長 100m ( 100mを超える場合はRJB-001が必要 )
SUB DISPLAY1 8 OP_VIDEO_1
J601
24VDC
100-240VAC
(FULL-LOG)
4
NC 1 RS-232C CABLE
SHIP'S ALARM SYSTEM
船内アラームシステム
J618(NH) RXD 2 PC
*1 1 GND TXD 3
2 OP_HD_2 NC 4
3 GND GND 5
RS-232C
4 OP_BP_2 NC 6
DPYC-1.5
5 GND NC 7
*2 6 OP_TRIG_2 NC 8
RW-4864,φ9.5 7 GND NC 9
8 OP_VIDEO_2
2 V
1 U
SUB DISPLAY2
SCALE
DRAWN
DWG.No.
CHECKED
(SEMI-LOG)
APPROVED
J204 DVI-D MONITOR J611(TB)
1 DVI0TX2_N AIS_TD_A 1
整流器
3 A_GND AIS_RD_A 3
*1
RECTIFIER
P
IV-8sq. *1
4 NC AIS_RD_B 4
TTYCS-4
AIS_GND 5
MASS
5 NC AIS
- 6
+ 5
6 NC (IEC-61162-2)
7 NC
Y. Hatai
8 NC
C3519-C02- J
9 DVI0TX1_N J620(TB)
TAKAHASHI.T
100-230VAC
kg
10
E. MIYOSHI
DVI0TX1_P TRK_TD_A 1
11 TRK_TD_B 2
*1
A_GND *1
5
12 TRK_RD_A 3
*1
NC TTYCS-1
TRK_RD_B 4 P
13 NC
制御部
GND 5
TRACK_CONTROL
RPU-013
14 VCC (IEC-61162-1)
3.5m, φ8.6
15
DPYC-2.5
GND
IV-1.25sq.
*1
16 NC
保護アース PE
NR203PF-VVS1.25,
17 DVI0TXD_N
J612(TB)
*1
18
PROCESSOR UNIT
DVI0TXD_P
3
2
1
TTYCS-7
19 A_GND ALARM1_0 1
P
2 -
1 +
20 NC ALARM1_1 2
AC
AC
TB1
GND
21 NC ALARM2_0 3
03-163-6001-4
22 ALARM2_1 4 P
DVI-D/D A_GND
J3 23 DVI0TXC_P ALARM3_0 5
SINGLELINK5M/10M,φ7 ALARM3_1 6 P *1 LAN CABLE (CAT5) OR
TMDS_DATA2(-) 1 24 DVI0TXC_N
2 OPERATOR_FITNESS_0 7 FR-FTPC-CY, 10/20/30m, φ13
HUB-100
TMDS_DATA2(+) P
(8PORTS)
3 OPERATOR_FITNESS_1 8 MPS588-C
TMDS_DATA2/4_SHIELD EXT_ALM_ACK_N 9
J205 DVI-D MONITOR シロ/ミドリ WHT/GRN
4 TXP
スイッチング ハブ
NC P ミドリ GRN 1
NAME
TYPE
GND 10 P
名 称
5 1 TXN
SWITCHING HUB
NC DVI0TX2_N SYS_FAIL_H 11 2
P シロ/ダイ WHT/ORG
DDC_CLOCK 6 2 DVI0TX2_P 3 RXP
SYS_FAIL_C 12 アオ BLU
DDC_DATA 7 3 A_GND 4 NC
表示部
シロ/アオ WHT/BLU P
*2
NC 8 4 NC 5 NC
ダイ ORG
TMDS_DATA(-) 9 5 NC 6 RXN
シロ/チャ WHT/BRN
TMDS_DATA(+) 10 6 NC 7 NC
チャ BRN
MONITOR UNIT
TMDS_DATA1/3_SHIELD 11 7 NC 8 NC
NC 12 8 NC
6
NC 13 9 DVI0TX1_N
相互結線図
IV-8sq. *1
+5V_POWER 14 10 DVI0TX1_P
GND 15 11 A_GND
NETWORK
HOT_PLUG_DETECT 16 12 NC MPS588-C J302
P5E-4PTX-BL *10m*,φ6.3
TMDS_DATAB(-) 17 13 NC TXP 1 1 TXP
MU-231CR (FR-2817/2827)
MU-201CR (FR-2117/2127)
CU-200
NC 20 16 NC NC 4 4 NC
NC 21 17 DVI0TXD_N NC 5 5 NC
CARD I/F UNIT
カード I/F ユニット
*5
TMDS_CLOCK(+) 23 19 A_GND NC 7 7 NC
*2
TMDS_CLOCK(-) 24 20 NC NC 8 8 NC
21 NC
22 A_GND J614(TB) MJ-A3SPF0015-100,10m,φ6 MJ-A3SPFD J1
*3 シロ WHT
23 DVI0TXC_P +12V 1 1 +12V
DVI CABLE クロ BLK
EXT. MONITOR 24 DVI0TXC_N GND 2 2 GND
3 FG
S - 10
D
C
B
A
D
C
B
A
*1 *5 *7
BREAKER 氷結防止用
*1 110/115/220/230VAC,
TB1 03-2088(6-14P) DPYC-1.5 *1
DPYC-2.5 DE-ICER
2
1
100-120/200-240VAC
14
13
1φ,50-60Hz RU-3305 *2
1 H
1φ, 50-60Hz
PE
DPYCY-1.5 *1
*1
2 C 100VAC,1φ,50-60Hz
J1
03-2090(3P)
J5(VH)
保護アース
*1 *4
IV-3.5sq.
BRN 1 J613(TB)
トランス
GYRO_R2
GYRO
64P1106A
DPYC-1.5 RW-9600,φ22.1,
BOARD
440VAC J680 RED 2 GYRO_R1 TX_HV 1
*2
3 NC 15/30/40/50m MAX.100m
1φ, 50-60Hz NC 2 TB-801
TB901
チャ チャ BRN 3 NC
CONVERTER
1 1 TX_HV
アカ
RU-1803 *2
1
TRANSFORMER
J4(VH)
2 J610(TB) 2 NC
ダイ 1
03-2091(5P)
ORG ダイ(太) ORG[B]
2 100VAC_C
1 100VAC_H
3 GYRO_S1
PM ENABLE
PM TRIG
GND
-12V
+12V
PM LEVEL
キ
GYRO_S2
*5
*6
*4
*3
*2
*1
4
J911
4 24V_MINUS
5
4
3
2
1
24V_MINUS 2
ダイ
チャ
ミドリ GRN 3
F.G.
DATA1-C
DATA1-H
アカ
GYRO_S3 アオ(太) BLU[B]
:
:
:
:
SHIFT1-C
SHIFT1-H
:
:
*1 5 MOTOR(+) 3 5 MOTOR(+)
NOTE
アオ BLU 4 GYRO_T ハイ(太) GRY[B]
MPYC-7 6 MOTOR(+) 4 6 MOTOR(+)
5
4
3
2
1
YEL
ORG
BRN
ムラサキ 5
RED
GYROCOMPASS 7 PPL GYRO_FG ムラサキ(太) PPL[B]
J7(NH)
1
2
3
4
5
6
8 MOTOR(-)
OPTION
MOTOR(-) 6
アカ RED
SPU_RF_D_A 7 9 SPU_RF_D_A
J608(TB) J603(XH) ミドリ GRN 10 SPU_RF_D_B
SPU_RF_D_B 8 クロ BLK
USER SUPPLY
1 AD_DATA_H RF_SPU_D_A 9 11 RF_SPU_D_A
P シロ WHT
*1 2 AD_DATA_C RF_SPU_D_B 10 12 RF_SPU_D_B
空中線部
ミドリ(太) GRN[B]
SHIPYARD SUPPLY
J615(TB)
3 AD_CLK_H SG 11 13 SG
-12V 5
GND 4
+5V 3
GND 2
+12v 1
TTYCS-4 P アカ(太) RED[B]
PM-31
A-D CONVERTER
ANTENNA UNIT
ミドリ チャ
キ J609 TB-802
アカ
PERFORMANCE MONITOR
BRN
ダイ IF_VIDEO IF_VIDEO
パフォーマンスモニター
GRN
YEL
RED
ORG
3
2
1
6
5
4
3
2
1
J3
J4
TOTAL : UP TO 31.5m
NC
NC
GND
VCC
GND
GND
-12V
合計 : 31.5m以下
+12V
+12V
TB BOARD
03P9342
RW-4747
コンバータ
J3 XH10P-W-6P XH10P-W-5P-A
RGBビデオ
1.5/10/20/ 1.5/10/20/
DVI1TX2_N
IV-8sq. *1
1 1 1 1
*2
A_GND
保護アース PE
4 KEY_TXD_A 2 2 KEY_TXD_A KEY_TXD_A 2 2 KEY_TXD_A
NC
5 KEY_RXD_B 3 3 KEY_RXD_B KEY_RXD_B 3 3 KEY_RXD_B
NC
6 KEY_RXD_A 4 4 KEY_RXD_A KEY_RXD_A 4 4 KEY_RXD_A
NC
J9 7 PWR_SW 5 5 PWR_SW PWR_SW 5 5 PWR_SW
RGB-BUFF基板
NC
03P9229A
1 8 GND 6 6 GND GND 6 6 GND
DVI-RGB変換基板
*3 VS NC
J2 9 +12V 7 7 +12V +12V 7 7 +12V
2 GND DVI1TX1_N
3 1 5 12 SYS_FAIL_C 10 10 SYS_FAIL_C NC 10 10 NC
B_VIDEO R_VIDEO R NC
4 NC GND 2 6 GND NC 13
操作部
8 10 17
RCU-016
CABLE(75Ω) x 5 6 1
RCU-015
RCU-014
DSUB-BNC-1
11 9 20
CONTROL UNIT
2 4
CONTROL UNIT
CONVERTOR *2
*3
*4
*1
*5
*2
SLB-FRN4-A
*6
12 10 21
BNCコネクタコンバータ
BNC CONNECTOR
NC GND NC
:
:
:
:
:
:
注記
13 H_SYNC VCC 11 A_GND 22
14 Y_SYNC GND 12 DVI1TXC_P 23 J605(TB)
15 NC -5_-12V 13 DVI1TXC_N 24 HDG_A 1
P *1
3
HDG_B 2 TTYCS-1Q
HDG_GND 3 HDG SENSOR
造船所手配
オプション
(IEC-61162-2)
J616(NH)
ユーザー手配
1 GND J607(TB)
*1
2 OP_HD_IN LOG_A 1 TTYCS-1
3 GND LOG_B 2 P
SPEED LOG
4 OP_BP_IN NC 3 (IEC-61162-1)
5 GND
*2 6 OP_TRIG_IN
7 GND J606(TB)
RW-4864,φ9.5 *1
MASTER RADAR 8 OP_VIDEO_IN NAV_A 1 TTYCS-1
2 P
NAV_B NAVIGATOR
3
*7 : 船内配電盤では3Aのブレーカを使用
NC (IEC-61162-1)
J617(NH)
CU-200/RPU-013間はクロスケーブル、
1 GND
2 OP_HD_1 J619(TB)
*1
3 GND ARPA_A 1 TTYCS-1
4 OP_BP_1 ARPA_B P
CU-200/HUB-100間はストレートケーブルを使用
2 ECDIS
5 GND NC 3 (IEC-61162-1)
最長 100m ( 100mを超える場合はRJB-001が必要 )
*2 6 OP_TRIG_1
RW-4864,φ9.5 7 GND
交流は両極切りブレーカ(造船所手配)を経由すること
SUB DISPLAY1 8 OP_VIDEO_1
J601
SHIP'S ALARM SYSTEM
(FULL-LOG)
船内アラームシステム
4
NC 1 RS-232C CABLE
J618(NH) RXD 2 PC
1 GND TXD 3
2 OP_HD_2 NC 4
3 GND GND 5
4 6
RS-232C
OP_BP_2 NC
5 GND NC 7
*2 6 OP_TRIG_2 NC 8
RW-4864,φ9.5 7 GND NC 9
SUB DISPLAY2 8 OP_VIDEO_2
SCALE
DRAWN
DWG.No.
CHECKED
(SEMI-LOG)
APPROVED
J204 DVI-D MONITOR J611(TB)
1 DVI0TX2_N AIS_TD_A 1
Feb. 2, '05 2 DVI0TX2_P AIS_TD_B 2 P
3 A_GND AIS_RD_A 3 *1
AIS_RD_B 4 P
4 NC TTYCS-4
AIS_GND 5
MASS
5 NC AIS
6 NC (IEC-61162-2)
7 NC
8 NC
Y. Hatai
C3519-C03- K
9 DVI0TX1_N J620(TB)
TAKAHASHI.T
100-230VAC
kg
E. MIYOSHI
10 DVI0TX1_P TRK_TD_A 1
11 A_GND
*1
TRK_TD_B 2 *1
12
5
NC TRK_RD_A 3 TTYCS-1
制御部
13 P
RPU-013
NC TRK_RD_B 4 TRACK_CONTROL
14 VCC GND 5 (IEC-61162-1)
3.5m, φ8.6
15 GND
IV-1.25sq.
*1
16 NC
保護アース PE
NR203PF-VVS1.25,
17 DVI0TXD_N
PROCESSOR UNIT
J612(TB)
*1
18 DVI0TXD_P
3
2
1
TTYCS-7
19 A_GND ALARM1_0 1
20 ALARM1_1 2 P
NC
AC
AC
GND
21 NC ALARM2_0 3
03-163-6001-4
ALARM2_1 4 P
モニター
DVI-D/D 22 A_GND
23 ALARM3_0 5
SINGLELINK5M/10M,φ7 DVI0TXC_P ALARM3_1 6 P
TMDS_DATA2(-) 1 24 DVI0TXC_N
*1 LAN CABLE (CAT5) OR
OPERATOR_FITNESS_0 7
MONITOR *3
TMDS_DATA2(+) OPERATOR_FITNESS_1 8
(8PORTS)
名 称
5 1 2 TXN
SWITCHING HUB
NC DVI0TX2_N SYS_FAIL_H 11
P シロ/ダイ WHT/ORG
DDC_CLOCK 6 2 DVI0TX2_P SYS_FAIL_C 12 3 RXP
アオ BLU
DDC_DATA 7 3 A_GND 4 NC
シロ/アオ WHT/BLU P
*2
NC 8 4 NC 5 NC
ダイ ORG
TMDS_DATA(-) 9 5 NC 6 RXN
シロ/チャ WHT/BRN
TMDS_DATA(+) 10 6 NC 7 NC
チャ BRN
TMDS_DATA1/3_SHIELD 11 7 NC 8 NC
NC 12 8 NC
13 9
6
NC DVI0TX1_N
相互結線図
+5V_POWER 14 10 DVI0TX1_P
GND 15 11 A_GND NETWORK
HOT_PLUG_DETECT 16 12 NC MPS588-C J302
P5E-4PTX-BL *10m*,φ6.3
TMDS_DATAB(-) 17 13 NC TXP 1 1 TXP
CU-200
NC 20 16 NC NC 4 4 NC
NC 21 17 DVI0TXD_N NC 5 5 NC
CARD I/F UNIT
22 18 RXN
*6
23 19 NC
カード I/F ユニット *2
TMDS_CLOCK(+) A_GND NC 7 7
TMDS_CLOCK(-) 24 20 NC NC 8 8 NC
21 NC
22 A_GND J614(TB) MJ-A3SPFD J1
FAR-2117-BB/2127-BB (AC SET)
*3 シロ WHT MJ-A3SPF0015-100,10m,φ6
23 DVI0TXC_P +12V 1 1 +12V
DVI CABLE クロ BLK
EXT. MONITOR 24 DVI0TXC_N GND 2 2 GND
3 FG
S - 11
IV-1.25sq.
D
C
B
A
*6
氷結防止用
*1 110/115/220/230VAC,
TB1 03-2088(6-14P) DPYC-1.5 *1 DE-ICER
2
1
14
13
DPYC-6 1φ,50-60Hz RU-3305 *2
12-24VDC 1 +
PE
*1
DPYCY-1.5 *1
J1
2 - 100VAC,1φ,50-60Hz
J5(VH)
03-2090(3P)
保護アース
*4
IV-3.5sq.
64P1106A
GYRO
100/110/115 DPYC-2.5 BLU 2 GYRO_R1
RW-9600,φ22.1,
1
BOARD
1 U + 5 J680 TX_HV
*2
200/220/230VAC 3 NC 15/30/40/50m MAX.100m
整流器
NC 2
TB901
3 NC
2 V - 6 TB-801
1 ムラサキ チャ BRN
CONVERTER
1 TX_HV
1
アオ
RECTIFIER
J4(VH)
2
RU-3424 *2
GRN J610(TB) 2 NC
2 100VAC_C
1 100VAC_H
24V_PLUS 1 3 24V_PLUS
キ
キ YEL 2
*4
*3
*2
*1
*5
4 GYRO_S2 キ(太) YEL[B]
J911
5
4
3
2
1
24V_MINUS 2 4 24V_MINUS
F.G.
DATA1-C
DATA1-H
ダイ ORG 3
:
:
:
:
:
SHIFT1-C
SHIFT1-H
*1 5 GYRO_S3 アオ(太) BLU[B] 5 MOTOR(+)
NOTE
アカ RED 4 GYRO_T MOTOR(+) 3
6 ハイ(太) GRY[B]
IV-8sq. *1
MPYC-7 6 MOTOR(+)
03-2091(5P)
5
4
3
2
1
YEL
MOTOR(+) 4
ダイ ORG
アカ RED
チャ BRN
チャ BRN 5 GYRO_FG ムラサキ(太) PPL[B]
J7(NH)
GYROCOMPASS 7
1
2
3
4
5
6
OPTION
MOTOR(-) 6 8 MOTOR(-)
アカ RED 9 SPU_RF_D_A
SPU_RF_D_A 7
J608(TB) J603(XH) SPU_RF_D_B 8 ミドリ GRN 10 SPU_RF_D_B
USER SUPPLY
1 AD_DATA_H
クロ BLK 11 RF_SPU_D_A
P RF_SPU_D_A 9
シロ WHT
空中線部
SHIPYARD SUPPLY
ミドリ(太) GRN[B]
J615(TB)
3 AD_CLK_H 13 SG
-12V 5
GND 4
+5V 3
GND 2
+12v 1
TTYCS-4 P SG 11
RSB-096/097
アカ(太) RED[B]
PM-31
ANTENNA UNIT
BRN
ダイ IF_VIDEO IF_VIDEO
パフォーマンスモニター
GRN
YEL
RED
ORG
3
2
1
6
5
4
3
2
1
J3
J4
TOTAL : UP TO 31.5m
NC
NC
GND
VCC
GND
GND
-12V
+12V
+12V
合計 : 31.5m以下
03P9342
RW-4747
コンバータ
XH10P-W-5P-A
TB BOARD
J3 XH10P-W-6P
RGBビデオ
1.5/10/20/
IV-8sq. *1
*2
A_GND 3
4 KEY_TXD_A 2 2 KEY_TXD_A KEY_TXD_A 2 2 KEY_TXD_A
NC
KEY_RXD_B 3 3 KEY_RXD_B KEY_RXD_B 3 3 KEY_RXD_B
*3
*4
*1
*2
*6
*5
NC 5
KEY_RXD_A 4 4 KEY_RXD_A KEY_RXD_A 4 4 KEY_RXD_A
:
:
:
:
:
:
6
注記
NC
J9 PWR_SW 5 5 PWR_SW PWR_SW 5 5 PWR_SW
RGB-BUFF基板
NC 7
03P9229A
8 GND 6 6 GND GND 6 6 GND
DVI-RGB変換基板
*3 1 VS NC
J2 9 +12V 7 7 +12V +12V 7 7 +12V
2 GND DVI1TX1_N
2 J1 4 11 SYS_FAIL_H 9 9 SYS_FAIL_H NC 9 9 NC
G_VIDEO GND A_GND
造船所手配
オプション
3 1 5 12 SYS_FAIL_C 10 10 SYS_FAIL_C NC 10 10 NC
B_VIDEO R_VIDEO R NC
ユーザー手配
4 NC GND 2 6 GND NC 13
8 6 10 17 1
RCU-015
RCU-014
10 8 19 1 3
DSUB-BNC-1
GND GND A_GND SYS_ACK_H SYS_ACK_H
11 9 20 2 4
CONTROL UNIT
CONVERTOR *2
SLB-FRN4-A
BNCコネクタコンバータ
BNC CONNECTOR
12 NC GND 10 NC 21
13 H_SYNC VCC 11 A_GND 22
船内配電盤では3Aのブレーカを使用
14 Y_SYNC GND 12 DVI1TXC_P 23 J605(TB)
15 NC -5_-12V 13 DVI1TXC_N 24 HDG_A 1
P *1
3
HDG_B 2 TTYCS-1Q
HDG_GND 3 HDG SENSOR
(IEC-61162-2)
J616(NH)
最長 100m ( 100mを超える場合はRJB-001が必要 )
1 GND J607(TB)
*1
2 OP_HD_IN LOG_A 1 TTYCS-1
3 2 P
GND LOG_B SPEED LOG
4 OP_BP_IN NC 3 (IEC-61162-1)
5 GND
*2 6 OP_TRIG_IN
7 GND J606(TB)
RW-4864,φ9.5 *1
MASTER RADAR 8 OP_VIDEO_IN NAV_A 1 TTYCS-1
P
NAV_B 2 NAVIGATOR
NC 3 (IEC-61162-1)
J617(NH)
1 GND
2 OP_HD_1 J619(TB)
*1
3 GND ARPA_A 1 TTYCS-1
4 OP_BP_1 ARPA_B P
2 ECDIS
5 GND NC 3 (IEC-61162-1)
CU-200/RPU-013間はクロスケーブル、CU-200/HUB-100間はストレートケーブルを使用
*2 6 OP_TRIG_1
RW-4864,φ9.5 7 GND
SUB DISPLAY1 8 OP_VIDEO_1
J601
SHIP'S ALARM SYSTEM
船内アラームシステム
(FULL-LOG)
4
NC 1 RS-232C CABLE
J618(NH) RXD 2 PC
1 GND TXD 3
2 OP_HD_2 NC 4
3 GND GND 5
RS-232C
4 OP_BP_2 NC 6
5 GND NC 7
*2 6 OP_TRIG_2 NC 8
RW-4864,φ9.5 7 GND NC 9
SUB DISPLAY2 8 OP_VIDEO_2
SCALE
DRAWN
DWG.No.
CHECKED
(SEMI-LOG)
APPROVED
J204 DVI-D MONITOR J611(TB)
1 DVI0TX2_N AIS_TD_A 1
Dec. 2, '04 2 DVI0TX2_P AIS_TD_B 2 P
3 A_GND AIS_RD_A 3
P *1
4 NC AIS_RD_B 4
TTYCS-4
MASS
5 NC AIS_GND 5 AIS
6 NC (IEC-61162-2)
7 NC
Y. Hatai
8 NC
C3519-C04- J
9 DVI0TX1_N J620(TB)
TAKAHASHI.T
100-230VAC
kg
E. MIYOSHI
10 DVI0TX1_P TRK_TD_A 1
*1
11 A_GND TRK_TD_B 2 *1
5
12 NC TRK_RD_A 3
制御部
P TTYCS-1
13
RPU-013
NC TRK_RD_B 4 TRACK_CONTROL
14 VCC GND 5
3.5m, φ8.6
(IEC-61162-1)
15 GND
IV-1.25sq.
*1
16 NC
保護アース PE
NR203PF-VVS1.25,
17 DVI0TXD_N
PROCESSOR UNIT
J612(TB)
*1
18 DVI0TXD_P
3
2
1
TTYCS-7
19 A_GND ALARM1_0 1
20 ALARM1_1 2 P
NC
AC
AC
GND
21 NC ALARM2_0 3
03-163-6001-4
P
モニター
DVI-D/D 22 ALARM2_1 4
A_GND
23 ALARM3_0 5
SINGLELINK5M/10M,φ7 DVI0TXC_P ALARM3_1 6 P
TMDS_DATA2(-) 1 24 DVI0TXC_N
*1 LAN CABLE (CAT5) OR
OPERATOR_FITNESS_0 7
MONITOR *3
TMDS_DATA2(+) OPERATOR_FITNESS_1 8 P
(8PORTS)
P
名 称
5 1 TXN
SWITCHING HUB
NC DVI0TX2_N SYS_FAIL_H 11 2
P シロ/ダイ WHT/ORG
DDC_CLOCK 6 2 DVI0TX2_P SYS_FAIL_C 12 3 RXP
アオ BLU
DDC_DATA 7 3 A_GND 4 NC
シロ/アオ WHT/BLU P
*2
NC 8 4 NC 5 NC
ダイ ORG
TMDS_DATA(-) 9 5 NC 6 RXN
シロ/チャ WHT/BRN
TMDS_DATA(+) 10 6 NC 7 NC
チャ BRN
TMDS_DATA1/3_SHIELD 11 7 NC 8 NC
NC 12 8 NC
6
NC 13 9 DVI0TX1_N
相互結線図
+5V_POWER 14 10 DVI0TX1_P
GND 15 11 A_GND NETWORK
HOT_PLUG_DETECT 16 12 NC MPS588-C J302
P5E-4PTX-BL *10m*,φ6.3
TMDS_DATAB(-) 17 13 NC TXP 1 1 TXP
CU-200
NC 20 16 NC NC 4 4 NC
NC 21 17 DVI0TXD_N NC 5 5 NC
CARD I/F UNIT
*5
TMDS_CLOCK(+) 23 19 A_GND NC 7 7 NC
TMDS_CLOCK(-) 24 20 NC NC 8 8 NC
21 NC
22 J614(TB) MJ-A3SPFD J1
FAR-2117-BB/2127-BB (DC SET)
*3 A_GND MJ-A3SPF0015-100,10m,φ6
23 シロ WHT
DVI0TXC_P +12V 1 1 +12V
DVI CABLE クロ BLK
EXT. MONITOR 24 DVI0TXC_N GND 2 2 GND
3 FG
S - 12
IV-1.25sq.
D
C
B
A
(空中線部用) FOR ANTENNA UNIT
*5
*4
*3
*2
*1
TPYC-2.5 *1
110VAC,3φ,60Hz RU-5693 *2
:
:
:
:
:
GND
NOTE
TPYC-2.5 *1
220VAC,3φ,50Hz RU-6522 *2
200VAC,3φ,50Hz TPYC-2.5 *1
440VAC,3φ,50Hz RU-5466-1 *2
220VAC,3φ,60Hz
OPTION
K2
380VAC,3φ,50Hz TPYC-2.5 *1
1 3φ(U)
440VAC,3φ,60Hz 3 3φ(V)
USER SUPPLY
PSU-007
電源制御部
220VAC,3φ,50Hz
SHIPYARD SUPPLY
220VAC,3φ,60Hz
( SHIPYARD SUPPLY )
440VAC,3φ,60Hz
POWER SUPPLY UNIT
*1 *5
TB1
BREAKER
*1 TB1 03-2088(6-14P) J604(TB) DPYC-1.5 *1
2
1
14
13
100-120/200-240VAC DPYC-2.5 +12V 1 1 ANT_12V_ON
J1
1 H ANT ON N 2 2 GND
1φ, 50-60Hz
2 C 氷結防止用
3φ(W) 9
3φ(V) 6
3φ(U) 4
XK1
03-2090(3P)
GYRO
J5(VH)
64P1106A
*1 BRN 1 DE-ICER *7
トランス
GYRO_R2 110/115VAC,1φ,
DPYC-1.5 RED 2 GYRO_R1 *1
DPYC-1.5
CONVERTER
440VAC
BOARD *2
RU-1803
J680
03P9342
*2
TRANSFORMER
TB BOARD
アカ 100VAC,1φ,50-60Hz
NC
GYRO_CLK-C
GYRO_CLK-H
GYRO_DATA-C
GYRO_DATA-H
2
*1
J4(VH)
J7(NH)
RW-4747
3 ダイ ORG 1 GYRO_S1
5
4
3
2
1
4 キ YEL 2 GYRO_S2 J613(TB) *4
キ
6 アオ BLU 4 GYRO_T NC 2 15/30/40/50m MAX.100m TB-801
MPYC-7
7 ムラサキ PPL 5 GYRO_FG チャ BRN
3 NC
GYROCOMPASS 1 TX_HV
03-2089(3P)
03-2091(5P)
チャ BRN
ダイ ORG
アカ RED
YEL
J610(TB) 2 NC
TB-902
ダイ(太) ORG[B]
3 3φ(W)
2 3φ(V)
1 3φ(U)
24V_PLUS 1 3 24V_PLUS
2 100VAC_C
1 100VAC_H
*3
*5
*4
*1
*2
1 AD_DATA_H J603(XH) 3 5
P ハイ(太) GRY[B]
2
:
:
:
:
2 AD_DATA_C 4 6
注記
*1 ムラサキ(太) PPL[B]
3 AD_CLK_H 5 7
J615(TB)
TTYCS-4 P シロ(太) WHT[B]
-12V 5
GND 4
+5V 3
GND 2
+12v 1
A-D CONVERTER 4 AD_CLK_C 6 8
SPU_RF_D_A 7 アカ RED 9 SPU_RF_D_A
空中線部
BRN
PM TRIG 5
GND 4
-12V 3
+12V 2
PM LEVEL 1
シロ WHT
PM ENABLE 6
ダイ RF_SPU_D_B 10 12 RF_SPU_D_B
造船所手配
オプション
RED
GRN
YEL
ORG
SG 11 ミドリ(太) GRN[B] 13 SG
ユーザー手配
アカ(太) RED[B]
6
5
4
3
2
1
GND 12 14 GND
3
2
1
J3
J4
TB-802
NC
NC
J609
GND
VCC
GND
GND
+12V
+12V
IF_VIDEO IF_VIDEO
PM-51
コンバータ
モニター
MONITOR
-5/-12V
ANTENNA UNIT RSB-098/099
RGBビデオ
J3
DVI-RGB-1
CONVERTOR
RGB VIDEO
TB 03P9349
RSB-100/101/102(FOR_45RPM)
DVI1TX2_N 1
PERFORMANCE
パフォーマンス
DVI1TX2_P 2
IV-8sq. *1
A_GND 3
保護アース PE
*2
NC 4 TOTAL : UP TO 31.5m
NC 5 合計 : 31.5m以下
03P9229A
*7 : 船内配電盤では3Aのブレーカを使用
NC 6 XH10P-W-6P XH10P-W-5P-A
J9 NC 7 J602(XH) 1.5/10/20/ 1.5/10/20/
J501/J521 J502/J522 J501
RGB-BUFF基板
DVI-RGB変換基板
30m,φ9 30m,φ9
*3 1 VS NC 8 KEY_TXD_B 1 1 KEY_TXD_B KEY_TXD_B 1 1 KEY_TXD_B
J2 2 GND DVI1TX1_N 9 KEY_TXD_A 2 2 KEY_TXD_A KEY_TXD_A 2 2 KEY_TXD_A
1 R_VIDEO 3 HS DVI1TX1_P 10
*1
最長 100m ( 100mを超える場合はRJB-001が必要 )
4 NC GND 2 6 GND NC 13 GND 6 6 GND GND 6 6 GND
7
3
交流は両極切りブレーカ(造船所手配)を経由すること
COAXIAL 7 GND B_VIDEO 5 9 B NC 16 SYS_FAIL_H 9 9 SYS_FAIL_H NC 9 9 NC
CABLE(75Ω) x 5 8 GND GND 10 GND DVI1TXD_N 17
(氷結防止あり w/DE-ECER)
6 SYS_FAIL_C 10 10 SYS_FAIL_C NC 10 10 NC
VDR
*2
9 NC H_SYNC 7 DVI1TXD_P 18
DSUB-BNC-1
10 GND GND 8 A_GND 19
CONVERTOR *2
11 GND V_SYNC 9 NC 20
SLB-FRN4-A
J507/J527
または
BNCコネクタコンバータ
BNC CONNECTOR
12 NC GND 10 NC 21
操作部
操作部
1 SYS_FAIL_H
RCU-015
RCU-014
13 11 22
RCU-016
14 12 23 J622 2 SYS_FAIL_C
Y_SYNC GND DVI1TXC_P
15 13 24 SYS_ACK_H 1 3 SYS_ACK_H
NC -5_-12V DVI1TXC_N
2
CONTROL UNIT
4 SYS_ACK_C
CONTROL UNIT
SYS_ACK_C
J616(NH)
1 GND J621(TB)
J605(TB)
2 OP_HD_IN HDG_A 1
*6 : CU-200/RPU-013間はクロスケーブル、CU-200/HUB-100間はストレートケーブルを使用
3 GND P *1
HDG_B 2 TTYCS-1Q
4 OP_BP_IN HDG_GND 3 HDG SENSOR
5 GND
6
(IEC-61162-2)
*2 OP_TRIG_IN
7 GND J607(TB)
RW-4864,φ9.5 LOG_A *1
MASTER RADAR 8 OP_VIDEO_IN 1
LOG_B P TTYCS-1
2 SPEED LOG
NC 3 (IEC-61162-1)
J617(NH)
1 GND
4
2 OP_HD_1 J606(TB)
*1
3 GND NAV_A 1
P TTYCS-1
4 OP_BP_1 NAV_B 2 NAVIGATOR
5 GND NC 3 (IEC-61162-1)
*2 6 OP_TRIG_1
7 GND
RW-4864,φ9.5 J619(TB)
SUB DISPLAY1 8 OP_VIDEO_1 *1
ARPA_A 1 TTYCS-1
(FULL-LOG) 2 P
ECDIS
ARPA_B
J618(NH) NC 3 (IEC-61162-1)
1 GND
SCALE
DRAWN
2 OP_HD_2
DWG.No.
CHECKED
J601
APPROVED
3 GND
SHIP'S ALARM SYSTEM
4 NC 1 RS-232C CABLE
船内アラームシステム
OP_BP_2
5 RXD 2 PC
Feb. 2, '05
GND
*2 6 OP_TRIG_2 TXD 3
7 GND NC 4
RW-4864,φ9.5 GND 5
SUB DISPLAY2 8 OP_VIDEO_2
NC 6
MASS
100-240VAC
(SEMI-LOG) NC 7
J204 DVI-D MONITOR NC 8
9
Y. Hatai
1 NC
C3521-C01- H
DVI0TX2_N
2 DVI0TX2_P
TAKAHASHI.T
3 A_GND
E. MIYOSHI
kg
4 NC J611(TB)
5 NC AIS_TD_A 1
*1 *5
BREAKER
6 NC AIS_TD_B 2 P
5
100-230VAC
7 NC AIS_RD_A 3 *1
P
*1
8 NC AIS_RD_B 4 TTYCS-4
*1
J620(TB)
3.5m, φ8.6
12 NC
制御部
RPU-013
2
1
13 NC TRK_TD_A 1
IV-1.25sq.
*1
14 VCC TRK_TD_B 2
NR203PF-VVS1.25,
保護アース PE
*1
TB1
15 GND TRK_RD_A 3
P TTYCS-1
16 NC TRK_RD_B 4 TRACK_CONTROL
3
2
1
03-163-6002-1
17 DVI0TXD_N GND 5
PROCESSOR UNIT
(IEC-61162-1)
18 DVI0TXD_P
AC
AC
GND
19 A_GND
20 J612(TB) *1
NC
21 TTYCS-7
NC ALARM1_0 1
VIDEO IN DVI-D DVI-D/D 22 A_GND ALARM1_1 2 P
モニター部
NAME
TYPE
(8PORTS)
名 称
MONITOR UNIT
NC 8 6 シロ/チャ WHT/BRN 7 NC
NC SYS_FAIL_H 11
TMDS_DATA(-) 9 P チャ BRN NC
7 NC SYS_FAIL_C 12 8
6
TMDS_DATA(+) 10
IV-8sq. *1
8 NC
相互結線図
TMDS_DATA1/3_SHIELD 11 9 DVI0TX1_N
保護アース PE
USER SUPPLY FOR FAR-2137S-BB
NC 12 10 DVI0TX1_P
NC 13 11 A_GND
+5V_POWER 14 NETWORK MPS588-C J302
12 NC
GND 15 P5E-4PTX-BL *10m*,φ6.3
13 NC TXP 1 1 TXP
CU-200
MARINE RADAR/ARPA
TMDS_DATAB(+) 18 16 NC NC 4 4 NC
CARD I/F UNIT
カード I/F ユニット
TMDS_DATA0/5_SHIELD 19 17 DVI0TXD_N NC 5 5 NC
NC 20 18 DVI0TXD_P RXN 6 6 RXN
INTERCONNECTION DIAGRAM
*6
NC 21
*2
7 NC
FAR-2137S/2837S/2837S-BB
19 A_GND NC 7
TMDS_CLOCK_SHIELD 22 20 NC NC 8 8 NC
TMDS_CLOCK(+) 23 21 NC
TMDS_CLOCK(-) 24 22 A_GND J614(TB) MJ-A3SPFD J1
*3 シロ WHT MJ-A3SPF0015-100,10m,φ6
23 DVI0TXC_P +12V 1 クロ BLK
1 +12V
DVI CABLE GND 2 2 GND
EXT. MONITOR 24 DVI0TXC_N
3 FG
S - 13
IV-1.25sq.
D
C
B
A
*1
TB901
*7 DPYCY-1.5
*5
*4
*3
*2
*1
1 100VAC_H
PM ENABLE
PM TRIG
GND
-12V
+12V
100VAC,1φ,50-60Hz PM LEVEL
:
:
:
:
:
J911
2 100VAC_C
NOTE
5
4
3
2
1
6
氷結防止用
*1 3 NC
DE-ICER DPYC-1.5
RSB-103
110/115/220/230VAC, RU-3305 *2
空中線部
1
2
3
4
5
6
OPTION
PM-31
MONITOR
モニター
J/P922
1φ,50-60Hz
ANTENNA UNIT
PERFORMANCE
パフォーマンス
USER SUPPLY
*1
保護アース PE
IV-3.5sq.
WITH DE-ICER
氷結防止あり
1
SHIPYARD SUPPLY
( SHIPYARD SUPPLY )
MOTOR_C 8
MOTOR_C 7
MOTOR_H 6
MOTOR_H 5
GND 9
GND 8
PM-ENABL 7
PM-LEVEL 6
PM-TRIG 5
-12V 4
BP 3
HD 2
+12V 1
NC 11
NC 10
RW-4747
TB801
TB803
NO DE-ICER
氷結防止なし
*1 *5
BREAKER
*1 TB1 03-2088(6-14P)
2
1
14
13
100-120/200-240VAC DPYC-2.5
J1
1 H
1φ, 50-60Hz
MAX,30m
2 C
OR WRJ-9
MPYCY-19
14-19:
03-2090(3P)
GYRO
J5(VH)
64P1106A
9
8
7
6
5
4
3
2
1
13
12
11
10
*1
NOT USED
*1 BRN 1
トランス
GYRO_R2
BOARD *2
RU-1803
導波管 WAVEGUIDE
*2
TRANSFORMER
アカ
NC
GYRO_CLK-C
GYRO_CLK-H
GYRO_DATA-C
TB803
GYRO_DATA-H
2
03P9342
J4(VH)
TB804
J7(NH)
ダイ ORG 1
11 NC
10 NC
3 BP
2 HD
GYRO_S1
TB BOARD
2 NC
5
4
3
2
1
YEL
4 -12V
1 +12V
4 キ 2 GYRO_S2
FR-9-20/30/50(20/30/50m)
5 ミドリ GRN 3 GYRO_S3
5 PM-TRIG
J613(TB) *4
3 MOTOR_C
1 MOTOR_H
*1
7 PM-ENABL
6 PM-LEVEL
キ
MPYC-7 6 アオ BLU 4 GYRO_T TX_HV 1 RW-9600,φ22.1,
GYROCOMPASS 7 ムラサキ PPL 5 GYRO_FG 15/30/40/50m MAX.100m
NC 2 TB-801
03-2089(3P) チャ BRN
03-2091(5P)
チャ BRN
ダイ ORG
アカ RED
YEL
1 TX_HV
J610(TB) 2 NC
*3
*5
*4
*1
*2
J608(TB) ダイ(太) ORG[B] 3 24V_PLUS
24V_PLUS 1
2
:
:
:
:
注記
1 AD_DATA_H J603(XH) 24V_MINUS 2 キ(太) YEL[B] 4 24V_MINUS
P アオ(太) BLU[B]
*1 2 AD_DATA_C MOTOR(+) 3 5 MOTOR(+)
3 AD_CLK_H ハイ(太) GRY[B] 6 MOTOR(+)
J615(TB)
TTYCS-4 P MOTOR(+) 4
-12V 5
GND 4
+5V 3
GND 2
+12v 1
A-D CONVERTER 4 AD_CLK_C MOTOR(-) 5 ムラサキ(太) PPL[B] 7 MOTOR(-)
MOTOR(-) 6 シロ(太) WHT[B] 8 MOTOR(-)
RTR-081
造船所手配
オプション
キ アカ SPU_RF_D_B 8 ミドリ GRN 10 SPU_RF_D_B
BRN
ユーザー手配
ダイ クロ BLK
RED
RF_SPU_D_A 9 11 RF_SPU_D_A
GRN
YEL
ORG
RF_SPU_D_B 10 シロ WHT 12 RF_SPU_D_B
6
5
4
3
2
1
ミドリ(太) GRN[B]
3
2
1
SG 11 13 SG
アカ(太) RED[B]
J3
J4
GND 12 14 GND
TRANSCEIVER UNIT
NC
NC
GND
VCC
GND
GND
+12V
+12V
TB-802
コンバータ
J609
IF_VIDEO
-5/-12V
RGBビデオ
J3 IF_VIDEO
DVI-RGB-1
CONVERTOR
RGB VIDEO
DVI1TX2_N 1
DVI1TX2_P 2
IV-8sq. *1
A_GND 3
保護アース PE
*2
NC 4 TOTAL : UP TO 31.5m
*7 : 船内配電盤では3Aのブレーカを使用
NC 5 合計 : 31.5m以下
03P9229A
NC 6 XH10P-W-6P XH10P-W-5P-A
*1
J9 NC 7 1.5/10/20/ 1.5/10/20/
J602(XH) J501/J521 J502/J522 J501
RGB-BUFF基板
DVI-RGB変換基板
30m,φ9 30m,φ9
*3 1 VS NC 8 KEY_TXD_B 1 1 KEY_TXD_B KEY_TXD_B 1 1 KEY_TXD_B
IV-8sq.
最長 100m ( 100mを超える場合はRJB-001が必要 )
3 B_VIDEO R_VIDEO 1 5 R NC 12 PWR_SW 5 5 PWR_SW PWR_SW 5 5 PWR_SW
DVI-RGB CONVERSION BOARD
3
交流は両極切りブレーカ(造船所手配)を経由すること
*1 6 GND GND 4 8 GND GND 15 GND 8 8 GND GND 8 8 GND
COAXIAL 7 GND B_VIDEO 5 9 B NC 16 SYS_FAIL_H 9 9 SYS_FAIL_H NC 9 9 NC
CABLE(75Ω) x 5 8 GND GND 6 10 GND DVI1TXD_N 17 10 10 SYS_FAIL_C NC 10 10 NC
VDR SYS_FAIL_C
9 NC H_SYNC 7 DVI1TXD_P 18
DSUB-BNC-1
10 GND GND 8 A_GND 19
CONVERTOR *2
11 GND V_SYNC 9 NC 20
J507/J527
SLB-FRN4-A
または
BNCコネクタコンバータ
BNC CONNECTOR
12 NC GND 10 NC 21
操作部
操作部
1 SYS_FAIL_H
RCU-015
RCU-014
13 11 22
RCU-016
J622 2 SYS_FAIL_C
*2
2 4 SYS_ACK_C
CONTROL UNIT
SYS_ACK_C
J616(NH)
*6 : CU-200/RPU-013間はクロスケーブル、CU-200/HUB-100間はストレートケーブルを使用
1 GND J605(TB)
2 OP_HD_IN HDG_A 1
3 GND P *1
HDG_B 2 TTYCS-1Q
4 OP_BP_IN HDG_GND 3 HDG SENSOR
5 GND
6
(IEC-61162-2)
*2 OP_TRIG_IN
7 GND J607(TB)
RW-4864,φ9.5 LOG_A *1
MASTER RADAR 8 OP_VIDEO_IN 1
LOG_B P TTYCS-1
2 SPEED LOG
NC 3 (IEC-61162-1)
J617(NH)
4
1 GND
2 OP_HD_1 J606(TB)
*1
3 GND NAV_A 1
P TTYCS-1
4 OP_BP_1 NAV_B 2 NAVIGATOR
5 GND NC 3 (IEC-61162-1)
*2 6 OP_TRIG_1
7 GND
RW-4864,φ9.5 J619(TB)
SUB DISPLAY1 8 OP_VIDEO_1 *1
ARPA_A 1 TTYCS-1
(FULL-LOG) 2 P
ECDIS
ARPA_B
J618(NH) 3 (IEC-61162-1)
SCALE
DRAWN
NC
DWG.No.
CHECKED
1 GND
APPROVED
2 OP_HD_2
3 GND J601
SHIP'S ALARM SYSTEM
Feb. 2, '05
4 NC 1 RS-232C CABLE
船内アラームシステム
OP_BP_2
5 GND RXD 2 PC
6 OP_TRIG_2 TXD 3
*2
7 GND NC 4
RW-4864,φ9.5 GND 5
MASS
SUB DISPLAY2 8 OP_VIDEO_2
NC 6
100-240VAC
(SEMI-LOG) NC 7
C3527-C01- G
Y. Hatai
J204 DVI-D MONITOR NC 8
1 DVI0TX2_N NC 9
TAKAHASHI.T
2 DVI0TX2_P
kg
E. .MIYOSHI
3 A_GND
4 NC J611(TB)
5
5 NC AIS_TD_A 1
*1 *5
BREAKER
6 NC AIS_TD_B 2 P
100-230VAC
7 NC AIS_RD_A 3 *1
8 NC AIS_RD_B 4 P
TTYCS-4
*1
*1
12 J620(TB)
制御部
NC
3.5m, φ8.6
RPU-013
2
1
13 NC TRK_TD_A 1
IV-1.25sq.
*1
14 VCC TRK_TD_B 2
保護アース PE
*1
NR203PF-VVS1.25,
TB1
15 GND TRK_RD_A 3
03-163-6003-0
P TTYCS-1
16 NC TRK_RD_B 4 TRACK_CONTROL
3
2
1
17 DVI0TXD_N GND 5
PROCESSOR UNIT
(IEC-61162-1)
18 DVI0TXD_P
AC
AC
GND
19 A_GND
20 J612(TB) *1
NC
21 TTYCS-7
NC ALARM1_0 1
P
NAME
TYPE
MU-231CR
(8PORTS)
MONITOR UNIT
6 NC SYS_FAIL_H 11 7
6
TMDS_DATA(-) 9 P チャ BRN
相互結線図
7 NC SYS_FAIL_C 12 8 NC
TMDS_DATA(+) 10
IV-8sq. *1
8 NC
TMDS_DATA1/3_SHIELD 11 9 DVI0TX1_N
保護アース PE
NC 12 10 DVI0TX1_P
NC 13 11 A_GND
+5V_POWER 14 NETWORK MPS588-C J302
12 NC
MARINE RADAR/ARPA
HOT_PLUG_DETECT 16
船舶用レーダー/ARPA
TMDS_DATA0/5_SHIELD 19
INTERCONNECTION DIAGRAM
17 DVI0TXD_N NC 5 5 NC
NC 20 RXN
*6
18 DVI0TXD_P RXN 6 6
NC 21
*2
19 A_GND NC 7 7 NC
TMDS_CLOCK_SHIELD 22 20 NC NC 8 8 NC
TMDS_CLOCK(+) 23 21 NC
TMDS_CLOCK(-) 24 22 A_GND J614(TB) MJ-A3SPFD J1
*3 シロ WHT MJ-A3SPF0015-100,10m,φ6
23 DVI0TXC_P +12V 1 クロ BLK
1 +12V
DVI CABLE GND 2 2 GND
EXT. MONITOR 24 DVI0TXC_N
3 FG
S - 14
IV-1.25sq.
D
C
B
A
*7 DPYCY-1.5 *1
氷結防止用 100VAC,1φ,50-60Hz
TB901
*5
*4
*3
*2
*1
DE-ICER DPYC-1.5 *1
:
:
:
:
:
110/115/220/230VAC, 1 100VAC_H
NOTE
RU-3305 *2
1φ,50-60Hz 2 100VAC_C
RSB-105
RSB-104
3 NC
空中線部
OPTION
200VAC,3φ,50Hz J911
1
(380/440VAC)
(200/220VAC)
ANTENNA UNIT
USER SUPPLY
モニター
+12V
MONITOR
FOR MOTOR IN ANTENNA UNIT 380VAC,3φ,50Hz TPYC(Y)-2.5 *1 3
WITH DE-ICER
氷結防止あり
PM-51
-12V
保護アース PE
*1
IV-3.5sq.
440VAC,3φ,60Hz
1
SHIPYARD SUPPLY
PERFORMANCE
GND
パフォーマンス
TPYC(Y)-2.5 *1 5 PM TRIG
110VAC,3φ,60Hz RU-5693 *2
( SHIPYARD SUPPLY )
6 PM ENABLE
TPYC(Y)-2.5 *1
220VAC,3φ,50Hz RU-6522 *2
TB 03P9349
TPYC(Y)-2.5 *1
NC
NC
GND
GND
PM-ENABL
PM-LEVEL
PM-TRIG
-12V
BP
HD
+12V
RW-4747
NO DE-ICER
TB803
440VAC,3φ,50Hz RU-5466-1 *2
氷結防止なし
3φ(W) 3
3φ(V) 2
3φ(U) 1
9
8
7
6
5
4
3
2
1
11
10
TB902
*1 *5
BREAKER
*1 TB1 03-2088(6-14P)
2
1
14
13
100-120/200-240VAC DPYC-2.5
J1
1 H
1φ, 50-60Hz
2 C
GYRO
03-2090(3P)
J5(VH)
64P1106A
20/30m
MAX,30m
3
2
1
BRN
MPYCY-12
トランス
1
TPYCY-2.5
*1 GYRO_R2
DPYC-1.5 RED 2
*1
10-12:NOT USED
GYRO_R1
CONVERTER
BOARD *2
TB911
J680 3 NC
3φ(W)
3φ(V)
3φ(U)
1
*2
TRANSFORMER
NC
GYRO_CLK-C
GYRO_CLK-H
GYRO_DATA-C
GYRO_DATA-H
アカ
03P9342
J4(VH)
2
J7(NH)
ダイ ORG 1
TB BOARD
3 GYRO_S1
5
4
3
2
1
TB912
TB803
9 GND
8 GND
4 キ YEL 2 GYRO_S2
4 -12V
1 +12V
*1 5 J613(TB) *4
5 PM-TRIG
キ
アオ 4
7 PM-ENABL
6 PM-LEVEL
03-2091(5P)
チャ BRN
ダイ ORG
チャ BRN
YEL
アカ RED
1 TX_HV
2 NC
*5
*3
*4
*2
*1
J610(TB) ダイ(太) ORG[B]
J608(TB) 24V_PLUS 1 3 24V_PLUS
2
:
:
:
:
:
注記
1 AD_DATA_H J603(XH) 24V_MINUS 2 キ(太) YEL[B] 4 24V_MINUS
P アオ(太) BLU[B]
*1 2 AD_DATA_C 3 5
3 AD_CLK_H ハイ(太) GRY[B]
J615(TB)
TTYCS-4 4 6
-12V 5
GND 4
+5V 3
GND 2
+12v 1
P ムラサキ(太) PPL[B]
A-D CONVERTER 4 AD_CLK_C 5 7
6 シロ(太) WHT[B] 8
RTR-082
造船所手配
オプション
キ アカ ミドリ GRN
SPU_RF_D_B 8 10 SPU_RF_D_B
BRN
ユーザー手配
ダイ クロ BLK
RED
RF_SPU_D_A 9 11 RF_SPU_D_A
GRN
YEL
ORG
RF_SPU_D_B 10 シロ WHT 12 RF_SPU_D_B
6
5
4
3
2
1
ミドリ(太) GRN[B]
3
2
1
SG 11 13 SG
アカ(太) RED[B]
J3
J4
GND 12 14 GND
TRANSCEIVER UNIT
NC
NC
GND
VCC
GND
GND
+12V
+12V
TB-802
コンバータ
J609
-5/-12V
RGBビデオ
J3 IF_VIDEO IF_VIDEO
ストレートケーブルを使用
DVI-RGB-1
CONVERTOR
RGB VIDEO
DVI1TX2_N 1
DVI1TX2_P 2
IV-8sq. *1
A_GND 3
保護アース PE
*2
NC 4 TOTAL : UP TO 31.5m
*7 : 船内配電盤では3Aのブレーカを使用
NC 5 合計 : 31.5m以下
03P9229A
NC 6 XH10P-W-6P XH10P-W-5P-A
J9 1.5/10/20/ 1.5/10/20/
RGB-BUFF基板
NC 7 J602(XH) J501/J521 J501
DVI-RGB変換基板
最長 100m ( 100mを超える場合はRJB-001が必要 )
保護アース PE
交流は両極切りブレーカ(造船所手配)を経由すること
*1 6 GND GND 4 8 GND GND 15 GND 8 8 GND GND 8 8 GND
*6 : CU-200/RPU-013間はクロスケーブル、CU-200/HUB-100間は
COAXIAL 7 GND B_VIDEO 5 9 B NC 16 SYS_FAIL_H 9 9 SYS_FAIL_H NC 9 9 NC
CABLE(75Ω) x 5 8 GND GND 6 10 GND DVI1TXD_N 17 SYS_FAIL_C 10 10 SYS_FAIL_C NC 10 10 NC
VDR 9 NC 7 18
H_SYNC DVI1TXD_P
DSUB-BNC-1
10 GND GND 8 A_GND 19
CONVERTOR *2
11 GND V_SYNC 9 NC 20
SLB-FRN4-A
または
BNCコネクタコンバータ
BNC CONNECTOR
12 NC 10 21 J507/J527
GND NC
操作部
操作部
1 SYS_FAIL_H
RCU-015
RCU-014
RCU-016
2 SYS_FAIL_C
*2
SYS_ACK_C
J616(NH)
J621(TB)
1 GND J605(TB)
2 OP_HD_IN HDG_A 1
3 GND P *1
HDG_B 2 TTYCS-1Q
4 OP_BP_IN HDG_GND 3 HDG SENSOR
5 GND
*2 6 OP_TRIG_IN
(IEC-61162-2)
7 GND J607(TB)
RW-4864,φ9.5 *1
MASTER RADAR 8 OP_VIDEO_IN LOG_A 1
LOG_B P TTYCS-1
2 SPEED LOG
NC 3 (IEC-61162-1)
J617(NH)
4
1 GND
2 OP_HD_1 J606(TB)
*1
3 GND NAV_A 1
P TTYCS-1
4 OP_BP_1 NAV_B 2 NAVIGATOR
5 GND NC 3 (IEC-61162-1)
6 OP_TRIG_1
*2 7 GND
RW-4864,φ9.5 J619(TB)
SUB DISPLAY1 8 OP_VIDEO_1 *1
ARPA_A 1 TTYCS-1
(FULL-LOG) 2 P
ARPA_B ECDIS
3
SCALE
DRAWN
J618(NH) NC (IEC-61162-1)
DWG.No.
CHECKED
1 GND
APPROVED
2 OP_HD_2
3 GND J601
SHIP'S ALARM SYSTEM
Feb. 2, '05
NC 1
船内アラームシステム
MASS
8 OP_VIDEO_2 GND 5
SUB DISPLAY2 NC 6
100-240VAC
(SEMI-LOG) NC 7
Y. Hatai
C3528-C01- G
J204 DVI-D MONITOR NC 8
NC 9
TAKAHASHI.T
1 DVI0TX2_N
2 DVI0TX2_P
kg
E. MIYOSHI
3 A_GND
4 NC J611(TB)
5
5 NC AIS_TD_A 1
*1 *5
BREAKER
6 NC AIS_TD_B 2 P
100-230VAC
7 NC AIS_RD_A 3 *1
P
*1
8 NC AIS_RD_B 4 TTYCS-4
*1
J620(TB)
制御部
12 NC
RPU-013
2
1
13 NC TRK_TD_A 1
IV-1.25sq.
*1
14
保護アース PE
NR203PF-VVS1.25,
VCC TRK_TD_B 2 *1
TB1
15 GND TRK_RD_A 3
03-163-6004-0
P TTYCS-1
16 NC TRK_RD_B 4
3
2
1
TRACK_CONTROL
17 DVI0TXD_N GND 5
PROCESSOR UNIT
(IEC-61162-1)
18 DVI0TXD_P
AC
AC
GND
19 A_GND
20 NC J612(TB) *1
21 NC TTYCS-7
ALARM1_0 1
P
NAME
TYPE
SINGLELINK5M/10M,φ7 ALARM2_0 3
MU-231CR
(8PORTS)
P
MONITOR UNIT
3 A_GND 4
DDC_CLOCK 6 EXT_ALM_ACK_N 9 シロ/アオ WHT/BLU P NC
4 NC 5
DDC_DATA 7 GND 10 P ダイ ORG RXN
5 NC 6
NC 8 6 シロ/チャ WHT/BRN 7 NC
6
NC SYS_FAIL_H 11
P チャ BRN
相互結線図
FAR-2837SW
TMDS_DATA(-) 9 7 NC 8 NC
SYS_FAIL_C 12
TMDS_DATA(+) 10
IV-8sq. *1
8 NC
TMDS_DATA1/3_SHIELD 11
保護アース PE
9 DVI0TX1_N
NC 12 10 DVI0TX1_P
NC 13 11 A_GND
+5V_POWER 14 NETWORK MPS588-C J302
12 NC
MARINE RADAR/ARPA
船舶用レーダー/ARPA
TMDS_DATA0/5_SHIELD 19
INTERCONNECTION DIAGRAM
17 DVI0TXD_N NC 5 5 NC
NC 20
*6
NC 19 A_GND NC 7 7 NC
TMDS_CLOCK_SHIELD 22 20 NC NC 8 8 NC
TMDS_CLOCK(+) 23 21 NC
TMDS_CLOCK(-) 24 22 A_GND J614(TB) MJ-A3SPFD J1
*3 シロ WHT MJ-A3SPF0015-100,10m,φ6
23 DVI0TXC_P +12V 1 クロ BLK 1 +12V
DVI CABLE GND 2 2 GND
EXT. MONITOR 24 DVI0TXC_N
S - 15
3 FG
IV-1.25sq.
1 2 3
S - 16
制御部
PROCESSOR UNIT
RPU-013 IEC-61162-2
J605(TB)
HDG_A 1 *1
J3 HDG_B 2 TTYCS-1T
RGB バッファ 基板 HDG_GND 3 HDG SENSOR
RGB BUFFER PCB DVI1TX2_N 1
03P9229A DVI1TX2_P 2 (IEC-61162-2)
3
A DVI-RGB
A_GND
NC 4
J607(TB)
LOG_A 1
*1
TTYCS-1
NC 5
変換基板 6
LOG_B 2 LOG
NC NC 3
DVI-RGB NC 7 (IEC-61162-2)
CONVERSION NC 8
*5 J2 9
VGA CABLE BOARD DVI1TX1_N J606(TB)
RGB EXT. MONITOR 1 R_VIDEO DVI1TX1_P 10 *1
NAV_A 1 TTYCS-1
2 G_VIDEO A_GND 11 NAV_B
12
2 NAVIGATOR
3 B_VIDEO SLB-FRN4-A NC NC 3
4 NC NC 13 (IEC-61162-2)
5 NC VCC 14
6 GND GND 15 J619(TB)
*1 COAXIAL BNC CONNECTOR 7 GND NC 16 *1
CABLE(75Ω) x 5 ARPA_A 1 TTYCS-1
CONVERTOR 8 GND DVI1TXD_N 17 ARPA_B
VDR 9 18 2 ECDIS
BNCコネクタコンバータ *5 NC DVI1TXD_P NC 3
*5 10 GND A_GND 19 (IEC-61162-2)
DSUB-BNC-1 11 GND NC 20
12 NC NC 21
13 H_SYNC A_GND 22
14 23 RS-232C
Y_SYNC DVI1TXC_P
15 NC DVI1TXC_N 24 J601
NC 1
RXD 2
TXD 3
NC 4
GND 5
NC 6
J616(NH) NC 7
B 1 GND NC 8
9
2 OP_HD_IN NC PC
3 GND
4 OP_BP_IN
5 GND IEC-61162-2
6 OP_TRIG_IN J611(TB)
7 GND AIS_TD_A 1
RW-4864,φ9.5
MASTER RADAR 8 OP_VIDEO_IN AIS_TD_B 2
AIS_RD_A 3 *1
AIS_RD_B 4 TTYCS-4
J617(NH) AIS_GND 5 AIS
1 GND (IEC-61162-2)
船内アラームシステム
2 OP_HD_1
3 GND
SHIP'S ALARM SYSTEM
4 OP_BP_1 J620(TB)
5 GND RSV3_TD_A 1
6 OP_TRIG_1 RSV3_TD_B 2 *1
SUB DISPLAY1 RW-4864,φ9.5 7 GND TRK_RD_A 3 TTYCS-1
8 OP_VIDEO_1 TRK_RD_B 4 TRACK_CONTROL
(FULL-LOG)
GND 5
J618(NH)
1 GND 電源
J612(TB) *1 POWER SUPPLY
2 OP_HD_2 TTYCS-7
3 GND ALARM1_0 1
4 OP_BP_2 ALARM1_1 2
5 GND ALARM2_0 3
6 OP_TRIG_2 ALARM2_1 4
C SUB DISPLAY2 RW-4864,φ9.5 7 GND ALARM3_0 5
(SEMI-LOG) 8 OP_VIDEO_2 ALARM3_1 6
ALARM4_0 7
ALARM4_1 8
ALM_ACK_IN_0 9
DVI-D MONITOR ALM_ACK_IN_1 10 ネットワーク ハブ
FR-FTPC-CY, NETWORK HUB
*5 J205 SYS_FAIL_N 11
DVI-D/D SINGLELINK5M SYS_FAIL_C 12 10/20/30m, φ13 MPS588-C
EXT. MONITOR 1 DVI0TX2_N *5
シロ/ミドリ WHT/GRN
2 DVI0TX2_P ミドリ GRN 1 TXP
P
3 A_GND 2 TXN
シロ/ダイ WHT/ORG
4 NC 3 RXP
アオ BLU
5 NC 4 NC
シロ/アオ WHT/BLU P
6 NC 5 NC
ダイ ORG
注記 7 NC シロ/チャ WHT/BRN
6 RXN
8 NC 7 NC
*1)造船所手配 9 DVI0TX1_N
チャ BRN
8 NC
10 DVI0TX1_P
*2)コネクタは工場にて取付済み。 11 A_GND カード I/F ユニット
12 NC
*3)オプション。 13 NC
P5E-4PTX-BL CARD I/F UNIT
NETWORK *10m*,φ6.3 CU-200
*4)コネクタクランプでアースに落とす。 14
15
VCC MPS588-C J302 *3
GND
TXP 1 1 TXP
*5)ユーザー手配 16 NC
TXN 2 2 TXN
17 DVI0TXD_N
18 RXP 3 3 RXP
DVI0TXD_P
19 NC 4 4 NC
A_GND
NC 5 5 NC
D NOTE
20
21
NC
NC RXN 6 6 RXN
NC
22 A_GND NC 7 7
*1: SHIPYARD SUPPLY. 23 DVI0TXC_P NC 8 8 NC
24 DVI0TXC_N
*2: CONNECTOR PLAG FITTED AT FACTORY. J614(TB) MJ-A3SPF0015-100,10m,φ6 MJ-A3SPFD J1
+12V 1 1 +12V
*3: OPTION. GND 2 2 GND
3 FG
*4: GROUNDING THRU CONNECTOR CLAMP
*5: USER SUPPLY
DRAWN TITLE
Mar. 30 '04 K.MIYAZAWA RPU-013
CHECKED 名称
TAKAHASHI.T 制御部外部信号接続
APPROVED
Y. Hatai 相互結線図
SCALE MASS NAME
kg PROCESSOR UNIT EXTERNAL INTERFACE
DWG.No.
C3528-C02- A 03-163-6004-0 INTERCONNECTION DIAGRAM
1 2 3 4
C
DRAWN TITLE
注記 Sep. 17 '04 T.YAMASAKI FAR-2127/2827
CHECKED 名 称
*1)造船所手配。 Sep. 17 '04 T.TAKENO 空中線ケーブル延長
APPROVED
NOTE Sep. 25 '04 相互結線図
NAME
*1. SHIPYARD SUPPLY. ANTENNA CABLE EXTENTION
DWG.No.
S - 17