Professional Documents
Culture Documents
S/5 Aespire: GE Healthcare
S/5 Aespire: GE Healthcare
GE Healthcare
S/5 Aespire
Essential performance
Compact design
Features
• Enhanced monitor integration capabilities with our
Datex-Ohmeda Anesthesia Monitor and Compact
Anesthesia monitor
• Lightweight and compact for easy maneuverability
• Optional integrated auxiliary O2 flowmeter and
suction control
7100 Ventilator
• Volume and Pressure modes with electronic PEEP
• Exhaled volume, airway pressure and inspired oxygen
monitoring capabilities
S/5 Aespire® shown with Datex-Ohmeda Compact • Direct access to ventilator parameter settings
Anesthesia Monitor and Tec® 7 Vaporizers
• Smart alarms direct user to specific problems and
affected parameters
• Pressure bar graph for visual reference on a breath-by-
breath basis (optional pressure waveform available)
Physical specifications
Dimensions DIN rail
Height: 134.5 cm/52.9 in Side of machine: 34.5 cm/13.6 in
Oxygen
Modes of ventilation
percentage: 5% to 110%, 1% resolution
Volume Control mode
With tidal volume compensation (optional) Airway pressure: –9 to 99 cm H2O, 1 cm H2O resolution
Inspiratory/ Subatmospheric
expiratory ratio: 2:1 to 1:6 pressure: Paw < –10 cm H2O
(increments of 0.5)
Alarm silence
Inspiratory countdown
pause adjust: 5% to 60% of timer: 120 to 0 seconds
inspiratory time
(increments of 5%)
AN3968-E.qxd 26.10.2005 10:04 Sivu 4
Ventilator accuracy
Delivery/monitoring accuracy Ventilator screen
Volume Display size: 120 mm x 92 mm
delivery: > 200 mL = better than ±10%
Set TV Display
density: 1/4 VGA standard
75 to 200 mL = better than ±20 mL
Battery back-up
< 75 mL = better than ±15 mL
Backup power: Demonstrated battery time
Pressure under typical operating
(PInspired) delivery conditions is 90 + minutes
repeatability: ±2 cm H2O when fully charged. Battery
time under extreme conditions
PEEP delivery is 30 minutes.
repeatability: ±2 cm H2O
Battery type: Internal rechargeable sealed
Volume lead acid
monitoring: > 200 mL = better than ±10%
Communication port
75 to 200 mL = better than ±20 mL
Serial
< 75 mL = better than ±15 mL interface: Isolated RS-232C
compatible port
Pressure
monitoring: Better than ±2 cm H2O and ±5%
Anesthetic agent delivery
of reading (whichever is greater)
Delivery
Ventilator components
Vaporizers: Tec 5, Tec 6 Plus, Tec 7
Flow transducer
Number of
Type: Variable orifice flow sensor positions: 2
Oxygen sensor
Type: Galvanic fuel cell
Ventilator pneumatics
Pressure range
at inlet: 240 kPa to 700 kPa/35 psig to 100 psig
Flow
compensation Tec 6 Plus vaporizer Tec 7 vaporizer
range: 200 mL/min to 15 L/min
AN3968-E.qxd 26.10.2005 10:04 Sivu 5
Electrical specifications
Current leakage
100/120 V: < 300µA Primary regulator
diaphragm minimum
220/240 V: < 500µA burst pressure: 2758 kPa/400 psig
Materials
All materials in contact with exhaled patient gases are autoclavable, except
disposable flow sensors and O2 cell. (Autoclavable flow sensors optional).
All materials in contact with patient gas are free of natural rubber latex.
Mechanical
mode: Automatically compensates for compression
losses within the absorber and bellows
assembly
Expiratory
resistance: Pexp Bag Mode Pexp Vent Mode
Flow rate Pressure drop Pressure drop
Note: With patient circuit and wye piece add +0.89 cm H2O
Active adjustable
flow: >30L/mi
AN3968-E.qxd 26.10.2005 10:04 Sivu 8
GE Healthcare GE Healthcare
P.O. Box 7550 P.O. Box 900, FIN-00031 GE, Finland
Madison, WI 53707-7550 Tel. +358 10 394 11
USA Fax +358 9 146 3310
www.gehealthcare.com
AN3968-E/1005