Professional Documents
Culture Documents
T S GUIDE Shelby Troubleshooting Guide v1.0
T S GUIDE Shelby Troubleshooting Guide v1.0
Troubleshooting Guides
Shelby EE Team
Date Feb. 20 2017
Now taking an example of Middle Band LTE band1(WCDMA band1)and High Band7 to introduce RF Path:
FAIL
TX VOLTAGE
CHECK & REPLACE
CHECK?
C7102,C7103,R7102,R7101,C7100,C7101
OK
FAIL
PA MODE & MATCH
CHECK? CHECK & REPLACE
C7112,C7113
OK
FAIL
COUPLE R & RF CHECK & REPLACE
CONNECTOR CHECK ? U7020,L7020,C200,L200,J201
OK
FAIL
TX LEVEL 2 Go to TX CHECK CHART- Low TX
CHECK ?
OK
OK
SDR660 FAIL
CHECK & REPLACE
TX Level C7102,C7103,R7102,R7101,C710
CHECK ? 0,C7101
OK
COUPLER
& RF FAIL
CHECK & REPLACE
CONNECT
U7020,L7020,C200,L200,J201
OR
CHECK
OK
END
Switch
FAIL CHECK & REPLACE
COUPLER,
U7020,L7020,C200,L200,J201
RF
OK CON.
CHECK ?
OK
END
OK
END
OK
OK
OK
END
OK
SDR660 FAIL
CHECK & REPLACE
TX Level
C7110,L7110,C7111,U7100,C7203,C7204,C7205
CHECK ?
OK
OK
OK
OK
END
OK
CHECK & REPLACE
SDR660 FAIL R3001,R3002
Voltage CHECK
?
OK
OK
OK
END
OK
OK
OK
OK
END
OK
OK
OK
END
OK
SDR660 FAIL
CHECK & REPLACE
TX Level
C7110,L7110,C7111
CHECK ?
OK
OK
OK
OK
END
OK
CHECK & REPLACE
SDR660 FAIL R3001,R3002
Voltage CHECK
?
OK
OK
OK
END
OK
OK
OK
OK
END
Receiver Path
GSM850 WCDMA and LTE band5;GSM900 WCDMA and LTE band8;
DCS1800 WCDMA and LTE band3;PCS1900 WCDMA and LTE band2;
OK
OK
OK
OK
END
OK
OK
COUPLE R
R&& RF
RF FAIL
FAIL
COUPLE CHECK & REPLACE
CON.
CON. CHECK
CHECK ?? CHECK & REPLACE
GSM850,EGSM:L7020,U7020,C7026, FL7030,C7041,L7041,U7050
U6000,C8000,L8000,J8000,R8001,R8002,C8001
DCS,PCS:L7020,U7020,C7026, FL7030,L7007,C7006,L7005,U7000
OK
FAIL
FAIL Go
TX
TX LEVEL
LEVEL 2
2 Go to
to TX
TX CHECK
CHECK CHART-
CHART- Low
Low TX
TX
CHECK
CHECK ??
OK
END
GPS Voltage
Check
Check
VVREG_L2A_1P0_SDR_AVDD
and replace U2000(PM660)
Ok
check the
GPS eLNA
enable
Ok
GPS Check and replace
Front/Inter-stag FL080/FL7840
e filter check
Ok
External LNA
gain check Check and replace U7810
Ok
End
2015 Lenovo Confidential. All rights reserved.
GPS Front End Block
– Both WLAN and Bluetooth share the same IC and most of the
circuit, so if one of the BT/Wi-Fi fails, the other should fail as well.
If only one of them fails, it is highly likely that it is not a hardware
problem and it could just that the BT/Wi-Fi is turned on through
the UI already and the test commands can not turn it on again.
2.4GHZ WIFI
5 GHZ WIFI
• Check DC Voltages:
• https://drive.google.com/drive/u/0/folders/0B_CJcTa8m_
DpS0d4R29iaW5qT3c
2.4GHZ WIFI
5 GHZ WIFI
2.Measure the power of the linear Vibrator driver IC at C5100. It should be around 5V.
If the power is not correct, then check U2210.
3. Check the signal across L5100/L5101 close to Vibrator connector, it should be a PWM signal, higher
than 2.0V and lower than 3.6V.
Touch control IC
Note:
(1) Products shown are developed, designed,
and made by Motorola Mobility LLC;
(2) Products using legacy Lenovo design
language have significant input from and
made by Motorola Mobility LLC.