Professional Documents
Culture Documents
DE - Informationen zu Preisen und Verfügbarkeit in Ihrem Land erhalten Sie über die unten aufgeführten Links:
FR - Pour connaître les tarifs et la disponibilité dans votre pays, cliquez sur l'un des liens suivants:
FOD2741ASDV FOD2741A
EN DE FR
This Datasheet is presented by Dieses Datenblatt wird vom Cette fiche technique est
the manufacturer Hersteller bereitgestellt présentée par le fabricant
FOD2741A, FOD2741B, FOD2741C — Optically Isolated Error Amplifier
August 2008
NC 1 8 LED
8
1
C 2 7 FB
E 3 6 COMP
8
8
NC 4 5 GND 1
1
Typical Application
FAN4803
V1 PWM VO
Control
FOD2741
2 8
6
R1
3 7
5 R2
Output Characteristics
Symbol Parameter Test Conditions Min. Typ. Max. Unit
ICEO Collector Dark Current VCE = 10V (Fig. 5) 50 nA
BVECO Emitter-Collector Voltage Breakdown IE = 100µA 7 V
BVCEO Collector-Emitter Voltage Breakdown IC = 1.0mA 70 V
Transfer Characteristics
Symbol Parameter Test Conditions Min. Typ. Max. Unit
CTR Current Transfer Ratio ILED = 10mA, VCOMP = VFB, 100 200 %
VCE = 5V (Fig. 6)
VCE (SAT) Collector-Emitter Saturation ILED = 10mA, VCOMP = VFB, 0.4 V
Voltage IC = 2.5mA (Fig. 6)
Notes:
4. The deviation parameters VREF(DEV) and IREF(DEV) are defined as the differences between the maximum and
minimum values obtained over the rated temperature range. The average full-range temperature coefficient of the
reference input voltage, ∆VREF, is defined as:
6
{ V REF ( DEV ) /V REF ( T A = 25°C ) } × 10
∆V REF ( ppm/°C ) = ----------------------------------------------------------------------------------------------------
-
∆T A
where ∆TA is the rated operating free-air temperature range of the device.
5. The dynamic impedance is defined as |ZOUT| = ∆VCOMP / ∆ILED. When the device is operating with two external
resistors (see Figure 2), the total dynamic impedance of the circuit is given by:
∆V R1
Z OUT, TOT = -------- ≈ Z OUT × 1 + --------
∆I R2
©2004 Fairchild Semiconductor Corporation www.fairchildsemi.com
FOD2741A, FOD2741B, FOD2741C Rev. 1.0.1 4
FOD2741A, FOD2741B, FOD2741C — Optically Isolated Error Amplifier
Electrical Characteristics (Continued) (TA = 25°C unless otherwise specified)
Isolation Characteristics
Symbol Parameter Test Conditions Min. Typ. Max. Unit
II-O Input-Output Insulation RH = 45%, TA = 25°C, t = 5s, 1.0 µA
Leakage Current VI-O = 3000 VDC(6)
VISO Withstand Insulation RH ≤ 50%, TA = 25°C, t = 1 min.(6) 5000 Vrms
Voltage
RI-O Resistance (Input to Output) VI-O = 500 VDC(6) 1012 Ω
Switching Characteristics
Symbol Parameter Test Conditions Min. Typ. Max. Unit
BW Bandwidth (Fig. 7) 50 kHZ
CMH Common Mode Transient ILED = 0mA, Vcm = 10 VPP, 1.0 kV/µs
Immunity at Output HIGH RL = 2.2kΩ(7) (Fig. 8)
CML Common Mode Transient (ILED = 1mA, Vcm = 10 VPP, 1.0 kV/µs
Immunity at Output LOW RL = 2.2kΩ(7) (Fig. 8)
Notes:
6. Device is considered as a two terminal device: Pins 1, 2, 3 and 4 are shorted together and Pins 5, 6, 7 and 8 are
shorted together.
7. Common mode transient immunity at output high is the maximum tolerable (positive) dVcm/dt on the leading edge
of the common mode impulse signal, Vcm, to assure that the output will remain high. Common mode transient
immunity at output low is the maximum tolerable (negative) dVcm/dt on the trailing edge of the common pulse
signal,Vcm, to assure that the output will remain low.
VF
6 R1 6
3 3
V
V 7 7
VCOMP
VREF R2 VREF
5 5
Figure 1. VREF, VF, ILED (min.) Test Circuit Figure 2. ∆VREF / ∆VCOMP Test Circuit
I(LED) I(OFF)
8 2 8 2
IREF
6 6
3 3
V(LED)
V 7 V 7
R1
5 5
I(LED)
ICEO IC
8 2 8 2
VCE VCE
6 6
3 3
7 V 7
VCOMP
VREF
5 5
IF = 1mA 47Ω
RL 8 1
1µF
VOUT 7 4 VIN
0.1 VPP
0.47V
6 2
5 3
VCC = +5V DC
IF = 0mA (A)
IF = 1mA (B)
R1 8 1
2.2kΩ
VOUT 7 4
A B
6 2
5 3
VCM
_ +
10VP-P
10
0.5
5
0 0.0
-5
-0.5
-10
-15 -1.0
-1 0 1 2 3 –1 0 1 2 3
VCOMP – CATHODE VOLTAGE (V) VCOMP – CATHODE VOLTAGE (V)
Fig. 10 – Reference Voltage vs. Ambient Temperature Fig. 11 – Reference Current vs Ambient Temperature
2.510 1.30
ILED = 10mA ILED = 10mA
2.508 R1 = 10kΩ
2.506 1.25
2.504
2.502 1.20
2.500
2.498 1.15
2.496
2.494 1.10
2.492
2.490 1.05
-40 -20 0 20 40 60 80 100 -40 -20 0 20 40 60 80 100
TA – AMBIENT TEMPERATURE (°C) TA – AMBIENT TEMPERATURE (°C)
Fig. 12 – Off–State Current vs. Ambient Temperature Fig. 13 – Forward Current vs. Forward Voltage
100 20
VCC = 37V
IOFF – OFF–STATE CURRENT (nA)
15
10
25°C
10
70°C 0°C
25
1000
ILED = 20mA
20
100
15
ILED = 10mA
10
10
ILED = 6mA
1
5
ILED = 1mA
0.1 0
-40 -20 0 20 40 60 80 100 0 10 20 30 40 50 60 70 80 90 100
TA – AMBIENT TEMPERATURE (°C) TA – AMBIENT TEMPERATURE (°C)
Fig. 16 – Current Transfer Ratio vs. LED Current Fig. 17 – Saturation Voltage vs. Ambient Temperature
0.26
VCE = 5V
(IC/IF) – CURRENT TRANSFER RATIO (%)
140
0.24
VCE(sat) – SATURATION VOLTAGE (V)
0.22
120
0.20
0°C
100
0.18
25°C
0.16
80
70°C
0.14
60
0.12
40 0.10
0 5 10 15 20 25 30 35 40 45 50 -40 -20 0 20 40 60 80 100
ILED – FORWARD CURRENT (mA) TA – AMBIENT TEMPERATURE (°C)
Fig. 18 – Collector Current vs. Collector Voltage Fig. 19 – Rate of Change Vref to Vout vs. Temperature
35 -0.32
TA = 25°C
30 -0.34
IC – COLLECTOR CURRENT (mA)
ILED = 20mA
25 -0.36
20 -0.38
10 -0.42
ILED = 5mA
5 -0.44
ILED = 1mA
0 -0.46
0 1 2 3 4 5 6 7 8 9 10 -60 -40 -20 0 20 40 60 80 100 120
VCE – COLLECTOR-EMITTER VOLTAGE (V) TEMPERATURE (°C)
-5 RL = 500Ω
RL = 1kΩ
-10
-15
0.1 1 10 100 1000
FREQUENCY (kHz)
10V – 5V
----------------------------------- < 800µA or R COLLECTOR > 6.25kΩ;
R COLLECTOR
0.390 (9.91)
5 6 7 8
0.370 (9.40)
SEATING PLANE
0.070 (1.78)
0.390 (9.91)
0.045 (1.14)
0.370 (9.40)
SEATING PLANE
0.200 (5.08) 0.020 (0.51) MIN
0.140 (3.55) 0.070 (1.78)
0.045 (1.14)
0.154 (3.90) 0.200 (5.08) 0.004 (0.10) MIN
0.120 (3.05) 0.140 (3.55)
0.022 (0.56) 15° MAX
0.016 (0.40)
0.016 (0.41) 0.154 (3.90)
0.008 (0.20)
0.300 (7.62) 0.120 (3.05)
0.100 (2.54) TYP
TYP
0.022 (0.56) 0° to 15°
0.016 (0.41) 0.016 (0.40)
0.008 (0.20)
0.400 (10.16)
0.100 (2.54) TYP
TYP
0.270 (6.86)
0.060 (1.52)
0.250 (6.35)
5 6 7 8 0.100 (2.54)
0.295 (7.49)
0.030 (0.76)
0.415 (10.54)
0.070 (1.78) 0.300 (7.62)
0.045 (1.14) TYP
0.045 (1.14)
0.022 (0.56)
0.016 (0.41)
0.315 (8.00)
0.100 (2.54) MIN
TYP
0.405 (10.30)
Lead Coplanarity : 0.004 (0.10) MAX MAX.
Note:
All dimensions are in inches (millimeters)
Marking Information
2741A 2
6
V XX YY B
3 4 5
Definitions
1 Fairchild logo
2 Device number
3 VDE mark (Note: Only appears on parts ordered with VDE
option – See order entry table)
4 Two digit year code, e.g., ‘03’
5 Two digit work week ranging from ‘01’ to ‘53’
6 Assembly package code
F
A0
W1 W
B0
Reflow Profile
245 C, 10–30 s
300
200
150
Time above 183C, <160 sec
100
50 Ramp up = 2–10C/sec
0
0 0.5 1 1.5 2 2.5 3 3.5 4 4.5
Time (Minute)
* EZSWITCH™ and FlashWriter® are trademarks of System General Corporation, used under license by Fairchild Semiconductor.
DISCLAIMER
FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE
RELIABILITY, FUNCTION, OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR
CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. THESE
SPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILD’S WORLDWIDE TERMS AND CONDITIONS, SPECIFICALLY THE WARRANTY THEREIN,
WHICH COVERS THESE PRODUCTS.
As used herein:
1. Life support devices or systems are devices or systems which, (a) are 2. A critical component in any component of a life support, device, or
intended for surgical implant into the body or (b) support or sustain life, system whose failure to perform can be reasonably expected to
and (c) whose failure to perform when properly used in accordance cause the failure of the life support device or system, or to affect its
with instructions for use provided in the labeling, can be reasonably safety or effectiveness.
expected to result in a significant injury of the user.
ANTI-COUNTERFEITING POLICY
Fairchild Semiconductor Corporation's Anti-Counterfeiting Policy. Fairchild's Anti-Counterfeiting Policy is also stated on our external website, www.fairchildsemi.com,
under Sales Support.
Counterfeiting of semiconductor parts is a growing problem in the industry. All manufacturers of semiconductor products are experiencing counterfeiting of their parts.
Customers who inadvertently purchase counterfeit parts experience many problems such as loss of brand reputation, substandard performance, failed applications,
and increased cost of production and manufacturing delays. Fairchild is taking strong measures to protect ourselves and our customers from the proliferation of
counterfeit parts. Fairchild strongly encourages customers to purchase Fairchild parts either directly from Fairchild or from Authorized Fairchild Distributors who are
listed by country on our web page cited above. Products customers buy either from Fairchild directly or from Authorized Fairchild Distributors are genuine parts, have
full traceability, meet Fairchild's quality standards for handling and storage and provide access to Fairchild's full range of up-to-date technical and product information.
Fairchild and our Authorized Distributors will stand behind all warranties and will appropriately address any warranty issues that may arise. Fairchild will not provide
any warranty coverage or other assistance for parts bought from Unauthorized Sources. Fairchild is committed to combat this global problem and encourage our
customers to do their part in stopping this practice by buying direct or from authorized distributors.
DE - Informationen zu Preisen und Verfügbarkeit in Ihrem Land erhalten Sie über die unten aufgeführten Links:
FR - Pour connaître les tarifs et la disponibilité dans votre pays, cliquez sur l'un des liens suivants:
FOD2741ASDV FOD2741A
EN DE FR
This Datasheet is presented by Dieses Datenblatt wird vom Cette fiche technique est
the manufacturer Hersteller bereitgestellt présentée par le fabricant