Professional Documents
Culture Documents
2. Web login
Open a browser, input 192.168.0.88 (ping 192.168.0.88 before login)
1
Account:admin password:admin
3. System Management
3.1 System Info
Check system name, software version, MAC, IP, operating time.
Change system name, system description, OLT installation location.
2
3.2 Administrator
Create Administrator account and set authority
3
3.4 System time
Change OLT system time and NTP server address. After input NTP server IP, OLT will synchronize NTP time.
4
3.7 Backup Configuration and Import
Backup the configuration and save.
Import the the configuration file and implement.
5
3.9 System Reboot
Try to reboot the device here when a failure occurs.
6
3.11Save configuration
After you configure OLT, check the Save configuration menu=》Save the configurations you have done.
If not save, when reboot device, the previous configuration will be missing.
7
3.12 Http Configuration
4.ONU Management
4.1 You can view the registered ONUs ,optical power, reboot ONU etc in this menu.
You can check the ONU online status,version,chip set,and port number
If the chip set model of the online ONU can be seen, it can access internet; if the chip model is 0000, the
ONU status is abnormal and may not be able to access internet.
8
Select the specified PON port ==== select ONU.ONU can be manipulated when you enter the page.It is able to modify
the ONU name, check online and offline time and the light power of ONU,restart ONU, disable ONU access, restore
factory settings, etc.
(note: The light power check requires the optical module of ONU must be with DDM digital diagnosis function)
9
5.Port Management
5.1 OLT PON Port
The status of OLT PON, temperature,voltage,current and optical power of module can be viewed
here.
10
5.2 OLT GE port
Check the OLT uplink GE port status.
11
6.Performance Statistic
Check the data flow statistic of PON port, uplink ports, ONU link. This is to check if there are online users under the
ONU.If the statistic is changing, it means there is online user. You can also check uplink GE port status by the same
way.
七:VLAN Configure
Follow the below steps to set VLAN:
Transparent mode (no matter the data from the Ethernet port with or without VLAN tag, it can pass)
Tag mode (the data will add vlan Tag, the data with Tag will be forwarded with tag remove)
Translate mode (eg, the data with VLAN 200 will be changed to VLAN100)
12
13
Uplink Vlan Configuration:
8. Bandwidth Configuration
Configure ONU link bandwidth following below pictures.
ONU Link Bandwidth menu supports to configure uplink fixed bandwidth,maximum uplink guaranteed
bandwidth, maximum bandwidth,downlink bandwidth etc.
Default uplink maximum bandwidth is 1000000kb, means 1000M.
14
9. Port aggregation config
9.1 Isolation mode
There are two modes between OLT uplink ports and PON ports: switch mode and isolation mode.
Switch mode: 4 or 8 uplink ports and 4 or 8 PON ports can exchange data.That means all the 4PON or
8PON ports can share the uplink ports, if you just connect one uplink port, all the 4PON or 8PON
ports can get data from it.
Isolation mode: one PON port related to one uplink port; eg PON1 to GE1; PON2 to GE2; PON3 to GE3;PON4
to GE4.
Note: You need to restart the OLT after the mode is changed.
Aggregation
Aggregation configuration can be done only under switch mode and it is for the uplink ports.
Eg: When 4PON or 8PON ports are used at the same time, 1 uplink port is not enough for 4 PON or 8PON
ports data, then you can do aggregation . It is ok to combine G1 with G2, or G3 with G4, or 4 uplink
ports together to increase the uplink bandwidth. If OLT uplink ports have made aggregation configuration,
the switch connected to the uplink ports also need to do aggregation . (static aggregation.)
15
10. Mac aging time
16
11.2 Loop Detect
The loop detection to the specified port according to the requirements ensures the stable operation of
the
network.
12.SNMP configuration
Configure the community of Read, Write, Trap. That is also the password of the Read, Write, Trap.
When OLT is created on the SNMP network management, it should correspond to the code of read, write
and trap.
Trap Enable
Input the trap server IP. OLT alarm information will be sent to the server with this IP.
Trap port 162
After configuration, reboot the OLT SNMP server.
17
18