Professional Documents
Culture Documents
Blum Tandem 563F Installation Instructions
Blum Tandem 563F Installation Instructions
1 Rotate side-to-side adjustment left or 2 After front side-to-side adjustment is 1 Press up on adjustment tab Rotate the tilt adjustment lever on the rear of
each runner to lift the back of the drawer and
right equally on both locking devices. Drawer made with the locking devices, rotate the 2 Push towards back of drawer tilt the top of the drawer front forward
front moves in the same direction as rotation. rear side-to-side adjustment left or right
to re-align the back of the drawer box with
the front. Drawer back moves in the same
direction as rotation.
0
R
2
Drawer front L
1
R
Maximum 3 (1/8") rise of drawer front (tool-free) Maximum 5 (3/16") rise of drawer back (tool-free)
L
NOTE: Height and tilt adjustments available with all combinations of locking devices and runners
R
L
Turning the adjustment screw allows
for up to a + 2 .5 (3/32") out adjustment
Maximum 1.5 (1/16") to left or right in both front and rear (tool-free) NOTE: For T51.1901.PS setback in inset
NOTE: Side-to-side adjustment not available on T51.x8xx locking devices applications, see page 5
Subject to technical modifications without notice. © 2016 Blum Inc. 1 Dimensions in millimeters (inch equivalents as noted)
TANDEM plus BLUMOTION Drawer Specifications
11 (7/16")
Screws
606N or 606P 24.5 (31/32") 13 (1/2")
Opening height
or 35 (1-3/8") Minimum rear notch
662.1150.HG Drawer side thickness Maximum
maximum 19 (3/4") drawer height =
opening minus
20 (25/32") Preparing for hardware installation
Locking device
(1-15/32")
Installation screw
606N or 606P
Pre-boring holes for
locking devices
13 (1/2") 14 (9/16")
Bottom recess Bottom clearance
2.5 mm bit with
NOTE: Drawer side material thickness may vary. Accurate measurement of drawer side extension chuck
material thickness should be used when calculating outside drawer width using the table Pre-boring holes
below. Inside drawer width must equal opening width minus 49 (1-15/16") for TANDEM for rear hooks
Subject to technical modifications without notice. © 2016 Blum Inc. 2 Dimensions in millimeters (inch equivalents as noted)
TANDEM plus BLUMOTION Face Frame Application
37 (1-15/32")
Subject to technical modifications without notice. © 2016 Blum Inc. 3 Dimensions in millimeters (inch equivalents as noted)
TANDEM plus BLUMOTION Frameless Application
Drawer length
192 (7-9/16") 224 (8-13/16") Maximum drawer height =
Opening minus
533 (21")
Cabinet 563F4570B 20 (25/32")
457 (18") Drawer
Bottom clearance 14 (9/16")
480 (18-29/32") Minimum Front gap 1.5 (1/16")
Drawer thickness
192 (7-9/16") 128 (5-1/32")
457 (18")
Cabinet 563F3810B
381 (15") Drawer Bottom recess 13 (1/2")
Detail of front holes TANDEM plus Cabinet Minimum inside Drawer Maximum
96 (3-25/32") 128 (5-1/32") Runner
drawer
BLUMOTION depth cabinet depth length thickness length
381 (15")
Cabinet 563F3050B 563F5330B 610 (24") 557 (21-15/16") 533 (21") 548 (21-9/16")
305 (12") Drawer
32 (1-1/4")
328 (12-29/32") Minimum 563F4570B 533 (21") 480 (18-29/32") 457 (18") 471 (18-17/32")
34 (1-11/32")
563F3810B 457 (18") 404 (15-29/32") 381 (15") 19 (3/4") 395 (15-9/16")
9 (11/32") Typical
96 (3-25/32") 96 (3-25/32") 563F3050B 381 (15") 328 (12-29/32") 305 (12") 319 (12-9/16")
7 (9/32")
305 (12") 563F2290B10 305 (12") 266 (10-15/32") 229 (9") 259 (10-3/16")
Cabinet 563F2290B10
229 (9") Drawer
37 (1-15/32") 266 (10-15/32") Minimum
T51.1901R Locking device with side-to-side adjustment (right)
Subject to technical modifications without notice. © 2016 Blum Inc. 4 Dimensions in millimeters (inch equivalents as noted)
TANDEM plus BLUMOTION Inset Application
Face frame application – complete blockout Face frame application – partial blockout Frameless application
Side view Side view Side view
Runner setback (see table) Runner setback (see table) Runner setback (see table)
Trial recommended Trial recommended Trial recommended
Inside cabinet depth Inside cabinet depth range Inside cabinet depth
Minimum = Runner length + Setback + 6 (1/4") Minimum = Runner Length + Setback + 6 (1/4") Minimum = Runner length + Setback + 6 (1/4")
Setback information Runner setback when using depth adjustable locking device (T51.1901.PS)
Side view 563/569 F/A Runner setback ▬▬ Setbacks in this table recess the
13 (1/2") 17 (21/32") 20 (25/32") 23 (29/32") face of the drawer front inside of
thickness
Sub-front
Drawer front the cabinet 1 (1/32")
Runner setback 16 (5/8") 20 (25/32") 23 (29/32") 26 (1-1/32") ▬▬ The depth adjustment can then
19 (3/4") 23 (29/32") 26 (1-1/32") 29 (1-5/32") be used to move the drawer
Drawer sub-front
NOTE: Runner cannot be
Subject to technical modifications without notice. © 2016 Blum Inc. 5 Dimensions in millimeters (inch equivalents as noted)
TANDEM plus BLUMOTION Attachment Specifications
Rear attachment options for face frame applications Depth adjustment specifications
Front view Side view TANDEM plus
A B
B BLUMOTION
295.3750.02 Rear mounting bracket, 295.3700.2x For 563F2290B10, non-handed 563F5330B 244.5 (9-5/8") 500.5 (19-23/32")
A
non-handed
563F4570B 244.5 (9-5/8") 436.5 (17-3/16")
21 563F3810B 148.5 (5-27/32") 340.5 (13-13/32")
(13/16") 39.5 (1-9/16")
20.5 (13/16") 563F3050B 148.5 (5-27/32") 244.5 (9-5/8")
(11/16") (1-1/4")
32
32
Mount each runner using at least two of the elongated holes. Install the drawer to check the
17.5
12 16 (5/8") Remove the drawer, loosen screws and make adjustments if necessary, ±4.5 (3/16").
14 (9/16") 5 (3/16")
(3/32")
(15/32") Tighten the screws, verify the drawer front position and finish mounting the runners using the
4 (5/32")
2
Y
Face frame stile
Face frame stile
40 (1-9/16")
(1-1/4")
2 (3/32")
32
3 (1/8")
(3/4")
19
3.2 (1/8")
563F5330B 533 (21") 557 (21-15/16") 448 (17-5/8") 15.5 (5/8") 22.5 (7/8")
Face frame rail Face frame rail
563F4570B 457 (18") 480 (18-29/32") 378 (14-7/8") 15.5 (5/8") 22.5 (7/8")
NOTE: Use at least three 606N or 606P installation screws for 295.3750.02 or 295.3700.2x 563F3810B 381 (15") 404 (15-29/32") 319 (12-9/16") 15.5 (5/8") 22.5 (7/8")
INST-TDM563F 05.16
Subject to technical modifications without notice. © 2016 Blum Inc. 6 Dimensions in millimeters (inch equivalents as noted)