Professional Documents
Culture Documents
: KM-1HH-E
Vol. No. : W1HH-E-01
Workshop Manual
m
co
s.
330 • 330LC
l og
350H • 350LCH
ta
ca
370MTH
ep
Excavator
Service Manual (Manual No. KM-1HH-E) consists of the following three separate volumes;
Technical Manual (Operational Principle) : Vol. No. TO1HH-E
Technical Manual (Troubleshooting) : Vol. No. TT1HH-E
Workshop Manual : Vol. No. W1HH-E
ep
ca
ta
log
s.
co
m
INTRODUCTION
TO THE READER
• This manual is written for an experienced technician • If you have any questions or comments, at if you
to provide technical information needed to maintain found any errors regarding the contents of this
and repair this machine. manual, please contact using “Service Manual
Revision Request Form” at the end of this man-
• Be sure to thoroughly read this manual for cor- ual.
rect product information and service procedures. (Note: Do not tear off the form. Copy it for us-
age.):
Publications Marketing & Product Support
Hitachi Construction Machinery Co. Ltd.
TEL: 81-29-832-7173
FAX: 81-29-831-1162
m
ADDITIONAL REFERENCES co
• Please refer to the materials listed below in addition • Operation Manual of the Engine
to this manual. • Parts Catalog of the Engine
• Hitachi Training Material
• The Operator’s Manual
s.
• The Parts Catalog
og
MANUAL COMPOSITION
• This manual consists of three portions: the Techni- • Information included in the Technical Manual
l
ta
• Information included in the Technical Manual • Information included in the Workshop Manual:
(Operational Principle): technical information needed for maintenance
ep
technical information needed for redelivery and and repair of the machine, tools and devices
delivery, operation and activation of all devices needed for maintenance and repair, maintenance
and systems. standards, and removal/installation and assem-
ble/disassemble procedures.
PAGE NUMBER
Example : T 1-3-5
IN-01
INTRODUCTION
SAFETY ALERT SYMBOL AND HEADLINE
NOTATIONS
In this manual, the following safety alert symbol and • CAUTION:
signal words are used to alert the reader to the Indicated potentially hazardous situation which
potential for personal injury of machine damage. could, if not avoided, result in personal injury or
death.
This is the safety alert symbol. When you see this
symbol, be alert to the potential for personal injury. • IMPORTANT:
Never fail to follow the safety instructions prescribed Indicates a situation which, if not conformed to the
along with the safety alert symbol. instructions, could result in damage to the machine.
The safety alert symbol is also used to draw attention
to component/part weights.
• NOTE:
To avoid injury and damage, be sure to use appropri-
Indicates supplementary technical information or
ate lifting techniques and equipment when lifting
m
know-how.
heavy parts.
co
UNITS USED
s.
• SI Units (International System of Units) are used in Example : 24.5 MPa (250 kgf/cm2, 3560 psi)
this manual.
og
MKSA system units and English units are also A table for conversion from SI units to other system
indicated in parenthheses just behind SI units. units is shown below for reference purposees.
l
ta
To Convert To Convert
Quantity Into Multiply By Quantity Into Multiply By
From From
Length mm in 0.03937 Pressure MPa kgf/cm2 10.197
ca
IN-02
SAFETY
RECOGNIZE SAFETY INFORMATION
001-E01A-0688 SA-688
m
• On machine safety signs, signal words designating
the degree or level of hazard - DANGER, WARN-
co
ING, or CAUTION - are used with the safety alert
symbol.
s.
• DANGER indicates an imminently hazardous
situation which, if not avoided, will result in death
or serious injury.
og
002-E01C-1223
SA-1
Buy now
Hitachi Zaxis 330 330LC 350H 350LCH 370MTH Excavator Workshop +
Technical Manuals PDF
With Instant Download