DNV-GL
ASSESSMENT REPORT
Assessment Report. No: OEEIN/855/PP190882/12205, Rev 0.
This Statement consists of 3 pages
This isto certify that the product(s)
Rack & Pinion Actuators
Manufactured by
WMS TECHNOLOGIES PRIVATE LIMITED
Plot No 39, Manjusar GIDC, Tal: Savli DIST: Vadodara - 391775
has on a voluntary basis been assessed with respect to
the requirements for Technical Documentation specified in Annex II B & Annex VII, part B (a) and (b) of
Council Directive 2006/42/EC on Machinery, as amended, and the Technical Construction File [TCF] for the
products [Rack & Pinion Actuators] as mentioned overleaf, has been assessed and found to be in compliance
with the Machinery Directive 2006/42/EC
Further details are given overleaf
Place and Date Certificate is valid until
Pune: 2017-08-30 2020.08.29 a
Gaus Ibrahim Sindgi
Sr Surveyor & Service Lead PED [Oil & Gas}
Ne: Te cere ses terms ad cnn vere ny sii changes or conrvcion may rene hs eee vali
‘Theda signed anderen dernieddacones i the orion al cee
Page of3DNV-GL
Jurisdiction: Application of Machinery Directive 2006/42/EC
Description Issue Date
o Final issue 2017-08-30
Products covered by this Statement
Rack & Pinion Actuators
THT WACT: Worldwide Actuator
[2] RO -Quarter Turn (6=90°), RP= Partial Turn((0%<0<180°), RH™ Half carn (0-180)
[3] Basic Model Torque: Eg. IfXXXX= 0215, The OP Torque i 021S= 215 Nom @ bar,
[4] Seal Material; N= NBR, V~ Viton, P= Polyethylene, F-Fluoroslcone.
[5] Materia of Construction: A= Aluminum Rack, S=SS Rack, N= ENP Coated Rack & pinion, ZAMS
[6] Actuator Type:
[a] T=Donble Acting
{b| C-Single Acting SPRING RETURN Fail Close
Ic] A=Single Acting SPRING RETURN Fail Open
[7] Spring Set No:
[a] For Double Acting = 00
[b] For Single Acting = XX.
sr Product Specifications Model Numbers
No
1 _| Rack Pinion xe Pacumatie Double Acting Actuator (Quarter Tura) (090°) WACT-RO-XXXX: a -T00
Rack & Pinion type Pacumatic Single Acting/Spring Return Actuator (Hi WACT-REEXNXX: au -T00
2 | Tarm (0=180%)
4g _| Rack Pinon pe Pacumate Double Acting Actuator (Partial Torn) WACT-RP-XXXX- aa -T00
(*<0<180°)
Rack & Pinion type Pneumatic Fall Close Single Acting/Spring Return WACT-RO-XXXX- aaa -CXX,
4 | Actuator (Quarter Turn) 6-90")
Rack & Pinion type Pneumatic Fall Close Single Acting/Spring Return WACT-RH-XXXX- oud -CXX
S| Actuator ait Fara) (0=180°)
«6 Risks Pinion ype Pacumatc Fail Close Single Acting Spring Return WACT-RP-XXXX- aa -CXX
Rack & Pinion type Pneumatic Fall Open Single Acting/Spring Return WACT-RO-XXXX- cau “AXX
7 | Actuator (Quarter Turn) (0-90°)
[Rack & Pinion type Pacumatic Fail Open Single Actng/Spring Return WACT-RE-XXXX- aaa -AXX,
8 | Actuator (Half Tura) (8-180)
‘Rack & Pinion type Pncumatic Fail Open Single Actng/Spring Return WACT-RP-XXXX- aad -AXX
9 | Actuator Partial Turn) (0% 0 <180*)
Sites Covered:
Nace he cea suc oman cons vere Ay sian changes eso contrcton may render |
‘he gall signed and eerily ated dacemen i te orginal end vali cere
age2of3WMS TECHNOLOGIES PRIVATE LIMITED DNV'GL
Plot No 39, Manjusar GIDC, Tal: Savli Dist: Vadodara - 391775, Gujarat [India]
Documents Reviewed:
TICF Reference No: WMS-ATEX-TCF 02 Rev A
‘Terms and conditions
The certificate is subject to the following terms and conditions:
In case of damages caused by defective products, directive 85/374/EEC, as amended, will apply
1, The Certificate is only valid for the product(s) listed above
2. The Certificate is concemed with the design of the product, only
3. Althe Bought-Out Components, like Solenoid Valves, Limit Switches, etc. assembled withthe product, shall be readily
procured with CE Marking, complying tothe respective Produet EU Directive
‘The following may render this Certificate invalid:
1. Changes in the design or construction of the product(s)
2. Changes or amendments to the referenced directve(s)
3. Changes or amendments in the standard{s) which form the basis for documenting compliance with the essential
requirements ofthe drective(s)
Conformity declaration and marking of product
In order to fully meet with the requirements of the Directive, the manufacturer must take all measures necessary to ensure
that the manufactured product comply with the technical documentation and with the requirements of the Directive and
finally draw up Declaration of Incorporation (Dol], of partly completed machinery.
END OF THE STATEMENT
Nee he coment co rms an cantons overle Ay sian changes in desig or comcrctin may rnd sera
The dgtly sine end eecroncaleertied dame the orina and velit cee
age 03