Professional Documents
Culture Documents
1. After the examination and confirmation in Part III, carry out the following steps:
(3) Confirm no people within the well and car, being suitable to the conditions for elevator’s safety
operation;
(4) Confirm that the construction outside the well has no influence on elevator’s safety operation;
2. Examine the main power voltage according to 3-phase and 5-wire at the site:
Measure the main power voltage at the leading end of 1QF1 power control box, keeping
230±7%VAC and deviation not over 15VAC. Via main transformer’s voltage regulating so that the
3. Examine the specification of main wire and capacity of main circuit breaker in accordance with
4. After the confirmation of regular operation on above examination items, carry out power on
adjustment.
(1) Close the main power circuit breaker 1QF1, then examine the voltage between L1, L2 and L3.
(2) examine the power supply of 1TC1 and 1TC2 transformer in control cabinet and measure the
voltage as below:
Output(wire making:118、119):110±7%VAC
Lighting transformer 1TC1:
Input: 220±7%VAC
(3) As under normal operation, then close corresponding control switch 1QF6 1QF8 of control
cabinet, examine the output voltage of transformer and regulated power supply, measure the voltage
as below:
class)
Output(Wire makeing:5V、0V1):5VDC;
1、 At the same time , the state of insulation between 0V1 and 0V can be
(1)、Display
If the output of the regulated power supply G1、G2 is correct。Close the power switch 1QF7 of
Push the key Enter,it will enter the main interface of main controller :
The following is the corresponding explanation of the bottom left corner state:
Automatic(AUTO)
Test(TEST)
Fire control(FIRE)
Driver (MANUAL)
Fulload(FULLY)
Overload(OVER)
Open door(OPEN)
Close door(CLOSE)
Self-learning(LEARN)
Leveling (LEVELL)
The following is the corresponding explanation of the bottom right corner state:
Open door (open)
Close door (close)
(2)、Menu
In the main interface , push the Enter key, it will enter the selection of mode of main
menu,for example:
In the menu:the first digit figure indicates the main menu,the second digit figure indicates
selection of main menu and return to main interface,Enter key will enter the selection of submenu
item.
menu. After the option is confirm, pushEnterkeyto enterthe submenu of this menu. The operation
after entering submenu is the same as that at main menu. In the edit pattern,push“↑”、“↓”key
to alterparameter value. After the parameter value is confirmed, push Enter key to save parameter
value. Esckey to quit modification. The defaulting have been set initially for all the parameters in
controller before ex works. But some parameters must be set anew as per the on site situation.
Main menu:
Configuration (CONFIG)
Time setting(TIME)
Setting of station(landing)(STATION)
Call menu(CALL)
Door (DOOR)
password(PASSWORD)
The following is the description of the function and setting of some menus.
A、 Configuration of menu(CONFIG)
ADDRESS:The scope for selection is 0-15. it is mainly used for setting the address of elevators
during the paralleling 、group control or remote monitoring of elevators(when two elevators are in
CONNECT : OFF-LINE is the normal work module of elevator ; ON-LINE is the automatic
calling work module.
SPEED : Select the speed output of main controller , select V<1.5m/S , microprocessor only
output one speed signal V1; if V>1.6m/s,microprocessor will output two speed signals V1、V2;
if V>2.0m/s,microprocessor will output three speed signals V1、V2、V3.(The speed value that
FLOOR DISPLAY:Set the display mode of each floor,push key ENTER to enter the following
interface:
When the display mode is modified, only need to push key ENTER,the modifying cursor “>”
sign will arise,then use “↑”、“↓”key to modify the value. After the modification is finished,
push Ente key to save the modified result. If the Esc key is pushed, it will exit from the
modification state.
MANUAL DOOR:Set clsoig door state under the driver state. OFF mode:need to push button
MANUAL DIRECTION:Set if driver state external call can stop the elevator or not。OFF mode:
external can’t stop the elevator; ON mode:external call can stop the elevator.
2) set the time of lighting , by this setting when there is no one to call the lift the light in car is
BRAKE: unused.
DOOR OPEN:set the time of opening door , the acquiescent value is 2.1s.
DOOR CLOSE:Set the time of automatic closing door. the acquiescent value is 5s.
OPEN PROTECT:Set time of opening door protection.when opening door limit cannotbreak off
because of fault,this protection time value can be set ,door machine will stop opening door so
the danger of door machine being damaged for long time’s Power ON can be prevented, the
CLOSE PROTECT:Set the time of closing door protection. When door lock or closing door limit
can’t be connected or break off because of fault,set this protection time value so that door machine
stops closing door,and opening door anew, the acquiescent value is 8s.
RINGING : Under the driver state , set the sounding time of buzzer when there is external call
value is 1s.
TIME1 : the safety touching plate is acting, the ring time of buzzer , the
TIME3:1)backup
2) set the time of button locking , the setting value of parameter is more than 180s. (this
function is fit in with Singapore)
BASE:Set the main stop and locking elevator landing of paralleled elevator. The floor value of this
FIRE HOUSE : Set it return to that landing , this value is set according to absolute floor when
WAIT(1): When the group control or paralleling of elevator is set, at ordinary times it waits on
that floor.
WAIT(2): When the group control or paralleling of elevator is set, at ordinary times it waits on
that floor.
D、Call menu(CALL)
This menu can be used for directly observing or registering the call signals of each floor,and being
able to monitor and modify the signals registered by external call of elevator. After call signal is
registered,this call signal will be erased after elevator run to this landing.
Submenu:( UP CALL)
(DOWN CALL)
(CAR CALL)
This menu can monitor main controller I/O state, which can’t be modified.
DOOR 1:Set the floors where 1# door can be opened. “1”:can open the door,“ 0”:can’t
G、(ERROR HISTORY)
When error arises,the error code and failure reason will be scrolled and displayed on the lower of
MPK708n main controller can record 50 history errors. Through this menu, the time when the error
H、PASSWORD
it can carry out concerned commissioning work under concerned password level.
After entering operation state,power is on anew or there is no any key press after 15 minutes ,it
L、(PULSE MONITOR)
RUN_IN : record 1/4the length of magnetism-insulating board. ( see the back for the
commissioning method)。
After key Enter is pushed, enter the the mode of examing pulse number:
When key“↑” or “↓”is pushed, the pulse number of each landing can be examined. In order to alter
pulse number, push key Enter to enter(see the back for the commissioning method):
Means double door operators and double control boxes or single door operator, need
1 two door operators action at the same time, if only one door operator ,the second
2 Means double door operators and double control boxes , the operators be controlled
respectively
REPAIR OPEN :
ARRIVE LAMP : OFF no arrive lamp function .ON ,have arrive lamp.
ERROR OPEN TIMES : Times of erroe open , the function is cancelled when the value is 0.the
setting value is above 0,the auto close door will be stopped when the failing times of close door is
above the setted value .push the close button ,the door will try to close again.
FORCE CLOSE :OFF, no force close function. ON, have force close function.
When car top inspection is on the ‘inspection’ , the safty circuit commissioning is
indicator light of phase sequence relay will shine. (if there is phase relay)
don’t act.
When the above conditions are met,safety circuit relay 5KA1 will act.
At the same time,in the main controller menu option(IO), open the input (I)dot-monitor
If normal display is not correct or there is error display ,the following commissioning can only be
Inverter keyboard is composed of LCD monitor、7 indicator lights and function keys.
The state of the inverter’s driving signalcan be discern,its contens are as follows:
Note : For the concrete operation instruction of inverter, see the 《 SIEI inverter operation
instruction》
R: 0 S: 0
MONITOR
Or after push key SHIFT, push key HOME , the above page layout will arise 。 The above page
The transducer and the corresponding traction machine have been adjusted before leaved factory , so
the adjuster only need use the following menus to adjust the elevator.
A、Monitor
Monitor:
Name Content Unit /note
E:enable
1、2:direction
DI 7654321E Input state
4、5、6:speed
0:operation contactor
1:braking contactor
DO 3210 Output state
2:Inverter failure
Alarm log:This function provides 30 inverter errors or sytem error information,display time and
B、Travel(operation menu)
Startup config:
—Enter setup mode—Drive data(drive parameter)
According to motor parameter,
—Motor data(motor parameter) drive is set at this time.
—Autotune (slef-adjustment) used during the autotune of motor.
—Load setup:After the motor、drive parameter are altered,load system will inquire
if choose Load,choose Yes/No.
—Mechanical data:traction parameter is set at this time.
—Weights:The parameters of car、counterweight and so on are set at this time.
—Encoders config : The configuration and setting of encoder.(standard parameter
setting )
—Motor protection:Motor protection setting (standard parameter setting )
—BU protection:BU protection. (standard parameter setting )
—Load default:All the parameters of inverter are restored to the ex works defaulting.
C Travel(operation menu)
—Max linear speed : This parameter is read-only parameter, shows the maximum
linear speed(mm/s).
Ramp profile—MR0 : This parameter is set for operating slope. This manual use the defaulted
parameter group MRO. See the posterior chapters for the concrete commissioning method.
Lift sequence:
See The setting of elevator run standard
Speed threshold: parameter
Ramp function:
Save parameters:
E I/O config:Inverter I/O dot configurating. (See The setting of elevator run standard parameter
)